Search NASA⌕ Search

SEARCH · Search NASA

Results for “performance improvements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Performance Improvement of LTS Undulators for Synchrotron Light Sources

The joint expertise of ANL and FNAL has led to the production of $\text{Nb}_{3}\text{Sn}$ undulator magnets in operation in the ANL Advanced Photon Source (APS). These magnets showed performance reproducibility close to the short sample limit, and a design field increase of 20% at 820 A. However, the long training did not allow obtaining the expected 50% increase of the on-axis magnetic field with respect to the ∼1 T produced at 450 A current in the ANL NbTi undulator. To address this, 10-pole long undulator prototypes were fabricated, and CTD-101K was replaced as impregnation material with TELENE, an organic olefin-based thermosetting dicyclopentadiene resin produced by RIMTEC Corporation, Japan. Training and magnet retraining after a thermal cycle were nearly eliminated, with only a couple of quenches needed before reaching short sample limit at over 1,100 A. TELENE will enable operation of $\text{Nb}_{3}\text{Sn}$ undulators much closer to their short sample limit, expanding the energy range and brightness intensity of light sources. TELENE is Co-60 gamma radiation resistant up to 7–8 MGy, and therefore already applicable to impregnate planar, helical and universal devices operating in lower radiation environments than high energy colliders.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Performance improvements of the windowed multipole formalism using a rational fraction approximation of the Faddeeva function

The windowed multipole (WMP) formalism was introduced as a way to calculate Doppler broadened cross sections on the fly during Monte Carlo simulations. While more arithmetic is needed compared to point-wise cross section look-ups, performance remained competitive from the large memory reductions and sequential data access. The single most expensive function call in a depleted fuel assembly problem using WMP comes from the evaluation of the Faddeeva function, which previously relied on a highly accurate, highly-branching algorithm. This paper explores the use of rational fraction approximations tailored to the domain interest of reactor physics applications and the development of lower accuracy approximations sufficient for our application. The rational approximations were implemented and tested in OpenMC on an infinite medium problem to stress the cross section calculation routine and a PWR assembly problem. In both cases, the rational approximation nearly eliminated the ∼ 20% penalty previously observed when comparing to point-wise libraries. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Active Learning-driven Quantitative Synthesis-Structure-Property Relations for Improving Performance and Revealing Active Sites of Nitrogen-Doped Carbon for the Hydrogen Evolution Reaction

While quantitative structure-properties relations (QSPRs) have been developed successfully in multiple fields, catalyst synthesis affects structure and in turn performance, making simple QSPRs inadequate. Furthermore, catalysts often have multiple active sites preventing one from obtaining insights into structure-property relations. Here, we develop a data-driven quantitative synthesis-structure-property relation (QS2PRs) methodology to elucidate correlations between catalyst synthesis conditions, structural properties as well as observed performance and to provide fundamental insights into active sites and a systematic way to optimize practical catalysts. Here, we demonstrate the approach to the synthesis of nitrogen-doped catalysts (NDC) made via pyrolysis for the performance of the electrochemical hydrogen evolution reaction (HER), quantified by the onset potential and the current density. We determine crystallinity, nitrogen species type and fraction, surface area, and pore structure of the NDC’s using XRD, XPS, and BET characterization. We demonstrated that an active learning-based optimization combined with various elementary machine learning tools (regression, principal component analysis, partial least squares) can efficiently identify optimum pyrolysis conditions to tune structural characteristics and performance with concomitant savings in materials and experimental time. Unlike previous reports on the importance of pyridinic or graphitic nitrogen, we discover that the electrochemical performance is not driven by a single catalyst property; rather, it arises from a multivariate influence of nitrogen dopants, pore structure and disorder in the NDC materials. Identification of active sites can help mechanistic understanding and further catalyst improvement.

