Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrical doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Artificial particle and wave stimulation in the Trigger experiment

The Trigger experiment, designed to test the response of the auroral ionosphere to an impulsive release of a hot, dense plasma, and consisting of a sounding rocket payload (launched on February 11, 1977) divided into two parts, an instrumented diagnostic section and a cesium-doped high-explosive canister, is described. When the two sections were separated by about 1 km, the cesium high-explosive was ignited and the plasma around the payload was observed to increase briefly by a factor of 4 in density and a factor of 2 in temperature, upon which various particle and field phenomena occurred in rapid succession. A large increase in the field-aligned charged particle flux was observed over the approximate energy range of 10 eV to more than 300 keV, starting about 150 ms after the release and lasting about 1 second. A second particle burst started one second after the release and lasted for tens of seconds. A transient electric field pulse of 200 mV/m appeared just before the particle flux increase began.

Holmgren, G.↗
NASA NTRS2001

Measurement of Microscopic Growth Rates in Float-Zone Silicon Crystals

Time dependent convective flows during crystal growth of doped semiconductors lead to fluctuations of the composition, so called dopant striations. In general, it is difficult to decide which is the main mechanism for the generation of these striations, it might be either the fluctuation of the concentration field in the melt and the extent of the solute boundary layer ahead of the solid-liquid interface or a variation of the growth velocity. Direct access to the concentration field is rather complicated to achieve, especially considering the high process temperature and the chemical activity of liquid silicon. The contribution of growth rate fluctuations to the formation of compositional fluctuations can be determined by measuring microscopic growth rates. The classical method of current pulses requires electrical feed-throughs and good electrical contacts, both are critical issues for the growth of high purity silicon crystals. Using a radiation based heating system, the heating power can be modulated very fast and effectively. We added to the normal heater power a sinusoidal off-set in the frequency range of 1 to 10 Hz, generating a narrow spaced weak rippling in the grown crystals which are superposed to the dopant striations caused by natural and by thermocapillary convection. The pulling speed was varied between 1 and 4mm/min. The microscope images of etched crystals slices have been analyzed by peak-search algorithms (measuring the spacing between each artificially induced marker) and by FFT. Performing growth experiments under a time-dependent flow regime, fluctuations of the microscopic growth velocity of Delta(v)/v(sub average) up to 50% have been measured. Damping the time-dependent convection by the use of an axial, static magnetic field of 500mT, the microscopic growth rate became constant within the resolution limit of this method. The results will be discussed using analytical methods for the calculation of microscopic growth velocity and by comparing them with measurements of temperature fluctuations in the melt during growth experiments itself.

Dold, P.↗
DOE OSTI2023

Yb Substitution and Ultralow Thermal Conductivity of the Ca 3– x Yb x AlSb 3 (0 ≤ x ≤ 0.81(1)) System

Here, a series of Yb-substituted Zintl phases in the Ca 3–x Yb x AlSb 3 (0 ≤ x ≤ 0.81(1)) system has been synthesized by initial arc melting and post-heat treatment, and their isotypic crystal structures were characterized by both powder and single crystal X-ray diffraction analysis. All four title compounds adopted the Ca 3 AlAs 3 -type structure (space group Pnma, Pearson code oP28, Z = 4). The overall structure can be described as a combination of the 1-dimensional (1D) infinite chain of ∞ 1 [Al(Sb 2 Sb 2/2 )] formed by two vertices sharing [AlSb 4 ] tetrahedral moieties and three Ca 2+ /Yb 2+ mixed sites located in between these 1D chains. The charge balance and the resultant independency of the 1D chains in the title system were explained by the Zintl-Klemm formalism [Ca 2+ /Yb 2+ ] 3 [(4b-Al 1– )(1b-Sb 2– ) 2 (2b-Sb 1– ) 2/2 ]. A series of DFT calculations proved that (1) the band overlap between the d-orbital states from two types of cations and the p-orbital states from Sb at the high symmetry Γ point implied a heavily doped degenerate semiconducting behavior of the quaternary Ca 2 YbAlSb 3 model and (2) the site preference of Yb for the M1 site was due to the electronic-factor criterion based on the Q values of each atomic site. The electron localization function calculations also proved that the two different shapes of lone pairs of the Sb atoms—the “umbrella-shape” and the “C-shape”—are determined by local geometry and the coordination environment on the anionic frameworks. Thermoelectric measurements of the quaternary title compound Ca 2.19(1) Yb 0.81 AlSb 3 showed an approximately two times larger ZT value than that of ternary Ca 3 AlSb 3 at 623 K due to increased electrical conductivity and ultralow thermal conductivity originated from Yb substitution for Ca.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Design considerations for gallium arsenide pulse compression photoconductive switch

