Search NASA⌕ Search

SEARCH · Search NASA

Results for “experimental methods development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1940

An Investigation of Sheet-stiffener Panels Subjected to Compression Loads with Particular Reference to Torsionally Weak Stiffeners

A total of 183 panel specimens of 24ST aluminum alloy with nominal thickness of 0.020, and 0.040 inch with extruded bulb-angle sections of 12 shapes spaced 4 and 5 inches as stiffeners were tested to obtain the buckling stress and the amplitude of the maximum wave when buckled. Bulb angles from 3 to 27 1/2 inches long were tested as pin-end columns. The experimental data are presented as stress-strain and column curves and in tabular form. Some comparisons with theoretical results are presented. Analytical methods are developed that make it possible for the designer to predict with reasonable accuracy the buckling stress and the maximum-wave amplitude of the sheet in stiffened-panel combinations. The scope of the tests was insufficient to formulate general design criteria but the results are presented as a guide for design and an indication of the type of theoretical and experimental work that is needed.

LOADS - COLUMNS↗
NASA NTRS1998

Progressive Failure And Life Prediction of Ceramic and Textile Composites

An engineering approach to predict the fatigue life and progressive failure of multilayered composite and textile laminates is presented. Analytical models which account for matrix cracking, statistical fiber failures and nonlinear stress-strain behavior have been developed for both composites and textiles. The analysis method is based on a combined micromechanics, fracture mechanics and failure statistics analysis. Experimentally derived empirical coefficients are used to account for the interface of fiber and matrix, fiber strength, and fiber-matrix stiffness reductions. Similar approaches were applied to textiles using Repeating Unit Cells. In composite fatigue analysis, Walker's equation is applied for matrix fatigue cracking and Heywood's formulation is used for fiber strength fatigue degradation. The analysis has been compared with experiment with good agreement. Comparisons were made with Graphite-Epoxy, C/SiC and Nicalon/CAS composite materials. For textile materials, comparisons were made with triaxial braided and plain weave materials under biaxial or uniaxial tension. Fatigue predictions were compared with test data obtained from plain weave C/SiC materials tested at AS&M. Computer codes were developed to perform the analysis. Composite Progressive Failure Analysis for Laminates is contained in the code CPFail. Micromechanics Analysis for Textile Composites is contained in the code MicroTex. Both codes were adapted to run as subroutines for the finite element code ABAQUS and CPFail-ABAQUS and MicroTex-ABAQUS. Graphic user interface (GUI) was developed to connect CPFail and MicroTex with ABAQUS.

Xue, David Y.↗
NASA NTRS2022

AST Critical Propulsion and Noise Reduction Technologies for Future Commercial Subsonic Engines Aeroacoustic Prediction Codes - Supplement: Code Descriptions and Users Guides

This report describes work performed on Contract NAS3–27720 AoI 13 as part of the NASA Advanced Subsonic Transport (AST) Noise Reduction Technology effort. Computer codes were developed to provide quantitative prediction, design, and analysis capability for several aircraft engine noise sources. The objective was to provide improved, physics-based tools for the exploration of noise-reduction concepts and the understanding of experimental results. Methods and codes focused on fan broadband and “buzz saw” noise and on low-emissions combustor noise and complement work done by other contractors under the NASA AST program to develop methods and codes for fan harmonic tone noise and jet noise. The methods and codes developed and reported herein employ a wide range of approaches, from the strictly empirical to the completely computational, with some being semiempirical, analytical, and/or analytical/computational. Emphasis was on capturing the essential physics while still considering method or code utility as a practical design and analysis tool for everyday engineering use. Codes and prediction models were developed for: (1) an improved empirical correlation model for fan rotor exit flow mean and turbulence properties, for use in predicting broadband noise generated by rotor exit flow turbulence interaction with downstream stator vanes; (2) fan broadband noise models for rotor and stator/turbulence interaction sources including 3D effects, noncompact-source effects, directivity modeling, and extensions to the rotor supersonic tip-speed regime; (3) fan multiple-pure-tone in-duct sound pressure prediction methodology based on CFD analysis; and (4) low-emissions combustor prediction methodology and computer code based on CFD and actuator disk theory. In addition, the relative importance of dipole and quadrupole source mechanisms was studied using direct CFD source computation for a simple cascade/gust interaction problem, and an empirical combustor-noise correlation model was developed from engine acoustic test results. This work provided several insights on potential approaches to reducing aircraft engine noise. Code development is described in Volume I, and those insights are discussed. Volume II documents the computer codes developed and gives instructions on how to use them.

