Search NASA⌕ Search

SEARCH · Search NASA

Results for “Laboratory evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Effects of dose rate on the microstructure and deuterium retention in γ-LiAlO 2 pellets

This report presents experimental findings obtained from November 2024 to September 2025. Defect accumulation and microstructural evolution during ion irradiation at elevated temperatures are governed by two competing processes: defect production, driven by dose rate, and defect recovery, controlled by defect diffusion, interaction, and annihilation. At a given dose, the resulting microstructural evolution depends on both the dose rate and irradiation temperature. As a continuation of our FY24 tritium science project, which investigated temperature effects at a fixed dose rate, this study focuses on dose-rate effects at a fixed temperature to provide deeper insights into the irradiated microstructure and compositional changes in γ-LiAlO 2 pellets. The study aims to elucidate the impact of dose rate on microstructure, precipitate morphology, deuterium retention, and lithium volatility in γ-LiAlO 2 pellets under sequential 120 keV He + and 80 keV D 2 + ion irradiation. Three dose rates of 7.3×10 4 , 2.9×10 4 and 6.8×10 5 dpa/s were applied to achieve the same total ion fluence of 2×10 17 (He + +D + )/cm 2 at 500 °C, corresponding to a maximum combined dose of 7.55 dpa at ~255 nm. The irradiated pellets were subsequently characterized using scanning transmission electron microscopy (STEM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The microstructural response of γ-LiAlO 2 to ion irradiation was found to be strongly dose-rate dependent. At medium and high dose rates, irradiation produced a surface amorphized layer and an underlying crystalline layer containing LiAl 5 O 8 precipitates, with implanted gases accumulating and forming blisters at the crystalline-amorphous interface. It remains to be investigated whether the amorphized layer was produced by He + ion irradiation prior to D 2 + ion irradiation. In contrast, at low dose rates, the material remained crystalline, with cavities, likely gas-filled, distributed around precipitates, within the γ-LiAlO 2 matrix, and along grain boundaries. While precipitate morphology exhibited anisotropy, their size showed little sensitivity to dose rate in the applied range of this study. This result, however, does not rule out the possibility that further reductions in dose rate could influence precipitate size. High dose-rate irradiation enhanced protonium–deuterium isotopic exchange and lithium depletion in the amorphized region. Collectively, the results show that dose rate governs amorphization, gas redistribution, isotopic exchange, and lithium depletion, providing important insights into the mechanisms underlying structural evolution in γ-LiAlO 2 pellets under reactor-relevant irradiation conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2017

Printing Fabrication of Bulk Heterojunction Solar Cells and In Situ Morphology Characterization

Polymer-based materials hold promise as low-cost, flexible efficient photovoltaic devices. Most laboratory efforts to achieve high performance devices have used devices prepared by spin coating, a process that is not amenable to large-scale fabrication. This mismatch in device fabrication makes it difficult to translate quantitative results obtained in the laboratory to the commercial level, making optimization difficult. Using a mini-slot die coater, this mismatch can be resolved by translating the commercial process to the laboratory and characterizing the structure formation in the active layer of the device in real time and in situ as films are coated onto a substrate. The evolution of the morphology was characterized under different conditions, allowing us to propose a mechanism by which the structures form and grow. This mini-slot die coater offers a simple, convenient, material efficient route by which the morphology in the active layer can be optimized under industrially relevant conditions. The goal of this protocol is to show experimental details of how a solar cell device is fabricated using a mini-slot die coater and technical details of running in situ structure characterization using the mini-slot die coater.

14 SOLAR ENERGY↗
NASA NTRS1979

Advanced thermoset resins for fire-resistant composites

The thermal and flammability properties of some thermoset polymers and composites are described. The processing and evaluation of composites fabricated from currently used resins and advanced fire-resistant resins are also described. Laboratory test methodology used to qualify candidate composite materials includes thermochemical characterization of the polymeric compounds and evaluation of the glass reinforced composites for flammability and smoke evolution. The use of these test methods will be discussed in comparing advanced laminating resins and composites consisting of modified epoxies, phenolics and bismaleimide, with conventional baseline materials consisting of epoxy.

