Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reduced Defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

From Schottky to Ohmic graphene contacts to AlGaN/GaN heterostructures: Role of the AlGaN layer microstructure

The electrical behaviour of graphene (Gr) contacts to Al{sub x}Ga{sub 1−x}N/GaN heterostructures has been investigated, focusing, in particular, on the impact of the AlGaN microstructure on the current transport at Gr/AlGaN interface. Two Al{sub 0.25}Ga{sub 0.75}N/GaN heterostructures with very different quality in terms of surface roughness and defectivity, as evaluated by atomic force microscopy (AFM) and transmission electron microscopy, were compared in this study, i.e., a uniform and defect-free sample and a sample with a high density of typical V-defects, which locally cause a reduction of the AlGaN thickness. Nanoscale resolution current voltage (I-V) measurements by an Au coated conductive AFM tip were carried out at several positions both on the bare and Gr-coated AlGaN surfaces. Rectifying contacts were found onto both bare AlGaN surfaces, but with a more inhomogeneous and lower Schottky barrier height (Φ{sub B} ≈ 0.6 eV) for AlGaN with V-defects, with respect to the case of the uniform AlGaN (Φ{sub B} ≈ 0.9 eV). Instead, very different electrical behaviours were observed in the presence of the Gr interlayer between the Au tip and AlGaN, i.e., a Schottky contact with reduced barrier height (Φ{sub B} ≈ 0.4 eV) for the uniform AlGaN and an Ohmic contact for the AlGaN with V-defects. Interestingly, excellent lateral uniformity of the local I-V characteristics was found in both cases and can be ascribed to an averaging effect of the Gr electrode over the AlGaN interfacial inhomogeneities. Due to the locally reduced AlGaN layer thickness, V defect act as preferential current paths from Gr to the 2DEG and can account for the peculiar Ohmic behaviour of Gr contacts on defective AlGaN.

36 MATERIALS SCIENCE↗

The relationship between grain boundary structure, defect mobility, and grain boundary sink efficiency

Nanocrystalline materials have received great attention due to their potential for improved functionality and have been proposed for extreme environments where the interfaces are expected to promote radiation tolerance. However, the precise role of the interfaces in modifying defect behavior is unclear. Using long-time simulations methods, we determine the mobility of defects and defect clusters at grain boundaries in Cu. We find that mobilities vary significantly with boundary structure and cluster size, with larger clusters exhibiting reduced mobility, and that interface sink efficiency depends on the kinetics of defects within the interface via the in-boundary annihilation rate of defects. Thus, sink efficiency is a strong function of defect mobility, which depends on boundary structure, a property that evolves with time. Further, defect mobility at boundaries can be slower than in the bulk, which has general implications for the properties of polycrystalline materials. Finally, we correlate defect energetics with the volumes of atomic sites at the boundary.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Self-compensation induced vacancies for significant phonon scattering in InSb

Here, phonon scattering by point defects via mass differences and strain fluctuations could effectively reduce the lattice thermal conductivity. The atomic mass difference can be maximized by introducing the vacancies thus leading to a significant phonon scattering. Usually, the vacancies are introduced by tuning the stoichiometry or forming solid solution with certain compound that contains intrinsically high concentration of vacancies. In this work, we demonstrate that vacancies can be effectively induced by the self-compensation effect via chemical doping. Indium (In) vacancies in InSb were induced by Te-doping and a substantial reduction in thermal conductivity was observed. Room temperature lattice thermal conductivity of the melted and then hot-pressed InSb (without In vacancies) is ~ 14.5 W m –1 K –1 but only ~ 3.8 W m –1 K –1 for InSb 0.96 Te 0.04 (with In vacancies), a reduction of ~ 74%. The advantage of using this strategy for phonon engineering lies in the fact that a substantial reduction in thermal conductivity can be achieved even when the dopant concentration is rather low. Since the self-compensation effect is widely observed in different compounds, it indicates that the vacancy engineering strategy used here is also applicable to a variety of other materials to effectively reduce the lattice thermal conductivity.