Philip Gliebe↗
DOE OSTI2025

Further Development of the Tamped Richtmyer-Meshkov Instability Method and Application to Molybdenum Dynamic Strength Calibration and Tabulation

The high pressure and high strain rate dynamic strength of Mo is experimentally and computationally investigated in the 3–20 GPa stress, 50–600 C temperature, and 10 5 –10 6 /s strain rate regimes using a modified tamped Richtmyer-Meshkov instability (RMI) method. Modifications to the tamped RMI method include a method to determine loading states during strain, a new strength calibration function based on interface shape, and a robust uncertainty quantification method. These modifications improve fidelity of the tamped RMI method, allowing evaluation of the compensating effects of pressure hardening, strain rate hardening, strain hardening, and thermal softening. The new calibration function based on interface shape is not limited to sinusoidal corrugations and could be applied to additional interface shapes. Plate impact experiments are performed at Argonne National Laboratory’s Advanced Photon Source’s Dynamic Compression Sector operated by Washington State University (DCS), driving a planar shock front through a corrugated Mo-D 2 O or Mo-C 8 F 18 interface, forcing the corrugation to significantly deform. The extent of interfacial deformation, RMI growth, is experimentally observed using X-ray phase contrast imaging at the DCS. RMI jet lengths and jet shapes are extracted from the experimental radiographs, then used to calibrate numerical simulations performed with the Sandia National Laboratories (SNL) hydrocode CTH. Mo yield strength, Y, as a function of shock pressure, P, strain rate, $\dot{\varepsilon }$, accumulated strain, ϵ, relative volumetric compression, RD , and temperature, T , is determined for each impact experiment and presented. The calibrated Mo yield strength values range 1.2–1.8 GPa, with strength generally decreasing as the impact stress increases. This trend is likely caused by thermal softening or strain localization. The tabular yield strength versus loading condition data presented in this paper can be used to fit complex strength models.

Voorhees, T. J. [Sandia National Lab. (SNL-CA), Li↗
DOE OSTI2024

JARVIS-Leaderboard: a large scale benchmark of materials design methods

Abstract Lack of rigorous reproducibility and validation are significant hurdles for scientific development across many fields. Materials science, in particular, encompasses a variety of experimental and theoretical approaches that require careful benchmarking. Leaderboard efforts have been developed previously to mitigate these issues. However, a comprehensive comparison and benchmarking on an integrated platform with multiple data modalities with perfect and defect materials data is still lacking. This work introduces JARVIS-Leaderboard, an open-source and community-driven platform that facilitates benchmarking and enhances reproducibility. The platform allows users to set up benchmarks with custom tasks and enables contributions in the form of dataset, code, and meta-data submissions. We cover the following materials design categories: Artificial Intelligence (AI), Electronic Structure (ES), Force-fields (FF), Quantum Computation (QC), and Experiments (EXP). For AI, we cover several types of input data, including atomic structures, atomistic images, spectra, and text. For ES, we consider multiple ES approaches, software packages, pseudopotentials, materials, and properties, comparing results to experiment. For FF, we compare multiple approaches for material property predictions. For QC, we benchmark Hamiltonian simulations using various quantum algorithms and circuits. Finally, for experiments, we use the inter-laboratory approach to establish benchmarks. There are 1281 contributions to 274 benchmarks using 152 methods with more than 8 million data points, and the leaderboard is continuously expanding. The JARVIS-Leaderboard is available at the website: https://pages.nist.gov/jarvis_leaderboard/

