Search NASA⌕ Search

SEARCH · Search NASA

Results for “High gradient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Evaluation of the Gafchromic{sup Registered-Sign} EBT2 film for the dosimetry of radiosurgical beams

Purpose: Radiosurgery uses small fields and high-radiation doses to treat intra- and extracranial lesions in a single session. The lack of a lateral electronic equilibrium and the presence of high-dose gradients in these fields are challenges for adequate measurements. The availability of radiation detectors with the high spatial resolution required is restricted to only a few. Stereotactic diodes and EBT radiochromic films have been demonstrated to be good detectors for small-beam dosimetry. Because the stereotactic diode is the standard measurement for the dosimetry of radiosurgical beams, the goal of this work was to perform measurements with the radiochromic film Gafchromic{sup Registered-Sign} EBT2 and compare its results with a stereotactic diode. Methods: Total scatter factors, tissue maximum, and off-axis ratios from a 6 MV small photon beams were measured using EBT2 radiochromic film in a water phantom. The film-measured data were evaluated by comparing it with the data measured with a stereotactic field diode (IBA-Dosimetry). Results: The film and diode measurements had excellent agreement. The differences between the detectors were less than or equal to 2.0% for the tissue maximum and the off-axis ratios. However, for the total scatter factors, there were significant differences, up to 4.9% (relative to the reference field), for field sizes less than 1.0 cm. Conclusions: This work found that the Gafchromic{sup Registered-Sign} EBT2 film is adequate for small photon beam measurements, particularly for tissue maximum and off-axis ratios. However, careful attention must be taken when measuring output factors of small beams below 1.0 cm due to the film's energy dependence. The measurement differences may be attributable to the film's active layer composition because EBT2 incorporates higher Z elements (i.e., bromide and potassium), hence revealing a potential energy dependence for the dosimetry of small photon beams.

60 APPLIED LIFE SCIENCES↗

Si-Cr-Al-Mn Alloy for High Specific Resistivity

Laboratory material produced in budget period one met the target resistivity, mechanical and magnetic requirements for the Go/No-Go decision to move to industrial trials. The chosen chemistry settled on a high Cr strategy, with moderate Mn and Al additions, providing a good comprise on core loss and induction with minimal impact on mechanical properties, important to successful downstream processing. Industrial trials began in budget period two with the chosen chemistry, referred to as Alloy X. Difficulties occurred during initial hot rolling trials. Reheating the material using the standard NOES practice caused slab cracking from high thermal gradients in areas exposed to the roof burners, this was solved using a modified reheat practice. High Cr caused poor dynamic recrystallization during hot rolling, which was solved using a modified hot rolling practice. The high Cr content of the steel also caused poor decarburization during final annealing, which necessitated lowering the melt carbon aim for the final heat, together with a modified decarburization practice. Steel was finished to final thicknesses of 0.20 – 0.50 mm and evaluated for magnetic and mechanical properties. Although the target core loss for the 0.25 and 0.35 mm material was not achieved, significant reductions in high frequency core loss were measured, compared to equivalent commercially available material. Alloy X at 0.35 mm showed a 26 % and 23 % improvement at 400 HZ and 1000 Hz respectively, over Cliffs’ M-19 (0.35 mm) commercially available NOES. At 0.25 mm, Alloy X showed a 23 % and a 26 % improvement at 400 HZ and 1000 Hz respectively, over Cliffs’ HF-10 (0.25 mm) commercially available NOES. The 0.25 mm product was chosen for motor efficiency evaluation. ORNL collaborated with Cleveland-Cliffs (CC) to build, assemble, and test two 5HP motors: a baseline motor with M19 steel and a motor made with high efficiency steel (Alloy X) developed for the project. Overall, results were as expected with comparable performance at low speeds, and with more than 8% efficiency improvement for high speeds. Increased motor steel efficiency at high frequencies not only results in direct efficiency improvements but can yield reductions in motor size and cost by facilitating higher operation speeds, or by increasing the number of poles in the machine. This allows the production of more power-dense motors which are sometimes avoided with conventional material due to increased core losses. The material developed on this project provides more viable options for achieving improved motor efficiency or reduced motor size and cost.

