Search NASA⌕ Search

SEARCH · Search NASA

Results for “atomic force microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Growth and characterization of homoepitaxial β-Ga 2 O 3 layers

ß-Ga 2 O 3 is a next-generation ultra-wide bandgap semiconductor (E g = 4.8 eV to 4.9 eV) that can be homoepitaxially grown on commercial substrates, enabling next-generation power electronic devices among other important applications. Analyzing the quality of deposited homoepitaxial layers used in such devices is challenging, in part due to the large probing depth in traditional x-ray diffraction (XRD) and also due to the surface-sensitive nature of atomic force microscopy (AFM). Here, a combination of evanescent grazing-incidence skew asymmetric XRD and AFM are investigated as an approach to effectively characterize the quality of homoepitaxial ß-Ga 2 O 3 layers grown by molecular beam epitaxy at a variety of Ga/O flux ratios. Accounting for both structure and morphology, optimal films are achieved at a Ga/O ratio of ~1.15, a conclusion that would not be possible to achieve by either XRD or AFM methods alone. Finally, fabricated Schottky barrier diodes with thicker homoepitaxial layers are characterized by J-V and C-V measurements, revealing an unintentional doping density of 4.3×10 16 cm -3 - 2×10 17 cm -3 in the epilayer. These results demonstrate the importance of complementary measurement methods for improving the quality of the ß-Ga 2 O 3 homoepitaxial layers used in power electronic and other devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

AFM Microcantilever With a Collocated AlN Sensor-Actuator Pair: Enabling Efficient Q-Control for Dynamic Imaging

This manuscript presents a novel microcantilever with an embedded piezoelectric sensor-actuator pair for dynamic atomic force microscopy (AFM). The transducer pair is constructed from a two-layered AlN stack. Stacking the piezoelectric transducers in this manner leads to a minimal feedthrough from actuation to sense electrode, granting a high dynamic range frequency response for dynamic mode AFM. The cantilever's design allows for dual mode operation at 1 st and 2 nd resonance modes. High resolution tapping mode imaging results are reported, while the cantilever is operated at these modes. A feedback control loop is used to modify quality factor of the 1 st mode of the cantilever, using a positive position feedback (PPF) controller. Here, a faster response time is achieved by reducing the Q-factor, enabling the cantilever to track the topography at a higher scan rate. Results of bimodal AFM imaging are reported, using amplitude changes of the 1 st mode for surface topography, while material properties are encoded in phase changes of the 2 nd mode.

47 OTHER INSTRUMENTATION↗
DOE OSTI2015

Thermal stability of an InAlN/GaN heterostructure grown on silicon by metal-organic chemical vapor deposition

The thermal stabilities of metal-organic chemical vapor deposition-grown lattice-matched InAlN/GaN/Si heterostructures have been reported by using slower and faster growth rates for the InAlN barrier layer in particular. The temperature-dependent surface and two-dimensional electron gas (2-DEG) properties of these heterostructures were investigated by means of atomic force microscopy, photoluminescence excitation spectroscopy, and electrical characterization. Even at the annealing temperature of 850 °C, the InAlN layer grown with a slower growth rate exhibited a smooth surface morphology that resulted in excellent 2-DEG properties for the InAlN/GaN heterostructure. As a result, maximum values for the drain current density (I{sub DS,max}) and transconductance (g{sub m,max}) of 1.5 A/mm and 346 mS/mm, respectively, were achieved for the high-electron-mobility transistor (HEMT) fabricated on this heterostructure. The InAlN layer grown with a faster growth rate, however, exhibited degradation of the surface morphology at an annealing temperature of 850 °C, which caused compositional in-homogeneities and impacted the 2-DEG properties of the InAlN/GaN heterostructure. Additionally, an HEMT fabricated on this heterostructure yielded lower I{sub DS,max} and g{sub m,max} values of 1 A/mm and 210 mS/mm, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Highly sensitive optical ammonia gas sensor based on Sn Doped V2O5 Nanoparticles