In this paper, we present the physics and design-space exploration of a novel pulse compression photoconductive switch (PCPS) using semi-insulating gallium arsenide (GaAs) operating in the negative differential mobility (NDM) regime of electron transport. We systematically quantify the relationship between the PCPS performance and various design options, including contact separation, laser energy and placement, and trap dynamics. Specifically, we report the full-width at half-maximum and the peak output current generated by the PCPS as a function of applied electrical and optical bias. We discuss the optimal spacing between the electrodes and the distance of the laser spot to the anode to achieve higher electron confinement and superior radio-frequency (RF) metrics. Reducing the laser energy is important to prevent the appearance of secondary peaks due to diffusive transport, but there exists a trade-off between the bandwidth and the maximum current of the PCPS. We also compare the PCPS response with and without trap dynamics and find that the electrostatic screening from the trap-induced space charge is time-independent when the trapping time constant is set larger than the recombination lifetime. Overall, trap dynamics are detrimental to performance, unless the compensation doping scheme to achieve semi-insulating GaAs is carefully selected. Results presented in this paper can be used by experimentalists to fine-tune the PCPS design parameters to meet the specifications of various RF applications. Moreover, our results will provide a strong theoretical basis to the measurements of PCPS devices using GaAs and other NDM materials under investigation.

42 ENGINEERING↗
DOE OSTI2025

Understanding the optoelectronic properties of doped 2D organic-inorganic halide perovskite quantum wells: towards efficient ultrafast quantum well IR photodetectors

This project, titled “Understanding the optoelectronic properties of doped 2D organic-inorganic halide perovskite quantum wells: towards efficient quantum well IR photodetectors”, was funded by the U.S. Department of Energy to explore a new class of materials that could make future light-sensing technologies, such as infrared (IR) cameras and detectors more efficient, affordable, and widely available. The research focused on special layered materials called 2D halide perovskites, which are made up of alternating organic and inorganic layers only a few atoms thick. These materials can be tuned at the atomic level to absorb and emit light in precise ways, making them very attractive for use in optoelectronic devices. The main goal of the project was to understand how these perovskite materials absorb light and move electrical charges at very small scales. However, this is not an easy task. These materials often contain a mixture of different structures in the same film, and traditional tools like regular absorption or photoluminescence spectroscopy are not good at telling those structures apart. To solve this, the research team, led by Professor Luisa Whittaker-Brooks at the University of Utah developed a powerful method called electroabsorption spectroscopy. This technique uses electric fields to highlight the unique “fingerprints” of different excitons, which are tiny packets of energy formed when light hits the material. By using this method, the team could separate overlapping signals and learn exactly how the materials respond to light under different conditions, including changes in temperature, thickness, and chemical makeup.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Wet chemical synthesis and properties of argyrodite sulfide solid electrolytes for solid state lithium batteries