36 MATERIALS SCIENCE↗

Strong Valence Band Convergence to Enhance Thermoelectric Performance in PbSe with Two Chemically Independent Controls

Abstract We present an effective approach to favorably modify the electronic structure of PbSe using Ag doping coupled with SrSe or BaSe alloying. The Ag 4d states make a contribution to in the top of the heavy hole valence band and raise its energy. The Sr and Ba atoms diminish the contribution of Pb 6s 2 states and decrease the energy of the light hole valence band. This electronic structure modification increases the density‐of‐states effective mass, and strongly enhances the thermoelectric performance. Moreover, the Ag‐rich nanoscale precipitates, discordant Ag atoms, and Pb/Sr, Pb/Ba point defects in the PbSe matrix work together to reduce the lattice thermal conductivity, resulting a record high average ZT avg of around 0.86 over 400–923 K.

Luo, Zhong‐Zhen↗

Strong Valence Band Convergence to Enhance Thermoelectric Performance in PbSe with Two Chemically Independent Controls

We present an effective approach to favorably modify the electronic structure of PbSe using Ag doping coupled with SrSe or BaSe alloying. The Ag 4d states make a contribution to in the top of the heavy hole valence band and raise its energy. The Sr and Ba atoms diminish the contribution of Pb 6s2 states and decrease the energy of the light hole valence band. This electronic structure modification increases the density-of-states effective mass, and strongly enhances the thermoelectric performance. Furthermore, the Ag-rich nanoscale precipitates, discordant Ag atoms, and Pb/Sr, Pb/Ba point defects in the PbSe matrix work together to reduce the lattice thermal conductivity, resulting a record high average ZT avg of around 0.86 over 400–923 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Behavior of yttria-stabilized zirconia (YSZ) during laser direct energy deposition of an Inconel 625-YSZ cermet

Thermal barrier coatings (TBC) are regularly used today to protect and extend the service life of several superalloys which are extensively used in high temperature applications. The existing TBCs are typically between 0.1 to 0.5 mm in thickness, are deposited on metal substrates using plasma spray or electron beam vapor deposition, and can reduce temperatures at the substrate surface by up to 300 °C. For greater temperature reductions there is a need for thicker TBCs. The building of thick TBCs has to date been stymied by poor adhesion, and cracking during deposition. It has been suggested that a functionally graded approach may reduce the residual stresses which result in these defects. To date there have been few reports on the deposition of ceramic or cermet coatings using laser AM and none have reported on the phase stability of ceramic particles post-deposition. This article is a first report on the phase stability of ceramic particles following the compositional segregation of elements during deposition using a powder feed additive manufacturing process. Functionally graded (FG), thick TBCs (>3 mm) consisting of Inconel 625 (IN625) and yttria-partially stabilized zirconia (8YSZ) were deposited on an A516 steel substrate via laser direct energy deposition (LDED). Good interfaces were observed between the bond coat (BC) and first cermet layer and between the graded cermet layers. However, cermet layers deposited with 10 wt.% or more YSZ developed a thin layer of YSZ on the surface. The thin layer of YSZ greatly hindered additional deposition of new cermet layers. In cermet layers that did exhibit good interfaces, fine, re-solidified, YSZ particles were homogenously distributed within the Inconel 625 matrix. The YSZ particles exhibited a tetragonal lattice structure and were depleted of yttrium. In contrast, the thin YSZ layer formed on a cermet surface showed no yttrium depletion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improved Performance of GaInNAs Solar Cells Grown by Molecular-Beam Epitaxy Using Increased Growth Rate Instead of Surfactants

GaInNAs is potentially useful for increasing the conversion efficiency of multijunction solar cells if low photocurrents and photovoltages can be increased. Wide-depletion width devices generate significant photocurrents using an n-i-p structure grown by molecular-beam epitaxy, but these wide depletion widths are only realized in a region of parameter space that leads to rough surface morphologies. Surfactants are effective at reducing the surface roughness, but lead to increased defect densities and changes in the net acceptor or donor concentration. Here, we show that increasing the growth rate of GaInNAs solar cells leads to smooth surfaces without the use of a surfactant, even at high In compositions and substrate temperatures. No degradation in material quality is observed when increasing the growth rate from 1.5 to 3.0 {micro}m/h, but a shunt resistance does appear for the high-growth-rate samples. This shunt is attributed to increased spitting of the Ga cell, leading to an increase in the oval defect density, at the higher effusion cell temperatures used to achieve high growth rates. As with the case of Bi in GaInNAs, increased growth rates also appear to increase the net donor concentration, but it is not clear if these effects have the same cause.

