Search NASA⌕ Search

SEARCH · Search NASA

Results for “IMPACT SHOCK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49

The Influence of Ablation on Radiative Heating for Earth Entry

Using the coupled ablation and radiation capability recently included in the LAURA flowfield solver, this paper investigates the influence of ablation on the shock-layer radiative heating for Earth entry. The extension of the HARA radiation model, which provides the radiation predictions in LAURA, to treat a gas consisting of the elements C, H, O, and N is discussed. It is shown that the absorption coefficient of air is increased with the introduction of the C and H elements. A simplified shock layer model is studied to show the impact of temperature, as well as the abundance of C and H, on the net absorption or emission from an ablation contaminated boundary layer. It is found that the ablation species reduce the radiative flux in the vacuum ultraviolet, through increased absorption, for all temperatures. However, in the infrared region of the spectrum, the ablation species increase the radiative flux, through strong emission, for temperatures above 3,000 K. Thus, depending on the temperature and abundance of ablation species, the contaminated boundary layer may either provide a net increase or decrease in the radiative flux reaching the wall. To assess the validity of the coupled ablation and radiation LAURA analysis, a previously analyzed Mars-return case (15.24 km/s), which contains significant ablation and radiation coupling, is studied. Exceptional agreement with previous viscous shock-layer results is obtained. A 40% decrease in the radiative flux is predicted for ablation rates equal to 20% of the free-stream mass flux. The Apollo 4 peak-heating case (10.24 km/s) is also studied. For ablation rates up to 3.4% of the free-stream mass flux, the radiative heating is reduced by up to 19%, while the convective heating is reduced by up to 87%. Good agreement with the Apollo 4 radiometer data is obtained by considering absorption in the radiometer cavity. For both the Mars return and the Apollo 4 cases, coupled radiation alone is found to reduce the radiative heating by 30 60% and the convective heating by less than 5%.

Johnston, Christopher O.↗

Asteroidal agglutinate formation and implications for asteroidal surfaces

The possible role of spallation on the free surfaces of target bodies in asteroid surface evolution in the presence of colliding bodies is considered. The ease of impact melt formation is discussed based on the results of shock recovery experiments, and a difference between collisions with dense, nonporous targets and with porous, particulate powders is demonstrated. It is shown that agglutinate-type glasses can be produced at impact velocities of 5 km/sec, but only in highly comminuted, porous targets and not in dense rocks. The apparent lack of agglutinate-type glasses on asteroid surfaces is explained in terms of coarse-grained asteroidal surfaces acting as dense, nonporous bedrock. It is argued that a possible mechanism inhibiting asteroidal surface comminution so as to inhibit melt formation and the effects of micrometeoroid impacts can be represented by collision processes with finite-sized targets rather than with a semi-infinite half-space as in the case of the moon, which give rise to spallation products rather than crater ejecta.

Horz, F.↗

Weak-shock wave propagation in polymer-based particulate composites

Shock waves are common in polymer-based particulate composites that are subjected to intermediate to high-velocity impact loading. However, quantitative information on the spatial variation of stress, particle velocities, and energy dissipation during the formation and propagation of weak-shock waves is limited. In this paper, a systematic experimental study is conducted to understand the characteristics of weak-shocks in polymer-bonded particulate composites. Specimens made of polymer-bonded sugar were subjected to a projectile impact loading, at varying velocities, using a modified Hopkinson pressure bar apparatus. Full-field displacement and strains of the deformed samples were obtained with the help of an ultrahigh-speed imaging and digital image correlation technique. Using the full-field displacement data, the shock wave velocity, shock front thickness, and the full-field stress fields are calculated. From the spatial stress field and the strain rate data, the spatial energy dissipation profile is also estimated. The effect of impact velocity on the spatial stress profile, shock wave velocity, and energy dissipation are discussed.

42 ENGINEERING↗

The debate over the Cretaceous-Tertiary boundary

Large-body impact on the Earth is a rare but indisputable geologic process. The impact rate is approximately known from objects discovered in Earth-crossing orbits and from the statistics of craters on the Earth's surface. Tektite and microtektite strewn fields constitute unmistakable ejecta deposits that can be due only to large-body impacts. The Cretaceous-Tertiary (K-T) boundary coincides with an unusually severe biological trauma, and this stratigraphic horizon is marked on a worldwide basis by anomalous concentrations of noble metals in chondritic proportions, mineral spherules with relict quench-crystallization textures, and mineral and rock grains showing shock deformation. These features are precisely compatible with an impact origin. Although only impact explains all the types of K-T boundary evidence, the story may not be as simple as once thought. The original hypothesis envisioned one large impact, triggering one great extinction. Newer evidence hints at various complications. Different challenges are faced by the occupants of each apex of a three-cornered argument over the K-T event. Proponents of a non-impact explanation must show that the evidence fits their preferred model better than it fits the impact scenario. Proponents of the single impact-single extinction view must explain away the complications. Proponents of a more complex impact crisis must develop a reasonable scenario which honors the new evidence.

