Search NASA⌕ Search

SEARCH · Search NASA

Results for “dynamic loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Strain rate characterization of unidirectional graphite/epoxy composite

For an investigation of problems of composites at high strain rates with dominant wave propagation effects, such as dynamically loaded composite jet engine blades, the longitudinal, transverse, and in-plane shear properties of unidirectional SP 288/AS graphite/epoxy were measured at various strain rates ranging from quasi-static to over 500/s. The test specimens were rings 10.16 cm in diameter, 2.54 cm long, 6 to 8 plies thick, and with fibers at 0, 90, and 10 deg off-axis. Quasi-static testing was conducted in a fixture which applies hydraulic pressure to the ring specimens, and dynamic testing was conducted by applying an internal pressure pulse through a liquid in a special fixture. Dynamic stress-strain curves are presented. For the 0-deg specimens, the modulus increases with strain up to 20 percent of the static value. The modulus and strength increase sharply in the 90-deg rings with strain rate reaching values two to three times the corresponding static rate.

Daniel, I. M.↗

Influence of high-strain-rate compression and subsequent heat treatment on (TiNbZr) 89 (AlTa) 11 refractory high-entropy alloys: Dynamic-mechanical behavior and microstructural changes

This study explored the dynamic-mechanical behavior of a novel low-density (TiNbZr) 89 (AlTa) 11 refractory high-entropy alloy (RHEA) across strain rates ranging from 1.0×10 3 to 3.5×10 3 s –1 . A significant increase in the yield and ultimate compressive strengths with rising strain rates up to 3.0×10 3 s –1 was observed and attributed to enhanced dislocation activities and stress-induced microstructural transformations. The formation of the B2 phase and Zr 5 Al 3 precipitates was found to be crucial in bolstering the alloy strength at high strain rates. Beyond strain rates of 3.0×10 3 s –1 , a decrease in strength occurred due to thermal softening and strain localization. Microstructural analyses at 3.5×10 3 s –1 revealed grain refinement, the development of micro shear bands, and dislocation tangles, which were indicative of dynamic recrystallization. Besides, the findings also revealed that the post-dynamic compression heat treatment further enhanced the hardness and microstructural stability of the alloy. These results highlight the potential of the (TiNbZr) 89 (AlTa) 11 RHEA for applications requiring materials with high strength-to-weight ratios, particularly in dynamically loaded environments. It is expected that the results of this study will further advance our fundamental understanding of the behavior of RHEAs under extreme conditions, thereby opening new avenues for material innovation.

36 MATERIALS SCIENCE↗

Dynamic High-Temperature Tensile Characterization of an Iridium Alloy with Kolsky Tension Bar Techniques

In this study, conventional Kolsky tension bar techniques were modified to characterize an iridium alloy in tension at elevated strain rates and temperatures. The specimen was heated to elevated temperatures with an induction coil heater before dynamic loading; whereas, a cooling system was applied to keep the bars at room temperature during heating. A preload system was developed to generate a small pretension load in the bar system during heating in order to compensate for the effect of thermal expansion generated in the high-temperature tensile specimen. A laser system was applied to directly measure the displacements at both ends of the tensile specimen in order to calculate the strain in the specimen. A pair of high-sensitivity semiconductor strain gages was used to measure the weak transmitted force due to the low flow stress in the thin specimen at elevated temperatures. The dynamic high-temperature tensile stress–strain curves of a DOP-26 iridium alloy were experimentally obtained at two different strain rates (~1000 and 3000 s -1 ) and temperatures (~750 and 1030°C). The effects of strain rate and temperature on the tensile stress–strain response of the iridium alloy were determined. Finally, the iridium alloy exhibited high ductility in stress–strain response that strongly depended on strain-rate and temperature.

36 MATERIALS SCIENCE↗

An active homopolar magnetic bearing with high temperature superconductor (HTS) coils and ferromagnetic cores

