Search NASA⌕ Search

SEARCH · Search NASA

Results for “PHASE CONTROL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Grain Boundary Complexions and Transitions in Doped Silicon (Final Technical Report)

This four-year research project has advanced the fundamental knowledge of grain boundary (GB) complexions (i.e., "two-dimensional interfacial phases") and associated GB "phase" transitions in several grounds. First, a bilayer interfacial phase, which had been directly observed by microscopy only in complex ceramic systems in prior studies, has been identified in simpler systems such as Au-doped Si and Bi-doped Ni in this study, where the interpretations of the their formation mechanisms and microscopic images are less equivocal. Second, convincing evidence for the existence of a first-order GB transition from a nominally "clean" GB to a bilayer adsorption interfacial phase has been revealed for Au-doped Si; the confirmation of the first-order nature of interfacial transitions at GBs, which was rare in prior studies, is scientifically significant and technologically important. Third, the bilayer interfacial phase discovered in Bi-doped Ni has been found to be the cause of the mysterious liquid metal embrittlement phenomenon in this system; the exact atomic level mechanism of this phenomenon has puzzled the materials and physics communities for over a century. Finally, significant advancements have been made to establish phenomenological thermodynamic models for GB complexions and transitions. Since GB complexions can control the transport, mechanical and physical properties of a broad range of metallic and ceramic materials, the fundamental knowledge generated by this project can have broad impacts on materials design in general. In this regard, understanding and controlling GB phase behaviors (complexions and transitions) can be an important component for the "Materials Genome" project.

36 MATERIALS SCIENCE↗

Structural Evolution and Transition Dynamics in Lithium Ion Battery under Fast Charging: An Operando Neutron Diffraction Investigation

Abstract Fast charging (<15 min) of lithium‐ion batteries (LIBs) for electrical vehicles (EVs) is widely seen as the key factor that will greatly stimulate the EV markets, and its realization is mainly hindered by the sluggish diffusion of Li + . To have a mechanistic understanding of Li + diffusion within LIBs, in this study, structural evolutions of electrodes for a Ni‐rich LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) || graphite cylindrical cell with high areal loading (2.78 mAh cm −2 ) are developed for operando neutron powder diffraction study at different charging rates. Via sequential Rietveld refinements, changes in structures of NMC622 and Li x C 6 are obtained during moderate and fast charging (from 0.27 C to 4.4 C). NMC622 exhibits the same structural evolution regardless of C‐rates. For phase transitions of Li x C 6 , the stage I (LiC 6 ) phase emerges earlier during the stepwise intercalation at a lower state of charge when charging rate is increased. It is also found that the stage II (LiC 12 ) → stage I (LiC 6 ) transition is the rate‐limiting step during fast charging. The LiC 12 → LiC 6 transition mechanism is further analyzed using the Johnson–Mehl–Avrami–Kolmogorov model. It is concluded as a diffusion‐controlled, 1D phase transition with decreasing nucleation kinetics under increasing chargingrates.

25 ENERGY STORAGE↗

NULLING DATA REDUCTION AND ON-SKY PERFORMANCE OF THE LARGE BINOCULAR TELESCOPE INTERFEROMETER

The Large Binocular Telescope Interferometer (LBTI) is a versatile instrument designed for high angular resolution and high-contrast infrared imaging (1.5–13 μ m). In this paper, we focus on the mid-infrared (8–13 μ m) nulling mode and present its theory of operation, data reduction, and on-sky performance as of the end of the commissioning phase in 2015 March. With an interferometric baseline of 14.4 m, the LBTI nuller is specifically tuned to resolve the habitable zone of nearby main-sequence stars, where warm exozodiacal dust emission peaks. Measuring the exozodi luminosity function of nearby main-sequence stars is a key milestone to prepare for future exo-Earth direct imaging instruments. Thanks to recent progress in wavefront control and phase stabilization, as well as in data reduction techniques, the LBTI demonstrated in 2015 February a calibrated null accuracy of 0.05% over a 3 hr long observing sequence on the bright nearby A3V star β Leo. This is equivalent to an exozodiacal disk density of 15–30 zodi for a Sun-like star located at 10 pc, depending on the adopted disk model. This result sets a new record for high-contrast mid-infrared interferometric imaging and opens a new window on the study of planetary systems.

