Search NASA⌕ Search

SEARCH · Search NASA

Results for “Frequency estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Kinetics of crystal nucleation and growth in Pd(40)Ni(40)P(20) glass

Samples of Pd(40)Ni(40)P(20) glass, produced by cooling the melt at 1 or 800 K/s, are heated in a differential scanning calorimeter to determine the crystallization kinetics. Optical microscopy shows that eutectic crystallization proceeds both by growth from the surface of the samples and by the growth of spherical regions around preexisting nuclei in the interior. A modified Kissinger (1957) analysis is used to obtain the activation energy for crystal growth (3.49 eV). The steady state homogeneous nucleation frequency at 590 K is about 10 million/cu m per sec. This is estimated to be the maximum nucleation frequency: it is too low to account for the observed population of quenched-in nuclei, which are therefore presumed to be heterogeneous. The major practical obstacle to glass formation in this system is heterogeneous nucleation.

Drehman, A. J.↗

Spectral moment estimation in MST radars

Signal processing techniques used in Mesosphere-Stratosphere-Troposphere (MST) radars are reviewed. Techniques which produce good estimates of the total power, frequency shift, and spectral width of the radar power spectra are considered. Non-linear curve fitting, autocovariance, autocorrelation, covariance, and maximum likelihood estimators are discussed.

Woodman, R. F.↗

Ball bearing vibrations amplitude modeling and test comparisons

Bearings generate disturbances that, when combined with structural gains of a momentum wheel, contribute to induced vibration in the wheel. The frequencies generated by a ball bearing are defined by the bearing's geometry and defects. The amplitudes at these frequencies are dependent upon the actual geometry variations from perfection; therefore, a geometrically perfect bearing will produce no amplitudes at the kinematic frequencies that the design generates. Because perfect geometry can only be approached, emitted vibrations do occur. The most significant vibration is at the spin frequency and can be balanced out in the build process. Other frequencies' amplitudes, however, cannot be balanced out. Momentum wheels are usually the single largest source of vibrations in a spacecraft and can contribute to pointing inaccuracies if emitted vibrations ring the structure or are in the high-gain bandwidth of a sensitive pointing control loop. It is therefore important to be able to provide an a priori knowledge of possible amplitudes that are singular in source or are a result of interacting defects that do not reveal themselves in normal frequency prediction equations. This paper will describe the computer model that provides for the incorporation of bearing geometry errors and then develops an estimation of actual amplitudes and frequencies. Test results were correlated with the model. A momentum wheel was producing an unacceptable 74 Hz amplitude. The model was used to simulate geometry errors and proved successful in identifying a cause that was verified when the parts were inspected.

Hightower, Richard A., III↗

Characterization of metal-polymer boundaries using Stoneley and Leaky waves

Optical and acoustooptical techniques for bonded surface inspection and interface wave detection are discussed. Interface wave propagation models based on viscous, elastic, and viscoelastic mechanical properties are reviewed. Gross boundary anomalies such as large defects and localized disbond regions were measured using conventional high frequency pulse echo and pitch catch ultratechniques. Bond durabilty is estimated by comparing detected wave attenuation versus frequency as a function of prebond surface preparation with the experimental limit obtained for perfect welded contact. Sensitivity of interface acoustic field periodicity to both residual and dc applied stress at the boundary surface is observed as well as hysteresis due to viscoelastic polymeric behavior as the applied stress is cycled.

Claus, R. O.↗

Overview of Recent Flight Flutter Testing Research at NASA Dryden

In response to the concerns of the aeroelastic community, NASA Dryden Flight Research Center, Edwards, California, is conducting research into improving the flight flutter (including aeroservoelasticity) test process with more accurate and automated techniques for stability boundary prediction. The important elements of this effort so far include the following: (1) excitation mechanisms for enhanced vibration data to reduce uncertainty levels in stability estimates; (2) investigation of a variety of frequency, time, and wavelet analysis techniques for signal processing, stability estimation, and nonlinear identification; and (3) robust flutter boundary prediction to substantially reduce the test matrix for flutter clearance. These are critical research topics addressing the concerns of a recent AGARD Specialists' Meeting on Advanced Aeroservoelastic Testing and Data Analysis. This paper addresses these items using flight test data from the F/A-18 Systems Research Aircraft and the F/A-18 High Alpha Research Vehicle.

