Search NASA⌕ Search

SEARCH · Search NASA

Results for “work”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Experimental study of the performance of a very small repetitive plasma focus device in different working conditions

SORENA-1 is a very small repetitive Mather-type plasma focus device (20 J) that can operate at frequencies up to 1 Hz. This device has been designed and constructed in the Plasma and Nuclear Fusion Research School of the Nuclear Science and Technology Research Institute of Iran. In this article, the structure of SORENA-1 is described and results of experiments with Ar, Ne, and D{sub 2} working gases at several discharge voltages and initial pressures are presented and analyzed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

KSC Child Development Center (Potential Release Location 149) Confirmatory Sampling Report and Interim Measures Work Plan

This Confirmatory Sampling (CS) Report and Interim Measures (IM) Work Plan was prepared for the National Aeronautics and Space Administration (NASA), Kennedy Space Center (KSC), Florida, by HydroGeoLogic, Inc. (HGL) under Contract Number 80KSC019D0012, Task Order 80KSC019F0118. This document presents the results of the CS activities performed in March 2022, and May 202, at the KSC Child Development Center (KCDC), Potential Release Location (PRL) 149, KSC, Florida. This report additionally presents the results of an assessment conducted in July 2023 to determine whether construction activities in 2023 to replace certain playground equipment and the rubberized play surface allowed soil contaminated by arsenic (As) to migrate from beneath the play surface.

arsenic↗

Microstructural Effects on SCC Initiation PWR Primary Water Cold-Worked Alloy 600

SCC initiation behavior of one mill annealed alloy 600 plate heat was investigated in simulated PWR primary water under constant load at yield stress with in-situ direct current potential drop (DCPD) monitoring for crack initiation. Twelve specimens were tested at similar cold work levels among which three showed much shorter SCC initiation times (<400 hrs) than the others (>1200 hrs). Post-test examinations revealed that these three specimens all feature an inhomogeneous microstructure where the primary crack always nucleated along the boundary of large elongated grains protruding normally into the gauge. In contrast, such microstructure was either not observed or did not extend deep enough into the gauge in the other specimens exhibiting ~3-6X longer initiation times. In order to better understand the role of this microstructural inhomogeneity in SCC initiation, high-resolution microscopy was performed to compare carbide morphology and strain distribution between the long grains and normal grains, and their potential effects on SCC initiation are discussed in this paper.

Alloy 600↗

High-Temperature Properties and Microstructural Stability of the AISI H13 Hot-Work Tool Steel Processed by Selective Laser Melting

The microstructural stabilities, softening resistance, and high-temperature tensile properties of the H13 hot-work tool steel by selective laser melting (SLM) were systematically studied. A series of tempering procedures were performed on the as-SLMed specimens. Afterwards, the mechanism of softening resistance behavior was discussed based on the XRD, SEM, EBSD observations, hardness measurements, and high-temperature tensile tests. It was found that the as-SLMed H13 consisted of α-iron and γ-iron. The carbide-stabilizing elements aggregated as the cell-like substructures for the rapid solidification of the SLM process. After the softening resistance treatment, the retained austenite transformed to ferrite and carbide mixtures. The cell-like substructures dissolved slowly into the matrix when the temperature was below 550 °C. These factors increased the hardness and retarded the softening of the material. When the temperature was 600 °C, the microstructural constituents transformed to soft ferrite and globular carbides, which lead to a considerable decrease of the hardness. Due to the grain refinement, solid solution strengthening, and residual stress, the as-SLMed H13 exhibited better mechanical properties than that of the wrought counterparts.

36 MATERIALS SCIENCE↗

Potential impact of work from home jobs on residential energy bills: A case study in phoenix, AZ, USA

Nearly one-third of U.S. households face challenges paying energy bills. During the day, many residents have routine access to cooled environments provided by others—employers, shopping centers, and other public buildings. The COVID-19 pandemic, however, has significantly shifted the cost burden of air conditioning in hot cities. Specifically, during the pandemic, many companies either laid off employees or put them in work-from-home (WFH) assignments. Large tech companies are already promoting WFH as a long-term option for their employees, even after the pandemic. This change in the nature of the workforce might reduce daily travel expenses for workers, but could also significantly increase residential energy bills, particularly during summer in very hot climates. Here, this study uses building energy simulations to quantify the potential residential energy bill penalties resulting from WFH for typical residences in Phoenix. Four building archetypes are used in this study to represent variations in building vintage, occupancy, and characteristics. The results show that, for some single-family residences in Phoenix, WFH can increase annual energy bills by more than $1100 (up to a 70% increase). The study also demonstrates that building performance enhancement retrofit measures have the potential to reduce this WFH energy bill penalty for the existing buildings substantially.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Work Function Tuning of a Weak Adhesion Homojunction for Stable Perovskite Solar Cells