A proof-of-feasibility demonstration showed that high temperature superconductor (HTS) coils can be used in a high-load, active magnetic bearing in liquid nitrogen. A homopolar radial bearing with commercially wound HTS (Bi 2223) bias and control coils produced over 200 lb (890 N) radial load capacity (measured non-rotating) and supported a shaft to 14000 rpm. The goal was to show that HTS coils can operate stably with ferromagnetic cores in a feedback controlled system at a current density similar to that in Cu in liquid nitrogen. Design compromises permitted use of circular coils with rectangular cross section. Conductor improvements will eventually permit coil shape optimization, higher current density and higher bearing load capacity. The bias coil, wound with non-twisted, multifilament HTS conductor, required negligible power to carry its direct current. The control coils were wound with monofilament HTS sheathed in Ag. These dissipated negligible power for direct current (i.e. for steady radial load components). When an alternating current (AC) was added, the AC component dissipated power which increased rapidly with frequency and quadratically with AC amplitude. In fact at frequencies above about 2 hz, the effective resistance of the control coil conductor actually exceeds that of the silver which is in electrical parallel with the oxide superconductor. This is at least qualitatively understandable in the context of a Bean-type model of flux and current penetration into a Type II superconductor. Fortunately the dynamic currents required for bearing stability are of small amplitude. These results show that while twisted multifilament conductor is not needed for stable levitation, twisted multifilaments will be required to reduce control power for sizable dynamic loads, such as those due to unbalance.

Brown, G. V.↗

Arbitrary Order Virtual Element Methods for High‐Order Phase‐Field Modeling of Dynamic Fracture

ABSTRACT Accurate modeling of fracture nucleation and propagation in brittle and ductile materials subjected to dynamic loading is important in predicting material damage and failure under extreme conditions. Phase‐field fracture models have garnered a lot of attention in recent years due to their success in representing damage and fracture processes in a wide class of materials and under a variety of loading conditions. Second‐order phase‐field fracture models are by far the most popular among researchers (and increasingly, among practitioners), but fourth‐order models have started to gain broader acceptance since their more recent introduction. The exact solution corresponding to these high‐order phase‐field fracture models has higher regularity. Thus, numerical solutions of the model equations can achieve improved accuracy and higher spatial convergence rates. In this work, we develop a virtual element framework for the high‐order phase‐field model of dynamic fracture. The virtual element method (VEM) can be regarded as a generalization of the classical finite element method. In addition to many other desirable characteristics, the VEM allows computing on polytopal meshes. Here, we use ‐conforming virtual elements and the generalized‐ time integration method for the momentum balance equation, and adopt ‐conforming virtual elements for the high‐order phase‐field equation. We verify our virtual element framework using classical quasi‐static benchmark problems and demonstrate its capabilities with the aid of numerical simulations of dynamic fracture in brittle materials.

42 ENGINEERING↗

Fuel assembly shaker and truck test simulation

This study continues the modeling support of the SNL shaker table task from 2013 and includes analysis of the SNL 2014 truck test campaign. Detailed finite element models of the fuel assembly surrogate used by SNL during testing form the basis of the modeling effort. Additional analysis was performed to characterize and filter the accelerometer data collected during the SNL testing. The detailed fuel assembly finite element model was modified to improve the performance and accuracy of the original surrogate fuel assembly model in an attempt to achieve a closer agreement with the low strains measured during testing. The revised model was used to recalculate the shaker table load response from the 2013 test campaign. As it happened, the results remained comparable to the values calculated with the original fuel assembly model. From this it is concluded that the original model was suitable for the task and the improvements to the model were not able to bring the calculated strain values down to the extremely low level recorded during testing. The model needs more precision to calculate strains that are so close to zero. The truck test load case had an even lower magnitude than the shaker table case. Strain gage data from the test was compared directly to locations on the model. Truck test strains were lower than the shaker table case, but the model achieved a better relative agreement of 100-200 microstrains (or 0.0001-0.0002 mm/mm). The truck test data included a number of accelerometers at various locations on the truck bed, surrogate basket, and surrogate fuel assembly. This set of accelerometers allowed an evaluation of the dynamics of the conveyance system used in testing. It was discovered that the dynamic load transference through the conveyance has a strong frequency-range dependency. This suggests that different conveyance configurations could behave differently and transmit different magnitudes of loads to the fuel even when traveling down the same road at the same speed. It is recommended that the SNL conveyance system used in testing be characterized through modal analysis and frequency response analysis to provide context and assist in the interpretation of the strain data that was collected during the truck test campaign.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The use of coherence functions to determine dynamic excitation sources on launch vehicle payloads

The problem of determining the relative contribution of simultaneous acoustic and mechanical inputs to the response of structures under combined dynamic loads was studied. An analytical technique developed by Bendat for calculating ordinary, partial, and multiple coherence functions, using an iterative nonmatrix approach was applied to data obtained from laboratory tests on a complex structural assembly. Testing was performed in an acoustically 'live' room. Up to three random inputs, having similar spectral content and varying degrees of mutual coherence, and a single output were used. Stationary and nonstationary inputs were used. It was concluded that the technique provided an effective method of identifying sources of dynamic excitation and evaluating their relative contributions to the measured output at structural resonances, for stationary random inputs. An attempt to apply the technique to nonstationary inputs did not yield consistent results.