Brenner, Martin J.↗

X-ray scatter correction method for dedicated breast computed tomography

Purpose: To improve image quality and accuracy in dedicated breast computed tomography (BCT) by removing the x-ray scatter signal included in the BCT projections. Methods: The previously characterized magnitude and distribution of x-ray scatter in BCT results in both cupping artifacts and reduction of contrast and accuracy in the reconstructions. In this study, an image processing method is proposed that estimates and subtracts the low-frequency x-ray scatter signal included in each BCT projection postacquisition and prereconstruction. The estimation of this signal is performed using simple additional hardware, one additional BCT projection acquisition with negligible radiation dose, and simple image processing software algorithms. The high frequency quantum noise due to the scatter signal is reduced using a noise filter postreconstruction. The dosimetric consequences and validity of the assumptions of this algorithm were determined using Monte Carlo simulations. The feasibility of this method was determined by imaging a breast phantom on a BCT clinical prototype and comparing the corrected reconstructions to the unprocessed reconstructions and to reconstructions obtained from fan-beam acquisitions as a reference standard. One-dimensional profiles of the reconstructions and objective image quality metrics were used to determine the impact of the algorithm. Results: The proposed additional acquisition results in negligible additional radiation dose to the imaged breast ({approx}0.4% of the standard BCT acquisition). The processed phantom reconstruction showed substantially reduced cupping artifacts, increased contrast between adipose and glandular tissue equivalents, higher voxel value accuracy, and no discernible blurring of high frequency features. Conclusions: The proposed scatter correction method for dedicated breast CT is feasible and can result in highly improved image quality. Further optimization and testing, especially with patient images, is necessary to characterize its impact on clinical performance.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Parameter Estimation in Hybrid Active-Passive Laminated Sandwich Composite Structures

In this article we present recent developments regarding parameter estimation in sandwich structures with viscoelastic frequency dependent core and elastic laminated skin layers, with piezoelectric patch sensors and actuators bonded to the exterior surfaces of the sandwich. The frequency dependent viscoelastic properties of the core material are modelled using fractional derivative models, with unknown parameters that are to be estimated by an inverse technique, using experimentally measured natural frequencies and associated modal loss factors. The inverse problem is formulated as a constrained minimization problem, and gradient based optimization techniques are employed. An application case is presented and discussed, focused on identification of viscoelastic frequency dependent core material properties.

36 MATERIALS SCIENCE↗

Carrier Estimation Using Classic Spectral Estimation Techniques for the Proposed Demand Assignment Multiple Access Service

In any satellite communication, the Doppler shift associated with the satellite's position and velocity must be calculated in order to determine the carrier frequency. If the satellite state vector is unknown then some estimate must be formed of the Doppler-shifted carrier frequency. One elementary technique is to examine the signal spectrum and base the estimate on the dominant spectral component. If, however, the carrier is spread (as in most satellite communications) this technique may fail unless the chip rate-to-data rate ratio (processing gain) associated with the carrier is small. In this case, there may be enough spectral energy to allow peak detection against a noise background. In this thesis, we present a method to estimate the frequency (without knowledge of the Doppler shift) of a spread-spectrum carrier assuming a small processing gain and binary-phase shift keying (BPSK) modulation. Our method relies on an averaged discrete Fourier transform along with peak detection on spectral match filtered data. We provide theory and simulation results indicating the accuracy of this method. In addition, we will describe an all-digital hardware design based around a Motorola DSP56303 and high-speed A/D which implements this technique in real-time. The hardware design is to be used in NMSU's implementation of NASA's demand assignment, multiple access (DAMA) service.

