Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Development of coal-derived carbon-based structural unit as a potential new building material

Coal combustion for energy has not only wasted the hydrogen-rich volatile matters but also results in CO 2 emission causing serious environmental issues. An integrated coal pyrolysis and solvent extraction process under elevated temperatures in an inert atmosphere is implemented to convert as-mined coal from Wyoming Powder River Basin to functional carbon elements such as pyrolysis char (PC). This paper presents the development and fabrication of new carbon-based structural unit (CSU) using pulverized PC and two coal-derived pitches (mesophase pitch and tar pitch) to attain high compressive strength greater than 30 MPa, low thermal conductivity less than 0.30 W/m.K, and low density less than 1.25 g/cm 3 . CSUs have the potential to overcome the current challenges with cement and concrete through pressurized fabrication followed by carbonization. This study aims to develop CSU with nearly 100% coal-derived carbon material for structural application in buildings. The effects of pressing pressures, carbonization temperatures, and binder contents on the density and mechanical and thermal properties of CSU samples are investigated. The study concludes that mesophase pitch produces a better performance of CSU samples, a combination of 100 MPa pressing pressure and carbonization temperature of 900 ⁰C yields the highest compressive strength, and a 25% MP content is recommended for low-cost CSU fabrication. Furthermoer, CSU has a much lower density, lower thermal conductivity, higher compressive strength, and higher strength-to-density ratio than normal concrete.

36 MATERIALS SCIENCE↗

Processing of crack-free high density polycrystalline LiTaO3 ceramics

Our work achieved high density (99.9%) polycrystalline LiTaO 3 . The keys to the high density without cracking were the use of LiF-assisted densification to maintain fine grain size as well as the presence of secondary lithium aluminate phases as grain growth inhibitors. The average grain size of the hot pressed polycrystalline LiTaO 3 is less than 5 μm, limiting residual stresses caused by the anisotropic thermal expansion. Dilatometry results clearly indicate liquid phase sintering via the added LiF sintering aid. Efficient liquid phase sintering allows densification during low temperature hot pressing. Electron microscopy confirmed the high-density microstructure. Furthermore, Rietveld analysis of neutron diffraction data revealed the presence of LiAlO 2 and LiAl 5 O 8 minority phases and negligible substitutional defect incorporation in LiTaO 3 .

36 MATERIALS SCIENCE↗

Production of Hydrogel Microneedles from Fish Scale Biopolymer

This work presents for the first time, a scalable, low cost method for producing hydrogel microneedles from fish scales derived biopolymer using a modified low temperature press method. The microneedles are made from cross-linked hydrolyzed collagen (HC). The suitability of the microneedles for drug loading were tested by loading with Ferrous gluconate. Force analysis carried out in compression mode showed that the microneedles could withstand up to 0.136 N per microneedle before fracture which is sufficient strength to pierce the skin. The cross-linked microneedles swelled to 340% of their original mass in PBS and within 24 h released 34.5% of the loaded drug, while the non cross-linked microneedles dissolved within minutes. Chemical testing of the released drug confirmed that the drug released retained its chemical structure by forming colored complex with acetylsalicylic acid and UV spectrometry was used to quantify the concentration released. FTIR analysis confirmed the modified structure of the polymer when cross-linked. This proposed method allows cross-linking at room temperature using a thermal press method which can be easily scaled up.

60 APPLIED LIFE SCIENCES↗

Compaction of Titanium Powders

Accurate modeling of powder densification has been an area of active research for more than 60 years. The earliest efforts were focused on linearization of the data because computers were not readily available to assist with curve-fitting methods. In this work, eight different titanium powders (three different sizes of sponge fines<150 {micro}m,<75 {micro}m, and<45 {micro}m; two different sizes of a hydride-dehydride [HDH]<75 {micro}m and<45 {micro}m; an atomized powder; a commercially pure [CP] Ti powder from International Titanium Powder [ITP]; and a Ti 6 4 alloy powder) were cold pressed in a single-acting die instrumented to collect stress and deformation data during compaction. From these data, the density of each compact was calculated and then plotted as a function of pressure. The results show that densification of all the powders, regardless of particle size, shape, or chemistry, can be modeled accurately as the sum of an initial density plus the sum of a rearrangement term and a work-hardening term. These last two terms are found to be a function of applied pressure and take the form of an exponential rise.

