Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Boreal canopy surfaces from spaceborne stereogrammetry

Surface elevation estimates from high resolution spaceborne image (HRSI) stereogrammetry are used to examine fine-scaled structure of boreal forest canopies. These data can depict detailed spatial patterns of vertical forest structure at remote sites across the circumpolar domain where these estimates would otherwise be unavailable. This work examines where these estimates are most effective at describing vertical forest structure to explain which canopy surfaces they represent. We evaluated the variation in canopy surface estimates captured from four general types of HRSI digital surface models (DSMs) across the full range of boreal canopy cover. These DSMs, classified into 4 types by grouping them according to the acquisition's (1) sun elevation angle (low or high) and (2) seasonality-driven ground surface condition (snow presence/absence), vary with acquisition characteristics and the details of this variation continues to be studied. We explored some of this variation by comparing the distributions of differences in boreal canopy percentile heights derived from reference small footprint lidar in Tanana Valley, Alaska with canopy surface elevations derived from these 4 types of HRSI DSMs. We examined how canopy surface estimates from HRSI DSMs differ according to acquisition characteristics and canopy cover, and ultimately which canopy surfaces are represented in these DSMs. Our results help clarify which boreal canopy surfaces are representative of those captured with HRSI DSMs. They show that in the Tanana Valley (1) DSMs grouped by sun elevation angle and ground surface condition provide different surface estimates of boreal canopies; (2) the two DSM types that appear to most differently capture boreal forest canopy surfaces are DSMs from snow-free images acquired at sun elevation angles <30° (Low sun elev. & snow-free) and those with snow-cover at sun elevation angles ≥30° (High sun elev. & snow-free); (3) DSMs with snow most often do not capture upper canopy surfaces; (4) the “Low sun elev. & snow-free” DSMs resolve surfaces that are most representative of upper canopy surfaces (dense forests >60% cover, 70th–80th percentile heights); and (5) in the most dense forests (>80% cover) where canopy gaps are least likely to bias downward the average surface estimates, the snow-free DSM types are representative of 70th - 80th percentile heights (“Low sun elev. & snow-free”) and 60th–70th percentile heights (“High sun elev. & snow-free”). The combination of horizontal structure (canopy cover) and acquisition characteristics affect the boreal vertical structure (canopy surface height) estimates from spaceborne stereogrammetry. These effects should be considered when analyzing products derived from HRSI DSMs, and as part of a comprehensive approach to spaceborne remote sensing of circumpolar boreal forests.

forest structure↗

Supersonic Rocket Thruster Flow Predicted by Numerical Simulation

Despite efforts in the search for alternative means of energy, combustion still remains the key source. Most propulsion systems primarily use combustion for their needed thrust. Associated with these propulsion systems are the high-velocity hot exhaust gases produced as the byproducts of combustion. These exhaust products often apply uneven high temperature and pressure over the surfaces of the appended structures exposed to them. If the applied pressure and temperature exceed the design criteria of the surfaces of these structures, they will not be able to protect the underlying structures, resulting in the failure of the vehicle mission. An understanding of the flow field associated with hot exhaust jets and the interactions of these jets with the structures in their path is critical not only from the design point of view but for the validation of the materials and manufacturing processes involved in constructing the materials from which the structures in the path of these jets are made. The hot exhaust gases often flow at supersonic speeds, and as a result, various incident and reflected shock features are present. These shock structures induce abrupt changes in the pressure and temperature distribution that need to be considered. In addition, the jet flow creates a gaseous plume that can easily be traced from large distances. To study the flow field associated with the supersonic gases induced by a rocket engine, its interaction with the surrounding surfaces, and its effects on the strength and durability of the materials exposed to it, NASA Glenn Research Center s Combustion Branch teamed with the Ceramics Branch to provide testing and analytical support. The experimental work included the full range of heat flux environments that the rocket engine can produce over a flat specimen. Chamber pressures were varied from 130 to 500 psia and oxidizer-to-fuel ratios (o/f) were varied from 1.3 to 7.5.

