Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microphonics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

An experimental study of the noise generating mechanisms in supersonic jets

Flow fluctuation measurements with normal and X-wire hot-wire probes and acoustic measurements with a traversing condenser microphone were carried out in small air jets in the Mach number range from M = 0.9 to 2.5. One of the most successful studies involved a moderate Reynolds number M = 2.1 jet. The large scale turbulence properties in the jet, and the noise radiation were characterized. A parallel study involved similar measurements on a low Reynolds number M = 0.9 jet. These measurements show that there are important differences in the noise generation process of the M = 0.9 jet in comparison with low supersonic Mach number (M = 1.4) jets. Problems encounted while performing X-wire measurements in low Reynolds number jets of M = 2.1 and 2.5, and in installing a vacuum pump are discussed.

Mclaughlin, D. K.↗

Pressure and velocity measurements in a three dimensional wall jet

In three recent papers, some results of an experimental investigation of a freely expanding coflowing jet as well as a three dimensional wall jet have been presented. A flat plate as well as a curved wall surface intended to model a wing-flap combination in a high lift V/STOL configuration have been investigated. In these papers, the ratio of the jet exit plane velocity to the free stream velocity, was 5.1. This paper explores the effects of increasing the velocity ratio. The quantities measured include the width of the mixing region, the mean velocity field, turbulent intensities and time scales. In addition, wall and static pressure-velocity correlations and coherences are presented. The velocity measurements are made using a laser Doppler velocimeter with a phase-locked loop processor. The fluctuating pressures are monitored using condenser-type microphones.

Catalano, G. D.↗

Measured and predicted noise of the AVCO-Lycoming YF-102 turbofan engine

Acoustic testing of the AVCO-Lycoming YF-102 turbofan engine was done on a static test stand at Lewis Research Center in support of the Quiet Short-Haul Research Aircraft (QSRA) acoustic design. Overall noise levels are dominated by the fan noise emanating from the exhaust duct, except at high power settings when combination tones are generated in the fan inlet. Component noise levels, calculated by noise prediction methods developed at Lewis Research Center for the ANOP program, are in reasonable agreement with the measured results. Far-field microphones placed at ground level were found superior to those at engine centerline height, even at high frequencies.

Clark, B. J.↗

Flowfield and acoustic properties of a Mach number 0.9 jet at a low Reynolds number

An anechoic vacuum chamber test facility is used to assess the flow field and acoustic properties of a jet with a low Reynolds number of about 3600 and a Mach number of 0.9. A conventional Pitot pressure probe is used to monitor the mean flow field, a hot-wire probe is employed to detect flow fluctuations, and the acoustic field is probed by condenser microphones. The jet is operated at the low Reynolds number in order to examine the behavior of the large-scale 'orderly' structure with particular emphasis on its noise-generating capabilities. It is shown that a nonlinear mechanism involving the large-scale flow instability is responsible for a dominant portion of the noise generated from the jet.

Stromberg, J. L.↗

Separation of core noise and jet noise

A method of identification and measurement of core noise and jet noise separately has been developed based on cross-correlation of signals from microphones located at widely separated angles in the far field of a jet. The different coherent properties of core noise and jet noise are used in this method to achieve this separation. Experimental data obtained in a small scale facility is analyzed to demonstrate that this method can be used successfully to separate the mean square pressures of core noise and jet noise.

Parthasarathy, S. P.↗

Quasi-periodic structure of a turbulent jet

The instantaneous near field pressure fluctuations of an axisymmetric subsonic jet were measured by using a longitudinal and an azimuthal microphone arrays in order to qualitatively determine the behaviors of the quasi-periodic structure within the flow. Statistical analysis is used to explain the characteristic of the pressure signals. In addition to the information obtained by forming the power spectral density, auto- and cross-correlation functions, two types of signals are extracted through a conditional probability analysis to represent the quasi-periodic and the random fine structures within the turbulent jet. The quasi-periodic structure first appears as a rolling up of the mixing layer flow within one nozzle diameter downstream of the exit, then becomes fully developed at approximately 3 nozzle diameters downstream with a preferred Strouhal number range 0.3-0.4, and finally disappears beyond the end of potential core. This behavior is also reflected in the variation of the convection velocity.