The commercialization of the lithium-ion battery (LIB) in 1991 was responsible for the explosion in portable electronic technologies that has been seen over the past 30 years. With the advent of electric vehicles and other high-powered technologies, there is tremendous demand for LIBs with higher energy density and high safety. To achieve this, new electrode materials must be explored. The obvious choice of anode material would be pure metal lithium, which has a theoretical specific capacity of 3860 mAh g-1 . Unfortunately, metal lithium anodes have not been widely commercialized due to their tendency to react violently with the flammable liquid electrolytes used in today’s batteries. Battery safety can best be achieved by adopting solid electrolytes in place of liquid electrolytes. Solid electrolytes are nonvolatile and nonflammable, safely allowing for the combination of high-capacity cathode materials with a Li metal anode. Argyrodite sulfide solid electrolytes such as halogen-doped Li6PS5X (X = Cl, Br, I) are noted for their high ionic conductivity. But before sulfides can be commercially adopted, they possess several disadvantages which must be addressed, including time- and energy-consuming synthesis processes, poor electrochemical stability, and intrinsically poor air stability. This dissertation seeks to address each of these challenges through materials design an synthesis strategies. In this work, we pioneer a solvent-based approach for the synthesis of argyrodite solid electrolytes Li7PS6 and Li6PS5Xinstead of a stringent solid-state synthesis. Nontoxic ethanol is employed as the solvent, enabling a rapid synthetic approach to produce argyrodite solid electrolytes with high phase purity and compositional flexibility. Compared with Li7PS6, halogen doping (i.e. X = F, Cl, Br, I) not only increases the ionic conductivity, but also enhances the electrochemical stability at the interface towards Li metal. Specifically, F-doped argyrodites produce a robust SEI layer containing LiF, contributing to enhanced interfacial stability. Finally, to address the air instability challenge, argyrodite-incorporated composite solid electrolytes (CSEs) are designed and prepared to produce stable and flexible membranes that are demonstrated in solid-state Li metal batteries. These advances push argyrodite sulfide solid electrolyte research further and pave the way for the proliferation of next generation lithium metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Performance degradation in proton-conducting ceramic fuel cell and electrolyzer stacks

Proton-conducting ceramics are emerging as enabling materials for efficient electrochemical electricity generation, energy storage, and fuels synthesis. In this work, we present longer-term degradation results for protonic-ceramic fuel cells and electrolyzers based on a BaCe 0.4 Zr 0.4 Y 0.1 Yb 0.1 O 3-δ (BCZYYb) electrolyte. The cells are packaged within unit-cell stacks, including metallic interconnects, current collectors, sealing glasses and gaskets. Durability is found to be superior in protonic-ceramic electrolyzers in comparison to fuel cells. Operating conditions have a large impact on degradation rates; better stability is found at fuel-cell operating temperatures above 600 °C, and electrolyzer steam feeds below 20%. Here, we find that both fuel-cell and electrolyzer degradation is greatly reduced via the introduction of a gadolinium-doped ceria interlayer between the electrolyte and the air–steam electrode. Fuel-cell degradation falls to 1.2% khr –1 under methane fuel at 600 °C; electrolyzer degradation is reduced to 1% khr –1 at 550 °C and 50% steam. Further analyses of electrochemical impedance spectroscopy and distribution of relaxation times provide insight to root processes and degradation phenomena in protonic electroceramics.

25 ENERGY STORAGE↗
DOE OSTI2023

Cascade electrocatalysis via AgCu single-atom alloy and Ag nanoparticles in CO 2 electroreduction toward multicarbon products

Electrocatalytic CO 2 reduction into value-added multicarbon products offers a means to close the anthropogenic carbon cycle using renewable electricity. However, the unsatisfactory catalytic selectivity for multicarbon products severely hinders the practical application of this technology. In this paper, we report a cascade AgCu single-atom and nanoparticle electrocatalyst, in which Ag nanoparticles produce CO and AgCu single-atom alloys promote C-C coupling kinetics. As a result, a Faradaic efficiency (FE) of 94 ± 4% toward multicarbon products is achieved with the as-prepared AgCu single-atom and nanoparticle catalyst under ~720 mA cm -2 working current density at -0.65 V in a flow cell with alkaline electrolyte. Density functional theory calculations further demonstrate that the high multicarbon product selectivity results from cooperation between AgCu single-atom alloys and Ag nanoparticles, wherein the Ag single-atom doping of Cu nanoparticles increases the adsorption energy of *CO on Cu sites due to the asymmetric bonding of the Cu atom to the adjacent Ag atom with a compressive strain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

The Role and Substitution of Cobalt in the Cobalt‐Lean/Free Nickel‐Based Layered Transition Metal Oxides for Lithium Ion Batteries