Davoudzadeh, Farhad↗

Solid earth science in the 1990s. Volume 1: Program plan

This is volume one of a three volume series. A plan for solid earth science research for the next decade is outlined. The following topics are addressed: scientific requirements; status of current research; major new emphasis in the 1990's; interagency and international participation; and the program implementation plan. The following fields are represented: plate motion and deformation; lithospheric structure and evolution; volcanology; land surface (processes of change); earth structure and dynamics; earth rotation and reference frames; and geopotential fields. Other topics of discussion include remote sensing, space missions, and space techniques.

Source record↗

Physical state of the western U.S. upper mantle

Using observed P wave images of the western U.S. upper mantle, which show lateral variations of up to 8%, and existing scaling relations, we infer that the low-velocity mantle is hot and partially molten to depths of 100-200 km, and that the high-velocity upper mantle is subsolidus. Most the high-velocity upper mantle within a few hundred kilometers of the coastline appears to be relatively dense, suggesting that it is relatively cool (i.e., a thermal lithosphere). This is expected for features associated with the subducting Juan de Fuca and Gorda slabs, and the high velocity upper mantle beneath the Transverse Ranges has been attributed to the sinking of negatively buoyant mantle lithosphere. Other high-velocity mantle structures near the continental margin are consistent with this interpretation. In contrast, the generally high elevations of the continental interior imply a buoyant upper mantle there, an inference that holds for both the high- and the low-velocity upper mantle. The only resonable way to produce the high-velocity low-density upper mantle is through basalt depletion, thereby creating mantle of increased solidus temperature and decreased density. We distinguish a marginal domain, within approximately 250 km of the Pacific coast, from an interior domain. This is based on the inferred upper mantle compositional difference and regional associations: beneath the marginal domain, upper mantle structures trend parallel to the surface physiography and young tectonic structures, whereas upper mantle structures beneath the continental interior trend northeasterly. This northeast orientation is discordant with the young tectonic structures, but aligns with young volcanic activity. The high lateral gradients in observed upper mantle seismic structure found throughout the western United States imply high lateral gradients in the associated temperature or partial melt fields. Because these fields diffuse on time scales of less than a few tens of millions of years, the imaged upper mantle structure is young. The following upper mantle processes are hypothesized to account for these findings and inferences. Away from the plate margin, small-scale upper mantle convection driven by partial melt-induced buoyancy of hot upper mantle leads to the production and segregation of melt and the creation of compositional variations. The heterogeneous upper mantle P wave structure of the elevated continental interior is largely a consequence of partial melt variations that are modulated by the compositional variations, and throughout this region we infer high temperatures and low densities. Near the plate margin, relative plate motions force upper mantle flow, although upper mantle flow driven by the positive buoyancy of melt and the negative bouyancy lithosphere is important locally.

Humphreys, Eugene D.↗

Rectangular Relief Diffraction Gratings for Coherent Lidar Beam Scanning

The application of specialized rectangular relief transmission gratings to coherent lidar beam scanning is presented. Two types of surface relief transmission grating approaches are studied with an eye toward potential insertion of a constant thickness, diffractive scanner where refractive wedges now exist. The first diffractive approach uses vertically oriented relief structure in the surface of an optical flat; illumination of the diffractive scanner is off-normal in nature. The second grating design case describes rectangular relief structure slanted at a prescribed angle with respect to the surface. In this case, illumination is normal to the diffractive scanner. In both cases, performance predictions for 2.0 micron, circularly polarized light at beam deflection angles of 30 or 45 degrees are presented.

Cole, H. J.↗

Composite aircraft structure having lightning protection

A lightning protection system for advanced composite aircraft structures consisting of a sandwich structure including two layers of aluminum foil separated by a layer of dielectric material. The sandwich structure is applied to the surface of the composite aircraft structure desired to be protected from lightning strike damage thereby confining damage to the sandwich structure which can be removed and replaced.