14 SOLAR ENERGY↗

Thermomechanical treatment for improved neutron irradiation resistance of austenitic alloy (Fe-21Cr-32Ni)

An optimized thermomechanical treatment (TMT) applied to austenitic alloy 800H (Fe-21Cr-32Ni) had shown significant improvements in corrosion resistance and basic mechanical properties. This study examined its effect on radiation resistance by irradiating both the solution-annealed (SA) and TMT samples at 500 degrees C for 3 dpa. Microstructural characterization using transmission electron microscopy revealed that the radiation-induced Frank loops, voids, and y'-Ni3(Ti,Al) precipitates had similar sizes between the SA and TMT samples. The amounts of radiation-induced defects and more significantly y' precipitates, however, were reduced in the TMT samples. These reductions would approximately reduce by 40.9% the radiation hardening compared to the SA samples. This study indicates that optimized-TMT is an economical approach for effective overall property improvements.

99 GENERAL AND MISCELLANEOUS↗

Solute segregation and precipitation across damage rates in dual-ion–irradiated T91 steel

We report that dual-ion irradiations using 5.0 MeV defocused Fe 2+ ions and co-injected energy degraded 2.00 to 2.85 MeV He 2+ ions were conducted on a Fe9CrMo ferritic-martensitic steel T91 to 17 dpa at a damage rate range of 5 × 10 -5 dpa/s to 3 × 10 -3 dpa/s at 445°C, followed by characterization of the microstructure using conventional and scanning transmission electron microscopy. Radiation induced Ni/Si clusters and radiation induced segregation were quantified using energy dispersive X-ray spectroscopy at each condition and were compared with the same material irradiated in the BOR-60 reactor and in the as-received condition. No significant Cr segregation was found at lath boundaries after dual-ion irradiation, while Ni and Si enrichments both decreased with increasing damage rate leading to a sharp decrease in the density of Ni/Si clusters with damage rate. Increased point defect recombination at higher ion damage rates likely reduced the Ni/Si cluster density compared with BOR-60. Although the overall vacancy concentration and diffusion are enhanced by the irradiation damage rate, the lack of time for thermal diffusion and ballistic displacements of solutes are significant limiting factors for Ni/Si cluster formation. This work demonstrates the effect of irradiation damage rate on elemental segregation and clustering when using ion irradiation to simulate reactor irradiation.

36 MATERIALS SCIENCE↗

Isotope-Engineering the Thermal Conductivity of Two-Dimensional MoS 2

Isotopes represent a degree of freedom that might be exploited to tune the physical properties of materials while preserving their chemical behaviors. In this work, we demonstrate that the thermal properties of two-dimensional (2D) transition-metal dichalcogenides can be tailored through isotope engineering. Monolayer crystals of MoS 2 were synthesized with isotopically pure 100 Mo and 92 Mo by chemical vapor deposition employing isotopically enriched molybdenum oxide precursors. The in-plane thermal conductivity of the 100 MoS 2 monolayers, measured using a non-destructive, optothermal Raman technique, is found to be enhanced by ~50% compared with the MoS 2 synthesized using mixed Mo isotopes from naturally occurring molybdenum oxide. The boost of thermal conductivity in isotopically pure MoS 2 monolayers is attributed to the combined effects of reduced isotopic disorder and a reduction in defect-related scattering, consistent with observed stronger photoluminescence and longer exciton lifetime. Finally, these results shed light on the fundamentals of 2D nanoscale thermal transport important for the optimization of 2D electronic devices.

