Search NASA⌕ Search

SEARCH · Search NASA

Results for “high loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

The dynamic liquid squeeze film.

Experiments were conducted during which plane circular surfaces bounding a liquid squeeze film were subjected to impulsive loads. Pressure measurements within the liquid film and the boundary motion were recorded. These experimental results were compared with theoretical analyses which predict the bonding strength of dynamic squeeze films. The data show that the fluid inertia contributes significantly to the value of the bonding strength. It was also found that, for high loading rates, the liquid squeeze film can resist tensile loads. When in tension, liquid cavitation was observed. A photographic study was conducted which indicated that the inception of cavitation is directly related to the squeeze film liquid viscosity and inversely related to the film thickness.

Riepe, R.↗

Compressor blade setting angle accuracy study, volume 1

The aerodynamic test of a small, single stage, highly loaded, axial flow transonic compressor is covered. The stage was modified by fabricating a 24 blade rotor with mis-set blades in a repeating pattern - two degrees closed from nominal, two degrees open from nominal and nominal. The unit was instrumented to determine overall performance and average blade element data. High-response, dynamic pressure probes were installed to record pressure patterns at selected points in the flowpath. Testing was conducted at speeds from 70 to 94% of design equivalent speed with a conventional casing and also with circumferential grooves over the rotor tip. Testing indicated severe performance penalties were incurred as a result of the mis-set blading. Lower flow, pressure ratio, and efficiency were observed for the stage with or without casing treatment. Periodic pressure variations were detected at every location where high response pressure sensors were located and were directly related to blading geometry.

Holman, F. F.↗

Space Shuttle Orbiter Atlantis Liquid Oxygen Prevalve Detent Roller Cracking Investigation

During routine inspections of the Space Shuttle's Main Propulsion System (MPS) Liquid Oxygen (LO2) pre-valve, the mechanism provided to maintain the valve in the open position was found cracked. The mechanism is a Vespel roller held against the valve visor by a stack of Belleville springs. The roller has been found cracked 3 times. All three instances were in the same valve in the same location. There are 6 pre-valves on each orbiter, and only one has exhibited this problem. Every-flight inspections were instituted and the rollers were found to be cracked after only one flight. Engineers at Marshall Space Flight Center, Johnson Space Center and Kennedy Space Center worked together to determine a solution. There were several possible contributors to the failure: a mis-aligned visor, an out of specification edge with a sharp radius, an out of specification tolerance stack up of a Belleville spring stack that caused un-predicted loads on the Vespel SP-21 roller, and a dimple machined into the side of the roller to indicate LO2 compatibility that created a stress riser. The detent assembly was removed and replaced with parts that were on the low-side of the tolerance stack up to eliminate the potential for high loads on the detent roller. After one flight, the roller was inspected and showed fewer signs of wear and no cracks.

Holleman, Elizabeth↗

Structural Integrity Testing Method for PRSEUS Rod-Wrap Stringer Design

NASA Langley Research Center and The Boeing Company are developing an innovative composite structural concept, called PRSEUS, for the flat center section of a future environmentally friendly hybrid wing body (HWB) aircraft. The PRSEUS (Pultruded Rod Stitched Efficient Unitized Structure) concept uses dry textile preforms for the skins, frames, and stiffener webs. The highly loaded stiffeners are made from precured unidirectional carbon/epoxy rods and dry fiber preforms. The rods are wrapped with the dry fiber preforms and a resin infusion process is used to form the rod-wrap stiffeners. The structural integrity of the rod-wrap interface is critical for maintaining the panel s high strength and bending rigidity. No standard testing method exists for testing the strength of the rod-wrap bondline. Recently, Boeing proposed a rod push-out testing method and conducted some preliminary tests using this method. This paper details an analytical study of the rod-wrap bondline. The rod-wrap interface is modeled as a cohesive zone for studying the initiation and growth of interfacial debonding during push-out testing. Based on the correlations of analysis results and Boeing s test data, the adequacy of the rod-wrap testing method is evaluated, and potential approaches for improvement of the test method are proposed.

