SEARCH · Search NASA

Results for “enabling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Nanoscale Compositional and Strain Gradients Enable High‐Speed and Amplitude‐Resolved Pyroelectric Sensing

The frequency response of pyroelectric sensors is fundamentally governed by thermal time constant (τth, determined by thermal mass and thermal conductance) and electrical impedance arising from film capacitance and readout circuit. Conventional bulk LiTaO3 detectors are optimized for high responsivity at low modulation frequencies (0.1-10 Hz), possessing a large τth that thermally averages rapid temperature oscillations at elevated modulation frequencies, limiting fidelity in resolving dynamic varying thermal signals. Here, compositional and strain gradients are introduced into 100-nm-thick relaxor-ferroelectric films reducing τth to ≈2 µs and producing built-in potentials (≈1.45 V or 145 kV cm-1) that enhance the pyroelectric coefficient and suppress the dielectric constant. This enables complementary dual-mode operation by enhancing current-mode electrical responsivity and improving the voltage-mode figure of merit - advantageous for superior temperature resolution (ΔTmin ≈ 30 µK). The responsivity peak shifts to near 1 kHz (>2500-times higher than conventional bulk sensors), with measurable responsivity extending to a carrier frequency of 100 kHz and amplitude-resolved detection at modulation frequencies up to 15 kHz. These results establish nanoscale internal-field engineering can reshape electro-thermal trade-off in pyroelectric thin films toward zero-bias, high-thermal-sensitivity, and amplitude-resolved thermal sensing across a wide frequency bandwidth.

Lin, Ching‐Che↗

DOE OSTI2017

Controlled Selective CVD Growth of ZnO Nanowires Enabled by Mask‐Free Fabrication Approach using Aqueous Fe Catalytic Inks

Abstract Fabrication process that enables selective growth of vertically oriented zinc oxide (ZnO) nanowires (NWs) via chemical vapor deposition method and mask‐free patterning approach is reported. It is shown that synthesis of high‐quality ZnO nanowires in various architectures is achievable by optimizing the growth conditions and by precise patterning of catalytic ink precursors. Parallel direct‐write patterning method is utilized to fabricate arrays of different architectures on Si/SiO 2 substrates and directly on devices at preselected locations. The production of high‐quality, crystalline ZnO NWs is demonstrated using aqueous iron catalytic inks. The composition of the ink and the lateral size of the patterns deposited on substrates are shown to affect the resulting nanowires and thus, allowing to control the geometry (length and diameter) of the individual ZnO NWs in the patterned assemblies. The results indicate that our protocols are tailored to the fabrication of ZnO NWs with specific surface geometries and interface functionalities for variety of targeted device applications.

Alameri, Dheyaa↗

DOE OSTI2024

Autonomous Output‐Oriented Aerosol Jet Printing Enabled by Hybrid Machine Learning

Additive manufacturing (AM) is rapidly revolutionizing modern manufacturing with recent progress in advanced printing methods and improved properties of printed materials. However, traditional AM methods are limited by their input‐oriented nature, which demands tedious trial‐and‐error tuning of printing parameters to achieve desired output properties. Here, in this work, an output‐oriented artificial intelligence‐integrated AM (AIAM) method is reported that enables an user to specify desired output properties while the printer autonomously discovers the optimal input printing parameters by integrating hybrid machine learning models and in situ measurements. Based on a predictive mapping between the input printing parameters and the output properties of interests established with <20 experiments designed by active learning, inverse design tasks are performed to intelligently generate the printing parameter settings that lead to desired outcomes using reinforcement learning. This method is demonstrated by autonomous aerosol jet printing (AJP) of conductive polymer films and achieving user‐defined electrical resistances with an ultralow error of 3.7%. The AIAM method, with its output‐oriented nature, holds the potential to significantly improve the autonomy, predictability, efficiency, and accessibility of the AM processes, which will unlock new possibilities in the autonomous and intelligent printing of a broad range of functional materials and devices.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Multi‐Material Gradient Printing Using Meniscus‐enabled Projection Stereolithography (MAPS)