Highlights: • Facile synthesis of pure and Sn-doped vanadium oxide (V{sub 2}O{sub 5}) nanoparticles. • Fabrication of Optical ammonia gas sensors based on synthesized nanoparticles. • High optical sensing response (77.84%) for synthesized 2 wt% Sn doped V{sub 2}O{sub 5} nanoparticles towards ammonia gas. - Abstract: Herein, we present the synthesis, characterization and optical ammonia gas sensing of pure and Sn-doped vanadium oxide (V{sub 2}O{sub 5}) nanoparticles prepared by the sol-gel process. The V{sub 2}O{sub 5} nanoparticles were doped with Sn concentrations of 2 wt%–6 wt%, and characterized using X-ray diffraction, atomic force microscopy, UV–vis spectroscopy and photoluminescence spectroscopy which confirmed the orthorhombic crystal structure. The crystalline size was found to decrease with enhancing the doping concentrations of Sn. The lattice-strain and crystalline size with the peak-broadening of pure and Sn doped V{sub 2}O{sub 5} nanoparticles were analyzed by William-Hall (W-H) method and size-strain plot. The UV–vis absorption showed a decrease in the energy band gap (3.27 eV–3.07 eV) with an increase in the Sn doping concentration. The Sn-doped V{sub 2}O{sub 5} nanoparticles were used to detect ammonia gas (5–50 ppm) through photoluminescence based detection method. Interestingly, it was observed that the optical response for the 2 wt% Sn doped V{sub 2}O{sub 5} nanoparticles was maximum (77.84%) towards 50 ppm ammonia compared to other V{sub 2}O{sub 5}nanoparticles based samples.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2017

Vasodilator-Stimulated Phosphoprotein (VASP) depletion from breast cancer MDA-MB-231 cells inhibits tumor spheroid invasion through downregulation of Migfilin, β-catenin and urokinase-plasminogen activator (uPA)

A hallmark of cancer cells is their ability to invade surrounding tissues and form metastases. Cell-extracellular matrix (ECM)-adhesion proteins are crucial in metastasis, connecting tumor ECM with actin cytoskeleton thus enabling cells to respond to mechanical cues. Vasodilator-stimulated phosphoprotein (VASP) is an actin-polymerization regulator which interacts with cell-ECM adhesion protein Migfilin, and regulates cell migration. We compared VASP expression in MCF-7 and MDA-MB-231 breast cancer (BC) cells and found that more invasive MDA-MB-231 cells overexpress VASP. We then utilized a 3-dimensional (3D) approach to study metastasis in MDA-MB-231 cells using a system that considers mechanical forces exerted by the ECM. We prepared 3D collagen I gels of increasing concentration, imaged them by atomic force microscopy, and used them to either embed cells or tumor spheroids, in the presence or absence of VASP. We show, for the first time, that VASP silencing downregulated Migfilin, β-catenin and urokinase plasminogen activator both in 2D and 3D, suggesting a matrix-independent mechanism. Tumor spheroids lacking VASP demonstrated impaired invasion, indicating VASP’s involvement in metastasis, which was corroborated by Kaplan-Meier plotter showing high VASP expression to be associated with poor remission-free survival in lymph node-positive BC patients. Hence, VASP may be a novel BC metastasis biomarker. - Highlights: • More invasive MDA-MB-231 overexpress VASP compared to MCF-7 breast cancer cells. • We prepared 3D collagen I gels of increasing concentration and characterized them. • VASP silencing downregulated Migfilin, β-catenin and uPA both in 2D and 3D culture. • Tumor spheroids lacking VASP demonstrated impaired invasion. • Kaplan-Meier plotter shows association of high VASP expression with poor survival.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Direct measurement of storage and loss behavior in AFM force–distance experiments using the modified Fourier transformation

Force–distance curve experiments are commonly performed in atomic force microscopy (AFM) to obtain the viscoelastic characteristics of materials, such as the storage and loss moduli or compliances. The classic methods used to obtain these characteristics consist of fitting a viscoelastic material model to the experimentally obtained AFM data. Here, we demonstrate a new method that utilizes the modified discrete Fourier transform to approximate the storage and loss behavior of a material directly from the data, without the need for a fit. Additionally, one may still fit a model to the resulting storage and loss behavior if a parameterized description of the material is desired. In contrast to fitting the data to a model chosen a priori, departing from a model-free description of the material's frequency behavior guides the selection of the model, such that the user may choose the one that is most appropriate for the particular material under study. To this end, we also include modified Fourier domain descriptions of commonly used viscoelastic models.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Operando Topography and Mechanical Property Mapping of CO 2 Reduction Gas-Diffusion Electrodes Operating at High Current Densities

Electrochemical atomic force microscopy (EC-AFM) enables measurement of electrode topography and mechanical properties during electrochemical reactions. However, for aqueous-based reactions that make gas products, such as CO 2 reduction and water splitting into CO/H 2 , current densities below 1 mA cm −2 have been necessary to prevent formation of bubbles at the electrode; such bubbles can stick to the AFM probe and prevent further AFM imaging. Here, we demonstrate a novel cell design with a gas-diffusion electrode (GDE) to exhaust the gas products, thereby enabling high current density EC-AFM measurements at 1, 10, and 100 mA cm −2 that are not disturbed by bubble formation at the electrode surface. These experiments revealed a stable morphological structure of Cu catalysts deposited on GDEs during high current density operation. Systematic spatially resolved maps of deformation and adhesion showed no signs of a gas-liquid interface between catalyst particles of the GDE.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Comprehensive structural characterization of charged polymers involved in moisture-driven direct air capture

