Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode utilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Catalytic and electrocatalytic performance of Sr(Ti 0.3 Fe 0.7 Ru 0.07 )O 3-δ for applications in solid oxide fuel cells supplied with ethanol steam reforming mixtures

We discuss how direct utilization of alcohols in Solid Oxide Fuel Cells (SOFCs) can improve the conversion efficiency by using excess heat for internal reforming and simplify the system balance of plant. Thanks to their scarce carbon- formation tendency, perovskite oxide anodes are promising alternatives to Ni-based cermets. Here we show that Sr(Ti 0.3 Fe 0.7 Ru 0.07 )O 3-δ (STF-Ru) exsolution anodes provide both catalytic reforming activity and electro- chemical activity with steam/ethanol (S/E) mixtures at 3:1 and 2:1 M ratio between 700 and 800 °C. Electrolyte- supported scandia stabilized zirconia SOFCs with STF-Ru anodes and Sr 0.95 Ti 0.3 Fe 0.7 O 3-δ (STF) cathodes are reasonably stable in the 3:1 S/E mixture over 20 h at 800 °C, with maximum power density of 195 mW/cm 2 and 140 mW/cm 2 at 0.7 V. Deactivation instead occurs with the 2:1 S/E mixture. Comparatively, cells with Ni-YSZ anodes rapidly coke and fail under the same conditions. Ethanol steam reforming experiments in a fixed bed powder reactor reveal that, above 650 °C, gas phase reactions convert ethanol to CO, hydrogen, acetaldehyde and ethylene, while STF-Ru catalyzes steam reforming. Thermogravimetric and Raman characterizations show that a moderate amount of carbon is deposited on the STF-Ru surface, which is more amorphous than the disruptive carbon which degrades Ni-YSZ.

09 BIOMASS FUELS↗

Achieving 5,000-h and 8,000-h Low-PGM Electrode Durability on Automotive Drive Cycles

Whereas total Pt loading in anode and cathode catalysts below 0.125 mg cm −2 is required to meet the stringent cost target for automotive fuel cell systems (FCS) for light duty vehicles, low-loaded cathode catalysts are susceptible to unacceptable aging-related performance losses at high current densities. A framework model, validated by accelerated stress test data, has identified cell voltage, relative humidity (RH) and temperature as the key operating variables that affect degradation of a high-activity d-PtCo/C cathode catalyst with 0.1 mg cm −2 Pt loading. Drive cycle simulations indicate that these can be controlled by properly selecting the minimum FCS power, compressor-expander module (CEM) turndown, and stack coolant temperature. The optimum system parameters are 4-kW e minimum power for an 80-kW e FCS, CEM turndown of 12.5, and 66 °C average coolant exit temperature that combine to limit the maximum cell voltage to 850 mV and outlet RH to 90%–100%. Depending on Pt loading, the mismatch between actual and allowable degradation for 10% power loss over 5,000-h lifetime requires the stack to be oversized by 2.4%–5%, resulting in 8.4%–41% lower Pt utilization and 7.1%–20.5% penalty in stack cost. The corresponding results for 8,000-h lifetime are 10.3%-14% stack oversizing, 23%–51.8% lower Pt utilization, and 24.1%–35.4% stack cost penalty.

08 HYDROGEN↗

3D–Integrated, Multi–Functional Carbon Fibers for Stable, High–Areal–Capacity Batteries