Wang, John T.↗

Pushing the Limits: Maximizing Energy Density in Silicon Sulfide Solid‐State Batteries

Here, for the first time, we demonstrate a silicon solid-state battery (SSB) architecture that achieves >400 Wh kg −1 , approaching the theoretical limit for silicon-based SSBs. This configuration features a 99.9 wt% micro-Si, a thin sulfide solid electrolyte (SSE), and a high-loading NMC811. Key to these results is strategically selecting and evaluating the processing techniques, whether wet or dry, for the negative electrode, positive electrode and thin sheet-type SSE. Excessive lithium incorporation into the silicon host, beyond the Li 3.75 +Si phase to form a LiSi composite, is essential to match the high capacity of the positive electrode. This SSB achieves over 1000 cycles for a 2 mAh cm −2 with ≈80% capacity retention and 94% capacity retention for 3 mAh cm −2 over 500 cycles at 25 °C. Post analysis identifies the primary capacity decay mechanisms as oxidation at the NMC/SSE interface and structural disruptions within NMC. Meanwhile, the Si electrode maintains a robust solid-electrolyte interphase layer, minimizing capacity decay. This study highlights the necessity for improved NMC coatings, lattice oxygen stabilization, and a durable positive electrode-electrolyte interface to improve the long-term stability of SSBs. Strategies leading to a single-layer pouch cell SSB exceeding 400 Wh kg −1 are developed.

25 ENERGY STORAGE↗

Fracture‐Resistant and Thermally Insulating Ultrahigh‐Temperature Carbide Foams

Dense ultrahigh‐temperature ceramics (UHTCs) carbides are recognized as potential materials for thermal protection systems (TPS) owing to properties beyond existing structural materials’ capabilities. Recent advances in UHTCs have enabled the development of multiscale porous microstructures. Herein, it is highlighted that the porosity in UHTCs are no longer treated as a defect but as a functional property specifically tailored for thermal insulation. It is a promising solution to design and fabricate bulk UHTC foams via a freeze‐drying (FD) approach followed by calibrated pressureless spark plasma sintering. Herein, monolithic TaC and HfC UHTC foams and their composite show the partial solid–solution formation of (Ta, Hf)C with porosity ≥50%. TaC–HfC foam (≈80–92 N) shows an intermediate load‐bearing capability compared to monolithic TaC (≈120–135 N) and HfC (≈28–35 N) foams, with no evident cracking on the sample surface. The thermal conductivity of partial solid‐solution TaC–HfC foam increases up to fivefold compared to parent UHTC foams. In the results, solid solutions’ efficacy and pores’ unidirectionality in providing thermal insulation to TaC–HfC while maintaining its high‐load bearing capability are illustrated. In conclusion, the developed technique establishes a new paradigm shift in UHTCs, expanding their potential for TPS in extreme environments.

36 MATERIALS SCIENCE↗

Enhancing Cycling Stability of Lithium Metal Batteries by a Bifunctional Fluorinated Ether

Abstract The lifespan of lithium (Li) metal batteries (LMBs) can be greatly improved by the formation of inorganic‐rich electrode‐electrolyte interphases (EEIs) (including solid‐electrolyte interphase on anode and cathode‐electrolyte interphase on cathode). In this work, a localized high‐concentration electrolyte containing lithium bis(fluorosulfonyl)imide (LiFSI) salt, 1,2‐dimethoxyethane (DME) solvent and 1,2‐bis(1,1,2,2‐tetrafluoroethoxy)ethane (BTFEE) diluent is optimized. BTFEE is a fluorinated ether with weakly‐solvating ability for LiFSI so it also acts as a co‐solvent in this electrolyte. It can facilitate anion decomposition at electrode surfaces and promote the formation of more inorganic‐rich EEI layers. With an optimized molar ratio of LiFSI:DME:BTFEE = 1:1.15:3, LMBs with a high loading (4 mAh cm −2 ) lithium nickel manganese cobalt oxide (LiNi 0.8 Mn 0.1 Co 0.1 ) cathode can retain 80% capacity in 470 cycles when cycled in a voltage range of 2.8–4.4 V. The fundamental understanding on the functionality of BTFEE revealed in this work provides new perspectives on the design of practical high‐energy density battery systems.

25 ENERGY STORAGE↗

Impact of ethanol blending into gasoline on aromatic compound evaporation and particle emissions from a gasoline direct injection engine