36 MATERIALS SCIENCE↗
DOE OSTI2024

Spin-Controllable Dynamics in Defect-Engineered Carbon Nanotubes as Single Photon Emitters: Data-Driven Modeling and Computations

Quantum technologies, such as quantum computing and sensing, require efficient single-photon emission (SPE) sources that operate at room temperature in telecom wavelengths. While several materials can serve as SPE sources, no single platform meets all the criteria for efficiency, ambient operation, and scalability. Single-walled carbon nanotubes (SWCNTs) with covalently attached molecules offer a promising solution. Their SPE can be easily tuned via modifications of the SWCNT's diameter, chirality, and bonded molecules, enabling emission across near-IR to telecom wavelengths at ambient conditions. However, to fully realize the potential of SWCNTs and unlock their quantum capabilities, a deeper understanding of how structural defects from molecular adducts affect their emission and competing photoexcited processes is essential. To address this gap in our knowledge, this project combined quantum chemistry calculations with data-driven methods of cheminformatics (QSAR) and machine learning (ML). The developed computational approaches have provided several design strategies for covalent functionalization of SWCNTs to improve their optical response. The collaboration with Los Alamos National Lab (LANL) enabled direct comparison of computational and experimental data, facilitating method validation. This partnership was enhanced through access to LANL's Center for Integrated Nanotechnologies (CINT) utilizing User Facility Program and summer internships, which provided three NDSU graduate students with hands-on experience at LANL. The outcomes of this project included (1) Advancing the current stage of computational methods in accurate modeling of non-adiabatic spin-dependent photoexcited dynamics and its applicability to nanosystems consisting of thousands of atoms, realized as open-access codes linked to existing DFT-based software; (2) Establishing the relationship between the structure of adducts and SWCNTs and intrinsic excitonic and spin properties of defect states for guiding novel synthetic strategies and experimental probes of chemically functionalized SWCNTs as near-IR emitting materials; (3) Generating virtual libraries of hypothetical functionalized SWCNTs for virtual screening of their chemical structures and optical properties, leveraging new functionalities of SWCNTs; (4) Offering a unique experience for NDSU graduate students that prepared them for future scientific careers related to materials modeling and big data processing. These results were summarized in 12 published journal papers and 3 recently submitted papers. One of a key finding is that the position of defect sites on the SWCNT surface primarily drives the emission redshift (up to 100 meV), while the polarity of the defect-inducing molecules has a much smaller effect (~10 meV). However, the electron-donating or withdrawing properties of a molecule influence selecting reactivity of defect sites. These insights important for optimizing synthetic protocols for desired emissions in SWCNTs. We also revealed that the interaction between two defects at various positions on the SWCNT enhances the redshift and optical activity of states, favoring strong near-IR emission. This suggests that manipulations in defect concentrations is a promising strategy for controlling efficient emission. Mostly important, the defect position was found controllable by the spin states of photoexcited intermediates: Excited aromatic molecules form ortho defects with SWCNTs at their singlet states in the presence of oxygen, while oxygen-free conditions favor para defects via the triplet-state mechanism. Additionally, a heat-activated [2+2] cycloaddition reaction facilitates divalent defect formation with fewer bonding positions that narrows emission bands. These groundbreaking findings have been experimentally validated and significantly advance our understanding of defect chemistry in SWCNTs. Using a novel encoding technique and 3D-MoRSE descriptors, we developed highly accurate ML/QSAR models to predict both the 3D structure and optical properties of SWCNTs with chemical defects. This model enabled the creation of a virtual library of 125,556 structures, providing new insights into the relationship between SWCNT-defect structure and emission.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Compaction of crushed salt for safe containment – overview of the KOMPASS project