36 MATERIALS SCIENCE↗

Discontinuous Skeletal Gradient Discretisation methods on polytopal meshes

Here, in this work we develop arbitrary-order Discontinuous Skeletal Gradient Discretisations (DSGD) on general polytopal meshes. Discontinuous Skeletal refers to the fact that the globally coupled unknowns are broken polynomials on the mesh skeleton. The key ingredient is a high-order gradient reconstruction composed of two terms: (i) a consistent contribution obtained mimicking an integration by parts formula inside each element and (ii) a stabilising term for which sufficient design conditions are provided. An example of stabilisation that satisfies the design conditions is proposed based on a local lifting of high-order residuals on a Raviart–Thomas–Nédélec subspace. We prove that the novel DSGDs satisfy coercivity, consistency, limit-conformity, and compactness requirements that ensure convergence for a variety of elliptic and parabolic problems. Lastly, links with Hybrid High-Order, non-conforming Mimetic Finite Difference and non-conforming Virtual Element methods are also studied. Numerical examples complete the exposition.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A Fluid Pulse on the Hikurangi Subduction Margin: Evidence From a Heat Flux Transect Across the Upper Limit of Gas Hydrate Stability: Fluid Pulse on the Hikurangi Margin

A transect of seafloor heat probe measurements on the Hikurangi Margin shows a significant increase of thermal gradients upslope of the updip limit of gas hydrate stability at the seafloor. We interpret these anomalously high thermal gradients as evidence for a fluid pulse leading to advective heat flux, while endothermic cooling from gas hydrate dissociation depresses temperatures in the hydrate stability field. Previous studies predict a seamount on the subducting Pacific Plate to cause significant overpressure beneath our study area, which may be the source of the fluid pulse. Double-bottom simulating reflections are present in our study area and likely caused by uplift based on gas hydrate phase boundary considerations, although we cannot exclude a thermogenic origin. We suggest that uplift may be associated with the leading edge of the subducting seamount. Our results provide further evidence for the transient nature of fluid expulsion in subduction zones.

58 GEOSCIENCES↗

Optimal Design of Functionally Graded Metallic Foam Insulations

The focus of our work has been on developing an insight into the physics that govern the optimum design of thermal insulation for use in thermal protection systems of launch vehicle. Of particular interest was to obtain optimality criteria for designing foam insulations that have density (or porosity) distributions through the thickness for optimum thermal performance. We investigate the optimum design of functionally graded thermal insulation for steady state heat transfer through the foam. We showed that the heat transfer in the foam has competing modes, of radiation and conduction. The problem assumed a fixed inside temperature of 400 K and varied the aerodynamic surface heating on the outside surface from 0.2 to 1.0 MW/sq m. The thermal insulation develops a high temperature gradient through the thickness. Investigation of the model developed for heat conduction in foams showed that at high temperatures (as on outside wall) intracellular radiation dominates the heat transfer in the foam. Minimizing radiation requires reducing the pore size, which increases the density of the foam. At low temperatures (as on the inside wall), intracellular conduction (of the metal and air) dominates the heat transfer. Minimizing conduction requires increasing the pore size. This indicated that for every temperature there was an optimum value of density that minimized the heat transfer coefficient. Two optimization studies were performed. One was to minimize the heat transmitted though a fixed thickness insulation by varying density profiles. The second was to obtain the minimum mass insulation for specified thickness. Analytical optimality criteria were derived for the cases considered. The optimality condition for minimum heat transfer required that at each temperature we find the density that minimizes the heat transfer coefficient. Once a relationship between the optimum heat transfer coefficient and the temperature was found, the design problem reduced to the solution of a simple nonlinear differential equation. Preliminary results of this work were presented at the American Society of Composites meeting, and the final version was submitted for publication in the AIAA Journal. In addition to minimizing the transmitted heat, we investigated the optimum design for minimum weight given an acceptable level of heat transmission through the insulation. The optimality criterion developed was different from that obtained for minimizing beat transfer coefficient. For minimum mass design, we had to find for a given temperature the optimum density, which minimized the logarithmic derivative of the insulation thermal conductivity with respect to its density. The logarithmic derivative is defined as the ratio of relative change in the dependent response (thermal conductivity) to the relative change in the independent variable (density). The results have been documented as a conference paper that will be presented at the upcoming AIAA.

