Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASMA ARC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Development of the VOLT-A Shuttle experiment

The NASA Lewis Research Center (LeRC) is investigating potential problems associated with the operation of high voltage solar cell arrays in the space plasma environment. At high voltages, interactions between the solar array and the space plasma could result in unacceptable levels of electrical discharge (arcing) and/or parasitic losses (current drains from the array to the plasma). The objective of the Voltage Operating Limit Tests (VOLT-A) Shuttle bay experiment is to characterize space plasma/solar cell panel interactions in low earth orbit. VOLT-A consists of an experiment plate subassembly which contains four solar panels, an electronics subassembly and a Langmuir probe subassembly mounted on an MPESS carrier. During a given 8.25 hour data taking period (5-1/2 continuous orbits), the solar panels, which represent state-of-the-art solar cell technologies, will be sequentially subjected to bias voltages in steps ranging from minus 626 V to plus 313 V. Appropriate measurements will be made at each voltage to characterize arcing and parasitic losses. Corresponding measurements of the plasma environment (plasma density, electron temperature and neutral density) will also be made. Data will be recorded on an on-board tape recorder for subsequent data reduction and analysis.

Bifano, William J.↗

Floating Potential Probe Deployed on the International Space Station

In the spring and summer of 2000, at the request of the International Space Station (ISS) Program Office, a Plasma Contactor Unit Tiger Team was set up to investigate the threat of the ISS arcing in the event of a plasma contactor outage. Modeling and ground tests done under that effort showed that it is possible for the external structure of the ISS to become electrically charged to as much as -160 V under some conditions. Much of this work was done in anticipation of the deployment of the first large ISS solar array in November 2000. It was recognized that, with this deployment, the power system would be energized to its full voltage and that the predicted charging would pose an immediate threat to crewmembers involved in extravehicular activities (EVA's), as well as long-term damage to the station structure, were the ISS plasma contactors to be turned off or stop functioning. The Floating Potential Probe was conceived, designed, built, and deployed in record time by a crack team of scientists and engineers led by the NASA Glenn Research Center in response to ISS concerns about crew safety.

Ferguson, Dale C.↗

Pulsed Electron Source with Grid Plasma Cathode and Longitudinal Magnetic Field for Modification of Material and Product Surfaces

The description and the main characteristics of the pulsed electron source “SOLO” developed on the basis of the plasma cathode with grid stabilization of the emission plasma boundary are presented. Тhe emission plasma is generated by a low-pressure arc discharge, and that allows to form the dense low-energy electron beam with a wide range of independently adjustable parameters of beam current pulses (pulse duration of 20–250 μs, pulse repetition rate of 1–10 s{sup –1}, amplitude of beam current pulses of 20–300 A, and energy of beam electrons of 5–25 keV). Тhe special features of generation of emission plasma by constricted low-pressure arc discharge in the grid plasma cathode partially dipped into a non-uniform magnetic field and of formation and transportation of the electron beam in a longitudinal magnetic field are considered. The application area of the electron source and technologies realized with its help are specified.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Problem of RF Gradient Limits

We describe breakdown in rf accelerator cavities in terms of a number of mechanisms. We divide the breakdown process into three stages: 1) we model surface failure using molecular dynamics of fracture caused by electrostatic tensile stress, 2) the ionization and plasma growth is modeled using a particle in cell code, 3) we model surface damage by assuming unipolar arcing. Although unipolar arcs are strictly defined with equipotential boundaries, we find that the cold, dense plasma in contact with the surface produces very small Debye lengths and very high electric fields over a large area, and these high fields produce strong erosion mechanisms, primarily self sputtering, compatible with crater formation. We compare this model with arcs in tokamaks, plasma ablation, electron beam welding, micrometeorite impacts, and other examples.

43 PARTICLE ACCELERATORS↗

The role of unneutralized surface ions in negative potential arcing

The observed arcing on negatively biased solar arrays exposed to plasma environments is shown to be due to an effective charge layer on the interconnect formed by ion collection from the plasma. Time scales to form this layer are shown to be in agreement with experimental observations. A quantitative theory is presented which predicts arcing threshold dependence on plasma density and external potentials. After breakdown, the discharge process is modeled as space charge limited transport to nearby coverslips. Peak currents and decay times predicted by this model are compared with experimental observations.

Jongeward, G. A.↗

Filamentary structures in the magnetotail lobes

The observations of plasmas which may be the source population for polar cap arcs are reported. This population consists of energetic plasma contained within filamentary structures aligned approximately parallel to the XZ plane. Using a combination of plasma, particle, and magnetic field data for several events, it is established that the filaments have their origin in the plasma sheet or its adjacent boundary layer, and that the structures protrude into the lobe region. In a number of cases, a correlation between the convection pattern and the IMF B(Z) can be inferred. This is in agreement with the observed characteristics of polar cap arcs, observations of which are correlated with a northward directed IMF. The presence of field-aligned currents suggests that field-aligned acceleration may occur between the observing satellite and earth.