Olson, Glenn O.↗

Controlling Growth Orientation of Phthalocyanine Films by Electrical Fields

Organic Phthalocyanine films have many applications ranging from data storage to various non-linear optical devices whose quality is affected by the growth orientation of Phthalocyanine films. Due to the structural and electrical properties of Phthalocyanine molecules, the film growth orientation depends strongly on the substrate surface states. In this presentation, an electrical field up to 4000 V/cm is introduced during film growth. The Phthalocyanine films are synthesized on quartz substrates using thermal evaporation. An intermediate layer is deposited on some substrates for introducing the electrical field. Scanning electron microscopy, x-ray diffraction, and Fourier transform infrared spectroscopy are used for measuring surface morphology, film structure, and optical properties, respectively. The comparison of Phthalocyanine films grown with and without the electrical field reveals different morphology, film density, and growth orientation, which eventually change optical properties of these films. These results suggest that the growth method in the electrical field can be used to synthesized Phthalocyanine films with a preferred crystal orientation as well as propose an interaction mechanism between the substrate surface and the depositing molecules. The details of growth conditions and of the growth model of how the Phthalocyanine molecules grow in the electrical field will be discussed.

Zhu, S.↗

Surface Passivation for 3-5 Semiconductor Processing: Stable Gallium Sulphide Films by MOCVD

Gallium sulphide (GaS) has been deposited on GaAs to form stable, insulating, passivating layers. Spectrally resolved photoluminescence and surface recombination velocity measurements indicate that the GaS itself can contribute a significant fraction of the photoluminescence in GaS/GaAs structures. Determination of surface recombination velocity by photoluminescence is therefore difficult. By using C-V analysis of metal-insulator-semiconductor structures, passivation of the GaAs with GaS films is quantified.

Macinnes, Andrew N.↗

Performance of a mullite reusable surface insulation system in a hypersonic stream

The thermal and structural performance of a large panel of mullite reusable surface insulation (RSI) tiles was determined by a series of aerothermal tests in the Langley 8-foot high-temperature structures tunnel. The test panel was designed to represent a portion of the surface structure on a space shuttle orbiter fuselage along a 1,150 K isotherm with the mullite tile system bonded directly to the primary structure. Aerothermal tests were conducted at a free-stream Mach number of 6.7, a total temperature of 1,880 K, a unit Reynolds number of 4.6 million per meter, and dynamic pressure of 62 kPa. The thermal response of the mullite tile was as predicted, and the bond-line temperature did not exceed the design level of 570 K during a typical entry-heat cycle. Geometric irregularities of the tile gaps affected the tile edge temperatures when exposed to hypersonic flow. The tile coating demonstrated good toughness to particle impacts, but the coating cracked and flaked with thermal cycles. The gap filler of woven silica fibers appeared to hinder flow penetration into the gaps and withstood the flow shear of the present tests.

Hunt, L. R.↗

Piezoelectric Power Requirements for Active Vibration Control

This paper presents a method for predicting the power consumption of piezoelectric actuators utilized for active vibration control. Analytical developments and experimental tests show that the maximum power required to control a structure using surface-bonded piezoelectric actuators is independent of the dynamics between the piezoelectric actuator and the host structure. The results demonstrate that for a perfectly-controlled system, the power consumption is a function of the quantity and type of piezoelectric actuators and the voltage and frequency of the control law output signal. Furthermore, as control effectiveness decreases, the power consumption of the piezoelectric actuators decreases. In addition, experimental results revealed a non-linear behavior in the material properties of piezoelectric actuators. The material non- linearity displayed a significant increase in capacitance with an increase in excitation voltage. Tests show that if the non-linearity of the capacitance was accounted for, a conservative estimate of the power can easily be determined.

Brennan, Matthew C.↗

Method and Apparatus for the Portable Identification of Material Thickness and Defects Using Spatially Controlled Heat Application

A method and a portable apparatus for the nondestructive identification of defects in structures. The apparatus comprises a heat source and a thermal imager that move at a constant speed past a test surface of a structure. The thermal imager is off set at a predetermined distance from the heat source. The heat source induces a constant surface temperature. The imager follows the heat source and produces a video image of the thermal characteristics of the test surface. Material defects produce deviations from the constant surface temperature that move at the inverse of the constant speed. Thermal noise produces deviations that move at random speed. Computer averaging of the digitized thermal image data with respect to the constant speed minimizes noise and improves the signal of valid defects. The motion of thermographic equipment coupled with the high signal to noise ratio render it suitable for portable, on site analysis.