Abstract. In Germany, rock salt formations are possible host rock candidates for a repository for heat-emitting radioactive waste. The safety concept of a repository in salt bases on a multibarrier system consisting mainly of the geological barrier salt and geotechnical seals ensuring safe containment. Crushed salt will be used for backfilling of cavities and sealing measures in drifts and shafts due to its favourable properties and its easy availability (mined-off material). The creep of the rock salt leads to crushed salt compaction with time. Thereby, the crushed salts' porosity is reduced from the initial porosity of 30 %–40 % to a value comparable to the porosity of undisturbed rock salt (≤1 %). In such low porosity ranges, technical impermeability is assumed. The compaction behaviour of crushed salt is rather complex and involves several coupled THM processes (Kröhn et al., 2017; Hansen et al., 2014). It is influenced by internal properties like humidity and grain size distribution, as well as boundary conditions such as temperature, compaction rate or stress state. However, the current process understanding has some important gaps referring to the material behaviour, experimental database and numerical modelling. It needs to be extended and validated, especially in the low porosity range. The objective of the KOMPASS project was development of methods and strategies for the reduction of deficits in the prediction of crushed salt compaction leading to an improvement of the prognosis quality. Key results are as follows (KOMPASS Phase 1, 2020): selection of an easily available and permanently producible synthetic crushed salt mixture, acting as a reference material for generic investigations; development and proof of different techniques for producing pre-compacted samples for further investigations; establishment of a tool of microstructure investigation methods to demonstrate the comparability of grain structures of pre-compacted samples with in-situ compacted material for future investigations; execution of various laboratory experiments using pre-compacted samples, e.g. long-term creep tests which deliver reliable information about time- and stress-dependent compaction behaviour; development of a complex experimental investigation strategy to derive necessary model parameters considering individual functional dependencies. Its technical feasibility was successfully verified; benchmarking with various existing numerical models using datasets from three different triaxial long-term tests. The result was not entirely satisfactory; however, the number of influencing factors is small and further validation work has to be done. Overall, the KOMPASS project has made significant progress in the approaches to solving the outstanding question, building the basis for further investigations.

Friedenberg, Larissa↗
NASA NTRS1992

High heat flux measurements and experimental calibrations/characterizations

Recent progress in techniques employed in the measurement of very high heat-transfer rates in reentry-type facilities at the Arnold Engineering Development Center (AEDC) is described. These advances include thermal analyses applied to transducer concepts used to make these measurements; improved heat-flux sensor fabrication methods, equipment, and procedures for determining the experimental time response of individual sensors; performance of absolute heat-flux calibrations at levels above 2,000 Btu/cu ft-sec (2.27 kW/cu cm); and innovative methods of performing in-situ run-to-run characterizations of heat-flux probes installed in the test facility. Graphical illustrations of the results of extensive thermal analyses of the null-point calorimeter and coaxial surface thermocouple concepts with application to measurements in aerothermal test environments are presented. Results of time response experiments and absolute calibrations of null-point calorimeters and coaxial thermocouples performed in the laboratory at intermediate to high heat-flux levels are shown. Typical AEDC high-enthalpy arc heater heat-flux data recently obtained with a Calspan-fabricated null-point probe model are included.

Kidd, Carl T.↗
DOE OSTI2019

Estimation of full-field dynamic strains from digital video measurements of output-only beam structures by video motion processing and modal superposition