Here, the Nickel-based layered transition metal oxide cathode represented by NCM (LiNi x Co y Mn z O 2 , x+y+z=1) and NCA (LiNi x Co y Al z O 2 , x+y+z=1) is widely used in the electric vehicle market due to its specific capacity and high working potential, in which Cobalt (Co) plays a huge role in improving the structural stability during the cycle. However, the limited supply of Co, due to its scarcity and the influence of geopolitics, poses a significant constraint on the further advancement of the Nickel-based layered transition metal oxide cathode in the field of energy storage. In this paper, the mechanism of Co in the Nickel-based layered transition metal oxides is reviewed, including its critical role for structural stability such as the inhibition of cationic mixing and the release of lattice oxygen et al. Subsequently, it outlines various strategies to enhance the performance of Co-lean/free materials, such as ion doping, including single-ion doping and multi-ion co-doping, and various surface coating strategies, so as to eliminate the adverse effects of Co loss on materials. Ultimately, this paper offers a glimpse into the promising future of Cobalt-free strategies for high performance of Nickel-based layered transition metal oxides.

25 ENERGY STORAGE↗
DOE OSTI2023

Measuring Q₀ in LCLS-II Cryomodules Using Helium Liquid Level

The nitrogen-doped cavities used in the Linac Coherent Light Source II (LCLS-II) cryomodules have shown an unprecedented high Q₀ in vertical and cryomodule testing compared with cavities prepared with standard methods. While demonstration of high Q₀ in the test stand has been achieved, maintaining that performance in the linac is critical to the success of LCLS-II and future accelerator projects. The LCLS-II cryomodules required a novel method of measuring Q₀, due to hardware incompatibilities with existing procedures. Initially developed at Jefferson Lab during cryomodule acceptance testing before being used in the tunnel at SLAC, we use helium liquid level data to estimate the heat generated by cavities. We first establish the relationship between the rate of helium evaporation from known heat loads using electric heaters, and then use that relationship to determine heat from an RF load. Here we present the full procedure along with the development process, lessons learned, and reproducibility while demonstrating for the first time that world record Q₀ can be maintained within the real accelerator environment.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Probing exchange bias at the surface of a doped ferrimagnetic insulator

With the realization of stress-induced perpendicular magnetic anisotropy, efficient spin-orbit torque switching, and room temperature topological Hall effect, interest in rare earth iron garnets has been revived in recent years for their potential in spintronic applications. In this study, we investigate the magnetic properties of micrometer-thick Bi and Ga substituted thulium iron garnets (BiGa:TmIG) grown by the liquid-phase epitaxy method. Above the magnetization compensation (MC) temperature, anomalous triple hysteresis is observed in BiGa:TmIG/Pt heterostructures by anomalous Hall effect measurements. X-ray magnetic circular dichroism and energy dispersive spectroscopy measurements reveal its origin as an internal exchange bias (EB) effect arising from inhomogeneities localized at the surface of the film. Possibly depending on the difference in thickness and defect realization of the EB layer, two types of magnetization reversal mechanisms, namely, the Stoner-Wohlfarth type and the reversible domain-wall motion type, are observed. Furthermore, our results show that rich meta-magnetic phases exist in garnets close toMC, which can be robustly tuned by chemical composition engineering and conveniently probed by electrical transport measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Simultaneously improved reversibility and hydrogen production of solid oxide cells through infiltrating air electrode