Haftka, Raphael T.↗

G5.89-0.39: A compact H II region with a very dense circumstellar dust torus

We present the results of high angular resolution infrared observations of the compact H II region G5.89-0.39. Subarcsecond imaging at 1.65, 2.2, 3.6, and 4.8 microns and diffraction-limited scans at 50 and 100 microns have been obtained at NASA's Infrared Telescope Facility and Kupier Airborne Observatory and the Canada-France-Hawaii Telescope. We find a bipolar source morphology at the shortest infrared wavelengths, a compact single source at 4-5 microns, similar to that seen at 10 microns, and a very high optical depth, barely resolved far-infrared source. Spherical radiative transfer models have been used to estimate dust envelope properties; in spite of the obvious nonspherical geometry at short wavelengths, these models provide strong constraints on the overall properties of the circumnebular envelope. We find that the bulk of the circumstellar dust must be relatively close to the H II region, with a relatively steep gradient. The high column densities and steep density gradient imply densities at the inner edge of the cloud of order 10(exp 7)-10(exp 8)/cc. These results suggest that the compact H II region is surrounded by a very dense dust torus.

Harvey, Paul M.↗

On possibility of low-emittance high-energy muon source based on plasma wakefield acceleration

We report plasma wakefield acceleration (PWA) channels are characterized by very high accelerating gradients and very strong focusing fields. We propose to employ these properties for effective production of low emittance high energy muon beams, consider muon beam dynamics in the PWFA cell and analyze various options and potential of the PWA-based muon sources.

43 PARTICLE ACCELERATORS↗

Radial and latitudinal gradients in the interplanetary magnetic field - Evidence for meridional flux transport

Magnetic field data obtained by the Pioneer 10 and 11 spacecraft in the heliosphere from 1972-1982 and earth orbiting satellite data are examined in terms of radial and latitudinal gradients in the field components and magnitude. The data reveal that higher than expected gradients are observed in the magnetic field and time variations affect the field throughout the low-latitude heliosphere. It is determined that the high radial gradient is caused by meridional flux transport with low-latitude field lines moving to higher heliographic latitudes. High pressure near the solar equator and pressure due to heating in compressive solar wind interaction regions and the large field magnitudes that occur in these regions are investigated as mechanisms that produce the meridional flux. A solar cycle variation in the level of flux transport is analyzed.

Thomas, B. T.↗

Enhancing water and oxygen transport through electrode engineering for AEM water electrolyzers

Anion-exchange membrane water electrolyzers (AEMWEs) can accelerate the deployment of more efficient and affordable hydrogen production solutions. Here, electrode structure is shown to affect water back-diffusion and oxygen transport, which, in return, governs overpotential behaviors in AEMWEs. Measurements indicate that electrode with copious catalytic sites produces water close to the AEM, creating a higher water gradient and driving water back-diffusion, which improves membrane hydration and mass transport. In situ measurement reveals a high pH gradient near the anode surface, which affects anode kinetics. Operando measurement shows reduced oxygen accumulation when decoupling oxygen production and transport on anode. Catalyst ink rheology and stability are tuned with additives to realize scalable fabrication of electrodes with enhanced transport features, allowing AEMWE to operate at 2 A cm−2 for over 1,000+ h at a 2.3 μV h−1 degradation rate. Analysis during and post-durability provides insights into degradation mechanisms. This work demonstrates an electrode design strategy for efficient and durable AEMWEs.