Strain is an necessary quantity to characterize local structural behaviors and directly correlates with structural damage initiation and development that is within local regions. Strain measurement at high spatial resolution (density) locations is thus required to characterize local structural behaviors and detect potential local damage. Traditional contact-type strain gauges are mostly discrete point-wise sensors that can only be placed in a limited number of positions. Distributed optical fiber sensing techniques can measure strains at spatially dense measurement points, but their instrumentation is a time- and labor-intensive process associated with the issue of the fragility of fibers. Noncontact optical measurement techniques, such as a family of interferometry techniques using laser beams (e.g., laser Doppler vibrometers), can provide vibration measurement at high density spatial points without the need to install sensors on the structure. Yet, these measurement devices are active sensing methods that are relatively expensive and vulnerable to ambient motion. Photogrammetry is an alternative noncontact optical measurement method using (passive) white-light imaging of digital video cameras that are relatively low-cost, agile, and provides simultaneous measurements at high spatial density locations where every pixel becomes a measurement point. Among others, digital image correlation can achieve full-field deformation measurements and subsequently estimate the full-field strains. However, it is computationally extensive. This research develops a new efficient approach to estimate the full-field (as many measurement points as the pixel number of the video frame on the structure) dynamic strains at high-spatial (pixel)-resolution/density location points from the digital video measurement of output-only vibrating structures. The developed approach is based on phase-based video motion estimation and modal superposition of structural dynamic response. Moreover, the method is augmented by a high-fidelity finite element model, which is updated with the full-field experimental modal parameters “blindly” identified from the video measurement of the output-only structure. Laboratory experiments are conducted to validate the method on a bench-scale cantilever beam structure. Results demonstrate that the full-field dynamic strain estimated by the developed approach from the video measurement of the output-only vibrating beam match very well those directly measured by the strain gauges (at discrete measurement points). Some factors associated with the effectiveness of the method are experimentally studied and discussed.

47 OTHER INSTRUMENTATION↗
NASA NTRS1988

Application of linear response theory to experimental data of simultaneous radiation and annealing response of a CMOS device

Results from the application of linear response theory are compared to experimental data from simultaneous radiation and annealing response of a CMOS device. In particular, a method is applied which was developed earlier to determine the characteristic time, t(0), as well as the parameters A and C in the 1n(t) dependence of the linear response function R(t) = -C + A1n(1-t/t(0)). The method is based on a study of the linear response for t being much less than t(0), when R(t) can be expanded in a power series of t: R(t) = R(0) + R'(0)t + 1/2R''(0)t-squared + 1/3R'''(0)t-cubed + ..., where R'(0) and R''(0) are, respectively, the first and second derivatives of R with respect to t. To find the linear response, R(t-t') is substituted in the form of this power series equation into a general equation for the shift of the threshold potential. To test the method, irradiation experiments were conducted on RCA 10(6) rad-hard CMOS IC's. A dose rate of approximately 130 rads/min was used. An IC was irradiated with Co-60 gamma rays for several hours, taking measurements of the threshold potential for one n-channel and one p-channel transistor every ten minutes. For the p-channel transistor, t(0) was found to be approximately 110 min and for the n-channel, t(0) was approximately 70 min. For the p-channel, the theoretical curve deviates from the experimental points only after 70 min; for the n-channel, the deviation takes place after 45 min. Additional findings are discussed and the application of the method to pure annealing is described.

Litovchenko, V.↗
DOE OSTI2020

Development of low temperature fuel cell holders for Operando x-ray micro and nano computed tomography to visualize water distribution

Abstract Synchrotron x-ray imaging techniques, like x-ray computed tomography (CT) and radiography have proven instrumental in expanding the communities knowledge of complex transport and reaction kinetics in electrochemical devices such as fuel cells and electrolyzers. This work presents the development of novel x-ray CT imaging techniques for operando visualization of water within low temperature fuel cells at spatial resolutions spanning the micro and nano scales. The design of operando sample holders, for both micro x-ray CT and nano CT experiments is described in depth, and prototypes of these sample holders were evaluated across a set of requirements, the most important of which are x-ray transmissibility, electrical conductivity and mechanical stability. Water segmentation from micro x-ray CT data was enabled by an image subtraction method, where the image without water is subtracted from the one with water. Through iterative experimentations, the operando nano CT cell was developed to optimize mechanical compression, electric conductivity and gas flow. While three-dimensional fuel cell reconstructions were shown possible, there remain challenges to overcome at typical lower energies (8 keV) due to beam damage, whereas it is not as significant for higher energies (>17.5 keV).

