Search NASA⌕ Search

SEARCH · Search NASA

Results for “Elemental analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Dynamic analysis of elemental mercury released from thermal decomposition of coal

Mercury (Hg) is a toxic and ubiquitous trace element in coal. Monitoring its release behavior during coal processing is a challenging problem. This paper presents a method that is capable of online measurement of the dynamic release behavior of elemental Hg (Hg{sup 0}) from thermal decomposition of coal. The method couples a temperature-programmed decomposition unit with an atomic fluorescence spectrometry detector (TPD-AFS). The AFS signal can be converted to Hg content for quantitative analysis through calibration. The main advantage of the TPD-AFS system is that it can provide either real-time or accumulated data. It was confirmed that the amount of Hg{sup 0} determined by this method agreed well with that by the Ontario-Hydro method, and the results are reproducible with a high accuracy. The method can be used to characterize the release behavior of Hg in coals upon heating and may be used to identify the forms of occurrence of Hg in coals. 16 refs., 4 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Estimation of Low Cycle Fatigue Response of 316 LN Stainless Steel in the Presence of Notch

Notches introduced in the plain specimen result in the multiaxial state of stress that exists in the actual components due to the presence of flaws and defects. In the present work, low cycle fatigue life estimation of plain and notched specimens of 316 LN stainless steel is carried out at room temperature and 823 K. The plain and notched specimens with different notch radii were subjected to varying strain amplitudes ranging from ± 0.25 to ± 1.0% at a strain rate of 3 × 10{sup −3} s{sup −1}. The fatigue life decreased in the presence of notch for all strain amplitudes at both the temperatures. The decrease in fatigue life was found to be more at room temperature than at 823 K. The fatigue life of the notched specimen decreased by approximately 94.2% compared to plain specimen at room temperature. However, at 823 K the decrease in fatigue life for notched specimen was approximately 84.6%. Low cycle fatigue life of the plain and notched specimens was estimated by Neuber’s rule and finite element analysis approach. Neuber’s rule overestimated the fatigue life by maximum factor of 2.6 for specimens at room temperature and by maximum factor of 5 for specimens at 823 K. However, it gives closer approximation at higher strain amplitudes at 823 K. Life estimation by finite element analysis at room temperature was within a factor of 1.5 as compared to experimental life, whereas it underestimated the fatigue life within a factor of 6 at high temperature.

36 MATERIALS SCIENCE↗

Development of fiber-based laser anemometer for SSME application

A recent study by Rocketdyne for NASA identified laser anemometry, using a compact optical head, as a feasible diagnostic instrument for the Space Shuttle Main Engine (SSME) Model Verification experiments. Physical Research, Inc. (PRI) is presently under contract from NASA Lewis to develop and deliver such a laser anemometer system. For this application, it is desired to place the laser at a remote distance from the engine, and use single mode polarization preserving fiber optics for the transmission of the laser light to and from the measurement head. Other requirements are given. Analytical and experimental tools are being used to develop the technologies required for the laser anemometer. These include finite element analysis of the optical head and vibration tests for various optical and mechanical components. Design of the optical head and the fiber optic connectors are driven by the temperature and vibration requirements for the measurement environment. Results of the finite element analysis and the vibration tests of the components are included. Conceptual design of the fiber optic launcher and the optical probe has also been complete. Detailed design of the probe as well as the fabrication and assembly of the components is in progress.

Modarress, Dariush↗

Study of thermal stability and degradation of fire resistant candidate polymers for aircraft interiors

The thermochemistry of bismaleimide resins and phenolphthalein polycarbonate was studied. Both materials are fire-resistant polymers and may be suitable for aircraft interiors. The chemical composition of the polymers has been determined by nuclear magnetic resonance and infrared spectroscopy and by elemental analysis. Thermal properties of these polymers have been characterized by thermogravimetric analyses. Qualitative evaluation of the volatile products formed in pyrolysis under oxidative and non-oxidative conditions has been made using infrared spectrometry. The residues after pyrolysis were analyzed by elemental analysis. The thermal stability of composite panel and thermoplastic materials for aircraft interiors was studied by thermogravimetric analyses.