Increasing lithium-ion batteries' (LIBs) electrode areal capacity can boost energy density and lower manufacturing costs, but faces challenges in manufacturing, rate performance, and cycling stability. A conductive framework made of commercial micro-sized carbon fibers (Cfs) is presented that serves as a host for both the LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC 532) cathode and Cfs anode. The Cf framework has multiple functions that offer high electronic conductivity (270 mS cm –1 ), low tortuosity (1.7), low Li + diffusion resistance (22 Ω), and high thermal conductivity (200 W mK –1 ). Additionally, the Cf-integrated electrodes can have an extremely high mass loading of NMC 532 (70 mg cm –2 ) with a theoretical capacity of 14 mAh cm –2 . Thus, the practical full cells assembled with the Cfs-enabled electrodes exhibit an initial areal capacity of 4.1 mAh cm –2 and capacity retention of 90.4% at 500 cycles at a cycling rate of C/3, 1.5 mA cm –2 . Data collected from the operando isothermal microcalorimetry suggest that full cells utilizing the Cf anode experience less heat release from side reactions compared to cells utilizing a conventional graphite anode. Finally, this present approach is scalable and cost-effective and can fabricate practical LIBs that boast high areal capacity, rate performance, and a lengthy cycling lifetime.

25 ENERGY STORAGE↗

The Science and Engineering of Durable Ultralow PGM Catalysts (2012 DOE-EERE-FCT Annual Progress Report)

Minimizing the quantity of Pt group metals used in polymer membrane fuel cells (PEMFCs) is one of the remaining grand challenges for fuel cell commercialization. Tremendous progress has been achieved over the last two decades in decreasing the Pt loading required for efficient fuel cell performance. Unfortunately, the fluctuations in the price of Pt represent a substantial barrier to the economics of widespread fuel cell use. Durability and impurity tolerance are also challenges that are tightly coupled to fuel cell Pt electrode loading. Traditional approaches to decreasing the amount of Pt required for good performance include: (1) Increasing mass activity by decreasing Pt particle size by supporting on carbon; (2) Alloy formulation Pt-Co, Pt-Cr alloys to improve mass activity; (3) Increasing Pt utilization by optimization of electronic and ionic contact of the Pt particles; (4) Improving conductivity of the electronic and ionic conducting constituents of the membrane electrode assembly; and (5) Improving reactant to and product mass transport away from the electroactive sites. Recent novel approaches include the nanoengineering of core shell catalysts and Pt particles of unusual geometries such as nanowires/whiskers. The success of the aforementioned approaches has been great; however further advances using such approaches have been hampered by a lack of underlining scientific understanding of the catalyst activity, particle growth mechanisms, and optimization strategies for designing composite electrodes The objectives of this report are: (1) Development of durable, high mass activity Platinum Group Metal (PGM) cathode catalysts-enabling lower cost fuel cells; (2) Elucidation of the fundamental relationships between PGM catalyst shape, particle size and activity to help design better catalysts; (3) Optimization of the cathode electrode layer to maximize the performance of PGM catalysts-improving fuel cell performance and lowering cost; (4) Understanding the performance degradation mechanisms of high mass activity cathode catalysts-provide insights to better catalyst design; and (5) Development and testing of fuel cells using ultra-low loading high activity PGM catalysts-validation of advanced concepts.

08 HYDROGEN↗

Fast-Charging and Ultrahigh-Capacity Lithium Metal Anode Enabled by Surface Alloying

Li metal anodes are going through a great revival but they still encounter grand challenges. One often neglected issue is that most reported Li metal anodes are only cyclable under relatively low current density (<5 mA cm -2 ) and small areal capacity (<5 mAh cm -2 ), which essentially limits their high-power applications and results in ineffective Li utilization (<1%). Herein, it is reported that surface alloyed Li metal anodes can enable reversible cycling with ultrafast rate and ultralarge areal capacity. Low-cost Si wafers are used and are chemically etched down to 20-30 mu m membranes. Simply laminating a Si membrane onto Li foil results in the formation of LixSi alloy film fused onto Li metal with mechanical robustness and high Li-ion conductivity. Symmetric cell measurements show that the surface alloyed Li anode has excellent cycling stability, even under high current density up to 25 mA cm -2 and unprecedented areal capacity up to 100 mAh cm -2 . Furthermore, the surface alloyed Li anode is paired with amorphous MoS 3 cathode and achieves remarkable full-cell performance.