42 ENGINEERING↗
DOE OSTI2022

Improve Performance and Cost for Steam Turbine Maintenance, Repair, and Overhaul Using Additive Manufacturing

The overall objective was to develop additive-manufacturing-enabled repair solutions for last stage bucket (LSB) and additive-manufacturing-enabled packing rings (PRs) for coal-fired steam turbines with the goal of reducing routine maintenance, repair, and overhaul (MRO) cost and improving the operating efficiency of steam turbines. GE Steam Power (GESP) and GE Gas Power (GEGP) provided technical and commercial consulting to GER with insights on steam turbine MRO design requirements, MRO duration and costs, and an overall commercialization strategy for the additive manufacturing technologies developed in the proposed effort.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2026

Improving Performance via Energy Efficiency JUSTIFI: Open-Source Software for Identifying and Quantifying Non-Energy Benefits

Energy efficiency is pivotal to achieving operational excellence, as it enhances value while reducing waste. This presentation explores the integration of non-energy benefits (NEBs) into energy efficiency projects, which can lead to risk reduction, value creation, and cost savings. By quantifying NEBs - such as improved safety, decreased pollution, and increased productivity - companies can strengthen their business cases for energy investments, ultimately improving payback periods and aligning with strategic goals. Designed for a diverse audience, from trained auditors to novices in energy assessments, we have developed open-source software called JUSTIFI, NEB finding methodology, and training materials which build on existing frameworks and leverages resources from the U.S. Department of Energy and Better Plants energy system analysis software suite such as MEASUR. This work aims to maximize ROI through NEB identification, utilizing tools like JUSTIFI and the NEBs Discovery Protocol.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Energy Model of an Air Source Heat Pump to Explore Performance Improvements under Cold Conditions: A Python Framework: Preprint

Replacing combustion appliances with heat pumps can be part of a strategy to electrify buildings. When their electricity is supplied by renewables, the adoption of heat pumps for space heating may help curb the carbon dioxide emissions inherent to traditional heating systems that burn natural gas or coal. When operating in very cold climates, however, heat pump performance deteriorates, sometimes requiring backup heating supplied by electric resistances or other sources to continue to function. To avoid the use of electric resistances, complementary technologies, like thermal energy storage, solar collectors, or alternative refrigerants, have been explored in recent years. In this study, we present an open-source Python-based numerical model developed to evaluate the annual hourly performance of an air source heat pump (ASHP) operating in the USA. Simulation results include coefficient of performance and heating capacity. The model, validated with experimental results, will be employed in the future to investigate the feasibility of integrating thermal energy storage and other technologies into ASHPs operating in cold climates.

cold climate↗
DOE OSTI2023

Optimization of a Residential Air Source Heat Pump using Refrigerants with GWP <150 for Improved Performance and Reduced Emission

Using low-GWP refrigerants can reduce the Green House Gas (GHG) emission of heat pump systems. Heat exchangers and compressors are the key components and have a prominent impact on system performance, significant research is devoted to reducing the cost of the heat exchangers while achieving the same or better system performance with refrigerant charge reduction.To better understand the environmental impacts of optimized systems with low-GWP refrigerants, Life Cycle Climate Performance (LCCP) evaluation method was used to evaluate the direct and indirect emissions of the system over the course of its lifetime from manufacturing to disposal. The DOE/ORNL Heat Pump Design Model (HPDM) is used to evaluate the performance of heat pumps. Multi-objective optimizations using Particle Swarm Optimization (PSO) algorithm are performed on a 3-ton R410A residential air source heat pump on market. Seven R410A alternatives, i.e., R32, R454B, R454C, R455A, R457A, R1234yf and R1234ze(E) are investigated. The last five fluids have GWP lower than 150.As a result, 5.5%-12.8% seasonal energy efficiency ratio 2 (SEER2) improvement is achieved, and the optimized systems reduce life cycle CO2 emission by 8.5%-28.6% with GWP lower than 150 refrigerants. The optimal heat exchangers can fit into the original R410A fan-coil units; therefore, the proposed design method establishes a production and installation path to produce cost-effective low-GWP heat pumps easily accepted by end users.