Light‐based additive manufacturing methods are widely used to print high‐resolution 3D structures for applications in tissue engineering, soft robotics, photonics, and microfluidics, among others. Despite this progress, multi‐material printing with these methods remains challenging due to constraints associated with hardware modifications, control systems, cross‐contamination, waste, and resin properties. Here, a new printing platform coined Meniscus‐enabled Projection Stereolithography (MAPS) is reported, a vat‐free method that relies on generating and maintaining a resin meniscus between a crosslinked structure and bottom window to print lateral, vertical, discrete, or gradient multi‐material 3D structures with no waste and user‐defined mixing between layers. MAPS is compatible with a wide range of resins shown and can print complex multi‐material 3D structures without requiring specialized hardware, software, or complex washing protocols. MAPS's ability to print structures with microscale variations in mechanical stiffness, opacity, surface energy, cell densities, and magnetic properties provides a generic method to make advanced materials for a broad range of applications.

bioprinting↗

DOE OSTI2026

Terahertz Chiral Metamaterials Enabling Broadband Polarization Conversion Using Polarization Guiding Effect

Polarization control plays a vital role in terahertz (THz) photonics, enabling a wide range of applications from imaging and spectroscopy to sensing and wireless communication. However, conventional polarization control methods at THz frequencies are limited by narrow operational bandwidths and excessive absorption losses. In this work, we present a broadband THz polarization control based on the polarization guiding effect. We design and fabricate a THz polarization rotator capable of rotating incident linear polarization by 90°. The device consists of 24 twistingly stacked silicon–air metagrating layers that introduce a large degree of form birefringence, with each metagrating layer being 280 µm thick and sequentially twisted by 3.75°. Numerical simulations using the Berreman 4 × 4 method predict broadband operation of the device. Experimental validation using THz time-domain spectroscopy confirms efficient and broadband 90° polarization rotation from 0.2 to 1.25 THz. Based on this concept, we further propose THz Q-plates for the generation of broadband structured vector beams with radial and azimuthal polarization states. This work offers a scalable, material-agnostic platform for advanced THz polarization manipulation and vector beam engineering, opening new pathways for next-generation THz photonic devices.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Tunable, Homoepitaxial Hyperbolic Metamaterials Enabled by High Mobility CdO

We report propagating light exhibits hyperbolicity in strongly anisotropic materials where the principal components of the dielectric tensor are opposite in sign. While hyperbolicity occurs naturally in anisotropic polar dielectrics, wherein optical phonons along orthogonal crystal axes are nondegenerate, such optical anisotropy can also be engineered in hyperbolic metamaterials (HMMs): thin film superlattices of alternating dielectric and metallic layers. Contrasted with the severely limited tunability of natural hyperbolic materials, the hyperbolic behavior of HMMs can be tailored significantly both through superlattice design and material selection. However, so far HMMs have suffered from high optical losses, hindering their performance. In this report, broadly tunable (λ = 2–5 µm) Type I and II hyperbolic modes with low losses (quality (Q)-factors up to 19.7) are observed through attenuated total reflectance measurements of monolithic, homoepitaxial superlattices of high- and low-doped cadmium oxide (CdO). Further, the low losses offered by CdO enable the first demonstration of real-space imaging of hyperbolic plasmon polaritons in nanoresonators by scattering-type scanning near-field optical microscopy—previously only possible for hyperbolic phonon polariton materials. Tunable, low-loss CdO HMMs promise designability for applications such as on-chip photonics, super-resolution imaging (hyperlensing), enhanced emission, novel emitter designs, and possibly quantum nanophotonic and time variant metasurfaces.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Suppressing Structural Relaxation in Nanoscale Antimony to Enable Ultralow‐Drift Phase‐Change Memory Applications