Maestrello, L.↗

On acoustic intensity measurements in the presence of mean flow

A theoretical analysis demonstrates that the technique of measuring acoustic intensity by means of cross correlation between nearby microphones cannot, in general, be extended to situations in which there is mean flow. However, it may be possible to use this technique to measure intensities in ducts with mean flow at frequencies below their cutoff frequencies.

Munro, D. H.↗

Kilovolt vacuum feed through is less noisy

Electrical feedthrough connects both low-voltage and high-voltage signals between cryogenic environment and "outside world." Developed for cooled germanium gamma-ray detector, feedthrough has especially low capacitance and low sensitivity to microphonic noise. Its high-voltage lead is free of corona discharge and electrical breakdown to at least 5 kV.

Howell, L. D.↗

Applications of diffraction theory to aeroacoustics

The fundamentals of diffraction theory were reviewed and applied to several problems of aircraft noise generation, propagation, and measurement. The general acoustic diffraction problem is defined and the governing equations were set down. Diffraction phenomena are illustrated using the classical problem of the diffraction of a plane wave by a half-plane. Infinite series and geometric acoustic methods for solving diffraction problems are described. Four applications of diffraction theory are discussed: the selection of an appropriate shape for a microphone, the use of aircraft wings to shield the community from engine noise, the reflection of engine noise from an aircraft fuselage, and the radiation of trailing edge noise.

Lansing, D. L.↗

Evaluation of approximate methods for the prediction of noise shielding by airframe components

An evaluation of some approximate methods for the prediction of shielding of monochromatic sound and broadband noise by aircraft components is reported. Anechoic-chamber measurements of the shielding of a point source by various simple geometric shapes were made and the measured values compared with those calculated by the superposition of asymptotic closed-form solutions for the shielding by a semi-infinite plane barrier. The shields used in the measurements consisted of rectangular plates, a circular cylinder, and a rectangular plate attached to the cylinder to simulate a wing-body combination. The normalized frequency, defined as a product of the acoustic wave number and either the plate width or cylinder diameter, ranged from 4.6 to 114. Microphone traverses in front of the rectangular plates and cylinders generally showed a series of diffraction bands that matched those predicted by the approximate methods, except for differences in the magnitudes of the attenuation minima which can be attributed to experimental inaccuracies. The shielding of wing-body combinations was predicted by modifications of the approximations used for rectangular and cylindrical shielding. Although the approximations failed to predict diffraction patterns in certain regions, they did predict the average level of wing-body shielding with an average deviation of less than 3 dB.

Ahtye, W. F.↗

An experimental study of the structure and acoustic field of a jet in a cross stream

The plane of symmetry of a high speed circular jet was surveyed to measure the mean and turbulent velocity fields by using constant temperature hot wire anemometry. The intensity of the noise radiated from the jet was determined in the tunnel test section by utilizing the cross-correlation at a particular time delay between the signals of two microphones suitably located along a given direction. Experimental results indicate that the turbulent intensity inside the crossflow jet increases by a factor of (1 + 1/2) as compared to the turbulent intensity of the same jet under free conditions, with r indicating the ratio of the jet velocity by the cross stream velocity. The peak observed in the turbulence spectra obtained inside the potential core of the jet has a frequency that increases by the same factor with respect to the corresponding frequency measured in the case of the free jet. The noise radiated by the jet becomes more intense as the crossflow velocity increases. The measured acoustic intensity of the crossflow jet is higher than the value which would be expected from the increase of the turbulent intensity only.

Camelier, I.↗

Miniature piezoresistive solid state integrated pressure sensors

The characteristics of silicon pressure sensors with an ultra-small diaphragm are described. The pressure sensors utilize rectangular diaphragm as small as 0.0127 x 0.0254 cm and a p-type Wheatstone bridge consisting of diffused piezoresistive elements, 0.000254 cm by 0.00254 cm. These sensors exhibit as high as 0.5 MHz natural frequency and 1 mV/V/psi pressure sensitivity. Fabrication techniques and high frequency results from shock tube testing and low frequency comparison with microphones are presented.