36 MATERIALS SCIENCE↗

Electrochemical Modeling and Performance of a Lithium- and Manganese-Rich Layered Transition-Metal Oxide Positive Electrode

The impedance of a lithium- and manganese-rich layered transition-metal oxide (MR-NMC) positive electrode, specifically Li 1.2 Ni 0.15 Mn 0.55 Co 0.1 O 2 , is compared to two other transition-metal layered oxide materials, specifically LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA) and Li 1.05 (Ni 1/3 Co 1/3 Mn 1/3 ) 0.95 O 2 (NMC). A more detailed electrochemical impedance spectroscopy (EIS) study is conducted on the LMR-NMC electrode, which includes a range of states-of-charge (SOCs) for both current directions (i.e. charge and discharge) and two relaxation times (i.e. hours and one hundred hours) before the EIS sweep. The LMR-NMC electrode EIS studies are supported by half-cell constant current and galvanostatic intermittent titration technique (GITT) studies. Two types of electrochemical models are utilized to examine the results. The first type is a lithium ion cell electrochemical model for intercalation active material electrodes that includes a complex active material/electrolyte interfacial structure. In conclusion, the other is a lithium ion half-cell electrochemical model that focuses on the unique composite structure of the bulk LMR-NMC materials.

25 ENERGY STORAGE↗

Investigation of Nanoparticle Degradation in Hydrogen Fuel Cell Systems through Automated Electron Microscopy

Proton exchange membrane fuel cells (PEMFC) are promising devices for the deployment of hydrogen-powered heavy-duty vehicles, providing a higher efficiency for similar driving range and fueling time than the existing ones. However, PEMFCs still encounter durability challenges mainly due to catalyst degradation in the cathode. Mitigating these performance losses requires a better understanding of the degradation mechanisms under heavy-duty accelerated stress tests (ASTs) [1]. Scanning transmission electron microscopy (STEM) combined with energy dispersive X-ray spectroscopy (EDS) are key tools for the analysis of Pt and PtCo nanoparticle size, spatial distribution and composition [2]. Electron tomography is also used to determine the rate and type of degradation of catalyst nanoparticles as a function of their position on the carbon support. In this work, automated data acquisition software, paired with a custom Python code, have been used to study the effect of different accelerated stress tests (ASTs) on nanoparticle coarsening [2]. Figure 1 shows high-angle annular dark-field (HAADF)-STEM images and EDS maps comparing the cathodes of membrane electrode assemblies (MEAs) following an electrocatalyst AST performed under H2/N2 with that of the heavy-duty AST performed under H2/air. We will discuss how AST conditions affect considerably the spatial distribution of the nanoparticles across the electrode between the membrane and microporous layer. Although the median particle size increased more in the MEA aged under the heavy-duty AST, as determined using a high-throughput image analysis, the quantitative EDS measurements demonstrate that the electrocatalyst AST resulted in more Pt and Co dissolution from the cathode, which is another important indicator of electrocatalyst degradation. We will further present the impact of the relative humidity (% RH) on the degradation mechanisms demonstrated using the same approach. Electron tomography has been used to distinguish the Pt nanoparticles residing on the carbon support surface (exterior) from those within the pore structure (interior) in order to determine the relative stability of interior and exterior nanoparticles. As shown in Figure 2, we will compare the Pt catalyst particle size at the beginning of test (BOT) and end of test (EOT), and discuss the importance of automating the electron tomography workflow, i.e. acquisition, reconstruction, and visualization, to increase sampling and determine the standard deviation of these measurement. The outlook for utilizing low-dose cryo-tomography for limiting damage to the catalyst, support, and especially proton-conducting ionomer will also be discussed [3].