Among the various fuel cells, solid oxide cells (SOCs) are the unique type that can principally operate reversibly as either fuel cells to produce electricity or as an electrolyser to split water and produce green hydrogen (H 2 ). Nevertheless, the SOCs' reversibility presents enormous challenges that are manifested by the fast degradation through the cycling between fuel cell and electrolysis mode. While the La 0.8 Sr 0.2 MnO 3 /yttria-stabilized zirconia (LSM/YSZ) air electrode possesses significant advantages in terms of high electrical conductivity and high thermal stability under fuel cell mode, the SOCs with the LSM/YSZ air electrode experience rapid performance degradation with catastrophic electrode delamination shortly after switching from fuel cell to electrolysis mode. To prevent such catastrophic delamination and enable the electrolysis H 2 production, a chemical solution with the designed chemistry of SrFe 2 O 4-d was infiltrated into the LSM/YSZ air electrode. The infiltration immediately mitigates the catastrophic delamination, and the infiltrated cells exhibit significantly improved reversibility upon the electrochemical operation. Nanostructure examination reveals nanoscale cracks and second-phase nanograins formed in the air electrode from the baseline cell. By contrast, no delamination was observed at either the micron or the nanoscale for the infiltrated cell, which is attributed to the increased ion conductivity of the Fe-doped LSM mixed conductor induced by the significant interdiffusion between the LSM backbone and infiltrates. Here, this study presents a viable method for preventing electrode delamination while enhancing the durability of H 2 production and power generation for reversible fuel cell/electrolysis cell operation. It further opens new research directions of modifying the electrochemical activity of the electrode of inherently functional cells through the infiltration of the solutions with different chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Robust highly durable solid oxide fuel cell cathodes – Improved materials compatibility & self-regulating surface chemistry

Solid oxide fuel cells (SOFCs) are electrochemical conversion devices that directly transform hydrogen or hydrocarbon fuels to electricity, with energy efficiencies as high as 90%, coupled with reduced emissions. Several factors, however, remain to be addressed when considering scale-up of SOFC technology, including the need to overcome decreased performance due to sluggish rates of the oxygen reduction reaction (ORR) at the cathode under reduced temperatures and susceptibility to degradation in performance from surface poisoning e.g. from chromia, while limiting the use of critical raw materials (lanthanides and transition metals) present in high performing mixed ionic electronic conducting electrodes like (La,Sr)CoO 3 (LSC). In this project we explored the key descriptors for determining ORR activity in SOFC electrodes and tried to recover performance degradation by applying them to SOFC electrodes. In order to do this, we first selected a model mixed ionic electronic conducting (MIEC) oxide, Pr-doped CeO 2 (Pr 0.1 Ce 0.9 O 2-δ , PCO), which is a chemically stable fluorite and free of inherent poison sources (e.g. Sr segregation in LSC) that potentially react with external impurities such as Cr-species vaporized from the interconnect. The three approaches originally planned in this project are as follows: 1) evaluation of scavenger exsolution characteristics, 2) study of scavengers gettering efficacy following Cr and Si poisoning and 3) integration of new compositions into porous electrodes. Among them, exceptional progress has been made in 2) and 3), especially understanding the role of surface infiltrants in impacting electrode performance and degradation of PCO materials. We found that the Smith acidity scale for binary oxides serves as a powerful descriptor for tuning and predicting the oxygen exchange kinetics on MIEC PCO surfaces. As a result, with infiltration with binary oxides, ranging from strongly basic (Li 2 O) to strongly acidic (SiO 2 ) onto the surface of porous PCO, it was possible to systematically vary the chemical surface exchange coefficient (k chem ) by 6 orders of magnitude! L i2 O increased k chem by nearly 1,000 times over that of pristine PCO, while SiO 2 decreased k chem by nearly the same factor. Strikingly, although the pre-exponential of k chem scales linearly with the acidity of the infiltrated binary oxide, there is nearly no change in the activation energy. With this insight, we attributed the origin of these dramatic changes in k chem values to the systematic increase and decrease in the surface electron density induced by infiltrated binary oxides. More interestingly, although both Cr 2 O 3 and SiO 2 were determined to be acidic by Smith, suggesting that this feature could likely be the primary reason that these compounds serve to poison the ORR on SOFC cathodes, the effect of poisoning could be subsequently tuned by adding multiple infiltrants and controlling their relative surface acidities. We also systematically examined the effect of serial infiltration of basic and acidic oxides. It turned out that serial infiltration of Li not only recovers approximately 20-fold degraded k chem of PCO by acidic Cr 2 O 3 but its k chem is enhanced even beyond that of the non-infiltrated PCO by more than three orders of magnitude. This was further verified with a screen-printing PCO symmetric cell in terms of the electrode performance (area-specific resistance, ASR) related to approach 3). These observations point to acidity as a key descriptor not only in tuning and predicting the ORR activity of SOFC cathodes that largely determines the overall performance of SOFC, but in mitigating and reactivating poisoned electrode performance. This work provides novel guidelines for making the electrode performance much more active and robust in SOFCs, which can further be applied to all applications requiring oxygen exchange reaction, such as electrolyzers, permeation membranes and gas sensors.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Contactless Production Testing of Silicon Solar Cells