Barrett, S.↗

Study of journal bearing dynamics using 3-dimensional motion picture graphics

Computer generated motion pictures of three dimensional graphics are being used to analyze journal bearings under dynamically loaded conditions. The motion pictures simultaneously present the motion of the journal and the pressures predicted within the fluid film of the bearing as they evolve in time. The correct prediction of these fluid film pressures can be complicated by the development of cavitation within the fluid. The numerical model that is used predicts the formation of the cavitation bubble and its growth, downstream movement, and subsequent collapse. A complete physical picture is created in the motion picture as the journal traverses through the entire dynamic cycle.

Brewe, D. E.↗

Smart Novel Semi-Active Tuned Mass Damper for Fixed-Bottom and Floating Offshore Wind (Paper)

The intention of this paper is to present the results of a novel smart semi-active tuned mass damper (SA-TMD), which mitigates unwanted loads for both fixed-bottom and floating offshore wind systems. The paper will focus on the most challenging water depths for both fixed-bottom and floating systems. A close to 38m Monopile and 55m Tension Leg Platform (TLP) will be considered. A technical development and trade-off analysis will be presented comparing the new system with existing passive non-linear TMD (N-TMD) technology and semi-active. TheSATMD works passively and activates itself with low power source under unwanted dynamic loading in less than 60msec. It is composed of both variable stiffness and damping elements coupled to a central pendulum mass. The analysis has been done numerically in both FAST(NREL) and Orcaflex (Orcina), and integrated in the Wind Turbine system employing CAD/CAE. The results of this work will pave the way for experimental testing to complete the technology qualification process. The load reductions under extreme and fatigue cases reach up significant levels at tower base, consequently reducing LCOE for fixed-bottom to floating wind solutions. The nacelle acceleration is reduced substantially under severe random wind and sea states, reducing the risks of failure of electromechanical components and blades at the rotor nacelle assembly. The SA-TMD system isa new technology that has not been applied previously in wind solutions. Structural damping devices aim to increase offshore wind turbine system robustness and reliability, which eases multiple substructures installations and global stability.

17 WIND ENERGY↗

Dynamic neural networks based on-line identification and control of high performance motor drives

In the automated and high-tech industries of the future, there wil be a need for high performance motor drives both in the low-power range and in the high-power range. To meet very straight demands of tracking and regulation in the two quadrants of operation, advanced control technologies are of a considerable interest and need to be developed. In response a dynamics learning control architecture is developed with simultaneous on-line identification and control. the feature of the proposed approach, to efficiently combine the dual task of system identification (learning) and adaptive control of nonlinear motor drives into a single operation is presented. This approach, therefore, not only adapts to uncertainties of the dynamic parameters of the motor drives but also learns about their inherent nonlinearities. In fact, most of the neural networks based adaptive control approaches in use have an identification phase entirely separate from the control phase. Because these approaches separate the identification and control modes, it is not possible to cope with dynamic changes in a controlled process. Extensive simulation studies have been conducted and good performance was observed. The robustness characteristics of neuro-controllers to perform efficiently in a noisy environment is also demonstrated. With this initial success, the principal investigator believes that the proposed approach with the suggested neural structure can be used successfully for the control of high performance motor drives. Two identification and control topologies based on the model reference adaptive control technique are used in this present analysis. No prior knowledge of load dynamics is assumed in either topology while the second topology also assumes no knowledge of the motor parameters.

Rubaai, Ahmed↗

ESTABLISHING ROCK OUTCROP TIME SERIES AT VARIOUS DEPTHS IN A NONLINEAR SOIL COLUMN

Nonlinear soil-structure interaction (NLSSI) analysis methods are currently being developed at Idaho National Laboratory (INL). Appendix B in ASCE 4 (2016) includes a framework for performing NLSSI analysis. For NLSSI analysis to be widely implemented in industry, it is important to demonstrate that accurate response in a dynamically loaded, nonlinear soil column can be produced. In performing NLSSI analysis, one approach is to consider vertically propagating shear and compressive waves that pass through a nonlinear soil column and into a structure. Using finite element techniques, the structure can be placed in a finite volume of nonlinear soil with a rock outcrop seismic time series applied to the bottom of the nonlinear soil. The necessary depth of the nonlinear soil mesh is dependent on the vertical soil stiffness when the model is in static and dynamic equilibrium. Run time, and therefore size of the meshed soil domain, is an important consideration when developing the NLSSI model. An approach is presented in this paper that establishes compatible rock outcrop seismic time series for reduced nonlinear soil mesh depths. To apply the approach, an example is developed using a reasonable soil column with a reasonable top-of-soil response spectrum. The approach is an iterative method which is applied in two steps. The first step is used to establish a reasonable rock outcrop time series at the highest depth considered. The second step is used to establish compatible rock outcrop time series at shallower depths.