Amichi, Lynda↗

Utilization of Ca K-Edge X-ray Absorption Near Edge Structure to Identify Intercalation in Potential Multivalent Battery Materials

Multivalent-ion batteries have been under investigation as a technology that can provide energy densities beyond that provided by lithium ion batteries. An emerging cation of interest is calcium, as it has similar electrochemical properties and size to sodium, and systems incorporating it have high theoretical density. Common techniques used to investigate intercalation, such as NMR, are currently unable to distinguish calcium's role in energy storage materials. In this work, we investigated the ability of calcium XANES to provide fingerprint identification of intercalated species using Ca ion exchanged Na x CoO 2 and a Ca(PF 6 ) 2 -based electrolyte as a case study. Ca XANES was able to detect intercalation down to concentrations of ~1 Ca per 950 Å 3 , even with residual electrolyte on the surface. The ability to observe the structure of the intercalated ion will enable the discovery of new electrolytes and intercalation cathodes by helping to confirm theoretical predictions, allowing multivalent batteries to become a viable high energy density storage technology.

25 ENERGY STORAGE↗

Oxygen-Based Anion Redox for Lithium Batteries

The importance of current Li-ion batteries (LIBs) in modern society cannot be overstated. While the energy demands of devices increase, the corresponding enhancements in energy density of battery technologies are highly sought after. Currently, many different battery concepts, such as Li-S and metal-air among many others, have been investigated. However, their practical implementation has mostly been restricted to the prototyping stage. In fact, most of these technologies require rework of existing Li-ion battery manufacturing facilities and will naturally incur resistance to change from industry. For this reason, one specifically attractive technology, anionic redox in transition metal oxides, has gained much attention in the recent years. Its ability to be directly used in already established processes and higher energy density with similar electrolyte formulation make it a key materials research direction for next generation Li-ion batteries. In regular LIBs, the redox active centers are the transition metal cation. In anion redox, both the anion (typically O) and the transition metal cation are utilized as redox centers with enormous implications for increasing energy density. This new material can be highly competitive for replacing the current LIB technologies. However, much is still unknown about its cyding mechanism. Upon activating the O redox couples, most cationic and anionic redox active materials will either evolve O 2 or undergo irreversible structural degradation with associated severe decreases in electrochemical performance. By understanding the transition from full anion redox to partial cationic and anionic redo; we hope readers can gain a deeper understanding of the topic. This Account will focus mainly on the work that was conducted by our group at Argonne National Laboratory. Herein, the phenomenon of cationic and anionic redox in a lithium-ion battery cathode will first be discussed. Our work in resonant inelastic X-ray scattering to investigate the spectroscopic features of O after delithiation has found potential "fingerprint" signals that could likely be used to identify and confirm reversible O redox if corroborated with other techniques. To follow, we will examine our work on Li-O 2 batteries. While our group and the research community have had many significant contributions and improvements to the field of Li-O 2 (such as decreasing overpotential and achieving cyclability in air environment), its practical application is still far from realization. Perhaps our most important contribution to this area is the discovery that Ir deposited on reduced graphene oxide can be used to halt the reduction of O 2 at the LiO 2 oxidation state. This not only significantly decreases the charge overpotential but also presents the important concept of oxidation-state controlled discharge. Subsequently, we will focus on our oxidation state-controlled redox-based charging of oxygen in a pure oxygen redox Li-ion battery. Future implications of this technology will be emphasized.

25 ENERGY STORAGE↗

Investigation of Rapid, Moderate Temperature Change Thermal Cycles of a Micro-Tubular Flame-Assisted Fuel Cell

Despite many efforts and improvements over the last few decades, two of the major challenges facing solid oxide fuel cells (SOFCs) are slow heating rates to operating temperature (typically < 5 °C · min–1) and a limited ability to thermal cycle (<200 cycles). Recently, a novel hybrid setup that combines a fuel-rich combustion reformer with a SOFC was developed and utilized to investigate rapid heating, cooling, and thermal cycling of a micro-tubular SOFC. In this work, 3000 moderate thermal cycles are conducted at a heating rate exceeding 140 °C · min–1 and a cooling rate that exceeded 100 °C · min–1. The open-circuit voltage (OCV) was analyzed over the 150 h test, and a low degradation rate of ~0.0008 V per 100 cycles per fuel cell was observed in the absence of the current collector degradation. Unlike a previous test, which was conducted at lower temperatures, significant degradation of the current collector was observed during this test. Electrochemical impedance spectroscopy shows that degradation in the SOFC was due to increases in ohmic losses, activation losses at the cathode, and increased concentration losses.