Critical cost reductions in silicon solar cells are made by minimizing silver usage in their metal contacts. The reason why is both clear and unavoidable—silver is not only expensive, but also a potential limiting resource for scale-up (the PV industry alone used 10.3 % of the global silver supply in 2020 [1]). The result is solar cells with vanishing electrical contact area that are extremely difficult to test prior to module manufacture, when they must be sorted for quality to maximize power output and reliability of the subsequent modules. This project developed a new measurement instrument that enables the transition to solar cells with very low silver content, including cell designs with both minimal busbars and no busbars at all to electrically contact. The resulting instrument at project completion demonstrated the ability to sort cells with comparable—or better—results than existing technology. Compared to existing cell-test instruments, the new tool has minimal contacting requirements, which lowers the maintenance costs and use of consumable parts. We demonstrated innovative, yet pragmatic, solutions for reporting a comprehensive set of measurement results useful for both cell sorting (going forward in the line for module manufacture) and process control (looking backward in the line to identify cell manufacturing issues from wafer to cell-test). In addition to the traditional current-voltage characterization at cell test—short circuit current, open-circuit voltage, power, efficiency and fill factor—the new tool maintains all the advanced parameter characterization of our existing product line such as a substrate doping measurement, carrier recombination (lifetime) analysis, and surface recombination analysis.

14 SOLAR ENERGY↗
DOE OSTI2023

Improved cell performance and sulphur tolerance using A-site substituted Sr2Fe1.4Ni0.1Mo0.5O6–δ anodes for solid-oxide fuel cells

Abstract Solid-oxide fuel cells (SOFCs) offer great promise for producing electricity using a wide variety of fuels such as natural gas, coal gas and gasified carbonaceous solids; however, conventional nickel-based anodes face great challenges due to contaminants in readily available fuels, especially sulphur-containing compounds. Thus, the development of new anode materials that can suppress sulphur poisoning is crucial to the realization of fuel-flexible and cost-effective SOFCs. In this work, La0.1Sr1.9Fe1.4Ni0.1Mo0.5O6–δ (LSFNM) and Pr0.1Sr1.9Fe1.4Ni0.1Mo0.5O6–δ (PSFNM) materials have been synthesized using a sol-gel method in air and investigated as anode materials for SOFCs. Metallic nanoparticle-decorated ceramic anodes were obtained by the reduction of LSFNM and PSFNM in H2 at 850°C, forming a Ruddlesden–Popper oxide with exsolved FeNi3 bimetallic nanoparticles. The electrochemical performance of the Sr2Fe1.4Ni0.1Mo0.5O6–δ ceramic anode was greatly enhanced by La doping of A-sites, resulting in a 44% decrease in the polarization resistance in reducing atmosphere. The maximum power densities of Sr- and Mg-doped LaGaO3 (LSGM) (300 μm) electrolyte-supported single cells with LSFNM as the anode reached 1.371 W cm −2 in H2 and 1.306 W cm–2 in 50 ppm H2S–H2 at 850°C. Meanwhile, PSFNM showed improved sulphur tolerance, which could be fully recovered after six cycles from H2 to 50 ppm H2S–H2 operation. This study indicates that LSFNM and PSFNM are promising high-performance anodes for SOFCs.

Li, Haixia↗
DOE OSTI2026

Understanding Defect Activation and Kinetics in Next Generation CdTe Absorbers

This project investigated the role of defects and dopants in cadmium telluride (CdTe) solar cells to improve efficiency and long-term stability. Advanced X-ray microscopy and spectroscopy techniques were used to map composition, identify defect structures, and measure charge collection at the nanoscale. These experimental results were combined with computational modeling to understand how dopants such as copper and arsenic interact with other elements during processing. The study found that many dopants become electrically inactive due to the formation of complexes with chlorine and oxygen, limiting carrier concentration and device performance. It also showed that selenium, used to enhance efficiency, can migrate within the material during both manufacturing and operation, altering local structure and potentially affecting stability. The project developed new diagnostic and analysis tools for studying photovoltaic materials and provided a mechanistic understanding of key performance limitations. These insights support the development of more efficient, stable, and cost-effective CdTe solar technologies for large-scale energy deployment.