36 MATERIALS SCIENCE↗

Effect of Air and Argon Sintering Atmospheres on Properties and Hydrothermal Aging Resistance of Y-TZP Ceramics

In this work, we investigated the role of sintering atmosphere and temperature on low-temperature degradation of 3 mol.% yttria tetragonal zirconia polycrystals ceramics. Green compacts were prepared by die-pressing followed by cold isostatic pressing at 200 MPa. The green bodies were sintered between the temperature range of 1250 and 1500 °C in air and argon gas atmosphere. Sintered samples were tested to determine bulk density, Young’s modulus, Vickers hardness and fracture toughness. The results revealed that the mechanical properties of air-sintered samples were better than that of argon-sintered samples sintered at 1400 °C and below while the argon sintering marginally improves the fracture toughness and hardness when sintered at 1450 °C and above. FESEM images showed that the tetragonal grain size was similar when sintered in argon atmosphere. However, regardless of sintering atmosphere, grain growth was inevitable as the sintering temperature was increased. Hydrothermal aging test in superheated steam was performed in an autoclave at temperature of 180 °C and 10 bar pressure up to 12 h. Effect of aging on tetragonal-to-monoclinic phase transformation was measured by using x-ray diffraction. The phase transformation was found to be strongly influenced by the sintering temperature and sintering atmosphere. The sample sintered at 1500 °C in argon atmosphere exhibited rapid phase transformation compared to air atmosphere, while the samples sintered at or below 1400 °C in argon showed no phase transformation after 12-h exposure in steam environment.

36 MATERIALS SCIENCE↗

Functionally Graded W-Cu Materials Prepared from Cu-Coated W Powders by Microwave Sintering

Three-layered W-Cu (W-10Cu/W-20Cu/W-30Cu, weight percentage) functionally graded materials were fabricated by laminate pressing of Cu-coated W composite powders with different Cu contents (10-30 wt.% Cu) and W particle sizes in the powders and microwave sintering of the powder compacts. The microstructure and the physical and mechanical properties of the graded materials were investigated. The experimental results show that the relative density of the graded W-Cu samples sintered at 1250 °C for 20 min is above 97%. Cu has a gradient layer distribution in the thickness direction, and there is good combination between the layers in the graded samples. Furthermore, the graded W-Cu materials exhibit good physical and mechanical properties. The sintered samples have thermal conductivities above 210 W m K{sup −1}, and the maximum bending strength and hardness reach 1004 MPa and 346 HV, respectively. The present results show that functionally graded W-Cu materials with high density, gradient Cu and W distribution, and good properties can be successfully prepared by laminate pressing and microwave sintering.

36 MATERIALS SCIENCE↗

Oxidation Resistance in 1200°C Steam of a FeCrAl Alloy Fabricated by Three Metallurgical Processes

Abstract FeCrAl alloys are a leading candidate material for accident tolerant fuel cladding due to their good performance in both normal light-water reactor operating conditions as well as their resilience to high-temperature accident scenarios. For commercial-scale production, new fabrication techniques need to be investigated. In this study, the effects of fabrication methods on the high-temperature steam oxidation performance of C26M (Fe12Cr6Al2Mo in wt.%) were investigated. Three variants of C26M were manufactured: wrought (cast and forged) (WC26M), powder metallurgy hot isostatic pressing (PMC26M), and laser powder bed fusion additive manufacturing (AMC26M). All three variants were exposed to steam at 1200°C for 2 h. Results showed no significant variation in mass change between the variants after steam exposure. All three variants effectively formed stable protective alumina films with ~0.6–1.3 µ m thickness. This study suggests FeCrAl alloys have excellent resilience to high-temperature steam in nuclear reactor accident scenarios regardless of the fabrication method.