Alvarez, W.↗

Reflectance Changes during Shock-induced Phase Transformations in Metals

In performing shock wave experiments to study the characteristics of metals at high pressures, wave profiles (i.e., velocity measurements of the surface of the sample) are an established and useful way to study phase transformations. For example, a sudden change in the velocity or its slope can occur when the phase transformation induces a large volume change leading to a change in particle velocity. Allowing the shock to release into a transparent window that is in contact with the sample surface allows the study of conditions away from the shock Hugoniot. However, in cases where the wave profile is not definitive an additional phase-transformation diagnostic would be useful. Changes in the electronic structure of the atoms in the crystal offer opportunities to develop new phase-change diagnostics. We have studied optical reflectance changes for several phase transformations to see whether reflectance changes might be a generally applicable phase-transformation diagnostic. Shocks were produced by direct contact with explosives or with impacts from guns. Optical wavelengths for the reflectance measurements ranged from 355 to 700 nm. We studied samples of tin, iron, gallium, and cerium as each passed through a phase transformation during shock loading and, if observable, a reversion upon unloading. For solid-solid phase changes in tin and iron we saw small changes in the surface scattering characteristics, perhaps from voids or rough areas frozen into the surface of the sample as it transformed to a new crystal structure. For melt in gallium and cerium we saw changes in the wavelength dependence of the reflectance, and we surmise that these changes may result from changes in the crystal electronic structure. It appears that reflectance measurements can be a significant part of a larger suite of diagnostics to search for difficult-to-detect phase transformations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Primary Mineralogical and Chemical Characteristics of the Major K/T and Late Eocene Impact Deposits

Three well-characterized, distal impact deposits at the WT boundary and in upper Eocene sediments serve as a baseline for understanding other proposed impact deposits. All contain abundant spherules, evidence of shock metamorphism, and the largest have significant extraterrestrial components (ETCs). The K/T and the Eocene cpx-spherule (cpxS) deposits are global - likely from the events that produced the 180 km Chicxulub and 100 km Popigai craters. The Eocene North American microtektite (NAM) deposit is regional and likely from the event that produced the 45 km Chesapeake Bay crater. These deposits all contain abundant spherules formed from both shock-melted target and mixtures of target and projectile in the ejecta plume. Spherules constitute most of the mass of the distal ejecta. K/T spherules in regional deposits around the Gulf of Mexico are from low-velocity, target-rich ejecta. These can be a few mm in size and form deposits 10s of cm thick. Globally deposited KIT spherules from the plume (typically a few hundred micron size) are both target- and projectile-rich. When well preserved, the global deposits are 3 mm thick. Eocene cpxS deposits are similar to distal K/T with both target- and projectile-rich varieties (Le., glassy microtektite, and cpx spherules). They are smaller on average than WT spherules, concentrated in the 125-250 micron and smaller fractions. They are invariably bioturbated, but the initial deposit was probably less than 1 mm thick. The NAM are composed entirely of target-rich glass. They are similar in size to the cpxS. Size is an important criterion for distal ejecta because droplet size in the impact plume is proportional to the energy of the impact. Both the JUT and cpxS deposits are characterized by well-defined ETCs, commonly measured by Ir. The total Ir deposited is about 55 ng per square cm in WT sediments, and about 11 ng for the cpxS layer. This 5/1 proportion in Ir is generally consistent with the approx.1.8/1 ratio in crater diameters. The NAM have no significant ETC. This may be a function of the smaller impact. It indicates there was no significant projectile-rich plume deposit.