Perovskite solar cells (PSCs) have demonstrated a comparable efficiency to Si-based cells. However, the buried interface with weak adhesion remains a critical issue since the ion migration enhanced by the built-in electric field at this interface might lead to instability. We report here that adjusting the energy-level alignment at the weak adhesion homojunction interface can mitigate ion migration and thereby enhance the stability and photovoltaic performance of PSCs. Functional molecules with self-assembled monolayer characteristics were introduced to the surface of the SnO2 layer using silane derivatives, which tuned the work function of the homojunction depending on the functional groups in the molecules and thereby significantly reduced the built-in electric field. The PSC exhibited a power conversion efficiency (PCE) of 25.3%. The maximum power point (MPP) tracking under continuous illumination confirmed that the device retained more than 97% of its initial PCE, even after 1,000 h.

homojunction↗

Changes to the morphology, structure and properties as a consequence of polyethylene working in a polymer-metal kinematic pair

A change is presented of the orientation of lamellar structure, degree of crystallinity, the degree of the spatial arrangement of the structure, micromechanical properties, and the surface morphology and thickness of a plastically deformed upper layer. These changes are the effect of work in a polymer-metal kinematic pair, which have occurred as a result of plastic deformation of polyethylene during its service. It has been shown that, as a result of selecting proper parameters of UHMW polyethylene via the initial draft and electron-beam irradiation, such a structure of the polymer can be obtained, which will enable the above-mentioned changes in morphology and structure to take place during service. This in turn, will allow a reduction of the susceptibility of the polymer to permanent deformation by 3-6 times, and its wear by more than 5 times, compared to the initial material.

36 MATERIALS SCIENCE↗

Effect of cold working and isothermal aging on the precipitation of sigma phase in 2205 duplex stainless steel

A comprehensive understanding of the formation of the sigma phase resulting from the eutectoid reaction ({delta} {yields} {sigma} + {gamma}{sub 2}) is required. The kinetics necessary for the eutectoid reaction are closely related to the amount of plastic deformation in DSS. This work investigates the microstructural evolution of the {sigma} phase in a 22Cr-5Ni SAF 2205 DSS after subsequent plastic deformation and isothermal aging. The precipitation of the {sigma} phase resulted from the higher driving force for precipitating intermetallic compounds and the higher diffusion rate of their elements by cold-rolling, as well as the sufficient supply of molybdenum. The maximum amount of {sigma} phase precipitation remarkably increased with an increasing cold deformation, as compared with the non-cold-rolled materials. - Highlights: Black-Right-Pointing-Pointer The microstructural evolution of sigma phase has been characterized. Black-Right-Pointing-Pointer The chemical compositions of sigma phases were analyzed using TEM-EDX. Black-Right-Pointing-Pointer The effect of cold deformation on the precipitation of sigma phase was investigated.

36 MATERIALS SCIENCE↗

Hot deformation characteristics of AZ80 magnesium alloy: Work hardening effect and processing parameter sensitivities

Isothermal compression experiment of AZ80 magnesium alloy was conducted by Gleeble thermo-mechanical simulator in order to quantitatively investigate the work hardening (WH), strain rate sensitivity (SRS) and temperature sensitivity (TS) during hot processing of magnesium alloys. The WH, SRS and TS were described by Zener-Hollomon parameter (Z) coupling of deformation parameters. The relationships between WH rate and true strain as well as true stress were derived from Kocks-Mecking dislocation model and validated by our measurement data. The slope defined through the linear relationship of WH rate and true stress was only related to the annihilation coefficient Ω. Obvious WH behavior could be exhibited at a higher Z condition. Furthermore, we have identified the correlation between the microstructural evolution including β-Mg17Al12 precipitation and the SRS and TS variations. Intensive dynamic recrystallization and homogeneous distribution of β-Mg17Al12 precipitates resulted in greater SRS coefficient at higher temperature. The deformation heat effect and β-Mg17Al12 precipitate content can be regarded as the major factors determining the TS behavior. At low Z condition, the SRS becomes stronger, in contrast to the variation of TS. The optimum hot processing window was validated based on the established SRS and TS values distribution maps for AZ80 magnesium alloy.