Hsu, M. T. S.↗

In Situ Characterization of Boehmite Particles in Water Using Liquid SEM

In situ imaging and elemental analysis of boehmite (AlOOH) particles in water is realized using the System for Analysis at the Liquid Vacuum Interface (SALVI) and Scanning Electron Microscopy (SEM). This paper describes the method and key steps in integrating the vacuum compatible SAVLI to SEM and obtaining secondary electron (SE) images of particles in liquid in high vacuum. Energy dispersive x-ray spectroscopy (EDX) is used to obtain elemental analysis of particles in liquid. A synthesized AlOOH particle is used as a model in the liquid SEM illustration. Our results demonstrate that particles can be imaged in the SE mode with good resolution. The AlOOH EDX spectrum shows significant signal from the Al compared with deionized water and the empty channel control. In situ liquid SEM is a powerful technique to study particles in liquid with many exciting applications. This procedure aims to provide technical details in how to conduct liquid SEM imaging and EDX analysis using SALVI and reduce potential pitfalls using this approach for other researchers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Poromechanical cohesive interface element with combined Mode I-II cohesive zone elastoplasticity for simulating fracture in fluid-saturated porous media

A combined Mode I-II cohesive zone (CZ) elasto-plastic constitutive model, and a two-dimensional (2D) cohesive interface element (CIE) are formulated and implemented at small strain within an ABAQUS User Element (UEL) for simulating 2D crack nucleation and propagation in fluid-saturated porous media. Here, the CZ model mitigates problems of convergence for the global Newton-Raphson solver within ABAQUS, which when combined with a viscous stabilization procedure allows for simulation of post-peak response under load control for coupled poromechanical finite element analysis, such as concrete gravity dam stability analysis. Verification examples are presented, along with a more complex ambient limestone-concrete wedge fracture experiment, water-pressurized concrete wedge experiment, and concrete gravity dam stability analyses. A calibration procedure for estimating the CZ parameters is demonstrated with the limestone-concrete wedge fracture process. For the water-pressurized concrete wedge fracture experiment it is shown that the inherent time-dependence of the poromechanical CIE analysis provides a good match with experimental force versus displacement results at various crack mouth opening rates, yet misses the pore water pressure evolution ahead of the crack tip propagation. This is likely a result of the concrete being partially-saturated in the experiment, whereas the finite element analysis assumes fully water saturated concrete. For the concrete gravity dam analysis, it is shown that base crack opening and associated water uplift pressure leads to a reduced Factor of Safety, which is confirmed by separate analytical calculations.

97 MATHEMATICS AND COMPUTING↗

Improved Synthesis of [Si6Cl14]2-Salts as Precursors for Si6H12and other Novel Silanes

The reaction of excess HSiCl{sub 3} with the aforementioned triamines led to the formation of [Si{sub 6}Cl{sub 14}]{sup 2-} containing salts in all instances. The isolated complex salts were characterized using FT-IR and elemental analysis. IR spectra of these compounds showed characteristic Si-H stretching modes around 2100cm{sup -1} due to the hexacoordinate silane cation and Si-Cl active modes near 528cm{sup -1} as a result of the cyclic dianion. Reaction yields and elemental analysis (CHN) of the salts are summarized in a table. The reaction of peralkylated triamines with HSiCl{sub 3} in dry CH{sub 2}Cl{sub 2} gives ionic compounds based upon the tetradecachlorocyclohexasilane dianion. Several substituted triamines(R{sub 2}NC{sub 2}H{sub 4}NR{prime}C{sub 2}H{sub 4}NR{sub 2}where R = R{prime} = Et, {sup n}Pr; R = Et, R{prime}= {sup n}Bu, {sup n}Hexyl, Benzyl) were examined for this reaction and N,N,N{prime},N{prime}-tetraethyl-N{sup {double_prime}}-benzyl-diethylenetriamine produced the best yields of [Si{sub 6}Cl{sub 14}]{sup 2-} salt at 23% based on the amine reagent. This improvement in yield could be attributed to the decreased nucleophilicity of the central amine through increased steric hindrance of the alkyl substituents. The overall consequence of this substituent variation study has revealed new reagents for the synthesis of [Si{sub 6}Cl{sub 14}]{sup 2-} salts and further demonstrated the ability of triamines to efficiently dismutate, complex, and condense chlorosilanes. The increased production of these salts has also opened a route for the study of Si{sub 6}X{sub 12} and its Lewis acid/base adducts.