Kahng, S. K.↗

Effect of grazing flow on the nonlinear acoustic behavior of helmholtz resonators

A semi empirical fluid mechanical model is derived of the acoustic behavior of thin walled single orifice Helmholtz resonators in a grazing flow environment. The model assumes that the flow field incident to a resonator orifice consists of a spherical sound particle velocity field superimposed upon a mean grazing flow. The incident and cavity sound fields are connected in terms of an orifice discharge coefficient whose values are determined experimentally using the two microphone method. With regard to its application to rocket motor interiors, the most important finding of this study is that the acoustic impedance of Helmholtz resonators is affected by grazing flow when the product of the amplitude of the sound pressure incident to the resonator orifice and the rocket motor interior mean grazing flow speed are less than 0.5. For values greater than 0.5, the acoustic impedance is independent of the grazing flow.

Hersh, A. S.↗

Evaluation of Aero Commander sidewall vibration and interior acoustic data: Static operations

Results for the vibration measured at five locations on the fuselage structure during static operations are presented. The analysis was concerned with the magnitude of the vibration and the relative phase between different locations, the frequency response (inertance) functions between the exterior pressure field and the vibration, and the coherent output power functions at interior microphone locations based on sidewall vibration. Fuselage skin panels near the plane of rotation of the propeller accept propeller noise excitation more efficiently than they do exhaust noise.

Piersol, A. G.↗

Noise generation by a lifting wing/flap combination at Reynolds numbers to 2.8 x 10 to the 6th

Measurements relating to the noise source location and intensity within various frequency bands were made for an 0.75 m-chord wing/flap model installed in the Ames 7 x 10-foot wind tunnel. A directional microphone system, located outside the open-wall tunnel was scanned in a two-dimensional array of aiming points about the positive-pressure side of the model to determine the principal locations of noise production, and the intensity of each of these. It was found for the case of the flaps being differentially deflected (0 deg, 35 deg) at the half-span station that noise production was concentrated in the immediate region of the resultant surface discontinuity. For equal deflection of the halves (0 deg, 0 deg or 35 deg, 35 deg), noise was produced uniformly along the length of the gap between the wing and the flap. Simulated flap-mounting brackets generated considerable noise in certain cases, but reduced the noise in others. Trailing edge noise did not appear to be important in comparison with other sources.

Kendall, J. M.↗

Boundary-layer transition on a 10-deg cone - Wind tunnel/flight correlation

Boundary-layer transition location measurements were made on a 10-deg sharp cone in 23 wind tunnels of the US and Europe and in flight. The data were acquired at subsonic, transonic, and supersonic Mach numbers over a range of unit Reynolds numbers to obtain an improved understanding of wind tunnel flow quality influence. Cone surface microphone measurements showed Tollmien-Schlichting waves present. Transition location defined by pitot probe measurements showed transition Reynolds number to be correlatable to cone surface disturbance amplitude within + or - 20 percent for the majority of tunnel and flight data.

Dougherty, N. S., Jr.↗

Low-frequency pressure fluctuations in axisymmetric turbulent boundary layers

Measurements were made of wall pressure fluctuations under a turbulent boundary layer on the fuselage of a sailplane. Experiments with the sailplane offered a noise-free flow with a low free-stream turbulence level. In this environment the wall-pressure spectrum of a turbulent boundary layer with natural transition was found to drop off at low frequencies. Correlations between several wall-mounted microphones revealed that the large-scale motions contribute about 35% to the mean square pressure. Velocity fluctuations at several positions within and outside the boundary layer were measured and correlated with the wall pressure. It seems that the irrotational motions in the turbulent region are primarily responsible for the large-scale wall-pressure fluctuations. A time-lagged conditional correlation of the pressure was introduced to gain further insight into the pressure-producing motions.

Panton, R. L.↗

QCSEE fan exhaust bulk absorber treatment evaluation

The purpose of the experimental program reported herein was to evaluate the acoustic suppression capability of bulk absorber material designed for use in the fan exhaust duct walls of the QCSEE UTW (under-the-wing) engine and to compare it with other means of acoustic suppression. The paper includes comparison of the acoustic suppression to the original design for the QCSEE UTW engine fan duct which consisted of phased SDOF (single-degree-of-freedom) wall treatment and a splitter and also with the splitter removed. The method of approach consisted of mounting the UTW engine on the test stand of the Lewis Engine Noise Facility with an appropriate array of far-field microphones in order to measure the acoustic levels of the various configurations. Peak suppression was about as predicted with the bulk absorber configuration; however, the broadband characteristics were not attained. Post-test inspection revealed surface oil contamination on the bulk material which could have caused the loss in bandwidth suppression.

Bloomer, H. E.↗