Abstract Phase‐change random‐access memory (PCRAM) devices suffer from pronounced resistance drift originating from considerable structural relaxation of phase‐change materials (PCMs), which hinders current developments of high‐capacity memory and high‐parallelism computing that both need reliable multibit programming. This work realizes that compositional simplification and geometrical miniaturization of traditional GeSbTe‐like PCMs are feasible routes to suppress relaxation. While to date, the aging mechanisms of the simplest PCM, Sb, at nanoscale, have not yet been unveiled. Here, this work demonstrates that in an optimal thickness of only 4 nm, the thin Sb film can enable a precise multilevel programming with ultralow resistance drift coefficients, in a regime of ≈10 −4 –10 −3 . This advancement is mainly owed to the slightly changed Peierls distortion in Sb and the less‐distorted octahedral‐like atomic configurations across the Sb/SiO 2 interfaces. This work highlights a new indispensable approach, interfacial regulation of nanoscale PCMs, for pursuing ultimately reliable resistance control in aggressively‐miniaturized PCRAM devices, to boost the storage and computing efficiencies substantially.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Crossbreeding Effect of Chalcogenation and Iodination on Benzene Additives Enables Optimized Morphology and 19.68% Efficiency of Organic Solar Cells

Volatile solid additives have attracted increasing attention in optimizing the morphology and improving the performance of currently dominated non-fullerene acceptor-based organic solar cells (OSCs). However, the underlying principles governing the rational design of volatile solid additives remain elusive. Herein, a series of efficient volatile solid additives are successfully developed by the crossbreeding effect of chalcogenation and iodination for optimizing the morphology and improving the photovoltaic performances of OSCs. Five benzene derivatives of 1,4-dimethoxybenzene (DOB), 1-iodo-4-methoxybenzene (OIB), 1-iodo-4-methylthiobenzene (SIB), 1,4-dimethylthiobenzene (DSB) and 1,4-diiodobenzene (DIB) are systematically studied, where the widely used DIB is used as the reference. The effect of chalcogenation and iodination on the overall property is comprehensively investigated, which indicates that the versatile functional groups provided various types of noncovalent interactions with the host materials for modulating the morphology. Among them, SIB with the combination of sulphuration and iodination enabled more appropriate interactions with the host blend, giving rise to a highly ordered molecular packing and more favorable morphology. As a result, the binary OSCs based on PM6:L8-BO and PBTz-F:L8-BO as well as the ternary OSCs based on PBTz-F:PM6:L8-BO achieved impressive high PCEs of 18.87%, 18.81% and 19.68%, respectively, which are among the highest values for OSCs.

36 MATERIALS SCIENCE↗

DOE OSTI2024

High‐Energy LiNiO 2 Li Metal Batteries Enabled by Hybrid Electrolyte Consisting of Ionic Liquid and Weakly Solvating Fluorinated Ether

Abstract In pursuit of the highest possible energy density, researchers shift their focus to the ultimate anode material, lithium metal (Li 0 ), and high‐capacity cathode materials with high nickel content (Ni > 80%). The combination of these aggressive electrodes presents unprecedented challenges to the electrolyte. Here, we report a hybrid electrolyte consisting of a highly fluorinated ionic liquid and a weakly solvating fluorinated ether, whose hybridization structure enables the reversible operation of a battery chemistry based on Li 0 and LiNiO 2 (Ni = 100%), delivering nearly theoretical capacity of the latter (up to 249 mAh g −1 ) for >300 cycles with retention of 78.6% and in absence of unwanted morphological changes in both electrodes. Extensive characterization assisted by molecular dynamic simulation and density functional theory calculations reveals the function of the fluorinated ether to be far more profound than simple dilution and viscosity reduction. Instead, it induces drastic changes in Li + ‐solvation environment, the consequence of which engenders simultaneous stabilization of electrode/electrolyte and interfacing via formation of respective interfacial chemistries. This study further unlocks fundamental knowledge underneath the prevailing “diluent strategy” that is extensively applied by the electrolyte researchers and opens more design space for the next‐generation electrolytes and interphases for these coveted battery chemistries.