Kyte, Frank T.↗

Elastic-plastic deformation of molybdenum single crystals shocked to 12.5 GPa: Crystal anisotropy effects

Here, to understand crystal anisotropy effects on shock-induced elastic-plastic deformation of molybdenum (Mo), results from high-purity single crystals shocked along [110] and [111] orientations to an elastic impact stress of 12.5 GPa were obtained and compared with the [100] results previously reported [A. Mandal and Y. M Gupta, J. Appl. Phys. 121, 045903 (2017)]. Measured wave profiles showed a time-dependent response, and strong anisotropy was observed in the elastic wave attenuation with the propagation distance, elastic limits, shock speeds, and overall structure of the wave profiles. Resolved shear stresses on {110} $\langle$111$\rangle$ and {112} $\langle$111$\rangle$ slip systems provided insight into the observed anisotropy in elastic wave attenuation and elastic limits and showed that shear stresses, and not longitudinal stresses, are a better measure of strength in shocked single crystals. Under shock compression, resolved shear stresses at elastic limits were comparable to the Peierls stress of screw dislocations in Mo. Elastic wave attenuation was rapid when shear stresses were larger than the Peierls stress. Large differences in the elastic limits under shock and quasi-static loading are likely a consequence of the large Peierls stress value for Mo. Numerically simulated wave profiles, obtained using the dislocation-based plasticity model described in the [100] work, showed good agreement with all measured wave profiles but could not differentiate between the {110} $\langle$111$\rangle$ and {112} $\langle$111$\rangle$ slip systems. Overall, experimental results and corresponding numerical simulations for the three crystal orientations have provided a comprehensive insight into shock-induced elastic-plastic deformation of Mo single crystals, including the development of a continuum material model.

36 MATERIALS SCIENCE↗

Shock during PIND test frees particles

Recent study on Particle-Impact Noise-Detection (PIND) shows impact at 1,500 to 4,000 G normally imparted to hybrid microcircuits during testing knocks loose stray trapped particle that can be subsequentially removed. Process may be 80 to 90 percent effective in removal of particles depending on type of test utilized.

Caruso, S. V.↗

An MDOE Investigation of Chevrons for Supersonic Jet Noise Reduction

The impact of chevron design on the noise radiated from heated, overexpanded, supersonic jets is presented. The experiments used faceted bi-conic convergent-divergent nozzles with design Mach numbers equal to 1.51 and 1.65. The purpose of the facets was to simulate divergent seals on a military style nozzle. The nozzle throat diameter was equal to 4.5 inches. Modern Design of Experiment (MDOE) techniques were used to investigate the impact of chevron penetration, length, and width on the resulting acoustic radiation. All chevron configurations used 12 chevrons to match the number of facets in the nozzle. Most chevron designs resulted in increased broadband shock noise relative to the baseline nozzle. In the peak jet noise direction, the optimum chevron design reduced peak sound pressure levels by 4 dB relative to the baseline nozzle. The penetration was the parameter having the greatest impact on radiated noise at all observation angles. While increasing chevron penetration decreased acoustic radiation in the peak jet noise direction, broadband shock noise was adversely impacted. Decreasing chevron length increased noise at most observation angles. The impact of chevron width on radiated noise depended on frequency and observation angle.

Henderson, Brenda↗

Shock, Post-Shock Annealing, and Post-Annealing Shock in Ureilites

The thermal and shock histories of ureilites can be divided into four periods: 1) formation, 2) initial shock, 3) post-shock annealing, and 4) post-annealing shock. Period 1 occurred approx.4.55 Ga ago when ureilites formed by melting chondritic material. Impact events during period 2 caused silicate darkening, undulose to mosaic extinction in olivines, and the formation of diamond, lonsdaleite, and chaoite from indigenous carbonaceous material. Alkali-rich fine-grained silicates may have been introduced by impact injection into ureilites during this period. About 57% of the ureilites were unchanged after period 2. During period 3 events, impact-induced annealing caused previously mosaicized olivine grains to become aggregates of small unstrained crystals. Some ureilites experienced reduction as FeO at the edges of olivine grains reacted with C from the matrix. Annealing may also be responsible for coarsening of graphite in a few ureilites, forming euhedral-appearing, idioblastic crystals. Orthopyroxene in Meteorite Hills (MET) 78008 may have formed from pigeonite by annealing during this period. The Rb-Sr internal isochron age of approx.4.0 Ga for MET 78008 probably dates the annealing event. At this late date, impacts are the only viable heat source. About 36% of ureilites experienced period 3 events, but remained unchanged afterwards. During period 4, approx.7% of the ureilites were shocked again, as is evident in the polymict breccia, Elephant Moraine (EET) 83309. This rock contains annealed mosaicized olivine aggregates composed of small individual olivine crystals that exhibit undulose extinction. Ureilites may have formed by impact-melting chondritic material on a primitive body with heterogeneous O isotopes. Plagioclase was preferentially lost from the system due to its low impedance to shock compression. Brief melting and rapid burial minimized the escape of planetary-type noble gases from the ureilitic melts. Incomplete separation of metal from silicates during impact melting left ureilites with relatively high concentrations of trace siderophile elements.