Materials Science↗

Effect of heat treatment on microstructural evolution and hardness homogeneity in laser powder bed fusion of alloy 718

The thermal history developed in laser powder bed fusion (LPBF) processes has been shown to be complex resulting in equally complex microstructures and mechanical properties. Microscopic observations and Vickers micro-hardness mapping measurements were carried out on diff ;erent section planes of LPBF alloy 718 cuboids. Three-dimensional finite element analysis was used to simulate thermal history and to predict the residual stress distribution in the as-built material. Computational thermodynamics was used to predict the micro-segregation and nucleation driving force of various phases in the bulk and in segregated regions. Varied heat-treatments such as simulated hot isostatic pressing, and double aging were applied. Their influence on the microstructure, microsegregation, precipitate formation, and micro-hardness variations of LPBF alloy 718 were investigated. Hardness map results showed heterogeneous micro-hardness on the xy- and xz-planes of the as-built parts where the bottom plane and center regions had larger hardness of ~315 HV 0.5 while the top plane and contours showed hardness of ~300 HV 0.5 . It was found that the aging treatment increased the overall hardness of the as-built condition from ~310 HV 0.5 to 470 HV 0.5 but also increased the hardness gradient throughout the coupon. After simulated hot isostatic pressing process (i.e., without applied pressure) at 1020 °C for 4 h followed by water quench (HIPWQ), the hardness gradient and hardness was minimized (~210 HV 0.5 ) as the microstructure transitioned from heterogeneous columnar grains in the as-built condition to more uniform recrystallized grains. A double aging treatment was applied to enhance hardness from ~210 HV 0.5 to ~440 HV 0.5 . Finally, HIPWQ followed by double aging produced a homogeneous microstructure and more uniform hardness map with enhanced mechanical properties in LPBF alloy 718 coupons.

36 MATERIALS SCIENCE↗

Densification and microstructure features of lithium hydride fabrication

The manufacturing of lithium hydride (LiH) utilizing uniaxial pressing, which offers fabrication with tailorable properties via microstructure control, can lead to the expansion in application of LiH while bypassing the challenges presented by historical casting manufacturing techniques. Through control of consolidation conditions such as pressure, temperature, dwell time and powder load, the presented work highlights the densification of LiH, with an emphasis on quantifying oxygen content, for applications requiring a specific density range necessary for optimized material performance. Karl Fischer Titration and X-ray Diffraction proved useful in determining oxygen and phase content while Computed Tomography and Scanning Electron Microscopy provided structural analysis. The temperature dependent densification of LiH fit with an Arrhenius term resulted in an activation energy of 21.2 kJ/mol. Images of fractured surfaces of LiH pressed at 500 °C revealed drastic grain coarsening, aided by the presence of oxygen impurities.

36 MATERIALS SCIENCE↗

Microwave assisted heating of plastic waste: Effect of plastic/susceptor (SiC) contacting patterns

We discuss plastic accumulation as a growing sustainability challenge. Most plastics are thermally inert at room temperature, requiring high temperatures for depolymerization. In the quest for developing sustainable plastic upcycling, we investigate silicon carbide (SiC) as microwave absorbing susceptors for reaching depolymerization temperatures. We utilize three SiC topologies – particles, hot-pressed plastic films containing SiC particles, and monoliths. SiC particles of >0.5 mm in diameter can provide heating rates approaching ~200 °C/min at modest powers. Still, physically mixed plastic-susceptor beds suffer from density differences, causing non-uniform contact during plastic softening and melting. Hot-pressed plastic films containing SiC particles allow uniform plastic-susceptor contact but suffer from slow heating as only a single layer of susceptors exists between polymer layers. SiC monoliths mitigate these challenges by preferentially dissipating the microwaves and rapidly heating the plastics independently of polymeric properties.