Scaife, Bradley James↗

Direct system parameter identification of mechanical structures with application to modal analysis

In this paper a method is described to estimate mechanical structure characteristics in terms of mass, stiffness and damping matrices using measured force input and response data. The estimated matrices can be used to calculate a consistent set of damped natural frequencies and damping values, mode shapes and modal scale factors for the structure. The proposed technique is attractive as an experimental modal analysis method since the estimation of the matrices does not require previous estimation of frequency responses and since the method can be used, without any additional complications, for multiple force input structure testing.

Leuridan, J. M.↗

Resonant shattering flares as asteroseismic tests of chiral effective field theory

Chiral effective field theory (𝜒⁢EFT) has proved to be a powerful microscopic framework for predicting the properties of neutron-rich nuclear matter with quantified theoretical uncertainties up to about twice the nuclear saturation density. Tests of 𝜒⁢EFT predictions are typically performed at low densities using nuclear experiments, with neutron star (NS) constraints only being considered at high densities. In this work, we discuss how asteroseismic quasinormal modes within NSs could be used to constrain specific matter properties at particular densities not just the integrated quantities to which bulk NS observables are sensitive. We focus on the crust-core interface mode, showing that measuring this mode's frequency would provide a meaningful test of 𝜒⁢EFT at densities around half the saturation density. Conversely, we use nuclear matter properties predicted by 𝜒⁢EFT to estimate that this mode's frequency is around 185 ± 50Hz. Asteroseismic observables such as resonant phase shifts in gravitational-wave signals and multimessenger resonant shattering flare timings, therefore, have the potential to provide useful tests of 𝜒⁢EFT.

effective field theory↗

The JPL millimeter, submillimeter and microwave line catalog

The catalog includes molecules of interest in the interstellar medium, in planetary atmospheres and in the Earth's atmosphere. Different units than those on the AFGL tape are used. For citing line frequencies in the microwave region. Either the experimental errors or the propagation of errors from the fit are included on the tape. This gives an estimate of how accurate the frequencies are. The intensity units are defined as follows: the logarithm of the intensity unit is the cross section times the frequency in MHz. This is essentially the same unit as on the AFGL tape, but contains fewer factors of the speed of light. The catalog is available to the scientific community either as a tape or on microfiche (filmed in frequency sorted and molecule sorted format).

Pickett, H.↗

The spectrum of the geoid from altimeter data

A variety of sources of detailed information has been analyzed to arrive at a geoid power spectrum from global altimeter data. Using the equivalent of only two revolutions of data (mostly from GEOS-3) from all the major oceans, the high frequency geoid power (rms) is estimated (most simply) to be 80.7 n to the minus 1.47th power meters, where n is in cycles/global revolutions. This law is valid for all frequencies above 19 cycles but includes sea state. The (simple) law has more power than predicted by Kaula's rule for the geopotential. However, the data shows significantly less power for frequencies below 100 cycles. A closer approximation to the altimetry accumulates 2.18m (rss) for all frequencies higher than 19 cycles/rev. (including sea state), somewhat less power than predicted by the rule. The data permits up to 1.25 (rms) non-gravitational departures from the high frequency marine geoid.

Wagner, C. A.↗

New interpolation algorithm for evaluation a spatial profile of plasma densities in radio frequency discharges

A new interpolation to estimate a spatial profile of plasma densities of unmeasured regions for two-dimensional probe diagnostics is proposed. Our algorithm is based on the plasma diffusion characteristics. From a comparison with a well known interpolation, Modified Shepard, it has been found that our method gives more accurate plasma density profile, especially at the edge region of the measurement substrate, and improves computational efficiency.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spacecraft structural system identification by modal test

A structural parameter estimation procedure using the measured natural frequencies and kinetic energy distribution as observers is proposed. The theoretical derivation of the estimation procedure is described and its constraints and limitations are explained. This procedure is applied to a large complex spacecraft structural system to identify the inertia matrix using modal test results. The inertia matrix is chosen after the stiffness matrix has been updated by the static test results.