Cramer, K. Elliott↗

Application of Laser Based Ultrasound for NDE of Damage in Thick Stitched Composites

As design engineers implement new composite systems such as thick, load bearing composite structures, they must have certifiable confidence in structure s durability and worthiness. This confidence builds from understanding the structural response and failure characteristics of simple components loaded in testing machines to tests on full scale sections. Nondestructive evaluation is an important element which can provide quantitative information on the damage initiation, propagation, and final failure modes for the composite structural components. Although ultrasound is generally accepted as a test method, the use of conventional ultrasound for in-situ monitoring of damage during tests of large structures is not practical. The use of lasers to both generate and detect ultrasound extends the application of ultrasound to in- situ sensing of damage in a deformed structure remotely and in a non-contact manner. The goal of the present research is to utilize this technology to monitor damage progression during testing. The present paper describes the application of laser based ultrasound to quantify damage in thick stitched composite structural elements to demonstrate the method. This method involves using a Q-switched laser to generate a rapid, local linear thermal strain on the surface of the structure. This local strain causes the generation of ultrasonic waves into the material. A second laser used with a Fabry-Perot interferometer detects the surface deflections. The use of fiber optics provides for eye safety and a convenient method of delivering the laser over long distances to the specimens. The material for these structural elements is composed of several stacks of composite material assembled together by stitching through the laminate thickness that ranging from 0.5 to 0.8 inches. The specimens used for these nondestructive evaluation studies had either impact damage or skin/stiffener interlaminar failure. Although little or no visible surface damage existed, internal damage was detected by laser based ultrasound.

Anastasi, Robert F.↗

Electrostatic Properties of PE and PTFE Subjected to Atmospheric Pressure Plasma Treatment; Correlation of Experimental Results with Atomistic Modeling

The use of an atmospheric pressure glow discharge (APGD) plasma was used at KSC to increase the hydrophilicity of spaceport materials to enhance their surface charge dissipation and prevent possible ESD in spaceport operations. Significant decreases in charge decay times were observed after tribocharging the materials using the standard KSC tribocharging test. The polarity and amount of charge transferred was dependent upon the effective work function differences between the respective materials. In this study, polyethylene (PE) and polytetrafluoroethylene (PTFE) were exposed to a He+O2 APGD. The pre and post treatment surface chemistry was analyzed by X-ray photoelectron spectroscopy and contact angle measurements. Semi-empirical and ab initio calculations were performed to correlate the experimental results with some plausible molecular and electronic structure features of the oxidation process. For the PE, significant surface oxidation was observed, as indicated by XPS showing C-O, C=O, and O-C=O bonding, and a decrease in the surface contact angle from 98.9 deg to 61.2 deg. For the PTFE, no C-O bonding appeared and the surface contact angle increased indicating the APGD only succeeded in cleaning the PTFE surface without affecting the surface structure. The calculations using the PM3 and DFT methods were performed on single and multiple oligomers to simulate a wide variety of oxidation scenarios. Calculated work function results suggest that regardless of oxidation mechanism, e.g. -OH, =0 or a combination thereof, the experimentally observed levels of surface oxidation are unlikely to lead to a significant change in the electronic structure of PE and that its increased hydrophilic properties are the primary reason for the observed changes in its electrostatic behavior. The calculations for PTFE argue strongly against significant oxidation of that material, as confirmed by the XPS results.