79 ASTRONOMY AND ASTROPHYSICS↗

Lyapunov exponents and phase diagrams reveal multi-factorial control over TRAIL-induced apoptosis

Receptor-mediated apoptosis proceeds via two pathways: one requiring only a cascade of initiator and effector caspases (type I behavior) and the second requiring an initiator–effector caspase cascade and mitochondrial outer membrane permeabilization (type II behavior). Here, we investigate factors controlling type I versus II phenotypes by performing Lyapunov exponent analysis of an ODE-based model of cell death. The resulting phase diagrams predict that the ratio of XIAP to pro-caspase-3 concentrations plays a key regulatory role: type I behavior predominates when the ratio is low and type II behavior when the ratio is high. Cell-to-cell variability in phenotype is observed when the ratio is close to the type I versus II boundary. By positioning multiple tumor cell lines on the phase diagram we confirm these predictions. We also extend phase space analysis to mutations affecting the rate of caspase-3 ubiquitylation by XIAP, predicting and showing that such mutations abolish all-or-none control over activation of effector caspases. Thus, phase diagrams derived from Lyapunov exponent analysis represent a means to study multi-factorial control over a complex biochemical pathway.

59 BASIC BIOLOGICAL SCIENCES↗

Dynamically tunable second-harmonic generation using hybrid nanostructures incorporating phase-change chalcogenides

Nonlinear metasurfaces with high conversion efficiencies have been vastly investigated. However, strong dynamic tunability of such devices is limited in conventional passive plasmonic and dielectric material platforms. Germanium antimony telluride (GST) is a promising phase-change chalcogenide for the reconfiguration of metamaterials due to strong nonvolatile changes of the real and imaginary parts of the refraction index through amorphous-crystalline phase change. The orderly structured GST has an even higher potential in tunable second-harmonic generation (SHG) with a non-centrosymmetric crystal structure at the crystalline phase, while the amorphous phase of GST does not exhibit bulk second-order nonlinearity. Here, we experimentally demonstrate SHG switches by actively controlling the crystalline phase of GST for a GST-based hybrid metasurface featuring a gap-surface plasmon resonance, and a quarter-wave asymmetric Fabry–Perot (F–P) cavity incorporating GST. We obtain SHG switches with modulation depths as high as ~ 20 dB for the wavelengths at the on-state resonance. We also demonstrate the feasibility of multi-level SHG modulation by leveraging three controlled GST phases, i.e., amorphous, semi-crystalline, and crystalline, for the gap-surface plasmon hybrid device, which features stronger light–matter interaction and has higher resonant SHG efficiencies than the asymmetric F–P cavity device at respective GST phases. This research reveals that GST-based dynamic SHG switches can be potentially employed in practical applications, such as microscopy, optical communication, and photonic computing in the nonlinear regime.

42 ENGINEERING↗

Common-Mode Circulating Current Control of Paralleled Interleaved Three-Phase Two-Level Voltage-Source Converters With Discontinuous Space-Vector Modulation

This paper presents a control method to limit the common-mode (CM) circulating current between paralleled three-phase two-level voltage-source converters (VSCs) with discontinuous space-vector pulsewidth modulation (DPWM) and interleaved switching cycles. This CM circulating current can be separated into two separate components based on their frequency; the high-frequency component, close to the switching frequency, can be effectively limited by means of passive components; the low-frequency component, close to the fundamental frequency, embodies the jumping CM circulating current observed in parallel VSCs. This is the main reason why it is usually recommended not to implement discontinuous and interleaving PWM together. The origin of this low-frequency circulating current is analyzed in detail, and based on this, a method to eliminate its presence is proposed by impeding the simultaneous use of different zero vectors between the converters. This control method only requires six additional switching actions per line cycle, presenting a minimum impact on the converter thermal design. The analysis and the feasibility of the control method are verified by simulation and experimental results.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Alternative High-Performance Ceramic Waste Forms