36 MATERIALS SCIENCE↗

Enhanced working memory performance via transcranial direct current stimulation: The possibility of near and far transfer

Although working memory (WM) training programs consistently result in improvement on the trained task, benefit is typically short-lived and extends only to tasks very similar to the trained task (i.e., near transfer). It is possible that pairing repeated performance of a WM task with brain stimulation encourages plasticity in brain networks involved in WM task performance, thereby improving the training benefit. In the current study, transcranial direct current stimulation (tDCS) was paired with performance of a WM task (n-back). In Experiment 1, participants performed a spatial location-monitoring n-back during stimulation, while Experiment 2 used a verbal identity-monitoring n-back. In each experiment, participants received either active (2.0 mA) or sham (0.1 mA) stimulation with the anode placed over either the right or the left dorsolateral prefrontal cortex (DLPFC) and the cathode placed extracephalically. In Experiment 1, only participants receiving active stimulation with the anode placed over the right DLPFC showed marginal improvement on the trained spatial n-back, which did not extend to a near transfer (verbal n-back) or far transfer task (a matrix-reasoning task designed to measure fluid intelligence). Here, in Experiment 2, both left and right anode placements led to improvement, and right DLPFC stimulation resulted in numerical (though not sham-adjusted) improvement on the near transfer (spatial n-back) and far transfer (fluid intelligence) task. Results suggest that WM training paired with brain stimulation may result in cognitive enhancement that transfers to performance on other tasks, depending on the combination of training task and tDCS parameters used.

60 APPLIED LIFE SCIENCES↗

Reconciling Work Functions and Adsorption Enthalpies for Implicit Solvent Models: A Pt (111)/Water Interface Case Study

Implicit solvent models are a computationally efficient method of representing solid/liquid interfaces prevalent in electrocatalysis, energy storage, and materials science. However, electronic structure changes induced at the metallic surface by the dielectric continuum are not fully understood. To address this, we perform DFT calculations for the Pt(111)/water interface, in order to compare Poisson–Boltzmann continuum solvation methods with ab initio molecular dynamics (AIMD) simulations of explicit solvent. We show that the implicit solvent cavity can be parametrized in terms of the electric dipole moment change at the equilibrated explicit Pt/water interface to obtain the potential of zero charge (PZC). We also compare the accuracy of aqueous enthalpies of adsorption of phenol on Pt(111) using geometry and charge density based dielectric cavitation methods. The ability to parametrize the cavity according to individual atoms, as afforded in the geometry based approach, is key to obtaining accurate enthalpy changes of adsorption under aqueous conditions. Additionally, we show that the electronic structure changes induced by explicit solvent and our proposed implicit solvent parametrization scheme yield comparable density difference profiles and d-band projected density of states. We therefore demonstrate the capability of implicit solvent approaches to capture both the energetics of adsorption processes and the main electronic effects of aqueous solvent on the metallic surface. Therefore, this work provides a scheme for computationally efficient simulations of interfacial processes for applications in areas such as heterogeneous catalysis and electrochemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reversible work function changes induced by photoisomerization of asymmetric azobenzene dithiol self-assembled monolayers on gold

We measured reversible changes in the work function ({delta}{phi}{sub Au}) of gold substrates modified by asymmetric azobenzene dithiol self-assembled monolayers (SAMs) following photoisomerization and thermal recovery of the azo unit. The azobenzene derivative SAMs were photoisomerized to cis form by UV irradiation. {delta}{phi}{sub Au} was monitored in real time during thermal recovery to trans form by ultraviolet photoelectron spectroscopy using a synchrotron light source. Changing the substituted functional group in the p{sup '} position of the azobenzene from electron donating to electron withdrawing resulted in opposite responses of {delta}{phi}{sub Au} against photoisomerization. Hence, a direct correlation between {delta}{phi}{sub Au} and changes in molecular dipole moments was obtained.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effective work function lowering of multilayer graphene films by subnanometer thick AlO{sub x} overlayers