Trigwell, Steve↗

Curved Displacement Transfer Functions for Geometric Nonlinear Large Deformation Structure Shape Predictions

For shape predictions of structures under large geometrically nonlinear deformations, Curved Displacement Transfer Functions were formulated based on a curved displacement, traced by a material point from the undeformed position to deformed position. The embedded beam (depth-wise cross section of a structure along a surface strain-sensing line) was discretized into multiple small domains, with domain junctures matching the strain-sensing stations. Thus, the surface strain distribution could be described with a piecewise linear or a piecewise nonlinear function. The discretization approach enabled piecewise integrations of the embedded-beam curvature equations to yield the Curved Displacement Transfer Functions, expressed in terms of embedded beam geometrical parameters and surface strains. By entering the surface strain data into the Displacement Transfer Functions, deflections along each embedded beam can be calculated at multiple points for mapping the overall structural deformed shapes. Finite-element linear and nonlinear analyses of a tapered cantilever tubular beam were performed to generate linear and nonlinear surface strains and the associated deflections to be used for validation. The shape prediction accuracies were then determined by comparing the theoretical deflections with the finiteelement- generated deflections. The results show that the newly developed Curved Displacement Transfer Functions are very accurate for shape predictions of structures under large geometrically nonlinear deformations.

displacement theory↗

Space Shuttle Atmospheric ascent flight dynamics

The atmospheric ascent flight phase of the mated composite booster and orbiter is discussed. The composite recoverable space shuttle booster and orbiter exhibits unique flight control characteristics. This uniqueness results from large lifting surfaces and aerodynamic and structural assymetrics. An effective load relief technique reduces aerodynamic loads on both the booster and the orbiter. Reducing aerodynamic loads permits decreasing the structural weight of the lifting and stabilizing surfaces. An orbiter payload penalty is caused by trajectory deviations resulting from load relief. However, the net effect of an effective load relief technique is an increase in payload capability. Atmospheric launch dynamics investigations have been carried out for different configuration types, which include expendable, straight wing, delta wing, and ballistic recoverable boosters.

Patha, J. T.↗

Simulations of Multidimensional Burner-stabilized Flames

Detailed numerical simulations have been performed to study the structure and dynamics of downward propagating burner-stabilized flames in lean hydrogen-air mixtures. These simulations include the effects of fluid convection, detailed hydrogen-oxygen chemistry, multispecies diffusion, thermal conduction, viscosity, and heat losses to the burner. One-dimensional calculations have been carried out to investigate burner boundary conditions. Well known features of a burner-stabilized flame have been reproduced. Two-dimensional calculations show the presence of cellular structures at the burner surface. At low inlet velocities, these cellular structures are suppressed by the increased heat loss to the burner. These simulations have been examined in detail to gain understanding of the similarities and differences in structure and stability of freely propagating and burner-stabilized flames.

Patnaik, G.↗

Clean Assembly of Genesis Collector Canister for Flight: Lessons for Planetary Sample Return

Measurement of solar composition in the Genesis collectors requires not only high sensitivity but very low blanks; thus, very strict collector contamination minimization was required beginning with mission planning and continuing through hardware design, fabrication, assembly and testing. Genesis started with clean collectors and kept them clean inside of a canister. The mounting hardware and container for the clean collectors were designed to be cleanable, with access to all surfaces for cleaning. Major structural components were made of aluminum and cleaned with megasonically energized ultrapure water (UPW). The UPW purity was >18 M resistivity. Although aluminum is relatively difficult to clean, the Genesis protocol achieved level 25 and level 50 cleanliness on large structural parts; however, the experience suggests that surface treatments may be helpful on future missions. All cleaning was performed in an ISO Class 4 (Class 10) cleanroom immediately adjacent to an ISO Class 4 assembly room; thus, no plastic packaging was required for transport. Persons assembling the canister were totally enclosed in cleanroom suits with face shield and HEPA filter exhaust from suit. Interior canister materials, including fasteners, were installed, untouched by gloves, using tweezers and other stainless steel tools. Sealants/lubricants were not exposed inside the canister, but vented to the exterior and applied in extremely small amounts using special tools. The canister was closed in ISO Class 4, not to be opened until on station at Earth-Sun L1. Throughout the cleaning and assembly, coupons of reference materials that were cleaned at the same time as the flight hardware were archived for future reference and blanks. Likewise reference collectors were archived. Post-mission analysis of collectors has made use of these archived reference materials.

Allton, J. H.↗