This final report (M5NU-12-NY-AU # 0202-0410) summarizes the results of the project titled “Alternative High-Performance Ceramic Waste Forms,” funded in FY12 by the Nuclear Energy University Program (NEUP Project # 12-3809) being led by Alfred University in collaboration with Savannah River National Laboratory (SRNL). The overall focus of the project is to advance fundamental understanding of crystalline ceramic waste forms and to demonstrate their viability as alternative waste forms to borosilicate glasses. We processed single- and multiphase hollandite waste forms based on simulated waste streams compositions provided by SRNL based on the advanced fuel cycle initiative (AFCI) aqueous separation process developed in the Fuel Cycle Research and Development (FCR&D). For multiphase simulated waste forms, oxide and carbonate precursors were mixed together via ball milling with deionized water using zirconia media in a polyethylene jar for 2 h. The slurry was dried overnight and then separated from the media. The blended powders were then subjected to melting or spark plasma sintering (SPS) processes. Microstructural evolution and phase assemblages of these samples were studied using x-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersion analysis of x-rays (EDAX), wavelength dispersive spectrometry (WDS), transmission electron spectroscopy (TEM), selective area x-ray diffraction (SAXD), and electron backscatter diffraction (EBSD). These results showed that the processing methods have significant effect on the microstructure and thus the performance of these waste forms. The Ce substitution into zirconolite and pyrochlore materials was investigated using a combination of experimental (in situ XRD and x-ray absorption near edge structure (XANES)) and modeling techniques to study these single phases independently. In zirconolite materials, a transition from the 2M to the 4M polymorph was observed with increasing Ce content. The resulting powders were consolidated via SPS. Ce was reduced to the trivalent oxidation state and the zirconolite was converted into undesirable perovskite. The zirconolite polymorphs found in the synthesized powders were recovered after a post-SPS heat treatment in air. These results demonstrated the potential of processing in controlling the phase assemblage in these waste forms. Hollandites with Cr 3+ trivalent cations were identified as potential hosts for Cs immobilization and are being investigated for Cs retention properties. Series of compositions Ba 1.15-x Cs 2x Cr 2.3 Ti 5.7 O 16 , with increasing Cs loadings, were prepared by sol-gel process and characterized for structural parameters. Structural characterization was performed by a combination of powder XRD and neutron powder diffraction. Phase pure hollandite adapting monoclinic symmetry (I2/m) was observed for 0 ≤ x ≤ 0.55. These results were used to develop a new structural model to interpret Cs immobilization in these hollandites. Performance of these waste forms were evaluated for chemical durability and radiation resistance. Product consistency testing (PCT) and vapor hydration testing (VHT) were used for testing of chemical durability. Radiation resistance was tested using He + ions to simulate $\alpha$ particles and heavy ions such as Au 3+ to simulate a recoil. These results showed that these waste forms were chemically durable. The waste forms also amorphized to various degrees on exposure to simulated radiation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The influence of the secondary electron induced asymmetry on the electrical asymmetry effect in capacitively coupled plasmas

In geometrically symmetric capacitive radio-frequency plasmas driven by two consecutive harmonics, a dc self-bias can be generated as a function of the phase shift between the driving frequencies via the Electrical Asymmetry Effect (EAE). Recently, the Secondary Electron Asymmetry Effect (SEAE) was discovered (Lafleur et al., J. Phys. D: Appl. Phys. 46, 135201 (2013)): unequal secondary electron emission coefficients at both electrodes were found to induce an asymmetry in single-frequency capacitive plasmas. Here, we investigate the simultaneous presence of both effects, i.e., a dual-frequency plasma driven by two consecutive harmonics with different electrode materials. We find that the superposition of the EAE and the SEAE is generally non-linear, i.e., the asymmetries generated by each individual effect do not simply add up at all phases. The control ranges of the dc self-bias and the mean ion energy can be enlarged, if both effects are combined.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Kinetic frustration by limited bond availability controls the LAT protein condensation phase transition on membranes

LAT is a membrane-linked scaffold protein that undergoes a phase transition to form a two-dimensional protein condensate on the membrane during T cell activation. Governed by tyrosine phosphorylation, LAT recruits various proteins that ultimately enable condensation through a percolation network of discrete and selective protein-protein interactions. Here, we describe detailed kinetic measurements of the phase transition, along with coarse-grained model simulations, that reveal that LAT condensation is kinetically frustrated by the availability of bonds to form the network. Unlike typical miscibility transitions in which compact domains may coexist at equilibrium, the LAT condensates are dynamically arrested in extended states, kinetically trapped out of equilibrium. Modeling identifies the structural basis for this kinetic arrest as the formation of spindle arrangements, favored by limited multivalent binding interactions along the flexible, intrinsically disordered LAT protein. These results reveal how local factors controlling the kinetics of LAT condensation enable formation of different, stable condensates, which may ultimately coexist within the cell.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Towards Floquet Chern insulators of light

Topological photonics explores photonic systems that exhibit robustness against defects and disorder, enabled by protection from underlying topological phases. These phases are typically realized in linear optical systems and characterized by their intrinsic photonic band structures. Here we experimentally study Floquet Chern insulators in periodically driven nonlinear photonic crystals, where the topological phase is controlled by the polarization and the frequency of the driving field. Our transient sum-frequency generation measurements reveal strong hybridization of the Floquet photonic bands. The measured spectrum remains gapless under a linearly polarized drive but becomes gapped under a circularly polarized drive. Theoretical analysis confirms that the Floquet gap is topological, characterized by a non-zero Chern number—a consequence of time-reversal symmetry breaking induced by the circularly polarized driving field. Furthermore, this work offers opportunities to explore the role of classical optical nonlinearity in topological phases and their applications in nonlinear optoelectronics.