Kourtides, D. A.↗
NASA NTRS1987

Turbulence as observed by concurrent measurements made at NSSL using weather radar, Doppler radar, Doppler lidar and aircraft

As air traffic increases and aircraft capability increases in range and operating altitude, the exposure to weather hazards increases. Turbulence and wind shears are two of the most important of these hazards that must be taken into account if safe flight operations are to be accomplished. Beginning in the early 1960's, Project Rough Rider began thunderstorm investigations. Past and present efforts at the National Severe Storm Laboratory (NSSL) to measure these flight safety hazards and to describe the use of Doppler radar to detect and qualify these hazards are summarized. In particular, the evolution of the Doppler-measured radial velocity spectrum width and its applicability to the problem of safe flight is presented.

Lee, Jean T.↗
NASA NTRS1990

Proceedings of the MEVTV Workshop on The Evolution of Magma Bodies on Mars

The workshop focused on many of the diverse approaches related to the evolution of magma bodies on Mars that have been pursued during the course of the Mars Evolution of Volcanism, Tectonism, and Volatiles (MEVTV) Program. Approximately 35 scientists from the Mars volcanology, petrology, geochemistry, and modeling communities attended. Segments of the meeting concentrated of laboratory analyses and investigations of SNC meteorites, the interpretation of Viking Orbiter and Lander datasets, and the interpretation of computer codes that model volcanic and tectonic processes on Mars. Abstracts of these reports are presented.

Mouginis-Mark, P.↗
NASA NTRS1993

Gasdynamics of relativistically expanding gamma-ray burst sources - Kinematics, energetics, magnetic fields, and efficiency

We calculate both analytically and numerically the evolution of highly relativistic fireballs through the stages of free expansion and coasting, and determine the dependence of the thermodynamic and radiation variables in the comoving and laboratory flames. The dynamics and the comoving geometry change at the (lab) expansion factors r/r(0) greater than eta and r/r(0) greater than eta-squared, respectively, where eta = E(0)/M(0)c-squared is the initial Lorentz factor. In the lab, the gas appears concentrated in a thin shell of width r(0) until r/r(0) of less than about eta-squared, and increases linearly after that. Magnetic fields may have been important in the original impulsive event. We discuss their effect on the fireball dynamics and also consider their effects on the radiation emitted when the fireball runs into an external medium and is decelerated. The inverse synchro-Compton mechanism can then yield high radiative efficiency in the reverse shock (and through turbulent instabilities and mixing also in the forward blast wave), producing a burst of nonthermal radiation mainly in the MeV to GeV range. The energy and duration depend on eta, the magnetic field strength, and the external density, and can match the range of properties observed in cosmic gamma-ray bursts.

Meszaros, P.↗
NASA NTRS2015

Global and Local Gravity Field Models of the Moon Using GRAIL Primary and Extended Mission Data

The Gravity Recovery and Interior Laboratory (GRAIL) mission was designed to map the structure of the lunar interior from crust to core and to advance the understanding of the Moon's thermal evolution by producing a high-quality, high-resolution map of the gravitational field of the Moon. The mission consisted of two spacecraft, which were launched in September 2011 on a Discovery-class NASA mission. Ka-band tracking between the two satellites was the single science instrument, augmented by tracking from Earth using the Deep Space Network (DSN).

Moon↗
DOE OSTI2025

Correlating Nb-SRF Surface Processing with Evolution of Surface Electronic States

The few nanometers of the surface exposed to RF field plays a major role in defining the RF performance of superconducting cavities. Over the past two decades, several pioneering surface treatment and processing methods have emerged, enabling remarkable improvements in cavity performance by simultaneously achieving high Q with increasing Eacc. These processing methods include: thermal treatment under ultra-high vacuum (UHV) conditions across lo¬¬¬¬¬¬¬w-, mid-, and high-temperature ranges and high temperature treatments under controlled N2 atmosphere. These processes also produce distinct surface oxide configurations with different valence states, thicknesses, and uniformity, as well as different oxygen concentration profiles in bulk Nb. In this work, we are trying to understand how do surface-processing methods and the resulting oxide/oxygen profiles affect the electronic structure of surface and the mechanism of superconductivity? With the help of Fermilab’s in-house X-ray photoemission facility and, in collaboration with the synchrotron-based angle-resolved photoemission (ARPES) facility at Argonne National Laboratory, we are investigating how the valence band structure and density of states (DoS) near the Fermi level modify with different surface treatments. Our observations show that different surface-processing methods lead to distinct evolutions of the valence-band states near the Fermi level during the superconducting transition. This behavior suggests variations in Nb-O orbital hybridizations and points towards the possibility of different underlying mechanisms of superconductivity governed by the surface chemistry and oxide configuration. We also correlate these distinct superconducting mechanisms with RF cavity performance, specifically focusing on measured surface resistance, the nature of the Q-slope, and quench fields observed in SRF measurements. These results will enable us to identify the potential limiting factors and relevant controllable parameters that can be further optimized to improve the performance of SRF cavities.