Li, Zhenning↗
DOE OSTI2022

Atomic layer deposition of lithium zirconium oxides for the improved performance of lithium-ion batteries

Recently there has been increasing interest to develop lithium-containing films as solid-state electrolytes or surface coatings for lithium-ion batteries (LIBs) and related systems. Here, in this study, we for the first time investigated the thin film growth of lithium zirconium oxides (Li x Zr y O or LZOs) through combining two individual atomic layer deposition (ALD) processes of ZrO 2 and LiOH, i.e., sub-ALD of ZrO 2 and LiOH. We revealed that the hygroscopic nature of the LiOH component has a big impact on the growth of LZOs. We found that an increased temperature to 225 °C was more effective than an elongated purge to mitigate the adverse effects of physisorbed H 2 O. We further discovered that, during the resultant LZO super-ALD processes, the growth of sub-ALD LiOH has been promoted while the growth of sub-ALD ZrO 2 has been inhibited. In this study, a suite of instruments has been applied to characterize the LZO super-ALD processes and the resultant LZO films, including in situ quartz crystal microbalance (QCM), scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM), atomic force microscopy (AFM), synchrotron-based X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Furthermore, we applied the resulting LZO films over LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) cathodes in LIBs and demonstrated that the LZO coating films could evidently improve the lithium-ion insertion and extraction rates of the NMC622 electrodes up to 3.4 and 2.6 times, respectively. The LZO-coated NMC622 cathodes exhibited much better performance than the uncoated NMC622 ones.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigation of Numerical Methods for Performance Improvement of MOOSE-based System Analysis Codes

The main objective of this study is to investigate the feasibility of implementation of staggered-grid finite volume method (SG-FVM) using the MOOSE framework to support the development of the advanced system analysis code SAM. This study successfully demonstrated the integration of staggered-grid finite volume method in the application level using the MOOSE framework, although not in the framework level which should be investigated in the future. Several important properties of the implemented SG-FVM, e.g., high-order spatial accuracy and monotonicity preserving, have been demonstrated with selected numerical test cases. The superior performance in execution time was also evident based on a selected one- dimensional flow problem in a loop configuration.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

InGaSb Defect Filter Layer to Improve Performance of GaSb Solar Cells Grown on GaAs Substrates

The reduction of the threading dislocation density in metamorphic GaSb grown on GaAs substrates through the use of InGaSb defect filter layers has been investigated. More specifically, we study the effects of strain and thickness on the ability of a InGaSb defect filter layer to reduce threading dislocations in GaSb solar cells grown on GaAs substrates. The strain between the GaSb metamorphic layer on GaAs substrate (99.5% relaxed) and the InGaSb defect filter layer is varied by changing the indium composition in the InGaSb layer. Here, it is demonstrated that an InGaSb defect filter layer with 0.6% strain is more effective for blocking threading dislocations compared with higher-strain layers, resulting in improved short-circuit current (J sc ) and open-circuit voltage (V oc ) for the metamorphic GaSb solar cell. The optimization of the defect filter layer involves varying the thickness of the layer to achieve the lowest possible threading dislocation density. This also takes into account the critical thickness of the InGaSb layer on GaSb to avoid generation of threading dislocations from the InGaSb layer itself. It is shown that adding an In 0.11 Ga 0.89 Sb defect filter layer with thickness of 250 nm and 0.6% strain beneath a GaSb solar cell grown on a GaAs substrate improves V oc from 0.1 V to 0.16 V and J sc from 19.7 mA/cm 2 to 24.7 mA/cm 2 .