This study provides a comprehensive structural characterization of commercially available alkaline anion-exchange polymers (Fumasep FAA-3 and IRA 900) used in moisture-driven direct air capture (DAC) of carbon dioxide. Using X-ray diffraction, SAXS/WAXS, atomic force microscopy, FIB-SEM, and transmission electron microscopy, the authors identify nanoscale clustering, porosity, swelling behavior, and humidity-dependent structural changes that influence CO₂ adsorption and release. These findings establish structure–function relationships critical for designing more durable and energy-efficient DAC polymer materials.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Rechargable xLi{sub 2}MnO{sub 3}·(1 − x)Li{sub 4/3}Mn{sub 5/3}O{sub 4} electrode nanocomposite material as a modification product of chemical manganese dioxide by lithium additives

Highlights: • Li-ion battery cathode preparation procedure included MnO{sub 2} modification by Li-salts with subsequent heat treatment. • Li{sub 4}Mn{sub 5}O{sub 12}, Li{sub 2}MnO{sub 3,} and Li-rich phases form active nanocomposite cathode. • Heat treatment mode is of crucial importance for rechargeability. • Cathode material capacity is 150 mA h g{sup −1} within 2.5–4.5 V. - Abstract: Relatively simple preparation procedure of rechargeable Li-ion battery cathode material via manganese dioxide treatment with Li-containing additive and subsequent calcination has been demonstrated. X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, and atomic force microscopy study were characterisation methods of modification products. Pyrolusite, Li{sub 0.3}MnO{sub 2}, layered Li{sub 2}MnO{sub 3}, and spinel Li{sub 4}Mn{sub 5}O{sub 12} phases were revealed as products of initial ramsdellite phase transformations at temperatures of heat treatment ranging from 360 °C to 600 °C. Optimal temperature of final heat treatment from the point of view of rechargeability and discharge characteristics was 450 °C. Samples heat-treated at 450 °C are characterized by the unique combination of Li{sub 4/3}Mn{sub 5/3}O{sub 4} and Li{sub 2}MnO{sub 3} phase components due to their structural integration, a significant degree of disordering, and sizes of nanocrystallites with Li diffusion path, which is the most favourable for reversibility. The prepared nanocomposite cathode material delivers a capacity of 150 mA h g{sup −1} within 2.5–4.5 V at 0.1 mA discharge.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Ag films grown by remote plasma enhanced atomic layer deposition on different substrates

Silver (Ag) layers were deposited by remote plasma enhanced atomic layer deposition (PALD) using Ag(fod)(PEt{sub 3}) (fod = 2,2-dimethyl-6,6,7,7,8,8,8-heptafluorooctane-3,5-dionato) as precursor and hydrogen plasma on silicon substrate covered with thin films of SiO{sub 2}, TiN, Ti/TiN, Co, Ni, and W at different deposition temperatures from 70 to 200 °C. The deposited silver films were analyzed by x-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) with energy dispersive x-ray spectroscopy, four point probe measurement, ellipsometric measurement, x-ray fluorescence (XRF), and x-ray diffraction (XRD). XPS revealed pure Ag with carbon and oxygen contamination close to the detection limit after 30 s argon sputtering for depositions made at 120 and 200 °C substrate temperatures. However, an oxygen contamination was detected in the Ag film deposited at 70 °C after 12 s argon sputtering. A resistivity of 5.7 × 10{sup −6} Ω cm was obtained for approximately 97 nm Ag film on SiO{sub 2}/Si substrate. The thickness was determined from the SEM cross section on the SiO{sub 2}/Si substrate and also compared with XRF measurements. Polycrystalline cubic Ag reflections were identified from XRD for PALD Ag films deposited at 120 and 200 °C. Compared to W surface, where poor adhesion of the films was found, Co, Ni, TiN, Ti/TiN and SiO{sub 2} surfaces had better adhesion for silver films as revealed by SEM, TEM, and AFM images.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Structural and Mechanical Properties of Zr-Si-N Coatings Deposited by Arc Evaporation at Different Substrate Bias Voltages