36 MATERIALS SCIENCE↗

Effect of lot microstructure variations on detonation performance of the triaminotrinitrobenzene (TATB)-Based insensitive high explosive PBX 9502

PBX 9502 is an important insensitive high explosive due to its combination of safety properties and detonation performance. It is a polymer-bonded formulation consisting of 95 wt.% 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) as the high explosive crystal, bound with Kel F-800 (FK-800), a co-polymer of chlorotrifluoroethylene and vinylidene-fluoride. Two different types are used, one known as virgin that uses only pristine manufactured TATB, and a second known as recycled that has 50 wt.% of its TATB reclaimed from machining scraps of previously pressed virgin PBX 9502. Recycled lots have a higher percentage of fine particles compared to virgin lots, due to the fracturing and damage sustained by TATB crystals during pressing. We examine the influence that this TATB microstructure difference between virgin and recycled PBX 9502 has on detonation performance properties. New rate-stick geometry diameter effect, detonation front shape and cylinder expansion test data are obtained for two previously uncharacterized virgin lots and one recycled lot of PBX 9502. This is combined with previously published data for one virgin and one recycled lot for evaluation purposes. Detonation shock dynamics model calibrations are conducted on each of the five lots to provide an assessment of the detonation timing characteristics of virgin versus recycled PBX 9502 lots. For two of the virgin lots, detonations propagate slower in the rate-stick geometry than those in the two recycled lots. However, the other virgin lot tested has propagation rates comparable to that of the recycled lots for larger diameter rate-sticks. The latter result, though, is shown to be geometry dependent and depends on the range of detonation curvatures accessed in different geometries. New copper-confined, cylinder expansion tests are conducted on each of the three virgin and two recycled lots to obtain detonation product Jones-Wilkins-Lee equations of state, enabling an assessment of the metal push capabilities for each of the five lots. We find that the metal push capabilities, characterized by the evolution of the heat of detonation with volume, are similar between the virgin and recycled lots. Thus, changes in microstructure between different PBX 9502 lots seemingly affect the rate of reaction, but not the overall energy content.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrical property enhancement of non-heat-treatable wrought aluminum alloys using graphene additives

With growing efforts of electrification, aluminum’s role as a light-weight conductor material has become increasingly prominent. There is a critical need to improve the electrical performance of aluminum at room temperature and high operating temperatures. In this study, the effect of graphene nanoparticle additives on the electrical performance of a non-heat treatable alloy were (AA3003) explored. Graphene’s unusual structure and electronic properties were used to improve AA3003 properties. Here, in this work, the effects of graphene on the evolution of electrical properties and microstructural features have been explored on lab scale hot extruded AA3003-graphene composites. Hot pressing schedules and extrusion temperatures were varied to investigate changes in intermetallic dispersion characteristics in the presence of dispersed graphene. We measured a reduction of 10.3 % in the temperature coefficient of resistance in the AA3003 sample with 0.05 wt% graphene extruded at 400 °C, along with a maximum increase of 1.1 % in electrical conductivity at 20 °C. Increasing the hot-pressing times up to 8 hours was also found to consistently increase the electrical conductivity, due to increased precipitation of intermetallic phases. Despite being a non-heat treatable alloy, AA3003 displays interesting precipitation dynamics and grain recrystallization trends that can be modulated with varying levels of heat treatment, graphene concentrations, and hot extrusion process parameters.