42 ENGINEERING↗

Multi-Axis Independent Electromechanical Load Control for Docking System Actuation Development and Verification Using dSPACE

The development of highly complex and advanced actuation systems to meet customer demands has accelerated as the use of real-time testing technology expands into multiple markets at Moog. Systems developed for the autonomous docking of human rated spacecraft to the International Space Station (ISS), envelope multi-operational characteristics which place unique constraints on an actuation system. Real-time testing hardware has been used as a platform for incremental testing and development for the linear actuation system which controls initial capture and docking for vehicles visiting the ISS. This presentation will outline the role of dSPACE hardware as a platform for rapid control-algorithm prototyping as well as an Electromechanical Actuator (EMA) system dynamic loading simulator, both conducted at Moog to develop the safety critical Linear Actuator System (LAS) of the NASA Docking System (NDS).

Oesch, Christopher↗

Enhancements, Verification, and VMS Integration of VTOL Concept Vehicle Simulation Models

Advanced Rotorcraft Technology (ART) and the NASA Ames Aeromechanics branch have jointly developed FLIGHTLAB simulation models for Advanced Air Mobility (AAM) VTOL concept vehicles. The overarching purpose of the simulation model development is to establish a set of well defined reference vehicles for FLIGHTLAB users and the rotorcraft community. The ongoing research effort and enhancement of these AAM simulation models to fulfill the role of quality reference vehicles is this paper’s focus. The content of this paper expands on the established characteristics of these AAM models in three primary areas. First, enhancement of the lift+cruise and tiltwing models with elastic airframe properties is discussed. The process of setting up the elastic airframe model in FLIGHTLAB, as well as the impacts on flight characteristics are explained. The introduction of the elastic airframe modeling allows these models to be used in flight dynamics, loads, and vibration analysis of the configuration designs. Next, linear model generation from the enhanced simulation model is covered. Confirming the validity of the linearized models is of importance, as these linear models are utilized for flight control design and tuning for these experimental configurations. For the final focus, the progress towards implementation of these models into the NASA Ames Vertical Motion Simulator (VMS) is described. This task seeks to demonstrate the procedures of integrating a FLIGHTLAB flight simulation in the VMS environment, test fully integrated simulation with communication between flight dynamics, control, and propulsion models, and explore the essential aspects of simulation model integration in a full flight simulator environment. This includes I/O definition, initialization, trim, flying, etc. By expanding the capabilities of the AAM simulation models, they continue to develop as valuable and approachable modeling references.

VMS↗

2015 Occupant Protection Standing Review Panel

The 2015 Occupant Protection (OP) Risk Standing Review Panel (from here on referred to as the SRP) participated in a WebEx/teleconference with members of the Space Human Factors and Habitability (SHFH) Element, representatives from the Human Research Program (HRP), NASA Headquarters, and NASA Research and Education Support Services on November 3, 2015 (list of participants is in Section VII of this report). The SRP reviewed the updated research plans for the Risk of Injury from Dynamic Loads (OP Risk). The SRP agrees that the Gaps are relevant and appropriate to mitigate the injury risk. All the appropriate and relevant Tasks have been identified to fill the Gaps. Depending upon the findings, additional tasks may need to be identified or modified. Excellent progress has been made since the 2014 SRP meeting. Publications in peer-reviewed journals validate the scientific merit of the research findings. As detailed in this report, the SRP has specific comments, guidance, and information in the following areas: human finite element modeling, human vs. surrogate dynamic responses, chest injury risk curves, matched pair testing of Test device for Human Occupant Restraint (THOR) and Hybrid III, and disc herniation risk analysis.

Steinberg, Susan↗

Multi analysis of the effect of grain size on the dynamic behavior of microalloyed steels

This study presents some aspects of multiscale analysis and modeling of variously structured materials behavior in quasi-static and dynamic loading conditions. The investigation was performed for two different materials of common application: high strength microalloyed steel (HSLA, X65), and as a reference more ductile material, Ti-IF steel. The MaxStrain technique and one pass hot rolling processes were used to produce ultrafine-grained and coarse-grained materials. The efficiency and inhomogeneity of microstructure refinement were examined because of their important role in work hardening and the initiation and growth of fracture under tensile stresses. It is shown that the combination of microstructures characterized by their different features contributes to the dynamic behavior and final properties of the product. In particular, the role of solute segregation at grain boundaries as well as precipitation of carbonitrides in coarse and ultrafine-grained structures is assessed. The predicted mechanical response of ultrafine-grained structures, using modified KHL model is in reasonable agreement with the experiments. This is a result of proper representation of the role of dislocation structure and the grain boundary and their multiscale effects included in this model.