Chen, J.-C.↗

Recent Advances to Estimation of Fixed-Interface Modal Models Using Dynamic Substructuring

In 2010, Allen & Mayes proposed to estimate the fixed-interface modes of a structure by measuring the modes of the structure bolted to a fixture and then applying constraints to the fixture using the transmission simulator method. While the method proved useful, and has indeed been used in studies since that point, a few peculiarities were noted. First, in some cases the estimated fixed-base natural frequencies were observed to converge very slowly to the true values (in simulated experiments) as the number of constraints was increased. To formulate these constraints, prior studies used only the free-interface modes of the fixture or the measured modes of the assembly. This work extends that to consider other sets of constraints, showing improved results. Furthermore, in some prior studies it has been observed that there were errors of more than 10% in the natural frequencies even when the fixture motion was hundreds of times smaller than the motion of the structure of interest (and so it had presumably been removed). This work explores this phenomenon, seeking to use the strain energy in the fixture, to the extent that it can be estimated using a test-analysis model for the fixture, as a metric to predict frequency error. The proposed methods are explored by applying them to simulated measurements from a beam and from the NASA Space Launch System coupled to the Mobile Launcher.

Allen, Mathew S.↗

Simple Limits on Achieving A Quasi-Linear Magnetic Compression for an FEL Driver

Free electron lasers (FEL) need a very bright electron beam in three dimensions and a high peak charge density. In order to compress an initially longer electron bunch generated from the photoinjector, magnetic bunch compression systems are widely employed. In this paper, first harmonic RF linearization and its associated requirements are reviewed. Meanwhile it is also briefly discussed what is the relation between a proper initial bunch length and main RF frequency, when a harmonic RF linearization is included. Then given a reasonable bunch compression ratio, a proper initial bunch length as a function of the main RF frequency and RF phase is estimated analytically by several approaches, assuming that no harmonic RF section is needed to linearize the energy modulation introduced during main RF acceleration, and at the same time still linearly compress the bunch length. Next the upper limit of the bunch compression ratio in a single stage is evaluated analytically. The analytical relations derived on choosing a proper initial bunch length as a function of main RF frequency are confirmed by numerical simulation. These simple limit provide rough estimations and may be beneficial for choosing bunch compression ratios in different stages of an FEL driver, especially in a first stage bunch compression where there is usually a harmonic RF linearization applied. It may also be useful in evaluating the possibility of low charge operation mode without any harmonic RF linearization, where a shorter initial bunch length can be achieved from the photoinjector.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Estimating Explosion Yields Using Moment Tensor Solutions and Seismic Moment

We report seismic moment, a measurable and well-understood quantity of seismic sources, is used to estimate the yield of explosions. Application of such a method in the past, as in the manner of m b -derived yields, has been complicated by the effect of variations in the explosion working point, depth, and secondary source effects (such as spalling and tectonic release) on the observed moment. We start using the full (six-element) moment tensor solution, which can capture the relevant source physics and, at least in theory, better isolate the primary explosion source. The moment-to-yield ratio is then estimated using an explosion source model which, provided with emplacement conditions, can relate the two parameters. We discuss the major sources of uncertainty associated with the method, and calibrate it with chemical and nuclear explosions at the Nevada National Security Site. We then apply the method to published moment tensor solutions for the six declared North Korean nuclear explosions that occurred between 2006 and 2017. The results are mostly consistent with other yield estimates made using a variety of high-frequency methods. This technique is a new approach to estimating explosive yield and simple to implement, as much of the complexity is captured by the source models.

58 GEOSCIENCES↗

Selection of optimum frequencies for atmospheric electric path length measurement by satellite-borne microwave radiometers

Numerical experiments using regressions by leaps and bounds have been performed to determine the optimum frequencies for satellite-borne microwave radiometers to estimate atmospheric electrical path length over the sea. The frequency range 5-40 GHz was searched. The effect of surface wind speed, sea surface temperature, and clouds was considered in the optimum frequency selection. The analysis indicates that approximately 0.6-cm rms accuracy is possible for one-way path length measurement using a proper pair of frequencies. The best two-channel subset selected by the leaps and bounds techniques is (16.0, 21.0) GHz.

Pandey, P. C.↗