A simple method for controlling the effective work function (WF) of conductive multilayer graphene (MLG) film, synthesized by using chemical vapor deposition and transferred to a dielectric substrate, was developed. The WFs of the MLG during the step-by-step deposition of aluminum (Al) were measured using in situ ultraviolet photoelectron spectroscopy. Core-level spectra were also collected to investigate the chemical reaction that occurred when a small amount of Al was deposited onto MLG in a stepwise manner. The measurements revealed that the effective WF of the conductive MLG film could be controlled from 3.77 to 4.40 eV by the deposition of an Al layer less than 0.6 nm thick.

36 MATERIALS SCIENCE↗

Bare-tether cathodic contact through thermionic emission by low-work-function materials

A new material, C12A7:e{sup -} electride, which might present a work function as low as 0.6 eV and moderately high temperature stability, was recently proposed as coating for floating bare tethers. Arising from heating under space operation, current is emitted by thermionic emission along a thus coated cathodic segment. A preliminary study on the space-charge-limited (SCL) double layer in front of the cathodic segment is presented using Langmuir's SCL electron current between cylindrical electrodes and orbital-motion-limited ion-collection sheath. A detailed calculation of current and bias profiles along the entire tether length is carried out with ohmic effects and the transition from SCL to full Richardson-Dushman emission included. Analysis shows that in the simplest drag mode, under typical orbital and tether conditions, thermionic emission leads to a short cathodic section and may eliminate the need for an active cathodic device and its corresponding gas feed requirements and power subsystem, which results in a truly 'propellant-less' tether system for such basic applications as de-orbiting low earth orbit satellites.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Determination of effective work function of Pr{sub 0.7}Ca{sub 0.3}MnO{sub 3} and Pt films on ZrO{sub x} using terraced-oxide method

We have determined the effective work function ({Phi}{sub m,eff}) of thin-film sputter-deposited Pr{sub 0.7}Ca{sub 0.3}MnO{sub 3} (PCMO) on atomic-layer-deposited ZrO{sub x}. Pt/PCMO/ZrO{sub x}/SiO{sub 2}/Si and Pt/ZrO{sub x}/SiO{sub 2}/Si metal-oxide-semiconductor (MOS) capacitors were fabricated. The {Phi}{sub m,eff} were extracted from capacitance-voltage curves of the MOS capacitors by using flat-band voltage versus effective-oxide-thickness plots. PCMO was crystallized using a high-temperature anneal step and crystallinity was confirmed by x-ray diffraction and transmission electron microscopy. {Phi}{sub m,eff} of polycrystalline PCMO and Pt on ZrO{sub x} was determined to be 5.43 eV and 5.40 eV, respectively. The significantly higher {Phi}{sub m,eff} of PCMO is attributed to the presence of oxygen-rich PCMO(002)/ZrO{sub x} interfaces as indicated by our density-functional-theory calculations.

36 MATERIALS SCIENCE↗

Tuning of noble metal work function with organophosphonate nanolayers

We demonstrate that weak chemical interactions between untethered moieties in molecular nanolayers on metal surfaces can strongly influence the effective work function Φ{sub eff}. Electron spectroscopy shows that nanolayers of mercaptan-anchored organophosphonates on Au and Pt decrease Φ{sub eff}. The measured Φ{sub eff} shifts correlate with the chemical state of phosphonic acid moieties, and scale with molecular length. These results are contrary to predictions of ab initio calculations of monolayer-capped surfaces, but are consistent with calculations of bilayer-capped surfaces with face-to-face hydrogen-bonded phosphonic acid moieties. Our findings indicate that intra-layer bonding and layering in molecular nanolayers can be key to tailoring heterointerfacial electronic properties for applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Protection of MoO{sub 3} high work function by organic thin film

The effects of air exposure are investigated for molybdenum trioxide (MoO{sub 3}) covered with organic thin films using ultraviolet photoemission spectroscopy. It is found that the severe drop of the work function of MoO{sub 3} by air exposure is substantially reduced by the organic thin films. Both CuPc and C{sub 60} are used for the investigations. The results indicate that the MoO{sub 3} surface can be passivated by approximately two monolayers of organic thin films against exposure to air.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