14 SOLAR ENERGY↗

Effects of O{sub 2} and SO{sub 2} on the Capture Capacity of a Primary-Amine Based Polymeric CO{sub 2} Sorbent

Post combustion CO{sub 2} capture is most commonly carried out using an amine solution that results in a high parasitic energy cost in the stripper unit due to the need to heat the water which comprises a majority of the amine solution. It is also well known that amine solvents suffer from stability issues due to amine leaching and poisoning by flue gas impurities. Solid sorbents provide an alternative to solvent systems that would potentially reduce the energy penalty of carbon capture. However, the cost of using a particular sorbent is greatly affected by the usable lifetime of the sorbent. This work investigated the stability of a primary amine-functionalized ion exchange resin in the presence of O{sub 2} and SO{sub 2}, both of which are constituents of flue gas that have been shown to cause degradation of various amines in solvent processes. The CO{sub 2} capture capacity was measured over multiple capture cycles under continuous exposure to two simulated flue gas streams, one containing 12 vol% CO{sub 2}, 4% O{sub 2}, 84% N{sub 2}, and the other containing 12.5 vol% CO{sub 2}, 4% O{sub 2}, 431 ppm SO{sub 2}, balance N{sub 2} using a custom-built packed bed reactor. The resin maintained its CO{sub 2} capture capacity of 1.31 mol/kg over 17 capture cycles in the presence of O{sub 2} without SO{sub 2}. However, the CO{sub 2} capture capacity of the resin decreased rapidly under exposure to SO{sub 2} by an amount of 1.3 mol/kg over 9 capture cycles. Elemental analysis revealed the resin adsorbed 1.0 mol/kg of SO{sub 2}. Thermal regeneration was determined to not be possible. The poisoned resin was, however, partially regenerated with exposure to 1.5M NaOH for 3 days resulting in a 43% removal of sulfur, determined through elemental analysis, and a 35% recovery of CO{sub 2} capture capacity. Evidence was also found for amine loss upon prolonged (7 days) continuous exposure to high temperatures (120 C) in air. It is concluded that desulfurization of the flue gas stream prior to CO{sub 2} capture will greatly improve the economic viability of using this solid sorbent in a post-combustion CO{sub 2} capture process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An Initial Electric Motor Rotor Vibration Model

Ongoing integration of outrunner brushless electric motors into drones and Advanced Air Mobility aircraft presents a need for accurate acoustic predictions derived from prediction of the motor rotor vibrations. In outrunner motors, the external rotor vibrates and drives the acoustic field. At resonant frequencies of the rotor, the rotor displacements will be the largest. The vibrations can lead to acoustic tones that are relevant to the overall acoustic design of these types of vehicles. This study performs a finite element analysis to assess the modes in two electric motor rotors. This model is then refined into a simple parameterized geometry that can make the same predictions for motors of the same class. A parametric sweep and least-squares-curve fit to the finite element analysis data results in a series of simple curves that can predict the mode shapes and frequencies that are likely to appear in this class of motors without the need for any simulation. The simulations are validated by comparison to acoustic and experimental modal-analysis data.

Electric Motor Noise↗

An Initial Electric Motor Rotor Vibration Model

Ongoing integration of outrunner brushless electric motors into drones and Advanced Air Mobility aircraft presents a need for accurate acoustic predictions derived from prediction of the motor rotor vibrations. In outrunner motors, the external rotor vibrates and drives the acoustic field. At resonant frequencies of the rotor, the rotor displacements will be the largest. The vibrations can lead to acoustic tones that are relevant to the overall acoustic design of these types of vehicles. This study performs a finite element analysis to assess the modes in two electric motor rotors. This model is then refined into a simple parameterized geometry that can make the same predictions for motors of the same class. A parametric sweep and least-squares-curve fit to the finite element analysis data results in a series of simple curves that can predict the mode shapes and frequencies that are likely to appear in this class of motors without the need for any simulation. The simulations are validated by comparison to acoustic and experimental modal-analysis data.

Electric Motor Noise↗

Structural Stability of a Stiffened Aluminum Fuselage Panel Subjected to Combined Mechanical and Internal Pressure Loads

Results from an experimental and analytical study of a curved stiffened aluminum panel subjected to combined mechanical and internal pressure loads are presented. The panel loading conditions were simulated using a D-box test fixture. Analytical buckling load results calculated from a finite element analysis are presented and compared to experimental results. Buckling results presented indicate that the buckling load of the fuselage panel is significantly influenced by internal pressure loading. The experimental results suggest that the stress distribution is uniform in the panel prior to buckling. Nonlinear finite element analysis results correlates well with experimental results up to buckling.