This study examined the interactions of ethanol with aromatic compounds on aromatic species evolution during gasoline evaporation and the consequent impacts on particle emissions from a single-cylinder, gasoline direct injection engine. From a chemical kinetic standpoint, the dilution of the aromatic species in gasoline by ethanol blending should reduce particle emissions because aromatics are the primary species that form particles during gasoline combustion. However, increased evaporative cooling from the ethanol and ethanol's effect on when aromatics in the fuel droplet (or surface film or pool) evaporate can drive an increase in particle emissions. The objective of this study was to quantify these competing effects. The results show that a combination of ethanol's increased evaporative cooling and impact on aromatic compound vapor-liquid equilibrium can extend droplet lifetime and cause aromatics to evaporate later in the droplet evaporation process than would be the case without ethanol. When fuels were burned in a direct-injection single-cylinder engine at high speed (2500 rpm) and relatively high load, ethanol blending caused an increase in particle emissions for fuels containing a low vapor pressure aromatic. At a lower speed (1500 rpm), no statistically significant increase in particle emissions was observed, likely because more time was available for evaporation and mixing to occur. In contrast, particle emissions from a fuel blended with a high vapor pressure aromatic were either insensitive to or reduced by ethanol blending, likewise to engine operating conditions. Current models for predicting particle emissions from gasoline engines, such as particulate matter index (PMI), generally lack variables for non-linear interactions between ethanol and gasoline hydrocarbons. To identify nonlinear interactions between predictor variables that might better explain the observed particle emissions, the least absolute shrinkage and selection operator (LASSO) regularized regression approach was employed. Among the predictor variables evaluated was the Yield Sooting Index (YSI) which is as an improved measure to quantify the aromatic's chemical tendency to generate particle emissions. Following this analysis, two variables were selected based on their frequent appearance. The first was ethanol mole percent multiplied by aromatic mole percent divided by aromatic vapor pressure [(EtOH * Aro%)/Aro VP@443 K]. The second was aromatic mole percent multiplied by aromatic YSI divided by aromatic molecular weight [(Aro% * Aro YSI)/Aro MW]. The results of linear regression including only these two combined explanatory variables achieved an r 2 = 0.959, substantially improved over the PMI model (r 2 = 0.688) and provides insight into how the PMI formalism might be modified to account for non-linear oxygenate-hydrocarbon coupling.

09 BIOMASS FUELS↗

Height-tapered double cantilever beam specimen for study of rate effects on fracture toughness of composites

Loading rate effects on the mode I delamination fracture toughness of AS4/3501-6 graphite/epoxy are presently studied by means of a height-tapered double-cantilever beam specimen whose height contour is designed to furnish a slightly decreasing compliance with increasing crack length, in order to yield a stable and smooth crack propagation at high loading rates. This specimen geometry also allows much higher crack propagation velocities to be obtained with either uniform or width-tapered double cantilever beam specimens.

Yaniv, Gershon↗

Force limited vibration testing of Cassini spacecraft cosmic dust analyser

The testing of the cosmic dust analyzer for the Cassini mission using the force limited method in order to avoid overtesting and to verify the ability of the specimen design to withstand the loads during launch and cruise, is reported on. In order to implement the method, force gages, fixtures and a test controller are required and the test specimen is subjected to sine vibration, random vibration and half sine shock. The practical aspects of the use of the force limited method are described. Due to the high loads and the weak design of the structural element, a notching method is used which provides the possibility of limiting the excitation to flight expected levels.

Jahn, Heiko↗

Femoral Blood Flow and Cardiac Output During Blood Flow Restricted Leg Press Exercise

Low load blood flow restricted resistance exercise (LBFR) causes muscle hypertrophy that may be stimulated by the local ischemic environment created by the cuff pressure. However, local blood flow (BF) during such exercise is not well understood. PURPOSE: To characterize femoral artery BF and cardiac output (CO) during leg press exercise (LP) performed at a high load (HL) and low load (LL) with different levels of cuff pressure. METHODS: Eleven subjects (men/women 4/7, age 31.4+/-12.8 y, weight 68.9+/-13.2 kg, mean+/-SD) performed 3 sets of supine left LP to fatigue with 90 s of rest in 4 conditions: HL (%1-RM/cuff pressure: 80%/0); LL (20%/0); LBFR(sub DBP) (20%/1.3 x diastolic blood pressure, BP); LBFR(sub SBP) (20%/1.3 x supine systolic BP). The cuff remained inflated throughout the LBFR exercise sessions. Artery diameter, velocity time integral (VTI), and stroke volume (SV) were measured using Doppler ultrasound at rest and immediately after each set of exercise. Heart rate (HR) was monitored using a 3-lead ECG. BF was calculated as VTI x vessel cross-sectional area. CO was calculated as HR x SV. The data obtained after each set of exercise were averaged and used for analyses. Multi-level modeling was used to determine the effect of exercise condition on dependent variables. Statistical significance was set a priori at p< 0.05. RESULTS: Artery diameter did not change from baseline. BF increased (p<0.05) after exercise in each condition except LBFR(sub SBP) in the order of HL (12.73+/-1.42 cm3,mean+/-SE) > LL (9.92+/-0.82 cm3) > LBFR(sub dBP)(6.47+/-0.79 cm3) > LBFR(sub SBP) (3.51+/-0.59 cm3). Blunted exercise induced increases occurred in HR, SV, and CO after LBFR compared to HL and LL. HR increased 45% after HL and LL and 28% after LBFR (p<0.05), but SV increased (p<0.05) only after HL. Consequently, the increase (p<0.05) in CO was greater in HL and LL (approximately 3 L/min) than in LBFR (approximately 1 L/min). CONCLUSION: BF during LBFR(sub SBP) was 1/3 of that observed in LL, which supports the hypothesis that local ischemia stimulates the LBFR hypertrophic response. As the cuff did not compress the artery, the ischemia may have occurred because of the blunted rise in CO or because arterial BP cannot overcome the cuff pressure. As LBFR(sub DBP) effectively reduced BF and CO with cuff pressures less than systolic BP, future studies should investigate the hypertrophic potential of LBFR at even lower cuff pressures.