36 MATERIALS SCIENCE↗

Reaction-bond composite synthesis of SiC-TiB 2 by spark plasma sintering/field-assisted sintering technology (SPS/FAST)

High-density SiC-TiB 2 composites were fabricated using the displacement reaction spark plasma sintering/field-assisted sintering technology (SPS/FAST) and SiC, B 4 C, TiC, and Si powders. The reaction process was performed in a narrow time frame compared hot pressing. The SiC-TiB 2 composites were sintered with precursor SiC at various pressures to determine the effects of processing with SPS/FAST. The composites completed synthesis during SPS/FAST processing, which occurs more quickly than hot pressing. SEM, STEM, and Raman spectroscopy are used to show the conversion and microstructure. Finally, the composite of 53.6 wt.% SiC and 46.4 wt.% TiB 2 has 99 % theoretical density, hardness of 26.4 GPa, and fracture toughness of 5.12 MPa m 1/2 .

36 MATERIALS SCIENCE↗

Fast-rate joining of thermoplastic composites using integrated additive manufacturing and compression molding process

The integration of additive manufacturing (AM) technology with compression molding (CM), has emerged as a high-performance composite manufacturing technology in recent years. In the AM-CM process, quickly deposited AM preform on a mold undergoes a rapid compaction cycle to fabricate structurally robust composite parts due to highly controlled fiber alignment (from AM) and reduced porosity (from CM). Currently, AMCM-based part size is limited by the size of the mold volume, thus posing a challenge to manufacture scalable parts. Here, this work focuses on joining techniques developed to enable fast rate joining of short fiber-reinforced thermoplastic composite parts using the AM-CM process. Acrylonitrile butadiene styrene resin reinforced with 20 wt% short carbon fiber composites was printed onto a flat mold and pressed under a hydraulic press. Fabricated panels were joined by the (a) mechanical impression at the joining interface and (b) over-molded continuous carbon fiber (CCF) sheet. Tensile tests were performed to characterize the joining strength of both mechanical impression-based joints and CCF over molded joints. Among the mechanical impression-based joints, a U-shape channel allowed the fibers to flow between two joint parts, and 280 % increased mechanical properties were observed. The continuous carbon fiber-based over molded joint CCF showed 350 % increase in tensile strength compared to the butt joints.

36 MATERIALS SCIENCE↗

Glass-bonded iodosodalite waste form for immobilization of 129I

Immobilization of radioiodine (e.g., 129I, 131I) is an important need for current and future nuclear fuel cycles. For the current work, iodosodalite [Na8(AlSiO4)6I2] was synthesized hydrothermally from metakaolin, NaI, and NaOH. Following hydrothermal treatment, dried unwashed powders were used to make glass-bonded iodosodalite waste forms by heating pressed pellets at 650, 750, or 850 °C with two different types of sodium borosilicate glass binders, i.e., NBS-4 and SA-800. These heat-treated specimens were characterized with X-ray diffraction, Fourier-transform infrared spectroscopy, scanning electron microscopy, energy dispersive spectroscopy, thermal analysis, porosity and density measurements, neutron activation analysis, and inductively-coupled plasma mass spectrometry. The pellets mixed with 10 mass% of NBS-4 or SA-800 and heat-treated at 750 °C contained relatively high percentage iodine retention (~44-47 % of the maximum iodine loading) with relatively low porosities, while other pellets with higher percentages iodine retention either contained higher porosity or were not completely sintered. ASTM C1308 chemical durability tests of monolithic specimens showed a large initial release of Na, Al, Si, and I on the first day, possibly from water-soluble salt crystals or non-durable amorphous phases. Release rates of Na and Si were higher than for Al and I, probably due to a poorly durable Na-Si-O phase from the glass bonding matrix. The cumulative normalized release of iodine was 12.5 g m-2 for the first 10 1-d exchanges, suggestive of coherent dissolution. The average release rate from 10-24 days during the 7-d exchange intervals was 0.2336 g m-2 d-1.

sodalite, iodosodalite, waste forms, iodine↗

UO2 microstructural evolutions induced by Ni, Mo, and W dopants for intentional forensics