2D materials↗

Symmetric carbon tetramers forming spin qubits in hexagonal boron nitride

Abstract Point defect quantum bits in semiconductors have the potential to revolutionize sensing at atomic scales. Currently, vacancy-related defects are at the forefront of high spatial resolution and low-dimensional sensing. On the other hand, it is expected that impurity-related defect structures may give rise to new features that could further advance quantum sensing in low dimensions. Here, we study the symmetric carbon tetramer clusters in hexagonal boron nitride and propose them as spin qubits for sensing. We utilize periodic-DFT and quantum chemistry approaches to reliably and accurately predict the electronic, optical, and spin properties of the studied defect. We show that the nitrogen-centered symmetric carbon tetramer gives rise to spin state-dependent optical signals with strain-sensitive intersystem crossing rates. Furthermore, the weak hyperfine coupling of the defect to their spin environments results in a reduced electron spin resonance linewidth that can enhance sensitivity.

Chemistry↗

Symmetry-mediated quantum coherence of W 5+ spins in an oxygen-deficient double perovskite

Elucidating the factors limiting quantum coherence in real materials is essential to the development of quantum technologies. Here we report a strategic approach to determine the effect of lattice dynamics on spin coherence lifetimes using oxygen deficient double perovskites as host materials. In addition to obtaining millisecond T 1 spin-lattice lifetimes at T ~ 10 K, measurable quantum superpositions were observed up to room temperature. We determine that T 2 enhancement in Sr 2 CaWO 6-δ over previously studied Ba 2 CaWO 6-δ is caused by a dynamically-driven increase in effective site symmetry around the dominant paramagnetic site, assigned as W 5+ via electron paramagnetic resonance spectroscopy. Further, a combination of experimental and computational techniques enabled quantification of the relative strength of spin-phonon coupling of each phonon mode. This analysis demonstrates the effect of thermodynamics and site symmetry on the spin lifetimes of W 5+ paramagnetic defects, an important step in the process of reducing decoherence to produce longer-lived qubits.

36 MATERIALS SCIENCE↗

Roles of sliding-induced defects and dissociated water molecules on low friction of graphene

Sliding contact experiments and first-principles calculations were performed to elucidate the roles of structural defects and water dissociative adsorption process on the tribo-chemical mechanisms responsible for low friction of graphene. Sliding friction tests conducted in ambient air and under a dry N2 atmosphere showed that in both cases a high running-in coefficient of friction (COF) occurred initially but a low steady-state COF was reached only when the sliding was continued in air with moisture. Density functional theory (DFT) calculations indicated that the energy barrier ( E B ) for dissociative adsorption of H 2 O was significantly lower in case of reconstructed graphene with a monovacancy compared to pristine graphene. Cross-sectional transmission electron microscopy of graphene transferred to the counterface revealed a partly amorphous structure incorporating damaged graphene layers with d-spacings larger than that of the original layers. DFT calculations on the reconstructed bilayer AB graphene systems revealed an increase of d-spacing due to the chemisorption of H, O, and OH at the vacancy sites and a reduction in the interlayer binding energy ( E B ) between the bilayer graphene interfaces compared to pristine graphene. Thus, sliding induced defects facilitated dissociative adsorption of water molecules and reduced COF of graphene for sliding tests under ambient and humid environments but not under an inert atmosphere.

Science & Technology - Other Topics↗

Emergence of low-energy spin waves in superconducting electron-doped cuprates

In order to fully utilize the technological potential of unconventional superconductors, an enhanced understanding of the superconducting mechanism is necessary. In the best performing superconductors, the cuprates, superconductivity is intimately linked with magnetism, although the details of this coupling remain elusive. Here, we address this gap by studying the electron-doped cuprate Nd 1.85 Ce 0.15 CuO 4−δ that has an antiferromagnetic ground state when synthesized and only becomes superconducting after a reductive annealing process. Using neutron spectroscopy, we show that the as-grown crystal exhibits a large spin pseudogap in the magnetic fluctuation spectrum. Annealing removes defects introduced by the commonly employed synthesis method and significantly reduces the spin pseudogap. While the spin pseudogap in the annealed sample likely arises from superconductivity, in the as-grown sample it results from the absence of long-wavelength spin waves. These results reveal a direct connection between defects, magnetism, and superconductivity, offering new insight into the mechanisms underlying high-temperature superconductivity and guiding the design of improved superconducting materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of pressure cycling and compression rate on the bcc-hcp transition in an FeNi alloy