Everett, M. E.↗

Study of controlled diffusion stator blading. 1. Aerodynamic and mechanical design report

Pratt & Whitney Aircraft is conducting a test program for NASA in order to demonstrate that a controlled-diffusion stator provides low losses at high loadings and Mach numbers. The technology has shown great promise in wind tunnel tests. Details of the design of the controlled diffusion stator vanes and the multiple-circular-arc rotor blades are presented. The stage, including stator and rotor, was designed to be suitable for the first-stage of an advanced multistage, high-pressure compressor.

Canal, E.↗

In-Space Loads Analysis of SLS/Orion

The Space Launch System and Orion spacecraft experience unique load cases during upper stage flight since the Orion must deploy its solar arrays before the upper stage engine fires. The low frequency bending modes of the deployed arrays have the potential to interact with the slosh modes of the upper stage, and with the upper stage flight steady-state accelerations this can induce high loads in the array mechanisms. A time-domain transient response solution is used to evaluate the array mechanism loads, sensitivities are noted, and the final loads are determined to be within the capability of the mechanism. Section loads and accelerations are also recovered and assessed.

SLS↗

Aircraft control system

A span-loaded, highly flexible flying wing, having horizontal control surfaces mounted aft of the wing on extended beams to form local pitch-control devices. Each of five spanwise wing segments of the wing has one or more motors and photovoltaic arrays, and produces its own lift independent of the other wing segments, to minimize inter-segment loads. Wing dihedral is controlled by separately controlling the local pitch-control devices consisting of a control surface on a boom, such that inboard and outboard wing segment pitch changes relative to each other, and thus relative inboard and outboard lift is varied.

Kendall, Greg T.↗

Environmental Barrier Coatings for Turbine Engines: A Design and Performance Perspective

Ceramic thermal and environmental barrier coatings (TEBC) for SiC-based ceramics will play an increasingly important role in future gas turbine engines because of their ability to effectively protect the engine components and further raise engine temperatures. However, the coating long-term durability remains a major concern with the ever-increasing temperature, strength and stability requirements in engine high heat-flux combustion environments, especially for highly-loaded rotating turbine components. Advanced TEBC systems, including nano-composite based HfO2-aluminosilicate and rare earth silicate coatings are being developed and tested for higher temperature capable SiC/SiC ceramic matrix composite (CMC) turbine blade applications. This paper will emphasize coating composite and multilayer design approach and the resulting performance and durability in simulated engine high heat-flux, high stress and high pressure combustion environments. The advances in the environmental barrier coating development showed promise for future rotating CMC blade applications.

Zhu, Dongming↗

Active Dihedral Control System for a Torisionally Flexible Wing

A span-loaded, highly flexible flying wing, having horizontal control surfaces mounted aft of the wing on extended beams to form local pitch-control devices. Each of five spanwise wing segments of the wing has one or more motors and photovoltaic arrays, and produces its own lift independent of the other wing segments, to minimize inter-segment loads. Wing dihedral is controlled by separately controlling the local pitch-control devices consisting of a control surface on a boom, such that inboard and outboard wing segment pitch changes relative to each other, and thus relative inboard and outboard lift is varied.

Kendall, Greg T.↗

Active Dihedral Control System for a Torsionally Flexible Wing

A span-loaded, highly flexible flying wing, having horizontal control surfaces mounted aft of the wing on extended beams to form local pitch-control devices. Each of five spanwise wing segments of the wing has one or more motors and photovoltaic arrays, and produces its own lift independent of the other wing segments, to minimize inter-segment loads. Wing dihedral is controlled by separately controlling the local pitch-control devices consisting of a control surface on a boom, such that inboard and outboard wing segment pitch changes relative to each other, and thus relative inboard and outboard lift is varied.

Kendall, Greg T.↗

In-Space Loads Analysis of SLS/Orion

The Space Launch System and Orion spacecraft experience unique load cases during upper stage flight since the Orion must deploy its solar arrays before the upper stage engine fires. The low frequency bending modes of the deployed arrays have the potential to interact with the slosh modes of the upper stage. In combination with the upper stage flight steady-state accelerations this can induce high loads in the array mechanisms. A time-domain transient response solution is used to evaluate the array mechanism loads, sensitivities are noted, and the final loads are determined to be within the capability of the mechanism. Section loads and accelerations are also recovered and assessed.

SLS↗