AEM↗

Thermoacoustic Soret separation

In a fluid mixture in a channel with an axial time-averaged temperature gradient, high-amplitude oscillating flow can greatly increase the axial flux of thermal diffusion (Soret) separation of the components of the mixture. The enhancement occurs when the oscillating lateral temperature gradient greatly exceeds the axial gradient, causing a large oscillating concentration that can be favorably time-phased with the oscillating flow. This process can occur even with a negligible pressure oscillation or with a negligible temperature response to pressure, as is the case in most liquid solutions. The thermal boundary condition imposed by realistic solids on thermoacoustic liquids is imperfect, adding mathematical complications that are absent for typical gases, for which the solid surface is temporally isothermal. Compared with gas mixtures, the high Lewis number in typical liquid solutions reduces the separation flux associated with the time-averaged temperature gradient, but it also reduces the remixing associated with the time-averaged mole-fraction gradient. For large enough channels, the second-law separation efficiency is only slightly reduced from that of steady liquid Soret separation.

36 MATERIALS SCIENCE↗

A Lattice for a Hybrid Fast-Ramping Muon Accelerator to 750 GeV

We describe a lattice for accelerating muons from 375 GeV to 750 GeV. The lattice is a fast-ramping synchrotron with a mixture of fixed-field superconducting dipoles and warm dipoles, so as to have a high average bending field while still being able to rapidly change the average bending field as the beam momentum increases. For a 1.5 TeV center of mass muon collider, muons must be rapidly accelerated to 750 GeV. To accomplish this efficiently, we wish to make as many passes through the RF cavities as possible, while keeping the average RF gradients sufficiently high to avoid excess muon decays. A synchrotron where the magnets are very rapidly ramped has been envisioned as one option to accomplish this. The entire acceleration cycle takes place in less than 1 ms, presenting a technological challenge for the magnets. Clearly superconducting magnets cannot be ramped on this time scale, so instead room-temperature magnets will be ramped. To keep losses low, dipoles can use grain-oriented silicon steel, but quadrupoles will probably need to use more conventional steel, giving a lower maximum field for these high ramping rates. If we want to have a large average RF gradient and simultaneously make a large number of passes through the RF cavities, the average bending field must be high. To achieve such a large bending field while rapidly ramping magnets, it has been proposed to use a hybrid lattice consisting of interleaved superconducting dipoles and bipolar ramped dipoles.

43 PARTICLE ACCELERATORS↗

5.5-7.5 MeV Proton Generation by a Moderate-Intensity Ultrashort-Pulse Laser Interaction with H{sub 2}O Nanowire Targets

We report on the first generation of 5.5-7.5 MeV protons by a moderate-intensity short-pulse laser ({approx}5x10{sup 17} W/cm{sup 2}, 40 fsec) interacting with frozen H{sub 2}O nanometer-size structure droplets (snow nanowires) deposited on a sapphire substrate. In this setup, the laser intensity is locally enhanced by the snow nanowire, leading to high spatial gradients. Accordingly, the nanoplasma is subject to enhanced ponderomotive potential, and confined charge separation is obtained. Electrostatic fields of extremely high intensities are produced over the short scale length, and protons are accelerated to MeV-level energies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The plug-based nanovolume Microcapillary Protein Crystallization System (MPCS)

The Microcapillary Protein Crystallization System (MPCS) embodies a new semi-automated plug-based crystallization technology which enables nanolitre-volume screening of crystallization conditions in a plasticware format that allows crystals to be easily removed for traditional cryoprotection and X-ray diffraction data collection. Protein crystals grown in these plastic devices can be directly subjected to in situ X-ray diffraction studies. The MPCS integrates the formulation of crystallization cocktails with the preparation of the crystallization experiments. Within microfluidic Teflon tubing or the microfluidic circuitry of a plastic CrystalCard, {approx}10-20 nl volume droplets are generated, each representing a microbatch-style crystallization experiment with a different chemical composition. The entire protein sample is utilized in crystallization experiments. Sparse-matrix screening and chemical gradient screening can be combined in one comprehensive 'hybrid' crystallization trial. The technology lends itself well to optimization by high-granularity gradient screening using optimization reagents such as precipitation agents, ligands or cryoprotectants.