Kulkarni, Devashish↗
NASA NTRS1993

Microwave techniques for physical property measurements

Industrial processing of metals and ceramics is now being streamlined by the development of theoretical models. High temperature thermophysical properties of these materials are required to successfully apply these theories. Unfortunately, there is insufficient experimental data available for many of these properties, particularly in the molten state. Microwave fields can be used to measure specific heat, thermal diffusivity, thermal conductivity and dielectric constants at high temperatures. We propose to (1) develop a microwave flash method (analogous to the laser flash technique) that can simultaneously measure the thermal diffusivity and specific heat of insulators and semiconductors at high temperatures, (2) an appropriate theory and experimental apparatus to demonstrate the measurement of the specific heat of a metal using a new microwave ac specific heat technique, and (3) experimental methods for noncontact measurement of the real and imaginary dielectric constants.

Barmatz, M.↗
NASA NTRS1985

Development of seeding techniques for small supersonic wind tunnel

The NASA Lewis 1x1 foot supersonic wind tunnel is used to experimentally verify computational methods. This tunnel, which is continuous running, operates from laboratory-wide high pressure air and vacuum systems. As such, the air does not recirculate but makes a single pass through the tunnel. The Mach number is varied with interchangeable nozzle blocks and has a range from Mach 1.6 to 4.0. Dry and filtered air is available up to pressures of 3 atmospheres. The air enters the tunnel system through a plenum having flow straighteners and 6 fine mesh screens. The exit of the plenum provides smooth contraction with an area ratio of approximately 20 that, along with the screens, provides a uniform flow for the nozzle.

Hingst, W. R.↗
DOE OSTI2018

Next-generation wargames

Over the past century, and particularly since the outset of the Cold War, wargames (interactive simulations used to evaluate aspects of tactics, operations, and strategy) have become an integral means for militaries and policy-makers to evaluate how strategic decisions are made related to nuclear weapons strategy and international security. Furthermore, these methods have also been applied beyond the military realm, to examine phenomena as varied as elections, government policy, international trade, and supply-chain mechanics. Today, a renewed focus on wargaming combined with access to sophisticated and inexpensive drag-and-drop digital game development frameworks and new cloud computing architectures have democratized the ability to enable massive multiplayer gaming experiences. With the integration of simulation tools and experimental methods from a variety of social science disciplines, a science-based experimental gaming approach has the potential to transform the insights generated from gaming by creating human-derived, large-n datasets for replicable, quantitative analysis. In the following, we outline challenges associated with contemporary simulation and wargaming tools, investigate where scholars have searched for game data, and explore the utility of new experimental gaming and data analysis methods in both policy-making and academic settings.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2023

Machine-Learning-Based Rotating Detonation Engine Diagnostics: Evaluation for Application in Experimental Facilities

Real-time monitoring of combustion behavior is a crucial step toward actively controlled rotating detonation engine (RDE) operation in laboratory and industrial environments. Various machine learning methods have been developed to advance diagnostic efficiencies from conventional postprocessing efforts to real-time methods. Here this work evaluates and compares conventional techniques alongside convolutional neural network (CNN) architectures trained in previous studies, including image classification, object detection, and time series classification, according to metrics affecting diagnostic feasibility, external applicability, and performance. Real-time, capable diagnostics are deployed and evaluated using an altered experimental setup. Image-based CNNs are applied to externally provided images to approximate dataset restrictions. Image classification using high-speed chemiluminescence images and time series classification using high-speed flame ionization and pressure measurements achieve classification speeds enabling real-time diagnostic capabilities, averaging laboratory-deployed diagnostic feedback rates of 4–5 Hz. Object detection achieves the most refined resolution of 20 μs in postprocessing. Image and time series classification require the additional correlation of sensor data, extending their time-step resolutions to 80 ms. Comparisons show that no single diagnostic approach outperforms its competitors across all metrics. This finding justifies the need for a machine learning portfolio containing a host of networks to address specific needs throughout the RDE research community.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1989