36 MATERIALS SCIENCE↗

Materials compatibility.

Objectives are to enable development and implementation of codes and standards for H{sub 2} containment components: (1) Evaluate data on mechanical properties of materials in H{sub 2} gas - Technical Reference on Hydrogen Compatibility of Materials; (2) Generate new benchmark data on high-priority materials - Pressure vessel steels, stainless steels; and (3) Establish procedures for reliable materials testing - Sustained-load cracking, fatigue crack propagation. Summary of this presentation are: (1) Completed measurement of cracking thresholds (K{sub TH}) for Ni-Cr-Mo pressure vessel steels in high-pressure H{sub 2} gas - K{sub TH} measurements required in ASME Article KD-10 (2) Crack arrest test methods appear to yield non-conservative results compared to crack initiation test methods - (a) Proposal to insert crack initiation test methods in Article KD-10 will be presented to ASME Project Team on Hydrogen Tanks, and (b) Crack initiation methods require test apparatus designed for dynamic loading of specimens in H{sub 2} gas; and (3) Demonstrated ability to measure fatigue crack growth of pressure vessel steels in high-pressure H{sub 2} gas - (a) Fatigue crack growth data in H{sub 2} required in ASME Article KD-10, and (b) Test apparatus is one of few in U.S. or abroad for measuring fatigue crack growth in >100 MPa H{sub 2} gas.

08 HYDROGEN↗

Continuum models for beam-like and plate-like lattice structures

A simple, rational approach is presented for developing continuum models for large repetitive beam-like and plate-like lattices with arbitrary configurations subjected to static, thermal and dynamic loadings. The continuum models for these structures are shear flexible beams and plates. They account for local effects in the repeating element of the actual structure and are characterized by their thermoelastic strain and kinetic energies from which the equations of motion and constitutive relations can be derived. The procedure for developing the expressions for thermoelastic strain and kinetic energies of the continuum involves introducing basic assumptions regarding the variation of the temperature, displacement and strain components in one or two directions (for plate-like and beam-like lattices) and obtaining effective thermoelastic and dynamic coefficients of the continuum in terms of material properties and geometry of the original lattice structure. The high accuracy of the continuum models developed is demonstrated by means of numerical examples.

Noor, A. K.↗

Algorithms for parallel flow solvers on message passing architectures

The purpose of this project has been to identify and test suitable technologies for implementation of fluid flow solvers -- possibly coupled with structures and heat equation solvers -- on MIMD parallel computers. In the course of this investigation much attention has been paid to efficient domain decomposition strategies for ADI-type algorithms. Multi-partitioning derives its efficiency from the assignment of several blocks of grid points to each processor in the parallel computer. A coarse-grain parallelism is obtained, and a near-perfect load balance results. In uni-partitioning every processor receives responsibility for exactly one block of grid points instead of several. This necessitates fine-grain pipelined program execution in order to obtain a reasonable load balance. Although fine-grain parallelism is less desirable on many systems, especially high-latency networks of workstations, uni-partition methods are still in wide use in production codes for flow problems. Consequently, it remains important to achieve good efficiency with this technique that has essentially been superseded by multi-partitioning for parallel ADI-type algorithms. Another reason for the concentration on improving the performance of pipeline methods is their applicability in other types of flow solver kernels with stronger implied data dependence. Analytical expressions can be derived for the size of the dynamic load imbalance incurred in traditional pipelines. From these it can be determined what is the optimal first-processor retardation that leads to the shortest total completion time for the pipeline process. Theoretical predictions of pipeline performance with and without optimization match experimental observations on the iPSC/860 very well. Analysis of pipeline performance also highlights the effect of uncareful grid partitioning in flow solvers that employ pipeline algorithms. If grid blocks at boundaries are not at least as large in the wall-normal direction as those immediately adjacent to them, then the first processor in the pipeline will receive a computational load that is less than that of subsequent processors, magnifying the pipeline slowdown effect. Extra compensation is needed for grid boundary effects, even if all grid blocks are equally sized.

Vanderwijngaart, Rob F.↗