Electrochemistry↗

Electrochemistry-Induced Restructuring of Tin-Doped Indium Oxide Nanocrystal Films of Relevance to CO 2 Reduction

The electrochemical reduction of CO 2 into fuels using renewable electricity presents an opportunity to utilize captured CO 2 . Electrocatalyst development has been a primary focus of research in this area. This is especially true at the nanoscale, where researchers have focused on understanding nanostructure-property relationships. However, electrocatalyst structure may evolve during operation. Indium- and tin-based oxides have been widely studied as electrocatalysts for CO 2 reduction to formate, but evolution of these catalysts during operation is not well-characterized. Here, we report the evolution of nanoscale structure of precise tin-doped indium oxide nanocrystals under CO 2 reduction conditions. We show that sparse monolayer nanocrystal films desorb from the electrode upon charging, but thicker nanocrystal films remain, likely due to an increased number of physical contacts. Upon applying a cathodic voltage of –1.0 V vs RHE or greater, the original 10-nm diameter nanocrystals are no longer visible, and instead form a larger microstructural network. Elemental analysis suggests the network is an oxygen-deficient indium-tin metal alloy. We hypothesize that this morphological evolution is the result of nanocrystal sintering due to oxide reduction. Furthermore, these data provide insights into the morphological evolution of tin-doped indium oxide nanocrystal electrocatalysts under reducing conditions and highlight the importance of post-electrochemical structural characterization of electrocatalysts.

25 ENERGY STORAGE↗

Dynamics of electrochemical Pt dissolution at atomic and molecular levels

Understanding and controlling electrochemical interfaces at atomic and molecular levels have transformed electrochemistry into a science with clearly defined fundamental principles leading to significant impact on various electrochemical systems and devices. Although the principles guiding the activity of electrochemical reactions are quite well established, the driving forces that control stability are still poorly understood. Here we utilize in situ monitoring of the early stages of Pt dissolution using the stationary probe rotating disk electrode technique coupled to inductively coupled plasma mass spectrometry (SPRDE-ICPMS). Our unique SPRDE-ICPMS method provides picogram sensitivity levels that, in combination with STM, provide otherwise inaccessible information about the dissolution and redeposition of Pt(111) in acidic environments. We propose two distinct dissolution mechanisms that are active during oxide formation and subsequent oxide reduction. Whereas an electrochemical dissolution mechanism is observed during anodic Pt dissolution (Pt→Pt 2+ +2e - ), a combination of electrochemical (PtO*+2H + +2e - →Pt 0 +H 2 O) and chemical (PtO*+2H + →Pt 2+ +H 2 O) steps control the dissolution of Pt during the cathodic scan. The redeposition of Pt (Pt 2+ +2e - →Pt) observed on the cathodic scan is controlled by a delicate balance between the diffusion of Pt 2+ from the double layer and redeposition of Pt 2+ on Pt oxide-free sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Atomic layer deposited aluminum nitride for interface protection of lithium germanium thiophosphate solid electrolytes