Numerical and experimental analysis of a thin liquid film on a rotating disk related to development of a spacecraft absorption cooling system

The numerical and experimental analysis of a thin liquid film on a rotating and a stationary disk related to the development of an absorber unit for a high capacity spacecraft absorption cooling system, is described. The creation of artificial gravity by the use of a centrifugal field was focused upon in this report. Areas covered include: (1) One-dimensional computation of thin liquid film flows; (2) Experimental measurement of film height and visualization of flow; (3) Two-dimensional computation of the free surface flow of a thin liquid film using a pressure optimization method; (4) Computation of heat transfer in two-dimensional thin film flow; (5) Development of a new computational methodology for the free surface flows using a permeable wall; (6) Analysis of fluid flow and heat transfer in a thin film in the presence and absence of gravity; and (7) Comparison of theoretical prediction and experimental data. The basic phenomena related to fluid flow and heat transfer on rotating systems reported here can also be applied to other areas of space systems.

Faghri, Amir↗
DOE OSTI2020

Simulating metagenomic stable isotope probing datasets with MetaSIPSim

DNA-stable isotope probing (DNA-SIP) links microorganisms to their in-situ function in diverse environmental samples. Combining DNA-SIP and metagenomics (metagenomic-SIP) allows us to link genomes from complex communities to their specific functions and improves the assembly and binning of these targeted genomes. However, empirical development of metagenomic-SIP methods is hindered by the complexity and cost of these studies. We developed a toolkit, ‘MetaSIPSim,’ to simulate sequencing read libraries for metagenomic-SIP experiments. MetaSIPSim is intended to generate datasets for method development and testing. To this end, we used MetaSIPSim generated data to demonstrate the advantages of metagenomic-SIP over a conventional shotgun metagenomic sequencing experiment. Through simulation we show that metagenomic-SIP improves the assembly and binning of isotopically labeled genomes relative to a conventional metagenomic approach. Improvements were dependent on experimental parameters and on sequencing depth. Community level G + C content impacted the assembly of labeled genomes and subsequent binning, where high community G + C generally reduced the benefits of metagenomic-SIP. Furthermore, when a high proportion of the community is isotopically labeled, the benefits of metagenomic-SIP decline. Finally, the choice of gradient fractions to sequence greatly influences method performance. Metagenomic-SIP is a valuable method for recovering isotopically labeled genomes from complex communities. We show that metagenomic-SIP performance depends on optimization of experimental parameters. MetaSIPSim allows for simulation of metagenomic-SIP datasets which facilitates the optimization and development of metagenomic-SIP experiments and analytical approaches for dealing with these data.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

The Profiled Feldman-Cousins Method for Confidence Interval Construction for the Nova 3-Flavor Oscillation Analysis

The small interaction cross-section of neutrinos makes experimental neutrino physics particularly responsive to technological advancements. A significant development leveraged by the NOvA experiment is large-scale parallel processing, enabling novel computational approaches to longstanding experimental challenges. Central to managing the resulting high-throughput data is NOvA’s implementation of the Freight Train model, designed for efficient data production and handling.This dissertation details the methodology and execution of the NOvA 2024 3-Flavor Oscillation Analysis, supported by a comprehensive dataset spanning ten years. It emphasizes frequentist results refined through the Feldman-Cousins (FC) technique, specifically addressing confidence interval corrections in parameter estimation. The computational intensity associated with Feldman-Cousins arises from extensive Monte Carlo simulations, which were substantially mitigated through parallel computing on the Perlmutter supercomputer at the National Energy Research Scientific Computing Center (NERSC), employing the MPI framework.To further enhance computational efficiency, an Importance Sampling method is introduced and evaluated, demonstrating significant potential to reduce complexity, particularly in exploring extreme parameter space regions. This thesis presents both the successful application of advanced computational resources and the development of sophisticated statistical techniques, aiming to enhance the precision and scope of neutrino oscillation analyses.

Dye ajdye11190@gmail.com, Andrew Joseph [Mississip↗