25 ENERGY STORAGE↗

DOE OSTI2025

Quantitative Electron Beam‐Single Atom Interactions Enabled by Sub‐20‐pm Precision Targeting

The ability to probe and control matter at the picometer scale is essential for advancing quantum and energy technologies. Scanning transmission electron microscopy offers powerful capabilities for materials analysis and modification, but sample damage, drift, and scan distortions hinder single atom analysis and deterministic manipulation. Materials analysis and modification via electron–solid interactions can be transformed by precise delivery of electrons to a specified atomic location, maintaining the beam position despite drift, and minimizing collateral dose. Here a fast, low-dose, sub-20-pm precision electron beam positioning technique is developed, “atomic lock-on,” (ALO), which offers the ability to position the beam on a specific atomic column without previously irradiating that column. This technique is used to lock onto a single selected atomic location to repeatedly measure its weak electron energy loss signal despite sample drift. Moreover, electron beam-matter interactions in single atomic events are measured with μ s time resolution. This enables observation of single-atom dynamics, such as atomic bistability, revealing partially bonded atomic configurations and recapture phenomena. This opens prospects for using electron microscopy for high-precision measurements and deterministic control of matter for quantum technologies.

2D materials↗

DOE OSTI2016

Highly Stable Operation of Lithium Metal Batteries Enabled by the Formation of a Transient High Concentration Electrolyte Layer

Lithium (Li) metal has been extensively investigated as an anode for rechargeable battery applications due to its ultrahigh specific capacity and the lowest redox potential. However, significant challenges including dendrite growth and low Coulombic efficiency are still hindering the practical applications of rechargeable Li metal batteries. Here, we demonstrate that long-term cycling of Li metal batteries can be realized by the formation of a transient high concentration electrolyte layer near the surface of Li metal anode during high rate discharge process. The highly concentrated Li+ ions in this transient layer will immediately solvate with the available solvent molecules and facilitate the formation of a stable and flexible SEI layer composed of a poly(ethylene carbonate) framework integrated with other organic/inorganic lithium salts. This SEI layer largely suppresses the corrosion of Li metal anode by free organic solvents and enables the long-term operation of Li metal batteries. The fundamental findings in this work provide a new direction for the development and operation of Li metal batteries that could be operated at high current densities for a wide range of applications.

Environmental Molecular Sciences Laboratory↗

DOE OSTI2016

Nanowire Array Structures for Photocatalytic Energy Conversion and Utilization: A Review of Design Concepts, Assembly and Integration, and Function Enabling

The increasing human demand for clean and renewable energy and a cleaner environment has stimulated various materials related research and development for efficient solar energy conversion and utilization, photocatalytic environmental remediation, and photoassisted selective conversion of organic compounds. Among the various candidate solutions to improving the efficiency of these processes, semiconductor nanowire (NW) and nanorod (NR) array structures have been offering a unique tool box combining desirable characteristics in structure, function, and applicability. Efficient photocatalytic energy conversion requires excellent light absorption, readily charge separation, transport, and collection, as well as fast kinetics of interfacial reactions and mass transport of reactants. The long axis of the NW enables adequate light absorption, while the radical axis provides short electron–hole separation distance. Additionally, the NW arrays have relatively high surface area to facilitate interfacial kinetics while their open pore structure allows good mass transport properties. This study reviews the current status of research on NW and NR array structures of some most popular semiconducting materials for photocatalytic energy conversion and utilization including photocatalytic water splitting and CO 2 reduction/fixation, dye/quantum dot sensitized solar cells, and other photoassisted reactive applications such as pollutant degradation, selective conversion of organic compounds, and biological disinfection.