Rouse, Marshall↗

Minimizing thickness variation in monolithic U-10Mo fuel foil and Zr interlayer during hot rolling: A microstructure-based finite element method analysis

Low-enriched uranium alloyed with 10 wt. % molybdenum (U-10Mo) has been identified as a promising alternative to highly enriched uranium fuel for the United States’ high performance research reactors. The monolithic U-10Mo fuel plate consists of a metallic U-10Mo fuel foil with a 25 µm Zr interlayer and a relatively thick cladding of aluminum alloy 6061. The Zr interlayer is typically applied during the hot co-rolling process, and this process dictates the uniformity of the Zr interlayer. Thickness variation observed in the U-10Mo and Zr interlayer has been attributed to several sources: the initial grain size of the U-10Mo castings, can materials, rolling temperature, inhomogeneous molybdenum content, and porosity in the cast U-10Mo. This thickness variation limits the ability to meet the dimensional specification; thus, a better understanding of the factors causing the nonuniform thickness is needed. In this work, we used a novel, microstructure-based finite element method to model the hot rolling process to address these concerns. Grain microstructures in U-10Mo were tessellated and explicitly considered in the finite element model. Each grain was assigned a random material property to mimic the grain strength variations induced by different grain orientations. Simulations were performed using six steel can thicknesses, four grain sizes, and with or without a Zr interlayer to investigate the influences of those variables on the thickness nonuniformity. The simulation results showed that a thinner steel can and finer U-10Mo grain size reduce thickness variations in both the U-10Mo fuel foil and Zr interlayer. The direct findings from the simulations and analysis can be used to optimize the hot rolling schedule, reduce fabrication defects, and meet the dimensional specifications. The proposed microstructure-based finite element model can be also coupled with experimental microstructure characterization data, images, and models to simulate multi-pass hot rolling.

36 MATERIALS SCIENCE↗

Partitioning strategy for efficient nonlinear finite element dynamic analysis on multiprocessor computers

A computational procedure is presented for the nonlinear dynamic analysis of unsymmetric structures on vector multiprocessor systems. The procedure is based on a novel hierarchical partitioning strategy in which the response of the unsymmetric and antisymmetric response vectors (modes), each obtained by using only a fraction of the degrees of freedom of the original finite element model. The three key elements of the procedure which result in high degree of concurrency throughout the solution process are: (1) mixed (or primitive variable) formulation with independent shape functions for the different fields; (2) operator splitting or restructuring of the discrete equations at each time step to delineate the symmetric and antisymmetric vectors constituting the response; and (3) two level iterative process for generating the response of the structure. An assessment is made of the effectiveness of the procedure on the CRAY X-MP/4 computers.

Noor, Ahmed K.↗

A partitioning strategy for efficient nonlinear finite element dynamic analysis on multiprocessor computer

A computational procedure is presented for the nonlinear dynamic analysis of unsymmetric structures on vector multiprocessor systems. The procedure is based on a novel hierarchical partitioning strategy in which the response of the unsymmetric and antisymmetric response vectors (modes), each obtained by using only a fraction of the degrees of freedom of the original finite element model. The three key elements of the procedure which result in high degree of concurrency throughout the solution process are: (1) mixed (or primitive variable) formulation with independent shape functions for the different fields; (2) operator splitting or restructuring of the discrete equations at each time step to delineate the symmetric and antisymmetric vectors constituting the response; and (3) two level iterative process for generating the response of the structure. An assessment is made of the effectiveness of the procedure on the CRAY X-MP/4 computers.

