Results for “manufacturing rate” — Page 4

NASA NTRSDate not supplied

Thermoplastic Aircraft Manufacturing Model

A manufacturing process to produce 80 single aisle sized thermoplastic composite aircraft a month is presented. Within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) program a baseline aircraft fuselage was designed and modeled based on the Boeing 787 one-piece barrel build, but scaled down to a single aisle aircraft. Key Performance Parameters (KPPs) of recurring cost, non-recurring cost, and weight are calculated from the model. The outcome of this simulation indicated a prohibitively high non-recurring cost, so the thermoplastic team modeled the manufacturing flow for a panelized fuselage concept. The minimum success criteria is a 30% cost reduction and less than two percent increase in weight compared to the baseline aircraft. Automated Fiber Placement (AFP) is used to layup skins, stamp forming is used to make body frames, stringers, and passenger door surround parts. In the model, Co-Fusion was used to consolidate the skin while simultaneously welding on stringers to make stiffened panels. Additional welding technologies were considered to minimize fastener use and a vertical build concept was used for final assembly to reduce factory size. This manufacturing concept for a thermoplastic aircraft indicated a 39% cost and 12% weight savings compared to the baseline. Additional trade studies were conducted using Northrop Grumman’s Automated Stiffener Forming technology to make stringers and stamp forming instead of AFP to make skins.

thermoplastic composites↗

NASA NTRSDate not supplied

Thermoplastic Composite Aircraft Manufacturing Model

A manufacturing process to produce 80 single aisle sized thermoplastic composite aircraft a month is presented. Within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) program a baseline aircraft fuselage was designed and modeled based on the Boeing 787 one-piece barrel build, but scaled down to a single aisle aircraft. Key Performance Parameters (KPPs) of recurring cost, non-recurring cost, and weight are calculated from the model. The outcome of this simulation indicated a prohibitively high non-recurring cost, so the thermoplastic team modeled the manufacturing flow for a panelized fuselage concept. The minimum success criteria is a 30% cost reduction and less than two percent increase in weight compared to the baseline aircraft. Automated Fiber Placement (AFP) is used to layup skins, stamp forming is used to make body frames, stringers, and passenger door surround parts. In the model, Co-Fusion was used to consolidate the skin while simultaneously welding on stringers to make stiffened panels. Additional welding technologies were considered to minimize fastener use and a vertical build concept was used for final assembly to reduce factory size. This manufacturing concept for a thermoplastic aircraft indicated a 39% cost and 12% weight savings compared to the baseline. Additional trade studies were conducted using Northrop Grumman’s Automated Stiffener Forming technology to make stringers and stamp forming instead of AFP to make skins.

thermoplastic composites↗

NASA NTRS1978

Pilot line report: Development of a high efficiency thin silicon solar cell

Experimental technology advances were implemented to increase the conversion efficiency of ultrathin 2cm x 2cm cells, to demonstrate a capability for fabricating such cells at a rate of 10,000 per month, and to fabricate 200 large-area ultrathin cells to determine their feasibility of manufacture. A production rate of 10,000 50 micron m cells per month with lot average AM0 efficiencies of 11.5% was demonstrated, with peak efficiencies of 13.5% obtained. Losses in most stages of the processing were minimized, the remaining exceptions being in the photolithography and metallization steps for front contact generation and breakage handling. The 5cm x 5cm cells were fabricated with a peak yield in excess of 40% for over 10% AM0 efficiency. Greater fabrication volume is needed to fully evaluate the expected yield and efficiency levels for large cells.