Tripathi, Malvika [Fermilab]↗
DOE OSTI2025

Crossing the Oxo‐Peroxo Wall for Selective Electrochemical Epoxidation

Electrochemical oxidation in water requires the formation of reactive oxygen species to be able to oxidize unsaturated hydrocarbons to epoxides, aldehydes, and ketones. These reactions, broadly classified as alternative oxidation reactions (AOR), directly compete with the prevalent oxygen evolution reaction (OER). In molecular catalysis, the Oxo-Wall dictates a transition from a stable oxo intermediate (OER active) to a meta-stable metal-oxo (OER inactive) generally occurs. In this work on heterogeneous catalysis, the same Oxo-Wall applies, however, a meta-stable oxo preferentially coordinates with lattice oxygen to form a more stable surface peroxo intermediate. A universal free energy onset of this process is identified at 3.39 eV under electrochemical activation in water and show that it is completely decoupled from the OER oxo species. Such decoupling gives rise to a new region of oxygen reactivity relevant for AOR where a selective oxidation of the unsaturated C-C bonds is predicted to occur instead of OER. A distinct AOR overpotential volcano is constructed and identify recently reported electrocatalysts, including palladium-platinum for propylene epoxidation and silver-nickel for ethylene epoxidation, along with others such as TiO 2 and CuO. Broader implications and limitations of electrochemical AOR are discussed, highlighting their potential to enable electrochemically enhanced thermal catalysis.

Electrocatalysis↗
NASA NTRS2000

Recent Advances in Interstellar Astrochemistry

This presentation will address the possibility that molecules created in the interstellar medium may play a role in the origin and evolution of life on planetary surfaces. The argument will be presented in three main parts. First, I will review the various organic and volatile compounds that are now known or suspected to exist in a variety of circumstellar and interstellar environments. This information is largely the result of the combined applications of observational infrared and radio spectroscopy, laboratory astrophysical simulations, and theoretical astrochemistry. Second, I will devote additional attention to those materials that exhibit chemical properties that are of biological interest. Finally, I will discuss the evidence, largely gathered from the laboratory study of extraterrestrial materials (meteorites and cosmic dust), that interstellar materials, including organics, can survive the transition from the dense cloud phase into forming stellar systems. Once there, some of this material can be delivered largely unaltered to planetary surfaces where it can play key roles in the origin and subsequent evolution of life. Thus, the guiding principle of this presentation will be to attempt to 'put the astro into astrobiology.'

Sandford, Scott A.↗
NASA NTRS2020

Evolution of an Atmospheric Kármán Vortex Street From High‐Resolution Satellite Winds: Guadalupe Island Case Study

Vortex streets formed in the stratocumulus‐capped wake of mountainous islands are the atmospheric analogues of the classic Kármán vortex street observed in laboratory flows past bluff bodies. The quantitative analysis of these mesoscale unsteady atmospheric flows has been hampered by the lack of satellite wind retrievals of sufficiently high spatial and temporal resolution. Taking advantage of the cutting‐edge Advanced Baseline Imager, we derived kilometer‐scale cloud‐motion winds at 5‐min frequency for a vortex street in the lee of Guadalupe Island imaged by Geostationary Operational Environmental Satellite‐16. Combined with Moderate Resolution Imaging Spectroradiometer data, the geostationary imagery also provided accurate stereo cloud‐top heights. The time series of geostationary winds, supplemented with snapshots of ocean surface winds from the Advanced Scatterometer, allowed us to capture the wake oscillations and measure vortex shedding dynamics. The retrievals revealed a markedly asymmetric vortex decay, with cyclonic eddies having larger peak vorticities than anticyclonic eddies at the same downstream location. Drawing on the vast knowledge accumulated about laboratory bluff body flows, we argue that the asymmetric island wake arises from the combined effects of Earth's rotation and Guadalupe's nonaxisymmetric shape resembling an inclined flat plate at low angle of attack. However, numerical simulations will need to establish whether or not the selective destabilization of the shallow atmospheric anticyclonic eddies is caused by the same mechanisms that destabilize the deep columnar anticyclones of laboratory flows, such as three‐dimensional vertical perturbations due to centrifugal or elliptical instabilities.