Noor, Ahmed K.↗

Mechanically fastened composite laminates subjected to combined bearing-bypass and shear loading

Bolts and rivets provide a means of load transfer in the construction of aircraft. However, they give rise to stress concentrations and are often the source and location of static and fatigue failures. Furthermore, fastener holes are prone to cracks during take-off and landing. These cracks present the most common origin of structural failures in aircraft. Therefore, accurate determination of the contact stresses associated with such loaded holes in mechanically fastened joints is essential to reliable strength evaluation and failure prediction. As the laminate is subjected to loading, the contact region, whose extent is not known, develops between the fastener and the hole boundary through this contact region, which consists of slip and no-slip zones due to friction. The presence of the unknown contact stress distribution over the contact region between the pin and the composite laminate, material anisotropy, friction between the pin and the laminate, pin-hole clearance, combined bearing-bypass and shear loading, and finite geometry of the laminate result in a complex non-linear problem. In the case of bearing-bypass loading in compression, this non-linear problem is further complicated by the presence of dual contact regions. Previous research concerning the analysis of mechanical joints subjected to combined bearing-bypass and shear loading is non-existent. In the case of bearing-bypass loading only, except for the study conducted by Naik and Crews (1991), others employed the concept of superposition which is not valid for this non-linear problem. Naik and Crews applied a linear finite element analysis with conditions along the pin-hole contact region specified as displacement constraint equations. The major shortcoming of this method is that the variation of the contract region as a function of the applied load should be known a priori. Also, their analysis is limited to symmetric geometry and material systems, and frictionless boundary conditions. Since the contact stress distribution and the contact region are not known a priori, they did not directly impose the boundary conditions appropriate for modelling the contact and on-contact regions between the fastener and the hole. Furthermore, finite element analysis is not suitable for iterative design calculations for optimizing laminate construction in the presence of fasteners under complex loading conditions. In this study, the solution method developed by Madenci and Ileri (1992a,b) has been extended to determine the contact stresses in mechanical joints under combined bearing-bypass and shear loading, and bearing-bypass loading in compression resulting in dual contact regions.

Madenci, Erdogan↗

Analysis of Triangular Rollable and Collapsible (TRAC) Composite Booms under the Effects of Gravity and Twist

Finite element analysis is used to investigate Triangular Rollable and Collapsible (TRAC) composite booms. The TRAC booms are subjected to a suite of loading conditions, including in-plane bending, out-of-plane bending, and axial compression. Simulations containing as-designed boom geometry are performed, as are simulations with geometric deviations associated with the as-built conditions of a sample TRAC boom. Namely, a cross-sectional twist along the length of the boom is incorporated into the analysis to study the effect of the twist on the deformation characteristics of the boom. Twisting in the sample boom was observed after short-term storage in a rolled configuration and may be attributed to differential creep deformation between the inner and outer flanges of the TRAC boom. Simulations are conducted with and without the effects of gravity to understand the significance of gravity on testing conditions. Booms of three lengths are evaluated: 3 meters, 7.5 meters and 30 meters. The mechanical responses of the TRAC booms are discussed with reference to the effects of gravity, boom length and cross-sectional twisting. Gravity is found to have a more significant effect on boom mechanical response as boom length is increased. Cross-sectional twisting is found to have a more significant effect on boom mechanical response in the shorter booms.

High-strain composites↗

Analysis and test of a space truss foldable hinge

The Mini-Mast is a 20-meter long deployable, three-longeron, truss-beam being used to develop analytical and experimental methods for predicting the physical behavior of large space structures. With 57 corner-body hinges and 54 mid-body hinges, the Mini-Mast is highly joint-dominated, necessitating inclusion of the compliance of the joints in analytical models. This study demonstrates an approach for calculating the stiffness properties of a complicated hinge called the mid-body hinge. The process includes detailed modeling with solid-body modeling software and the use of finite element analysis. Load-deflection tests were conducted to determine the axial stiffness of the mid-body hinge. This is compared to the axial stiffness value determined from a finite element analysis.

Nimmo, N. A.↗

FOAM DENSITY SENSITIVITY STUDY FOR THE 9977 PACKAGE

Two layers of insulation fill the volume of the 9977 package between the drum liner and the shell. One of these layers is composed of General Plastics FR-3716 polyurethane foam (also known as Last-A-Foam{reg_sign}), poured through fill holes in the drum bottom and foamed in place. There was concern that the density of the foam insulating layer may vary due to the manufacturing process and that variations in foam density would compromise the safety basis of the package. Thus, a structural finite element analysis was performed to investigate this concern. The investigation examined the effect of replacing the material properties for the FR-3716 polyurethane foam, which has a density equal to 16 lb{sub m}/ft{sup 3}, with material properties of similar foam with varying densities through finite element analysis of hypothetical accident conditions (HAC) pertaining to impact conditions. The results showed that the functional performance of the containment vessel (CV) was not compromised under the conditions investigated.

36 MATERIALS SCIENCE↗