Source record↗

NASA NTRSDate not supplied

Open-Hole Testing of Resin Infused Carbon Composite Laminates to Facilitate Damage Growth and Failure Analysis Tools for Structural Design

In manufacturing of carbon-fiber reinforced composite aircraft structures, resin infusion offers a highly repeatable process for manufacturing structural components with resin content control, low labor requirements, and complex curvatures. To further understand the structural capabilities of res-in infused composites (RIC), this study – as part of the NASA-led Hi-Rate Composite Aircraft Manufacturing project efforts – performed open hole tension (OHT) and open hole compression (OHC) testing on RIC laminates. This testing provides information on the damage morphology and growth characteristics of RICs, which fuels the development and evaluation of analysis tools for progressive damage growth and failure responses. X-ray computed tomography (XCT) was implemented on each OHC and OHT specimen prior to mechanical testing to identify preexisting damage and/or defects. Two OHT and OHC specimens were loaded monotonically to failure and an additional OHT and OHC specimen were loaded intermittently at defined conditions and XCT scanned after each run. From the data obtained in this study, damage mechanisms leading to failure were identified, damage morphology and size were assessed, and damage initiation and failure loads were measured.

HiCAM↗

NASA NTRSDate not supplied

The Additive Manufacturing Moment Measure (AM3) Approach to Predictions of Solid Cooling Rate and Time Above Melt

Qualification of a laser powder bed fusion additive manufacturing (LPBF-AM) process requires knowledge of the multi-scale material physics during the process, per part. As the LPBF-AM build occurs, each moment is influenced by the process history. Knowledge of the build sequence can be used to generate a discretized time-space-condition point field that when coupled with a nearest neighbors’ calculation results in a generalized and fully parallel process model computation. This GPU accelerated approach was developed for part-scale analysis of build files along with in-situ process monitoring sensor data and is termed the “Additive Manufacturing Moment Measure” (AM3). The AM3 approach will be presented and then used to evaluate an AM Bench relevant geometry with synchronized in-situ process data, ex-situ nondestructive evaluation, and optical microscopy observations. These comparisons permit a better understanding of how the process actions can affect the LPBF-AM build quality and the signals generated during in-situ process monitoring.

Additive Manufacturing↗

NASA NTRS2018

Systems and Methods for Additive Manufacturing Processes that Strategically Buildup Objects

Systems and methods in accordance with embodiments of the invention implement additive manufacturing techniques that employ different sets of deposition characteristics and/or material formation characteristics during the additive manufacture of an object so as to strategically build up the object. In many embodiments, material used to build up an object is deposited at different deposition rates during the additive manufacture of the object, and the object is thereby strategically built up. In one embodiment, a method of additively manufacturing an object includes: depositing material onto a surface at a first deposition rate so as to define a first region of the object to be additively manufactured; and depositing material onto a surface at a second deposition rate so as to define a second region of the object to be additively manufactured; where the second deposition rate is different from the first deposition rate.

Hofmann, Douglas C.↗

NASA NTRSDate not supplied

Improvements to Stitching Controls for Manufacturing Advanced Stitched Composites

Stitched composites have been extensively studied and have been shown to have benefits over unstitched composites for stiffened structures, including improved damage tolerance, reduced weight, and fewer fasteners. These benefits make stitched composites attractive from a performance perspective, however, the nature of stitching the preforms prior to infusion includes additional manufacturing steps and equipment compared to conventional resin infusion. Stitching of composite material structures at NASA Langley Research Center (LaRC) is performed at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility using control algorithms developed by the lead author. Two deficiencies have been identified in the current control algorithms, and mitigations for these deficiencies were developed within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) project and are presented herein. First, decoupling stitch translation and rotation takes more time for stitching since two robot operation control steps are executed for each stitch. Therefore, a method was developed to determine when to decouple the translation and rotation for stitching, which reduces stitch time by decoupling the operation control steps only when necessary to execute the stitch properly. Second, a correction to the sideslip stitching approach that eliminates a significant portion of the pre- and post-stitching activities was developed. The developed method adjusts the sideslip stitch angle based on the rotations of previous stitches to ensure that the width of the stitching seam remains constant along its length. Constant seam width eliminates observed overlap of the insertion and catcher thread portions for highly curved paths, which maintains the desired uniformity of through-the-thickness architecture along the seam and eliminates the local degradation of properties where the insertion needle is too close to, or crosses, the catcher needle portion of the seam.