36 MATERIALS SCIENCE↗

Strain Distributions and Structural Changes in Motor Driven Gels (Final Report)

The goal of this project was to study the effects of DNA-based, force-generating motor proteins on the structure and dynamics of a DNA hydrogel. Motor proteins are nanoscale transducers, converting chemical energy embedded in the solution into local mechanical work on hydrogel strands, and thus potentially driving structural changes and/or non-equilibrium dynamics within the gel material. To explore this, we used self-assembly to create condensed DNA phases, and activated the phases with proteins. The specific aim was to study the deformations (strain fields) generated within a DNA gel by motor forces. We succeeded in this aim, developing methods to experimentally create gel/motor systems, and measure strain with high spatio-temporal resolution. A key finding was that simple continuum strain-field models fail to describe the data. A second major outcome was the development of novel models of hydrogel elasticity incorporating solvent effects that can be used to model dynamic motor-driven strains. A third major outcome was to learn how to control the phase and structure of condensed DNA particles, including both liquid-crystalline behavior, and the formation of DNA liquids.

59 BASIC BIOLOGICAL SCIENCES↗

Adaptive critic design-based reinforcement learning approach in controlling virtual inertia-based grid-connected inverters

In this report, an adaptive critic design (ACD) approach is proposed to control the phase and voltage of a grid-connected virtual synchronous generator (VSG). The penetration of fast responding inertia-less power converters significantly affect the stability of the power system, especially weak systems such as micro grids. The concept of virtual inertia addresses this concern by virtually emulating the behavior of a synchronous generator. However, the conventional VSG is designed based on two conditions: (i) fixed operating point and (ii) inductive grid connections. The performance of VSGs in low-voltage semi-resistive microgrids is far from optimal. To overcome the aforementioned concerns, a heuristic dynamic programing (HDP) approach is proposed to optimally control grid-connected VSGs. The neural-network-based inherence of the HDP enables the proposed technique to adapt to any impedance angle. The HDP controller includes two subnetworks: (i) the action network that controls the system optimally and (ii) the critic network, which evaluates the effectiveness of the action network. The simulation and experimental results are provided to evaluate the effectiveness of the proposed technique. As shown, the HDP-based approach illustrates a better performance in comparison with the conventional PI-based VSG in various operating conditions.

24 POWER TRANSMISSION AND DISTRIBUTION↗

In situ Investigation of Water Interaction with Lead-Free All Inorganic Perovskite (Cs 2 SnI x Cl 6– x )

Hybrid halide perovskites display a great tunability of optoelectronic properties and environmental stability by controlling the halogen anions (e.g., I, Cl, and Br). Yet, their water interaction and degradation mechanisms are not completely elucidated. In this work, the interaction of Cs 2 SnCl 6 and Cl-enriched solid solution Cs 2 SnI 0.9 Cl 5.1 with water was systematically studied by in situ synchrotron X-ray diffraction and micro-Raman spectra and compared with the isostructural Cs 2 SnI 6 . Unlike Cs 2 SnI 6 , which experiences a direct dissolution in water, Cs 2 SnCl 6 displays an enhanced stability and the dissolution of the Cs 2 SnCl 6 accompanies with the formation of an amorphous alteration phase. Under controlled dehydration conditions, two-dimensional Cs 2 SnCl 6 flakes can be precipitated out from water solution. Moreover, the mixed halide perovskite (Cs 2 SnI 0.9 Cl 5.1 ) experiences fast iodide dissolution in water solution and transforms to a more chloride-enriched perovskite which shows a behavior similar to Cs 2 SnCl 6 . The mechanistic understanding of the dissolution–precipitation process of Cs 2 SnI x Cl 6–x perovskites is useful for developing new perovskites with varied halogen and controlled environmental stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Oxide nucleation via threshold-driven volume instability in Ni oxidation

Oxide nucleation dictates the onset of metal oxidation, yet the atomistic pathways bridging initial oxygen adsorption to bulk phase transformation remain elusive. Here, we utilize in-situ atomic-resolution imaging to directly capture the nucleation of nickel oxide, revealing a threshold-driven, cooperative transformation of Ni into NiO. Our observations identify a distinct incubation period during which oxygen progressively accumulates in subsurface layers. Once a critical concentration and penetration depth are reached, a collective lattice reconfiguration is triggered, abruptly converting multiple Ni layers into NiO. Atomistic simulations corroborate this mechanism, identifying a cooperative lattice instability induced by subsurface oxygen saturation. These results establish subsurface oxygen incorporation as the missing mechanistic link between surface adsorption and three-dimensional oxide formation, providing an atomistic framework to understand and control reactive phase transformations in materials synthesis, catalysis, and degradation.

36 MATERIALS SCIENCE↗