Lithium germanium thiophosphate (LGPS) is an attractive solid-state electrolyte material due to its exceptionally high ionic conductivity (~1.2 × 10 –2 S cm –1 ), comparable to many organic liquid electrolytes commonly used in batteries. Despite the high conductivity of LGPS, the susceptibility of LGPS to deleterious degradation reactions has impeded its commercial adoption into solid-state batteries. In particular, the poor voltage stability of LGPS with high-voltage cathode or lithium metal potentials often results in dramatically increasing cell impedance during galvanic cycling. Here, we use aluminum nitride (AlN) as a protection layer for Li metal anode, applied directly to the LGPS at 250 °C using plasma-enhanced atomic layer deposition, to enhance cell performance by preventing LGPS-Li metal reactions. We compare the surface chemistry and electrochemical cycling performance of atomic layer-deposited AlN grown using both plasma N 2 and NH 3 precursors. Galvanostatic cycling and electrochemical impedance spectroscopy show that AlN-coated LGPS cells perform better than bare LGPS cells in contact with Li metal anodes, with the AlN able to improve cycling longevity by over a factor of 3 in certain cases. Finally, we utilize x-ray photoelectron spectroscopy (XPS) line scans to highlight the slow room-temperature reactivity between AlN and evaporated lithium metal, and a computational model is built to aid further XPS analysis.

25 ENERGY STORAGE↗

Technologies for Prolonging Cardiac Implantable Electronic Device Longevity

Prolonged longevity of cardiac implantable electronic devices (CIEDs) is needed not only as a passive response to match the prolonging life expectancy of patient recipients, but will also actively prolong their life expectancy by avoiding/deferring the risks (and costs) associated with device replacement. CIEDs are still exclusively powered by nonrechargeable primary batteries, and energy exhaustion is the dominant and an inevitable cause of device replacement. The longevity of a CIED is thus determined by the attrition rate of its finite energy reserve. The energy available from a battery depends on its capacity (total amount of electric charge), chemistry (anode, cathode, and electrolyte), and internal architecture (stacked plate, folded plate, and spiral wound). The energy uses of a CIED vary and include a background current for running electronic circuitry, periodic radiofrequency telemetry, high‐voltage capacitor reformation, constant ventricular pacing, and sporadic shocks for the cardiac resynchronization therapy defibrillators. The energy use by a CIED is primarily determined by the patient recipient's clinical needs, but the energy stored in the device battery is entirely under the manufacturer's control. A larger battery capacity generally results in a longer‐lasting device, but improved battery chemistry and architecture may allow more space‐efficient designs. Armed with the necessary technical knowledge, healthcare professionals and purchasers will be empowered to make judicious selection on device models and maximize the utilization of all their energy‐saving features, to prolong device longevity for the benefits of their patients and healthcare systems.

LAU, ERNEST W.↗

Quasi-In-Situ Analysis of Electrode Top Atomic Layers via High-Sensitivity Low-Energy Ion Scattering and Potential-Controlled Sample Transfer

Electrocatalytic reactions involve interfacial interactions between the surfaces of electrodes and reactive species at an electrolyte interface. There are presently no universal or unambiguous methods to directly assay the active top atomic layer composition that influences the reactivity of these electrodes under relevant operating conditions. Low-energy ion scattering (LEIS) spectroscopy is a surface characterization technique that yields compositional analysis of the outermost atomic layer of a material, but it must be performed in ultrahigh vacuum (UHV). Application of LEIS measurements to electrochemical materials that are removed from ambient liquid-phase environments thus leaves an open question as to whether the surface that is transferred to UHV is truly the surface that manifested during the electrochemical reaction. Toward the goal of preserving the active surface state, we developed a sample transfer workflow for LEIS enabling air-free removal and drying of an electrode from an electrochemical cell while maintaining control of the potential using an auxiliary electrode. The potential-controlled emersion method was demonstrated to give distinct potential-dependent surface compositions for a Cu−Pd alloy relative to removal after uncontrolled return to open-circuit potential. A Cu-enriched surface was found at anodic potential and a Pd-enriched surface at cathodic potential, suggesting that the approach can be used to retain representative atomic configurations during transfer. Since adsorbates will often persist from the reaction environment, conventional sample pretreatment methods for removal, including atomic O and atomic H exposure, were also contrasted. Both methods were found to differ with results from incidental low-dose depth profiling by the LEIS primary ion source, which removes adventitious species and surface atoms during the course of repeated measurements. These depth profiles were found to be sensitive to sample history and thus qualitatively informative, despite the possible changes induced by ion damage. The results exhibit (i) the need for complete control over the polarization state of the sample at all times (no excursions to open circuit during transfer) and (ii) the utility of low-dose depth profiling to capture changes in the near-surface composition.