stitching↗

NASA NTRS1992

Effects of bleed air extraction on thrust levels on the F404-GE-400 turbofan engine

A ground test was performed to determine the effects of compressor bleed flow extraction on the performance of F404-GE-400 afterburning turbofan engines. The two engines were installed in the F/A-18 High Alpha Research Vehicle at the NASA Dryden Flight Research Facility. A specialized bleed ducting system was installed onto the aircraft to control and measure engine bleed airflow while the aircraft was tied down to a thrust measuring stand. The test was conducted on each engine and at various power settings. The bleed air extraction levels analyzed included flow rates above the manufacturer's maximum specification limit. The measured relationship between thrust and bleed flow extraction was shown to be essentially linear at all power settings with an increase in bleed flow causing a corresponding decrease in thrust. A comparison with the F404-GE-400 steady-state engine simulation showed the estimation to be within +/- 1 percent of measured thrust losses for large increases in bleed flow rate.

Yuhas, Andrew J.↗

NASA NTRS1992

Effects of bleed air extraction of thrust levels on the F404-GE-400 turbofan engine

A ground test was performed to determine the effects of compressor bleed flow extraction on the performance of F404-GE-400 afterburning turbofan engines. The two engines were installed in the F/A-18 High Alpha Research Vehicle at the NASA Dryden Flight Research Facility. A specialized bleed ducting system was installed onto the aircraft to control and measure engine bleed airflow while the aircraft was tied down to a thrust measuring stand. The test was conducted on each engine and at various power settings. The bleed air extraction levels analyzed included flow rates above the manufacturer's maximum specification limit. The measured relationship between thrust and bleed flow extraction was shown to be essentially linear at all power settings with an increase in bleed flow causing a corresponding decrease in thrust. A comparison with the F404-GE-400 steady-state engine simulation showed the estimation to be within +/- 1 percent of measured thrust losses for large increases is bleed flow rate.

Yuhas, Andrew J.↗

NASA NTRSDate not supplied

ISAAC Integrated Structural Assembly of Advanced Composites

The NASA Langley Research Center obtained the Integrated Structural Assembly of Advanced Composites (ISAAC) robotic system in 2014 to add state-of-the-art automated manufacturing of composites to our traditional in-house design, analysis, and experimentation capabilities. ISAAC is used to explore fabrication of parts with novel designs and for research into new composite manufacturing techniques. Automated fiber placement (AFP) was the initial manufacturing capability on ISAAC and has been used to support a range of aeronautics and space projects including the Advanced Composites Project (ACP), Composites for Exploration Upper Stage (CEUS), and Advanced Air Transportation Technologies (AATT). In addition to AFP, ISAAC can now provide through-thickness reinforcement of composites by adding stitches through dry fabric prior to resin infusion. Stitching is of interest since it can improve damage tolerance, reduce final assembly time, and reduce inspection requirements. ISSAC can stitch traditional single-needle seams and perform stitching operations using two needles when access is only available to one side of the part. Stitching capability is being advanced in the High-Rate Composites Aircraft Manufacturing (HiCAM) project today. This lecture will describe the work with ISAAC today and new exciting plans for the future.

automated fiber placement↗

NASA NTRS1980

JANTX2N4150 transistor

Report evaluates effects of power and temperature overstress on General Semiconductor and Transitron devices. General Semiconductor lot exceeded 50 percent failure 500 hours into 125 percent maximum rated power test. Catastrophic failure rates differed between manufacturers. Modes of failure are analyzed.

Source record↗

NASA NTRS1983

High density tape/head interface study

The high energy (H sub c approximately or = to 650 oersteds) tapes and high track density (84 tracks per inch) heads investigated had, as its goal, the definition of optimum combinations of head and tape, including the control required of their interfacial dynamics that would enable the manufacture of high rate (150 Mbps) digital tape recorders for unattended space flight.