59 BASIC BIOLOGICAL SCIENCES↗

Mo-100 Disk Structural Integrity Tests I

The NorthStar pressed and sintered 29 mm diameter, 0.5 mm thick Mo-100 disks will be subjected to large temperature gradients when in beam during production. The beam preferentially heats the disk center, while the aggressive cooling by the helium keeps areas outside the beam spot relatively cool. The result is a temperature gradient of up to 900°C over the radial distance of 14.5 mm. To test the disk integrity with this high temperature gradient, a special holder for a single disk was made such that proper cooling can be applied as in the design target and the disk heating can be replicated with induction heating. NorthStar press and sintered disks were used for these tests.

36 MATERIALS SCIENCE↗

Simulations of Dynamics and Transport during the September 2002 Antarctic Major Warming

A mechanistic model simulation initialized on 14 September 2002, forced by 100-hPa geopotential heights from Met Office analyses, reproduced the dynamical features of the 2002 Antarctic major warming. The vortex split on approx.25 September; recovery after the warming, westward and equatorward tilting vortices, and strong baroclinic zones in temperature associated with a dipole pattern of upward and downward vertical velocities were all captured in the simulation. Model results and analyses show a pattern of strong upward wave propagation throughout the warming, with zonal wind deceleration throughout the stratosphere at high latitudes before the vortex split, continuing in the middle and upper stratosphere and spreading to lower latitudes after the split. Three-dimensional Eliassen-Palm fluxes show the largest upward and poleward wave propagation in the 0(deg)-90(deg)E sector prior to the vortex split (coincident with the location of strongest cyclogenesis at the model's lower boundary), with an additional region of strong upward propagation developing near 180(deg)-270(deg)E. These characteristics are similar to those of Arctic wave-2 major warmings, except that during this warming, the vortex did not split below approx.600 K. The effects of poleward transport and mixing dominate modeled trace gas evolution through most of the mid- to high-latitude stratosphere, with a core region in the lower-stratospheric vortex where enhanced descent dominates and the vortex remains isolated. Strongly tilted vortices led to low-latitude air overlying vortex air, resulting in highly unusual trace gas profiles. Simulations driven with several meteorological datasets reproduced the major warming, but in others, stronger latitudinal gradients at high latitudes at the model boundary resulted in simulations without a complete vortex split in the midstratosphere. Numerous tests indicate very high sensitivity to the boundary fields, especially the wave-2 amplitude. Major warmings occurred for initial fields with stronger winds and larger vortices, but not smaller vortices, consistent with the initiation of wind-deceleration by upward-propagating waves near the poleward edge of the region where wave 2 can propagate above the jet core. Thus, given the observed 100-hPa boundary forcing, stratospheric preconditioning is not needed to reproduce a major warming similar to that observed. The anomalously strong forcing in the lower stratosphere can be viewed as the primary direct cause of the major warming.

winds↗

A compositional gradient Ce1−xZrxO2 buffer architecture for producing high-performance YBCO film

Highlights: • The compositional gradient CZO buffer architecture can help improve the biaxial texture of YBCO film. • The high density stacking faults are directly observed via a spherical aberration corrected transmission electron microscope. • The enhanced flux pinning force and current-carrying capacity of YBCO films are achieved as a result of lattice strains. - Abstract: In this work, YBCO films were epitaxially grown on Ce{sub 1−x}Zr{sub x}O{sub 2} (CZO) buffered yttria stabilized zirconia (YSZ) single crystal substrates through a fluorine-free sol-gel process. The influence of two different CZO buffer architectures on the microstructure and superconducting properties of YBCO films was investigated. According to XRD results in combination with (S)TEM analysis, it was confirmed that YBCO film grown on the gradient CZO buffer layer (CZO-G) exhibits better in-plane and out-of-plane texture than YBCO film deposited on the uniform CZO buffer layer (CZO-20). And besides, the superconducting performances especially the current-carrying capacity under magnetic field of the former was much higher than that of the latter, which means that the enhanced flux pinning force will be presented in YBCO film on CZO-G buffer layer. The maximum pinning force of the YBCO film grown on CZO-G buffer architecture is up to 17.67 GN/m{sup 3} @ 65 K. HR-STEM analysis shows that the stacking faults within YBCO matrix gave rise to the considerable nanoscale lattice-strains which may suppress the formation of Copper pairs and produce nanoscale non-superconducting regions served as pinning centers to significantly improve the flux pinning performance of YBCO film. Given the above, it has been implied that high-performance YBCO coated conductor can be developed by using a compositional gradient Ce{sub 1−x}Zr{sub x}O{sub 2} films as buffer architecture.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Induction Heating Model of Cermet Fuel Element Environmental Test (CFEET)