Hoang, Son↗

DOE OSTI2017

Stretchable Lithium-Ion Batteries Enabled by Device-Scaled Wavy Structure and Elastic-Sticky Separator

Fast developments and substantial achievements have been shaping the field of wearable electronic devices, resulting in the persistent requirement for stretchable lithium-ion batteries (LIBs). Despite recent progress in stretchable electrodes, stretching full batteries, including electrodes, separator, and sealing material, remains a great challenge. Here, a simple design concept for stretchable LIBs via a wavy structure at the full battery device scale is reported. All components including the package are capable of being reversibly stretched by folding the entire pouch cell into a wavy shape with polydimethylsiloxane filled in each valley region. In addition, the stretchable, sticky, and porous polyurethane/poly(vinylidene fluoride) membrane is adopted as a separator for the first time, which can maintain intimate contact between electrodes and separator to continuously secure ion pathway under dynamic state. Commercial cathode, anode, and package can be utilized in this rationally designed wavy battery to enable stretchability. The results indicate good electrochemical performances and long-term stability at repeatable release–stretch cycles. A high areal capacity of 3.6 mA h cm -2 and energy density of up to 172 W h L -1 can be achieved for the wavy battery. The promising results of the cost-effective wavy battery with high stretchability shed light on the development of stretchable energy storages.

25 ENERGY STORAGE↗

DOE OSTI2018

Chemical Immobilization and Conversion of Active Polysulfides Directly by Copper Current Collector: A New Approach to Enabling Stable Room-Temperature Li-S and Na-S Batteries

Here, room–temperature Li/Na–S batteries are promising energy storage solutions, but unfortunately suffer from serious cycling problems rooted in their polysulfide intermediates. The conventional strategy to tackle this issue is to design host materials for trapping polysulfides via weak physical confinement and interfacial chemical interactions. Even though beneficial, their capability for the polysulfide immobilization is still limited. Herein, the unique sulfiphilic nature of metallic Cu is revisited. Upon the exposure to polysulfide in aqueous or aprotic solution, the surface sulfidization rapidly takes place, resulting in the formation of Cu 2 S nanoflake arrays with tunable texture. When the sulfidized Cu current collector is directly used as the sulfur–equivalent cathode, it enables high–performance Li/Na–S batteries at room temperature with reasonable high sulfur loading. Specific capacities up to ≈1200 mAh g –1 for Li–S and ≈400 mAh g –1 for Na–S are measured when normalized to the amount of equivalent sulfur, and can be readily sustained for >1000 cycles.

25 ENERGY STORAGE↗

DOE OSTI2018

Solid-State Lithium/Selenium–Sulfur Chemistry Enabled via a Robust Solid-Electrolyte Interphase

Lithium/selenium-sulfur batteries have recently received considerable attention due to their relatively high specific capacities and high electronic conductivity. Different from the traditional encapsulation strategy for suppressing the shuttle effect, an alternative approach to directly bypass polysulfide/polyselenide formation via rational solid-electrolyte interphase (SEI) design is demonstrated here. It is found that the robust SEI layer that in situ forms during charge/discharge via interplay between rational cathode design and optimal electrolytes could enable solid-state (de)lithiation chemistry for selenium-sulfur cathodes. Hence, Se-doped S 22.2 Se/Ketjenblack cathodes can attain a high reversible capacity with minimal shuttle effects during long-term and high rate cycling. Moreover, the underlying solid-state (de)lithiation mechanism, as evidenced by in situ 7 Li NMR and in operando synchrotron X-ray probes, further extends the optimal sulfur confinement pore size to large mesopores and even macropores that have been long considered as inferior sulfur or selenium host materials, which play a crucial role in developing high volumetric energy density batteries. It is expected that the findings in this study will ignite more efforts to tailor the compositional/structure characteristics of the SEI layers and the related ionic transport across the interface by electrode structure, electrolyte solvent, and electrolyte additive screening.