36 MATERIALS SCIENCE↗
DOE OSTI2024

Transient Optimization of the Cryogenic Moderator System Controller at the Spallation Neutron Source for Improved Performance

The high-energy neutron beam generated at the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory is moderated to use cold (slow) neutrons for scientific discoveries. The Cryogenic Moderator System (CMS) removes heat from the neutron beam using cryogenic hydrogen (H 2 ) moderators connected via heat exchangers to a helium (He) refrigeration loop that dissipates heat using a compressor-brake system. However, the CMS is affected by sporadic losses in beam power, referred to as "beam trips," as these events generate significant disturbances in cooling requirements. To accommodate the heat load transients during beam trips, the CMS uses a decentralized control strategy consisting of four flow valves and one electric heater adjusted by independent proportional-integral (PI) controllers. During the CMS’s initial commissioning, the PI gains were calibrated based only on tracking performance, overlooking their effectiveness in disturbance rejection. A data-driven, control-oriented closed-loop model was developed to recalibrate the PI gains and minimize the transient disturbances caused by beam trips. The model consists of three main components: (1) a physics-based model of the He refrigeration loop, (2) a machine-learning model of the cryogenic H 2 cooling trains, and (3) the control logic used for feedback set-point tracking. Experimental results showed that the recalibrated gains obtained in this study improved the CMS’s transient response during beam trips.

Maldonado Puente, Bryan↗
DOE OSTI2025

Challenges in Tracking Waste Reduction Performance Improvement in Manufacturing Plants

The recently released Circularity Gap Report 2023 by the Circle Economy Foundation states that the circularity score for the global economy is declining. The US Environmental Protection Agency (EPA) tracked municipal solid waste from 1960 to 2018 and found that 50% of the waste was destined for landfills. EPA estimates that US industry is responsible for 2.7 Gt of solid nonhazardous waste annually in the US mostly linear economy model. The circular economy framework aims to decouple economic value generation from the extraction of virgin materials from nature. The linear model of material extraction and disposal at the end of life is highly unsustainable. Manufacturing companies are adopting ambitious waste reduction targets to achieve sustainability. Through the Better Plants program, US DOE has established the Waste Reduction Network, which offers technical assistance to partners to achieve their ambitious waste reduction goals. Basic requirements of establishing a target include identifying a baseline, quantifying waste performance, and measuring progress over time. One problem faced by industry is unstandardized metrics for quantifying waste performance that may not be well suited to demonstrate progress. This paper studies traditional methods used to measure waste performance and highlights advantages, disadvantages, and limitations of each method. It also examines the suitability of applying the methods in different manufacturing circumstances. Finally, the paper presents a case study of a large manufacturer that faced inconsistencies in its tracked measurement metric. A solution was proposed and implemented to alter the methodology to enable more accurate waste performance tracking against a baseline.

circular economy↗
DOE OSTI2024

Challenges in Tracking Waste Reduction Performance Improvement in Manufacturing Plants

The recently released Circularity Gap Report 2023 by Circle Economy Foundation found that the circularity score for the global economy is declining. This indicates that material extraction from virgin sources is climbing over earlier years. As per data released by US Geological Survey, material use in the US economy has increased exponentially with the expanding US economy over last century. EPA tracked municipal solid waste from 1960 to 2018 and found that 50% of the waste is destined for landfills. EPA estimates that US industry is responsible for 2.7 billion ton of solid non-hazardous waste annually in our mostly linear economy model. The circular economy framework aims at decoupling economic value generation from virgin materials extraction from nature. The linear model of material extraction and disposal at end of life is highly unsustainable. Manufacturing companies have realized this and in their commitments to sustainability are adopting ambitious waste reduction targets. Through Better Plants program US Department of Energy has established Waste Reduction Network where it is offering technical assistance to partners to achieve these ambitious waste reduction goals. Basic requirements of establishing a target include identifying a baseline, quantifying waste performance, and measuring progress over time. One problem faced by industry is the unstandardized metrics to quantify waste performance that may not be well suited to demonstrate progress. In this paper, we research methods traditionally used to measure waste performance and highlight advantages, gaps and limitations of each method. Suitability of the methods applicable to different manufacturing circumstances are also examined. Finally, we present a case study of a large manufacturer that faced inconsistencies in their tracked measurement metric. A solution was proposed to alter the methodology to enable more accurate waste performance tracking against a baseline.

Chaudhari, Subodh↗