Horváth, Á.↗
DOE OSTI2025

Surrogate Model Integration with MOOSE XFEM for Creep Crack Growth

Ferritic-martensitic steels are key structural materials for advanced reactors but experience time-dependent deformation and damage under prolonged high temperature and irradiation, leading to creep-driven crack initiation and growth. High-fidelity models—crystal plasticity with irradiation mechanisms, phase-field for microstructural evolution, and continuum-damage viscoplasticity—capture the underlying physics but are too computationally intensive for broad design-space exploration and uncertainty quantification. This milestone advances a scalable alternative by integrating a microstructure-sensitive surrogate creep model into the Multiphysics Object-Oriented Simulation Environment (MOOSE) finite element framework and extending it to fracture via the extended finite element method (XFEM). The surrogate model, developed with collaborators at Sandia and Los Alamos National Laboratories, maps relevant microstructural descriptors to the viscoplastic response of HT9. We embed this surrogate within a coupled deformation-damage workflow in MOOSE/XFEM to simulate creep-driven crack initiation and propagation. Implementation enhancements include updates to the material interface, a plastic correction phase involving microstructure evolution, and fracture criteria to ensure numerical robustness and compatibility with the surrogate structure. Demonstrations on canonical creep benchmarks spanning uniaxial and multiaxial states show that the surrogate reproduces key trends of high-fidelity models while substantially reducing computational cost. The resulting capability bridges physics fidelity and performance, providing a practical path to a predictive, microstructure-aware assessment of creep and fracture in reactor materials.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Laboratory Observation of Transition from Collisional Slow to Collisionless Fast Reconnection

Temporal transition of an externally driven antiparallel asymmetric magnetic reconnection from collisional slow to collisionless fast regime is observed in a laboratory plasma for the first time. Here, this transition is initiated when the two-fluid Hall effect begins to dominate over collisional effects at the X point, characterized by the ratio of electron-ion collision mean free path to current sheet thickness exceeding unity. Prior to the transition, an enhanced reconnection electric field develops on the low-density side where electrons are heated both ohmically and by large-amplitude lower-hybrid drift waves (LHDW) before collisionality at the X-point drop significantly. These LHDWs generate anomalous resistivity accounting for 30% of the reconnection electric field. The observed time evolution is consistent with the hybrid collisionless-collisional reconnection scenario relevant to onset of asymmetric reconnection in natural plasmas.

Shi, Peiyun [Princeton Plasma Physics Laboratory (↗
NASA NTRS1989

The delineation and interpretation of the earth's gravity field

In an attempt to understand the mechanical interaction of a growing lithosphere containing fracture zones with small and large scale mantle convection, which gives rise to geoid anomalies in oceanic regions, a series of fluid dynamical experiments is in progress to investigate: (1) the influence of lithosphere structure, fluid depth and viscosity field on the onset, scale, and evolution of sublithospheric convection; (2) the role of this convection in determining the rate of growth of lithosphere, especially in light of the flattening of the lithosphere bathymetry and heat flow at late times; and (3) combining the results of both numerical and laboratory experiments to decide the dominate factors in producing geoid anomalies in oceanic regions through the thermo-mechanical interaction of the lithosphere and subjacent mantle. The clear existence of small scale convection associated with a downward propagating solidification front (i.e., the lithosphere) and a larger scale flow associated with a discontinuous upward heat flux (i.e., a fracture zone) has been shown. The flows exist simultaneously and each may have a significant role in deciding the thermal evolution of the lithosphere and in understanding the relation of shallow mantle convection to deep mantle convection. This overall process is reflected in the geoid, gravity, and topographic anomalies in the north-central Pacific. These highly correlated fields of intermediate wavelength (approx. 200 to 2000 km) show isostatic compensation by a thin lithosphere for shorter (less than or equal to approx. 500 km), but not the longer, wavelengths. The ultimate, dynamic origin of this class of anomalies is being investigated.