The concept of tagging nuclear fuel with a chemical barcode to enable forensics analysis across the nuclear fuel cycle is an area of active investigation, particularly to ensure fabrication viability without disrupting current fuel performance. This study explored the feasibility of using Ni, Mo, and W isotopic double-spikes as dopants in UO2 fuel from the perspective of fuel fabrication. Doped UO2 pellets were produced using conventional fuel fabrication processes, including powder mixing, sieving, pressing, and sintering in a reductive atmosphere. Two composition levels, 100 and 1000 ppm, were evaluated for each dopant element with isotopic double-spike configurations. For the Ni system, additional dopant concentrations of 250 and 500 ppm were produced with nonperturbed isotopic ratios. The results demonstrated that successful incorporation of Ni, Mo, and W double-spikes into UO2 pellets occurred with minimal shift in final density or dopant loss during pellet fabrication. Isotopic analysis confirmed the presence of the double-spike signature even when diluted with natural isotopic material in ratio of 1:5 in the fabrication process. Microstructural examinations revealed different impacts on grain size compared with undoped UO2. This study showed that Ni incorporation up to ∼500 ppm promoted moderate grain growth, whereas the Mo and W systems caused grain size reduction at all concentrations. Changes in the UO2 lattice parameter as a function of composition were detected exclusively for Ni up to 500 ppm, indicating that the Ni solid solution was the main factor for the observed grain growth. Insoluble (Mo and W) or supersaturated (Ni > 500 ppm) conditions produced grain size reduction. The Ni-doped pellets in the solution range resulted in a final microstructure within fuel specifications, demonstrating its potential benefits of employing complex dopant systems for potential nuclear forensic applications.

36 MATERIALS SCIENCE↗

Rational anode design for protonic ceramic fuel cells by a one-step phase inversion method

A one-step phase inversion method was applied to fabricate an optimized anode structure for protonic ceramic fuel cells (PCFCs). The phase inversion process utilized raw starting chemicals, instead of crystalline BaCe 0.7 Z r0.1 Y 0.1 Yb 0.1 O 3-δ (BCZYYb) powder in an energy and time saving process. The resulting large and fingerlike pores exhibited enhanced performance as compared to the disordered pores produced by conventional preparation of anode structures using dry pressing methods. The electrochemical performance of the rational designed anode supported cell were 491, 402, 302 and 200 mW cm -2 at 700, 650, 600 and 550 °C, respectively, which was nearly twice than the cell with dry pressing anode. An equivalent circuit modeling method was used to separate the anode polarization resistance from the single cell, confirming that the overall cell performance improvements were attributed to microstructural modifications of the anode by the phase inversion process. The one-step phase inversion method demonstrated great promise for improved processing of fuel cells and separation membranes.

25 ENERGY STORAGE↗

Fabrication of high-performance gas-diffusion-electrode based membrane-electrode assemblies

This paper demonstrates the fabrication and processing steps required to produce high performance fuel cell membrane electrode assemblies (MEAs) based on spray-coated gas-diffusion electrodes (GDEs). It is demonstrated that coating the catalyst layer with a thin layer of ionomer and then hot pressing the GDEs to the membrane is required to achieve comparable catalyst activity and air performance to catalyst-coated-membrane MEAs. We show that there is a critical amount of ionomer required to achieve maximized performance. Using electron microscopy, we show that the combination of the ionomer overlayer and hot-pressing bonds the catalyst layer to the membrane, increasing the interfacial contact area and quality of this interface. We also find that the ionomer overlayer smooths the surface of the GDE and provides increased contact area between the GDE and the membrane. Additionally, we demonstrate that much less ionomer is required for high-performance than has been previously reported. Through model fitting of electrochemical impedance spectroscopy, we show that this improvement in the catalyst layer - membrane interface reduces the effective catalyst layer resistance, which reduces Ohmic losses and increases catalyst utilization.

33 ADVANCED PROPULSION SYSTEMS↗