Here, we investigate the body-centered cubic (bcc) to hexagonal close-packed (hcp) phase transition in Fe-10wt. %Ni alloy, combining pressure cycling and fast compression with time-resolved synchrotron x-ray diffraction in a dynamic diamond anvil cell. Three pressure cycles were conducted with compression rates ranging from 0.1 to nearly 10 3 GPa/s. During the first cycle with the slowest compression, the observed orientations in the bcc and hcp phases are consistent with the Burgers mechanism, followed by c-axis rotation of the hcp phase consistent with {$10$ $\bar{1}2$} twinning. During the following cycles with fast compression at 10 2 –10 3 GPa/s, the hcp phase exhibits negligible c-axis rotation with a nearly constant c/a ratio of ∼1.61 up to ∼30 GPa, indicating suppression of plastic deformation (especially, twinning) due to sample confinement from the gasket. Notably, the onset pressure of the transition decreases with additional pressure cycling and faster compression, which normally leads to over-pressurization. This suggests that defects or shear induced from the pressure cycling reduces the transition kinetics even during fast compression. These insights into the deformation and transition behavior in an FeNi alloy under multiple dynamic loading cycles can offer guidance for future design of advanced structural alloys and improve our understanding of planetary core processes.

FeNi alloy↗

Identification of a cellulose synthase-associated protein required for cellulose biosynthesis

Cellulose synthase-interactive protein 1 (CSI1) was identified in a two-hybrid screen for proteins that interact with cellulose synthase (CESA) isoforms involved in primary plant cell wall synthesis. CSI1 encodes a 2,150-amino acid protein that contains 10 predicted Armadillo repeats and a C2 domain. Mutations in CSI1 cause defective cell elongation in hypocotyls and roots and reduce cellulose content. As a result, CSI1 is associated with CESA complexes, and csi1 mutants affect the distribution and movement of CESA complexes in the plasma membrane.

cell expansion↗

Crystalline quality improvement in silicon films on sapphire using recrystallization from the silicon-sapphire interface

The use of the process of solid-phase recrystallization reduces to a great extent the number of defects in the silicon layer. An amorphous layer was formed by implantation of silicon ions. The crystalline quality of the SOS structures has been assessed by the method of high-resolution double-crystal X-ray diffraction. Silicon layers with a thickness d = 1000-2500 A and a high crystalline quality have been obtained after implantation of 150-keV silicon ions with subsequent high-temperature annealing.

36 MATERIALS SCIENCE↗

Fast-Charging Li 4 Ti 5 O 12 Anode Driven by Light

Lithium-ion batteries with fast charging capabilities are crucial for widespread adoption of electric vehicles, as they will increase acceptance of the technology and reduce range anxiety for drivers. To achieve this, advanced fast charging technologies and alternative methods to enhance the slow electrochemical processes are desperately required. This study applied light-emitting diode (LED) photo-assisted fast charging to Li 4 Ti 5 O 12 (LTO), a large bandgap cubic spinel material, to enhance charging speed through electronic-structure coupling. UV LED-generated light irradiation on to the electrode interface boosted the ion diffusion and lithium cation addition by a factor of 1.3 during electrochemical lithiation, resulting in a 30% decrease in charging time under ambient conditions. Red LED light was not effective in accelerating the reaction as it does not provide sufficient energy. The first-principles calculations support the concept that UV illumination generates charges by overcoming the material’s bandgap and effectively reducing it through the introduction of additional titanium defect states.

25 ENERGY STORAGE↗