Rubin, Alan E.↗

Solar Eruptions, CMEs and Space Weather

Coronal mass ejections (CMEs) are large-scale magnetized plasma structures ejected from the Sun and propagate far into the interplanetary medium. CMEs represent energy output from the Sun in the form of magnetized plasma and electromagnetic radiation. The electromagnetic radiation suddenly increases the ionization content of the ionosphere, thus impacting communication and navigation systems. The plasma clouds can drive shocks that accelerate charged particles to very high energies in the interplanetary space, which pose radiation hazard to astronauts and space systems. The plasma clouds also arrive at Earth in about two days and impact Earth's magnetosphere, producing geomagnetic storms. The magnetic storms result in a number of effects including induced currents that can disrupt power grids, railroads, and underground pipelines. This lecture presents an overview of the origin, propagation, and geospace consequences of solar storms.

Gopalswamy, Nat↗

Coronal Mass Ejections Near the Sun and in the Interplanetary Medium

Coronal mass ejections (CMEs) are the most energetic phenomenon in the heliosphere. During solar eruptions, the released energy flows out from the Sun in the form of magnetized plasma and electromagnetic radiation. The electromagnetic radiation suddenly increases the ionization content of the ionosphere, thus impacting communication and navigation systems. The plasma clouds can drive shocks that accelerate charged particles to very high energies in the interplanetary space, which pose radiation hazard to astronauts and space systems. The plasma clouds also arrive at Earth in about two days and impact Earth's magnetosphere, producing geomagnetic storms. The magnetic storms result in a number of effects including induced currents that can disrupt power grids, railroads, and underground pipelines. This lecture presents an overview of the origin, propagation, and geospace consequences of CMEs and their interplanetary counterparts.

Gopalswamy, Nat↗

Hypervelocity impact effects on solar cells

One of the space hazards of concern is the problem of natural matter and space debris impacting spacecraft. In addition to mechanical damage, impact velocities greater than 5 km/sec can produce shock induced ionization effects with resultant surface charging and complex chemical interactions. The upper limit of the velocity distribution for these particles is on the order of 70 km/sec. The second source of particulate matter is due to the presence of man and the machinery needed to place satellites in orbit. This 'man made' component of the space debris consists of waste, rocket exhaust, and debris caused by satellite break-up. Most of the particles are small. However as the size increases, debris purposefully thrown overboard such as garbage and human waste, combined with paint chips, plastic, wire fragments, bolts, etc., become formidable hazards which completely dominate the distribution function for some orbits. These larger fragments can produce penetration and spalling of the thick metallic structures associated with spacecraft. The particles most often encountered are aluminum oxide, associated with fuel residue, and paint chips. These debris types can have a wide range of particle sizes. It has been stated that the design of spacecraft will have to take the debris evolution into account and provide additional suitable armor for key components in the near future. The purpose of this work was to subject samples from solar power arrays, one of the key components of any spacecraft, to a debris flux typical of what might be found in space, and measure the degradation of the power panels after impact.

Rose, M. Frank↗

The size distributions of fragments ejected at a given velocity from impact craters

The mass distribution of fragments that are ejected at a given velocity for impact craters is modeled to allow extrapolation of laboratory, field, and numerical results to large scale planetary events. The model is semi-empirical in nature and is derived from: (1) numerical calculations of cratering and the resultant mass versus ejection velocity, (2) observed ejecta blanket particle size distributions, (3) an empirical relationship between maximum ejecta fragment size and crater diameter, (4) measurements and theory of maximum ejecta size versus ejecta velocity, and (5) an assumption on the functional form for the distribution of fragments ejected at a given velocity. This model implies that or planetary impacts into competent rock, the distribution of fragments ejected at a given velocity is broad, e.g., 68% of the mass of the ejecta at a given velocity contains fragments having a mass less than 0.1 times a mass of the largest fragment moving at that velocity. The broad distribution suggests that in impact processes, additional comminution of ejecta occurs after the upward initial shock has passed in the process of the ejecta velocity vector rotating from an initially downward orientation. This additional comminution produces the broader size distribution in impact ejecta as compared to that obtained in simple brittle failure experiments.