ZrN and Zr-Si-N coatings were formed using vacuum-arc plasma fluxes deposition system at the substrate bias voltage (U{sub B}) ranged from − 50 to − 220 V on HS6-5-2 steel substrates. The structural, mechanical and tribological properties were characterized using x-ray diffraction, atomic force microscopy, scanning electron microscopy, optical microscopy, nanoindentation and ball-on-disk test. The surface roughness parameter Ra of ZrN coatings is lower than Zr-Si-N coatings. Both roughness Ra of Zr-Si-N coatings and the number of surface defects with mainly small dimensions to 1 µm decrease with increasing negative substrate bias voltage. The addition of silicon to ZrN significantly reduces the crystallite size, from about 18.3 nm for ZrN coating to 6.4 nm for Zr-Si-N coating both deposited at the same U{sub B} = − 100 V and 7.8 nm for U{sub B} = − 150 V. The hardness of Zr-Si-N coatings increases to about 30 GPa with the increase in negative substrate bias voltage (U{sub B} = − 220 V). Adhesion of the coatings tested is high, and critical load is above 80 N and reduces with U{sub B} increase. Coefficient of friction determined using AFM shows similar trend as surface roughness in microscale.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Semiconductor-insulator transition in VO{sub 2} (B) thin films grown by pulsed laser deposition

Thin films of B-phase VO{sub 2} were grown by pulsed-laser deposition on glass and (100)-cut MgO substrates in a temperature range from 375 to 425 °C and at higher gas pressures than usual for this technique. The films were strongly oriented, with ab-planes parallel to the substrate surface. Detailed study of surface morphology through Atomic Force Microscopy images suggest significant differences in evolution as a function of growth temperature for films on the two types of substrates. Measurements of electrical conductivities through cooling-heating cycles from room temperature to 120 K showed changes of five orders of magnitude, with steeper changes between room temperature and ∼150 K, which corresponds with the extended and reversible phase transition known to occur for this material. At lower temperatures conductivities exhibited Arrhenius behavior, indicating that no further structural change was occurring and that conduction is thermally activated. In this lower temperature range, conductivity of the samples can be described by the near-neighbor hopping model. No hysteresis was found between the cooling and heating braches of the cycles, which is at variance with previous results published for VO{sub 2} (B). This apparent lack of hysteresis for thin films grown in the manner described and the large conductivity variation as a function of temperature observed for the samples suggests this material could be of interest for infrared sensing applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Evolution of nano-rheological properties of Nafion{sup ®} thin films during pH modification by strong base treatment: A static and dynamic force spectroscopy study

Addition of a strong base to Nafion{sup ®} proton exchange membranes is a common practice in industry to increase their overall performance in fuel cells. Here, we investigate the evolution of the nano-rheological properties of Nafion thin films as a function of the casting pH, via characterization with static and dynamic, contact and intermittent-contact atomic force microscopy (AFM) techniques. The addition of KOH causes non-monotonic changes in the viscoelastic properties of the films, which behave as highly dissipative, softer materials near neutral pH values, and as harder, more elastic materials at extreme pH values. We quantify this behavior through calculation of the temporal evolution of the compliance and the glassy compliance under static AFM measurements. We complement these observations with dynamic AFM metrics, including dissipated power and virial (for intermittent-contact-mode measurements), and contact resonance frequency and quality factor (for dynamic contact-mode measurements). We explain the non-monotonic material property behavior in terms of the degree of ionic crosslinking and moisture content of the films, which vary with the addition of KOH. This work focuses on the special case study of the addition of strong bases, but the observed mechanical property changes are broadly related to water plasticizing effects and ionic crosslinking, which are also important in other types of films.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2019

Disentangling loosening from softening: insights into primary cell wall structure

How cell wall elasticity, plasticity, and time-dependent extension (creep) relate to one another, to plant cell wall structure and to cell growth remain unsettled topics. To examine these issues without the complexities of living tissues, in this work we treated cell-free strips of onion epidermal walls with various enzymes and other agents to assess which polysaccharides bear mechanical forces in-plane and out-of-plane of the cell wall. This information is critical for integrating concepts of wall structure, wall material properties, tissue mechanics, and mechanisms of cell growth. With atomic force microscopy we also monitored real-time changes in the wall surface during treatments. Driselase, a potent cocktail of wall-degrading enzymes, removed cellulose microfibrils in superficial lamellae sequentially, layer-by-layer, and softened the wall (reduced its mechanical stiffness), yet did not induce wall loosening (creep). In contrast Cel12A, a bifunctional xyloglucanase/cellulase, induced creep with only subtle changes in wall appearance. Both Driselase and Cel12A increased the tensile compliance, but differently for elastic and plastic components. Homogalacturonan solubilization by pectate lyase and calcium chelation greatly increased the indentation compliance without changing tensile compliances. Acidic buffer induced rapid cell wall creep via endogenous α-expansins, with negligible effects on wall compliances. We conclude that these various wall properties are not tightly coupled and thus reflect distinctive aspects of wall structure. Cross-lamellate networks of cellulose microfibrils influenced creep and tensile stiffness whereas homogalacturonan influenced indentation mechanics. This information is crucial for constructing realistic molecular models that define how wall mechanics and growth depend on primary cell wall structure.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Data supporting the manuscript "Nanometer Scale Imaging to Develop Quantitative Descriptors of Bipolar Membrane Junction Structure"