Huang, C. Y.↗

Pulsed anodic arc discharge for the synthesis of carbon nanomaterials

Pulsed arc discharges can improve arc control and tailor the ablation process in the production of 1D and 2D nanostructures from carbon anodes. In this work, low-dimensional carbon nanoparticles have been generated by means of anodic arc discharge in helium atmosphere excited with a square-wave modulated signal (1–5 Hz, 10% duty cycle). The discharges were performed between two graphite electrodes with maximal peak current of 250 A and maximal voltage of 65 V. The erosion rates and conversion efficiency of the ablated anode are compared to reference samples grown in DC steady arc mode. Ablation rates in pulsed arcs are typically of the order of 1 mg/s. Combination of fast Langmuir probe diagnostics and optical emission spectroscopy provided plasma parameters of the discharges at the arc column. Ranges of 10 16 –10 17 m -3 for electron density and 0.5–2.0 eV for electron temperature are estimated. The obtained samples were characterized with Raman spectroscopy and scanning electron microscopy. The deposit on the cathode after pulsed arc consisted of carbon nanostructures such as graphene nano-platelets and carbon nanotubes. Erosion dynamics of pulsed arc discharge has been described in terms of a global model and compared to steady arc discharge. A correlation is identified among discharge regimes, optical emission patterns and ablation modes. In conclusion, pulsed anodic arc discharge is a very efficient source of carbon nanomaterials. The large control of the discharge characteristics will permit to tailor accurately the production and the properties of carbon nanotubes and graphene. Here, this deposition method is promising for the fabrication of semiconducting nanomaterials with tuneable electrical and optical properties.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurement of Temperature and Density Profiles of the Plasma at PR-2 Facility

A new system of probe diagnostics at linear plasma simulator PR-2 is described, allowing us to measure the profiles of plasma temperature and density in different cross sections of the plasma column. The Langmuir probe fixed to the movable part of the two-coordinate positioning system built into the PR-2 passes the region of the discharge area during the process of measuring plasma parameters. The overall dimensions of the positioning system make it possible to mount electrical probes (magnetic probes, optical fibers, and other diagnostic equipment) covering almost the entire volume of the vacuum chamber between the magnetic mirrors of the device. We present the measurement results of local plasma parameters of the beam-plasma discharge (BPD) for different values of the input power and working gas pressure. The boundaries of appearance of discharge of three types were determined: the diffusive BPD mode, the BPD mode, and the arc mode. Dependences of the plasma concentration and temperature on the input power for different values of pressure have been also determined.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigation of a Gallium MPD Thruster with an Ablating Cathode

Arc impedance, exhaust velocity, and plasma probe measurements are presented. The thruster is driven by a 50 microsecond pulse from a 6.2 milliohm pulse forming network, and gallium is supplied to the discharge by evaporation of the cathode. The arc voltage is found to vary linearly with the discharge current with an arc impedance of 6.5 milliohms. Electrostatic probes yield an exhaust velocity that is invariant with the discharge current and has a peak value of 20 kilometers per second, which is in reasonable agreement with the value (16 plus or minus 1 kilometer per second) calculated from the mass bit and discharge current data. Triple probe measurements yield on axis electron temperatures in the range of 0.8-3.8 eV, electron densities in the range of 1.6 x 10(exp 21) to 2.1 x 10(exp 22) per cubic meter, and a divergence half angle of 16 degrees. Measurements within the interelectrode region yield a peak magnetic field of 0.8 T, and the observed radial trends are consistent with an azimuthally symmetric current distribution. A cathode power balance model is coupled with an ablative heat conduction model predicting mass bit values that are within 20% of the experimental values.

Thomas, Robert E.↗

Adaptive materials processing

New sensors for both arc welding and resistance spot welding processes were studied. For arc welding, the arc itself is used as the sensor. Minor changes in both composition and geometry of the plasma result in fluctuations in the arc voltage. While the process as currently employed is an off-line system, development of an on-line process controller would be possible once the optimum analysis technique is developed. It has been shown that for resistance spot welding, the dynamic resistance of the weld joint can be correlated to growth of the fusion zone. It is indicated that this technique is not as useful for projection welds as for spot welds.

Eager, T. W.↗

Comparative Measurements of Earth and Martian Entry Environments in the NASA Langley HYMETS Facility

Arc-jet facilities play a major role in the development of heat shield materials for entry vehicles because they are capable of producing representative high-enthalpy flow environments. Arc-jet test data is used to certify material performance for a particular mission and to validate or calibrate models of material response during atmospheric entry. Materials used on missions entering Earth s atmosphere are certified in an arc-jet using a simulated air entry environment. Materials used on missions entering the Martian atmosphere should be certified in an arc-jet using a simulated Martian atmosphere entry environment, which requires the use of carbon dioxide. Carbon dioxide has not been used as a test gas in a United States arc-jet facility since the early 1970 s during the certification of materials for the Viking Missions. Materials certified for the Viking missions have been used on every entry mission to Mars since that time. The use of carbon dioxide as a test gas in an arc-jet is again of interest to the thermal protection system community for certification of new heat shield materials that can increase the landed mass capability for Mars bound missions beyond that of Viking and Pathfinder. This paper describes the modification, operation, and performance of the Hypersonic Materials Environmental Test System (HYMETS) arc-jet facility with carbon dioxide as a test gas. A basic comparison of heat fluxes, various bulk properties, and performance characteristics for various Earth and Martian entry environments in HYMETS is provided. The Earth and Martian entry environments consist of a standard Earth atmosphere, an oxygen-rich Earth atmosphere, and a simulated Martian atmosphere. Finally, a preliminary comparison of the HYMETS arc-jet facility to several European plasma facilities is made to place the HYMETS facility in a more global context of arc-jet testing capability.