Alloys↗

Alkali metal-sulfur secondary battery containing cathode material particulates

Provided is a rechargeable alkali metal-sulfur cell comprising an anode active material layer, an electrolyte, and a cathode active material layer comprising multiple particulates, wherein at least one of the particulates comprises one or a plurality of sulfur-containing material particles being embraced or encapsulated by a thin layer of a conductive sulfonated elastomer composite having from 0.01% to 50% by weight of a conductive reinforcement material dispersed in a sulfonated elastomeric matrix material, wherein the conductive reinforcement material is selected from graphene sheets, carbon nanotubes, carbon nanofibers, metal nanowires, conductive polymer fibers, or a combination thereof and the composite has a recoverable tensile strain from 2% to 500%, a lithium ion conductivity from 10−7 S/cm to 5×10−2 S/cm, and a thickness from 0.5 nm to 10 μm. This battery exhibits an excellent combination of high sulfur content, high sulfur utilization efficiency, high energy density, and long cycle life.

Zhamu, Aruna↗

A Review of the Use of Immobilized Ionic Liquids in the Electrochemical Conversion of CO2

This paper is a review on the application of imidazolium-based ionic liquids tethered to polymer backbones in the electrochemical conversion of CO2 to carbon monoxide and formic acid. These tethered ionic liquids have been incorporated into novel anion ion exchange membranes for CO2 electrolysis, as well as for ionomers that have been incorporated into the cathode catalyst layer, providing a co-catalyst for the reduction reaction. In using these tethered ionic liquids in the cathode catalyst composition, the cell operating current increased by a factor of two or more. The Faradaic efficiencies also increased by 20–30%. This paper provides a review of the literature, in addition to providing some new experimental results from Dioxide Materials, in the electrochemical conversion of CO2 to CO and formic acid.

09 BIOMASS FUELS↗

High-performance Ruddlesden–Popper perovskite oxide with in situ exsolved nanoparticles for direct CO 2 electrolysis

Carbon dioxide (CO 2 ) is one of the principal greenhouse gases accountable for global warming and extreme climate changes. Electrochemically converting CO 2 into carbon monoxide (CO) is a promising approach for CO 2 utilization in achieving industrial decarbonization. High-temperature CO 2 electrolysis via solid oxide electrolysis cells (SOECs) has great potential, including high-energy efficiency, fast electrode kinetics, and competitive cost; however, this technology still has challenges associated with developing highly active, robust CO 2 electrodes for SOECs. We report novel Ruddlesden–Popper structured Pr 1.2 Sr 0.8 Mn 0.4 Fe 0.6 O 4–δ (RP-PSMF) with in situ exsolved Fe nanoparticles as the CO 2 electrode in SOECs for direct CO 2 conversion to CO. The mechanism of CO 2 electrolysis is studied by using the distribution of relaxation times method from electrochemical impedance spectroscopy. La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 3–δ (LSGM)-electrolyte supported SOECs with the RP-PSMF cathode have achieved exceptionally high current densities of 2.90, 1.61, 0.91, and 0.48 A·cm –2 at an applied voltage of 1.5 V at 800, 750, 700, and 650 °C, respectively. Moreover, SOECs with the RP-PSMF cathode have exhibited a stable electrolysis performance for 100 h under a current cycling operation. Here, these results suggest that RP-PSMF with exsolved Fe nanoparticles is a highly promising cathode for high-temperature direct CO 2 electrolysis cells.

03 NATURAL GAS↗