Deep space missions with large payloads require high specific impulse and relatively high thrust to achieve mission goals in reasonable time frames. Nuclear Thermal Rockets (NTR) are capable of producing a high specific impulse by employing heat produced by a fission reactor to heat and therefore accelerate hydrogen through a rocket nozzle providing thrust. Fuel element temperatures are very high (up to 3000 K) and hydrogen is highly reactive with most materials at high temperatures. Data covering the effects of high‐temperature hydrogen exposure on fuel elements are limited. The primary concern is the mechanical failure of fuel elements due to large thermal gradients; therefore, high‐melting‐point ceramics‐metallic matrix composites (cermets) are one of the fuels under consideration as part of the Nuclear Cryogenic Propulsion Stage (NCPS) Advance Exploration System (AES) technology project at the Marshall Space Flight Center. The purpose of testing and analytical modeling is to determine their ability to survive and maintain thermal performance in a prototypical NTR reactor environment of exposure to hydrogen at very high temperatures and obtain data to assess the properties of the non‐nuclear support materials. The fission process and the resulting heating performance are well known and do not require that active fissile material to be integrated in this testing. A small‐scale test bed; Compact Fuel Element Environmental Tester (CFEET), designed to heat fuel element samples via induction heating and expose samples to hydrogen is being developed at MSFC to assist in optimal material and manufacturing process selection without utilizing fissile material. This paper details the analytical approach to help design and optimize the test bed using COMSOL Multiphysics for predicting thermal gradients induced by electromagnetic heating (Induction heating) and Thermal Desktop for radiation calculations.

Gomez, C. F.↗

Induction Heating Model of Cermet Fuel Element Environmental Test (CFEET)

Deep space missions with large payloads require high specific impulse and relatively high thrust to achieve mission goals in reasonable time frames. Nuclear Thermal Rockets (NTR) are capable of producing a high specific impulse by employing heat produced by a fission reactor to heat and therefore accelerate hydrogen through a rocket nozzle providing thrust. Fuel element temperatures are very high (up to 3000 K) and hydrogen is highly reactive with most materials at high temperatures. Data covering the effects of high‐temperature hydrogen exposure on fuel elements are limited. The primary concern is the mechanical failure of fuel elements due to large thermal gradients; therefore, high‐melting‐point ceramics‐metallic matrix composites (cermets) are one of the fuels under consideration as part of the Nuclear Cryogenic Propulsion Stage (NCPS) Advance Exploration System (AES) technology project at the Marshall Space Flight Center. The purpose of testing and analytical modeling is to determine their ability to survive and maintain thermal performance in a prototypical NTR reactor environment of exposure to hydrogen at very high temperatures and obtain data to assess the properties of the non‐nuclear support materials. The fission process and the resulting heating performance are well known and do not require that active fissile material to be integrated in this testing. A small‐scale test bed; Compact Fuel Element Environmental Tester (CFEET), designed to heat fuel element samples via induction heating and expose samples to hydrogen is being developed at MSFC to assist in optimal material and manufacturing process selection without utilizing fissile material. This paper details the analytical approach to help design and optimize the test bed using COMSOL Multiphysics for predicting thermal gradients induced by electromagnetic heating (Induction heating) and Thermal Desktop for radiation calculations.

Gomez, Carlos F.↗