Splinter, Scott C.↗

A mathematical model of the structure and evolution of small scale discrete auroral arcs

A three dimensional fluid model which includes the dispersive effect of electron inertia is used to study the nonlinear macroscopic plasma dynamics of small scale discrete auroral arcs within the auroral acceleration zone and ionosphere. The motion of the Alfven wave source relative to the magnetospheric and ionospheric plasma forms an oblique Alfven wave which is reflected from the topside ionosphere by the negative density gradient. The superposition of the incident and reflected wave can be described by a steady state analytical solution of the model equations with the appropriate boundary conditions. This two dimensional discrete auroral arc equilibrium provides a simple explanation of auroral acceleration associated with the parallel electric field. Three dimensional fully nonlinear numerical simulations indicate that the equilibrium arc configuration evolves three dimensionally through collisionless tearing and reconnection of the current layer. The interaction of the perturbed flow and the transverse magnetic field produces complex transverse structure that may be the origin of the folds and curls observed to be associated with small scale discrete arcs.

Seyler, C. E.↗

Experimental studies of the arc chamber short circuit failure mechanism on the DIII-D neutral beam system

Here we report on efforts to improve performance and longevity of the Neutral Beam Injection (NBI) system by initiating a R&D program aimed at studying the most common failure mechanism for the ion sources. To this end a filament driven plasma chamber has been constructed with plasma parameters similar to the arc chamber of NBI ion sources. A preliminary report of an investigation into the most common failure is presented here: The failure mechanism observed during helium operations on DIII-D is the result of electrical breakdown of the insulation material that separates the filament plates from the anode. The fault is reproduced in a table top experiment analogous to the DIII-D NBI ion source in key parameters and proposals for amelioration of the issue are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Photovoltaic Plasma Interaction Test 2

The International Space Station (ISS) program is developing a plasma contactor to mitigate the harmful effects of charge collection on the station's large photovoltaic arrays. The purpose of the present test was to examine the effects of charge collection on the solar array electrical circuit and to verify the effectiveness of the plasma contactor. The results showed that the plasma contactor was able to eliminate structure arcing for any array output voltage. However, the current requirements of the plasma contactor were higher than those for prior testing and predicted by analysis. Three possible causes for this excess current demand are discussed. The most likely appeared to be a high local pressure on or very near the surface of the array as a result of vacuum tank conditions. Therefore, in actual space conditions, the plasma contactor should work as predicted.

Kaufman, Bradford A.↗

Scaling and applied field studies of MPD thrusters with laser diagnostics

The topics are presented in viewgraph form and include the following: self-field magnetoplasmadynamics; 1/4-scale applied-field MPD; scaling of arcs and MPD-arcs; magnetic nozzle studies; advanced diagnostic techniques needed for obtaining particle velocity, temperature, and current distributions in plasma thrusters; nonintrusive laser diagnostics for arcs and MPD-arcs; and schematic of multi-beam interferometer for electron density profile determination.

York, Thomas M.↗

Spectrographic temperature measurement of a high power breakdown arc in a high pressure gas switch

A procedure for obtaining an approximate temperature value of conducting plasma generated during self-break closure of a RIMFIRE gas switch is described. The plasma is in the form of a breakdown arc which conducts approximately 12 kJ of energy in 1 {mu}s. A spectrographic analysis of the trigger-section of the 6-MV RIMFIRE laser triggered gas switch used in Sandia National Laboratory's ''Z-Machine'' has been made. It is assumed that the breakdown plasma has sufficiently approached local thermodynamic equilibrium allowing a black-body temperature model to be applied. This model allows the plasma temperature and radiated power to be approximated. The gas dielectric used in these tests was pressurized SF{sub 6}. The electrode gap is set at 4.59 cm for each test. The electrode material is stainless steel and insulator material is poly(methyl methacrylate). A spectrum range from 220 to 550 nanometers has been observed and calibrated using two spectral irradiance lamps and three spectrograph gratings. The approximate plasma temperature is reported.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

High-frequency waves generated by auroral electrons

Measurements of marginally unstable electron distribution functions and high-frequency plasma waves were made on a sounding rocket flight through a quiet auroral arc. The waves appeared near the electron plasma frequency and had a large parallel electric field component such that k-parallel is greater than k-perpendicular. The appearance of these waves was correlated with the presence of marginally unstable parallel electron distributions. Analysis has shown that the waves were produced by parallel electron distribution function greater than 0 rather than the small perpendicular electron distribution function greater than 0 features. Wave levels and growth rates inside the arc were small, and nonlinear wave-wave and wave-particle interactions appear to have been minimal.

Mcfadden, J. P.↗