Csengery, L. C.↗

NASA NTRS1988

Ozone profile measurements at McMurdo Station Antarctica during the spring of 1987

During the Antarctic spring of 1986, 33 ozone soundings were conducted from McMurdo Station. These data indicated that the springtime decrease in ozone occurred rapidly between the altitudes of 12 and 20 km. During 1987, these measurements were repeated with 50 soundings between 29 August and 9 November. Digital conversions of standard electrochemical cell ozonesondes were again employed. The ozonesonde pumps were individually calibrated for flow rate as the high altitude performance of these pumps have been in question. While these uncertainties are not large in the region of the ozone hole, they are significant at high altitude and apparently resulted in an underestimate of total ozone of about 7 percent (average) as compared to the Total Ozone Mapping Spectrometer (TOMS) in 1986, when the flow rate recommended by the manufacturer was used. At the upper altitudes (approx. 30 km) the flow rate may be overestimated by as much as 15 percent using recommended values (see Harder et al., The UW Digital Ozonesonde: Characteristics and Flow Rate Calibration, poster paper, this workshop). These upper level values are used in the extrapolation, at constant mixing ratio, required to complete the sounding for total ozone. The first sounding was on 29 August, prior to major ozone depletion, when 274 DU total ozone (25 DU extrapolated) was observed. By early October total ozone had decreased to the 150 DU range; it then increased during mid-October owing to motion of the vortex and returned to a value of 148 DU (29 DU extrapolated) on 27 October.

Hofmann, D. J.↗

NASA NTRS2013

Process Optimization of Bismaleimide (BMI) Resin Infused Carbon Fiber Composite

Bismaleimide (BMI) resins are an attractive new addition to world-wide composite applications. This type of thermosetting polyimide provides several unique characteristics such as excellent physical property retention at elevated temperatures and in wet environments, constant electrical properties over a vast array of temperature settings, and nonflammability properties as well. This makes BMI a popular choice in advance composites and electronics applications [I]. Bismaleimide-2 (BMI-2) resin was used to infuse intermediate modulus 7 (IM7) based carbon fiber. Two panel configurations consisting of 4 plies with [+45deg, 90deg]2 and [0deg]4 orientations were fabricated. For tensile testing, a [90deg]4 configuration was tested by rotating the [0deg]4 configirration to lie orthogonal with the load direction of the test fixture. Curing of the BMI-2/IM7 system utilized an optimal infusion process which focused on the integration of the manufacturer-recommended ramp rates,. hold times, and cure temperatures. Completion of the cure cycle for the BMI-2/IM7 composite yielded a product with multiple surface voids determined through visual and metallographic observation. Although the curing cycle was the same for the three panellayups, the surface voids that remained within the material post-cure were different in abundance, shape, and size. For tensile testing, the [0deg]4 layup had a 19.9% and 21.7% greater average tensile strain performance compared to the [90deg]4 and [+45deg, 90deg, 90deg,-45degg] layups, respectively, at failure. For tensile stress performance, the [0deg]4 layup had a 5.8% and 34.0% greater average performance% than the [90deg]4 and [+45deg, 90deg, 90deg,-45deg] layups.

Ehrlich, Joshua W.↗

NASA NTRSDate not supplied

Effects of Defects Analysis and Sizing Framework for Efficient Design of Composite Structures

Design of large composite structures requires striking a balance between permitted flaw size,strength margins, weight, and production rate. Stringent requirements manufacturing flaws can result in a lightweight structure because the strength properties are assumed to be closer to pristine. However, these stringent requirements can lead to production delays due to increased inspection and rework needed during the layup and rejection of parts after cure. Conversely, permitting larger flaws can reduce production delays, but will likely result in a heavier structure due to increased conservatism needed to maintain acceptable structural margins. The tradeoff between these criteria can vary between different structures and material systems, so the balance between manufacturing and design requirements is always a moving target. Assessment of this tradeoff requires having the ability to quickly evaluate the impact of flaw size on strength margin across an entire structure for a large number of load cases. The approach taken in this work is to implement an effects of defects analysis and sizing framework within HyperX. HyperX performs optimization of composite structures; this capability has been enhanced to include structural flaw data in the margin of safety calculations performed during optimization. Both the flaw import process and analysis of flaws have been generalized such that any flaw type from any source can be considered. The resulting tool enables rapid assessment of the impact of defects both at a vehicle and part level.