Marsh, Bruce D.↗
DOE OSTI2025

Microstructurally validated stable and predictable swelling in low-enriched uranium monolithic U-10Mo fuel mini-plates

Qualification of the low-enriched uranium (LEU) monolithic U-10 wt%Mo (U-10Mo) plate-type fuel system requires a demonstration of a stable and predictable fuel swelling behavior over the anticipated operating conditions of the United States high-performance research reactors (USHPRRs) selected for conversion to LEU operation. This will allow each reactor to develop appropriate safety margins that will retain fuel element lifetime coolability. Additionally, the fuel system must maintain performance attributes when fabricated at a commercial scale. The Mini-plate 1 experiment represents the first irradiation test of commercially fabricated miniaturized monolithic LEU U-10Mo fuel plates. Here, the swelling behavior within this experiment was compared against that of historical fuel developmental tests to reveal that the commercially fabricated fuel performed within the current recommended U-10Mo swelling model's predictions. Additionally, the fuel microstructural evolution was evaluated to link initial conditions to subtle variations detected in the swelling response, providing validation and confidence that the fuel system is robust.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Multiscale and Machine Learning Modeling for Process-informed Microstructure Prediction in Additively Manufactured Materials using MALAMUTE

The Advanced Materials and Manufacturing Technologies (AMMT) program under the Department of Energy Office of Nuclear Energy aims to develop and qualify additively manufactured materials for nuclear applications. One key challenge to this is the microstructural variability observed in the additively manufactured products and their impact on the properties and performance of the material in extreme environments. AMMT is using a combination of high-throughput experimental and modeling techniques to accelerate qualification. Conventionally, in-situ and ex-situ characterizations and testing are performed to correlate different aspects of the additive manufacturing process to the final product and its performance. However, adopting a trial-and-error approach to experimentally evaluate the vast range of process parameters required to capture microstructural variability is cost-prohibitive. Modeling and simulation provide a comparatively inexpensive way to understand and correlate the microstructural evolution to the processing conditions. The modeling and simulation work-packages within the AMMT program aims to use physics-based and machine learning models to develop a digital twin for additive manufacturing that can correlate the process conditions to the final product and establish a process-structure-property-performance (PSPP) correlation. The melting and subsequent solidification that occurs during the additive process is a complex phenomenon that requires multiscale multiphysics analysis. This work package focuses on understanding the role of process variabilities on the unique microstructural characteristics of additively manufactured materials. Microstructural features at the subgrain level, such as compositional micro-heterogeneity and dislocation cells, are of particular interest here since they can influence the creep properties and radiation performance. Idaho National Laboratory’s Multiphysics Object-Oriented Simulation Environment (MOOSE), specifically the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE) software, provides an ideal platform for developing the multiphysics multiscale model to explore the intricacies of the microstructural evolution during the AM processes within a single framework. Furthermore, given that such full-fidelity simulations can be computationally intensive, reduced order models are necessary to explore the PSPP space for additively manufactured materials in an efficient, reliable, and cost-effective way. This work focuses on capturing the microstructural variabilities at the subgrain level that are often missing in the part-scale models. In fiscal year 2025, we significantly advanced upon our work in the last fiscal year, in terms of the predictive capabilities of the physics-based and ML models, by adding the capabilities to capture subgrain-level micro-segregation during solidification using phase-field model and to predict the time-dependent dynamics of the AM process through the MOGPAR model. The alloy solidification model in MOOSE incorporates the thermodynamic properties and free energy relevant to 316 stainless steel. The model demonstrates the Cr and Ni segregation that occurs during solidification, including that the rate of solidification. The microstructural evolution model is connected to the process conditions via the surrogate model developed in this work. This enables predictions of the final microstructure in conjunctions with the manufacturing process. This work supports AMMT's rapid qualification goals by laying the foundation for an efficient and cost-effective model establishing the PSPP correlation for AM. The generated microstructures and predicted micro-segregation can be used by other work packages under AMMT to evaluate the properties and environmental response of the material at the mesoscale. Thus, this work helps to identify the key microstructural features at the subgrain level that are significant in property and performance predictions of additively manufactured components. This work will also provide inputs to the large-scale process variability models to reevaluate and validate assumptions and simplifications made in the part-scale models. Furthermore, through active learning this work can help identify the data need from both modeling and experimental sides for development of a robust digital twin for additive manufacturing and accelerate the AMMT's qualification efforts.

36 - MATERIALS SCIENCE↗