This dataset contains atomic force microscopy images associated with the manuscript "Nanometer Scale Imaging to Develop Quantitative Descriptors of Bipolar Membrane Junction Structure" by Maria Kelly, Emily R. Dunn, Ellis A. Spickermann, Josephine N. Gruber, César A. Lasalde-Ramírez, P. N. Romero Zavala, Éowyn Lucas, Ankur Gupta, Harry A. Atwater, and Wilson A. Smith. The dataset contains both raw images as well as segmented images produced by the image processing workflow described in the manuscript. A readme file and meta data file are included to provide additional details regarding the sample identity, image acquisition parameters, and file naming scheme.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Study of the Structural Properties of Silicon-on-Sapphire Layers in Hydride-Chloride Vapor-Phase Epitaxy

The surface of silicon-on-sapphire (SOS) epitaxial layers is studied by atomic-force microscopy and the UV (ultraviolet) scattering method. X-Ray diffraction analysis of the SOS layers is carried out. The silicon-sapphire transition region is studied by the photovoltage method. The problem of the accumulation of by-products formed during the synthesis of silicon from monosilane is considered and experimentally confirmed. It is found that the addition of chlorine-containing reagents to the epitaxial process makes it possible to exclude the influence exerted by these products on the growing layer and also to modify the surface microprofile. Analysis of the surface and structure of the SOS layers demonstrates that film growth occurs by the Stranski–Krastanov mechanism. It is shown that a combined method in which a 30–60-nm-thick SOS layer is preliminarily grown from pure SiH{sub 4} and then a layer is additionally grown at a 2SiH{sub 4}:1SiC1{sub 4} ratio of gas component flow rates is the most preferable method for the fabrication of SOS structures with layer thicknesses of 300 nm and more.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Computational exploration of single-protein mechanics by steered molecular dynamics

Hair cell mechanotransduction happens in tens of microseconds, involves forces of a few picoNewtons, and is mediated by nanometer-scale molecular conformational changes. As proteins involved in this process become identified and their high resolution structures become available, multiple tools are being used to explore their “single-molecule responses” to force. Optical tweezers and atomic force microscopy offer exquisite force and extension resolution, but cannot reach the high loading rates expected for high frequency auditory stimuli. Molecular dynamics (MD) simulations can reach these fast time scales, and also provide a unique view of the molecular events underlying protein mechanics, but its predictions must be experimentally verified. Thus a combination of simulations and experiments might be appropriate to study the molecular mechanics of hearing. Here I review the basics of MD simulations and the different methods used to apply force and study protein mechanics in silico. Simulations of tip link proteins are used to illustrate the advantages and limitations of this method.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Topographic and nanomechanical mapping of plutonium surfaces

Atomic force microscopy of gallium-stabilized δ-phase plutonium coupons has been used to map their topography and qualitative mechanical character, including Derjaguin-Muller-Toporov modulus, adhesion, deformation, and dissipation. Initial topographical results demonstrate that the plutonium surface is considerably rough and heterogeneous. Qualitative nanomechanical mapping revealed distinct striation patterns that are not observed in the topography images. Further investigation of the striations in the nanomechanical modes of imaging suggest that they are not measurement artifacts, or plutonium specific features. Similar investigations of stainless steel surfaces established a strong correlation between the mechanical working of the surface (i.e. cutting and grinding) and the appearance of the striations. Reimaging of the plutonium surface after moderate oxidation occurring within an inert Ar atmosphere (~1 ppm O 2 ) over the course of 13 months revealed a diminished striation pattern. It is suggested that surface stress/strain induced by the mechanical working of the metal surfaces results in the patterns of variable modulus, adhesion, deformation, and dissipation, and that these patterns are affected by the chemical changes and aging of the plutonium surface.

36 MATERIALS SCIENCE↗