(de)lithiation chemistry↗

DOE OSTI2019

“Top-Down” Li Deposition Pathway Enabled by an Asymmetric Design for Li Composite Electrode

Designing Li composite electrodes with host frameworks for accommodating Li metal has been considered to be an effective approach to suppress Li dendrites. Herein, an asymmetric design of a Mo net/Li metal film (MLF) composite electrode is developed by an inverted thermal infusion method. The asymmetric MLF electrode has a dense oxide passivated layer on the top side, a porous Mo net matrix on the back side, and active Li layer in between. The back side has a larger specific area and higher electric field than the top side, which contacts with the separator upon cycling, triggering the preferred Li deposition and stripping of the porous back side of the electrode far from the separator. The surface passivation layer on the top side of the electrode as an artificial solid electrolyte interphase ensures the stable contact with the electrolyte and separator. Meanwhile, the porous structure of the supporting Mo net provides enough space for accommodating the volume change during Li deposition and stripping. This asymmetry design enables a unique “top down” growth pathway for Li deposition in the MLF electrode, suppressing the dendrite growth effectively. In conclusion, the design strategy provides a new direction for high-energy dendrite-free Li metal anodes.

25 ENERGY STORAGE↗

DOE OSTI2020

Fast-Charging and Ultrahigh-Capacity Lithium Metal Anode Enabled by Surface Alloying

Li metal anodes are going through a great revival but they still encounter grand challenges. One often neglected issue is that most reported Li metal anodes are only cyclable under relatively low current density (<5 mA cm -2 ) and small areal capacity (<5 mAh cm -2 ), which essentially limits their high-power applications and results in ineffective Li utilization (<1%). Herein, it is reported that surface alloyed Li metal anodes can enable reversible cycling with ultrafast rate and ultralarge areal capacity. Low-cost Si wafers are used and are chemically etched down to 20-30 mu m membranes. Simply laminating a Si membrane onto Li foil results in the formation of LixSi alloy film fused onto Li metal with mechanical robustness and high Li-ion conductivity. Symmetric cell measurements show that the surface alloyed Li anode has excellent cycling stability, even under high current density up to 25 mA cm -2 and unprecedented areal capacity up to 100 mAh cm -2 . Furthermore, the surface alloyed Li anode is paired with amorphous MoS 3 cathode and achieves remarkable full-cell performance.

36 MATERIALS SCIENCE↗

DOE OSTI2020

An In Situ Formed Surface Coating Layer Enabling LiCoO 2 with Stable 4.6 V High‐Voltage Cycle Performances

Abstract The development of high‐voltage LiCoO 2 is essential for achieving lithium‐ion batteries with high volumetric energy density, however, it faces a great deal of challenges owing to the materials, structure and interfacial instability issues. In this work, a strategy is developed, through heat annealing a precoated surface layer to in situ form a high‐voltage‐stable surface coating layer, which is demonstrated to be highly effective to improve the high‐voltage performance of LiCoO 2 . It is discovered that LiCoO 2 reacts with Li 1.5 Al 0.5 Ti 1.5 (PO 4 ) 3 (LATP) at 700 °C to form exclusively spinel phases in addition to Li 3 PO 4 , which are structurally coherent to the layered lattice of LiCoO 2 . The heat annealing of the precoated thin layer of LATP enables the formation of a high‐quality surface layer. Spinel phases possess high‐voltage‐stable structures with much weaker oxidizing ability of lattice oxygen than layered structure. In addition, the Li 3 PO 4 is a good lithium‐ion conductor with excellent chemical stability at high voltages. All these benefits contribute to the construction of a uniform and conformal high‐voltage‐stable surface layer with favorable lithium conducting kinetics at the LiCoO 2 surface. The modified LiCoO 2 shows excellent 4.6 V high‐voltage cycle performance at both room temperature and 45 °C. The thermal stability is greatly enhanced as well.

Wang, Yi↗