Okeefe, J. D.↗

The size distributions of fragments ejected at a given velocity from impact craters

The mass distribution of fragments that are ejected at a given velocity for impact craters is modeled to allow extrapolation of laboratory, field, and numerical results to large scale planetary events. The model is semi-empirical in nature and is derived from: (1) numerical calculations of cratering and the resultant mass versus ejection velocity, (2) observed ejecta blanket particle size distributions, (3) an empirical relationship between maximum ejecta fragment size and crater diameter, (4) measurements and theory of maximum ejecta size versus ejecta velocity, and (5) an assumption on the functional form for the distribution of fragments ejected at a given velocity. This model implies that for planetary impacts into competent rock, the distribution of fragments ejected at a given velocity is broad, e.g., 68 percent of the mass of the ejecta at a given velocity contains fragments having a mass less than 0.1 times a mass of the largest fragment moving at that velocity. The broad distribution suggests that in impact processes, additional comminution of ejecta occurs after the upward initial shock has passed in the process of the ejecta velocity vector rotating from an initially downward orientation. This additional comminution produces the broader size distribution in impact ejecta as compared to that obtained in simple brittle failure experiments.

O'Keefe, John D.↗

Shock-Absorbent Ball-Screw Mechanism

Actuator containing two ball screws in series employs Belleville springs to reduce impact loads, thereby increasing life expectancy. New application of springs increases reliability of equipment in which ball screws commonly used. Set of three springs within lower screw of ball-screw mechanism absorbs impacts that result when parts reach their upper and lower limits of movement. Mechanism designed with Belleville springs as shock-absorbing elements because springs have good energy-to-volume ratio and easily stacked to attain any stiffness and travel.

Hirr, Otto A., Jr.↗

Large Bore Powder Gun Qualification (U)

A Large Bore Powder Gun (LBPG) is being designed to enable experimentalists to characterize material behavior outside the capabilities of the NNSS JASPER and LANL TA-55 PF-4 guns. The combination of these three guns will create a capability to conduct impact experiments over a wide range of pressures and shock profiles. The Large Bore Powder Gun will be fielded at the Nevada National Security Site (NNSS) U1a Complex. The Complex is nearly 1000 ft below ground with dedicated drifts for testing, instrumentation, and post-shot entombment. To ensure the reliability, safety, and performance of the LBPG, a qualification plan has been established and documented here. Requirements for the LBPG have been established and documented in WE-14-TR-0065 U A, Large Bore Powder Gun Customer Requirements. The document includes the requirements for the physics experiments, the gun and confinement systems, and operations at NNSS. A detailed description of the requirements is established in that document and is referred to and quoted throughout this document. Two Gun and Confinement Systems will be fielded. The Prototype Gun will be used primarily to characterize the gun and confinement performance and be the primary platform for qualification actions. This gun will also be used to investigate and qualify target and diagnostic modifications through the life of the program (U1a.104 Drift). An identical gun, the Physics Gun, will be fielded for confirmatory and Pu experiments (U1a.102D Drift). Both guns will be qualified for operation. The Gun and Confinement System design will be qualified through analysis, inspection, and testing using the Prototype Gun for the majority of process. The Physics Gun will be qualified through inspection and a limited number of qualification tests to ensure performance and behavior equivalent to the Prototype gun. Figure 1.1 shows the partial configuration of U1a and the locations of the Prototype and Physics Gun/Confinement Systems.

CONFIGURATION↗

Search for a meteoritic component at the Beaverhead impact structure, Montana

The Beaverhead impact structure, in southwestern Montana, was identified recently by the presence of shatter cones and impactites in outcrops of Proterozoic sandstones of the Belt Supergroup. The cones occur over an area greater than 100 sq km. Because the geologic and tectonic history of this region is long and complex, the outline of the original impact crater is no longer identifiable. The extent of the area over which shatter cones occur suggests, however, that the feature may have been at least 60 km in diameter. The absence of shatter cones in younger sedimentary units suggests that the impact event occurred in late Precambrian or early Paleozoic time. We have collected samples of shocked sandstone from the so-called 'Main Site' of dark-matrix breccias, and of impact breccias and melts from the south end of Island Butte. The melts, occurring often as veins through brecciated sandstone, exhibit a distinctive fluidal texture, a greenish color, and a cryptocrystalline matrix, with small inclusions of deformed sandstone. Samples of the same type, along with country rock, were analyzed previously for major- and trace-element abundances. It was found that, although the major-element composition as relatively uniform, trace-element composition showed variations between the melt material and the adjacent sandstone. These variations were attributed to extensive weathering and hydrothermal alteration. In a more specific search for a possible meteoritic signature in the breccia and the melt material we have conducted a new series of trace-element analyses on powders of our own samples by thermal neutron activation analysis. Our results indicate that Ir abundances in the breccia, the melts, and the adjacent sandstone clasts are no greater than about 0.1 ppb, suggesting no Ir enrichment of the breccia or the melts relative to the country rock. However, both the breccia and the melt material exhibit notable enrichments in Cr (8- and 10-fold), in U (9- and 5-fold), and in the heavy REE's (1.5- and 3-fold), respectively.

Lee, Pascal↗