Effects of defects↗

NASA NTRSDate not supplied

Effects of Defects Analysis and Sizing Framework for Efficient Design of Composite Structures

Design of large composite structures requires striking a balance between permitted flaw size,strength margins, weight, and production rate. Stringent requirements manufacturing flaws can result in a lightweight structure because the strength properties are assumed to be closer to pristine. However, these stringent requirements can lead to production delays due to increased inspection and rework needed during the layup and rejection of parts after cure. Conversely, permitting larger flaws can reduce production delays, but will likely result in a heavier structure due to increased conservatism needed to maintain acceptable structural margins. The tradeoff between these criteria can vary between different structures and material systems, so the balance between manufacturing and design requirements is always a moving target. Assessment of this tradeoff requires having the ability to quickly evaluate the impact of flaw size on strength margin across an entire structure for a large number of load cases. The approach taken in this work is to implement an effects of defects analysis and sizing framework within HyperX. HyperX performs optimization of composite structures; this capability has been enhanced to include structural flaw data in the margin of safety calculations performed during optimization. Both the flaw import process and analysis of flaws have been generalized such that any flaw type from any source can be considered. The resulting tool enables rapid assessment of the impact of defects both at a vehicle and part level.

Effects of defects↗

NASA NTRS2023

Progressive Damage and Failure Analysis of Thermoplastic Composites in Low Velocity Impact Using MAT299

As part of the NASA Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project, state-of-the-art progressive damage and failure analysis (PDFA) tools developed for use with thermosets are being evaluated for use in modeling alternative material systems, like thermoplastics. Experimental low-velocity impact data of a thermoplastic material system, AS4D/PEKK-FC, is presented and includes characterization of the impact damage mechanisms as well as associated load and displacement data. Following the presentation of experimental results, two simulation approaches using the PDFA tool MAT299 in the commercial off-the-shelf finite element software LS-DYNA are employed to predict damage area and force-displacement responses of thermoplastic panels subjected to various impact energies. The first modeling method uses solid elements with a high-density mesh and a ply-by-ply modeling approach similar to previously published work for thermosets. This method has the capability of capturing individual crack development, progression, and delamination on a per ply basis. The second modeling method uses TSHELL elements that have in-plane dimensions that are an order of magnitude larger than the elements used in the solid element approach and reduces the number of elements through the thickness of the laminate. The second method produces a lower-fidelity model with reduced run times that is incapable of monitoring every delamination plane and damage within each ply. Results from both simulation methods are compared to experiment, and limitations of the methods are discussed.

Composite material↗

NASA NTRS2023

Progressive Damage and Failure Analysis of Thermoplastic Composites in Low Velocity Impact Using MAT299

As part of the NASA Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project, state-of-the-art progressive damage and failure analysis (PDFA) tools developed for use with thermosets are being evaluated for use in modeling alternative material systems, like thermoplastics. Experimental low-velocity impact data of a thermoplastic material system, AS4D/PEKK-FC, is presented and includes characterization of the impact damage mechanisms as well as associated load and displacement data. Following the presentation of experimental results, two simulation approaches using the PDFA tool MAT299 in the commercial off-the-shelf finite element software LS-DYNA are employed to predict damage area and force-displacement responses of thermoplastic panels subjected to various impact energies. The first modeling method uses solid elements with a high-density mesh and a ply-by-ply modeling approach similar to previously published work for thermosets. This method has the capability of capturing individual crack development, progression, and delamination on a per ply basis. The second modeling method uses TSHELL elements that have in-plane dimensions that are an order of magnitude larger than the elements used in the solid element approach and reduces the number of elements through the thickness of the laminate. The second method produces a lower-fidelity model with reduced run times that is incapable of monitoring every delamination plane and damage within each ply. Results from both simulation methods are compared to experiment, and limitations of the methods are discussed.

Composite material↗