14 SOLAR ENERGY↗
DOE OSTI2021

DEVELOPMENT OF STABLE ANODE AND CATHODE MATERIALS FOR RECHARGEABLE BATTERIES

Batteries have been employed in a variety of applications, such as portable electronics, electric vehicles (EVs), and stationary energy storage to preserve energy from other renewable sources (like wind or solar energy). The ultimate goal is to develop high energy density, long life span, better safety, and low cost of the batteries. However, current commercialized batteries (like lead-acid, zinc-alkaline, lithium-ion batteries (LIBs)) could not fulfill all the demands of diversified applications. LIBs predominate the market because of their high energy density. To achieve a higher capacity of the cell, high-nickel layered (Ni > 90%) cathode materials are promising candidates since they compose high specific capacity and discharge voltage. In chapter 1, an introduction to cell energy density and the development of high-nickel layered cathode materials along with associated obstacles of poor cycling stability and thermal stability have been discussed. Associated works like doping or surface coating have also been mentioned in this section. In chapter 2, Al doping in high-nickel layered cathode materials to enhance the structural and thermal stability was introduced. Uniform incorporation of Al doping is achieved by mechanical fusion and calcination processes. The Al doping not only decreased the Li/Ni mixing ratio but also enhance the thermal resistance to oxygen evolution because of strong Al-O bonding, which leads to elevated electrochemical and thermal stability. In chapter 3, TiN is implemented as a Ti dopant for high-nickel layered cathode materials to improve the electrochemical performance in the LIBs. The Ti not only diffused within the bulk structure but also formed segregation on the surface, which improved the structural stability and led to better cycling performance. Although LIBs deliver high energy density, safety concerns of flammable organic electrolytes have not been resolved yet. Therefore, the aqueous rechargeable zinc-ion batteries (ZIB) have been praised for their safe, low-cost, eco-friendly stationary energy storage, which is considered as a complementary system to LIBs. In chapter 4, the mechanism, advantages, and challenges of ZIBs would be given and the strategies for solving the zinc metal anode issues have been discussed in this section. In chapter 5, a polymer coating method was reported to facilitate Zn deposition/ stripping by coordination with Zn2+ and prevented direct contact with aqueous electrolyte to block corrosion side-reactions. With this coating, a boost in a lifetime (up to 400 hours) and lower polarization under extremely high current conditions (10 mA cm-2) have been achieved in repeated Zn deposition/ stripping cycling.

25 ENERGY STORAGE↗
DOE OSTI2023

Influence of the Ozone Dose Time during Atomic Layer Deposition on the Ferroelectric and Pyroelectric Properties of 45 nm-Thick ZrO 2 Films

Over a decade ago, ferroelectricity was discovered in doped HfO 2 thin films. The HfO 2 -based thin films have attracted much attention due to their remarkable scalability and CMOS compatibility. Other than the HfO 2 -based thin films, the undoped ZrO 2 thin films are understudied despite their commonly reported antiferroelectric behavior. However, being of the same fluorite structure as HfO 2 -based thin films, the undoped ZrO 2 also displayed considerable ferroelectricity as demonstrated in recent studies. Here, 45 nm-thick polycrystalline undoped ZrO 2 films are synthesized using atomic layer deposition with different ozone dose times. The ZrO 2 films are crystallized after atomic layer deposition at 350 °C without anneals. In general, the longer ozone dose time causes a lower in-plane tensile stress and oxygen vacancy content, which help facilitate an irreversible non-polar tetragonal to polar orthorhombic phase transition with electric-field cycling. However, the lower in-plane tensile stress and oxygen vacancy content also stabilize the monoclinic phase so that a long ozone dose time (>17.5 s) reduces the ferroelectric behavior. After wake-up cycles, the ZrO 2 thin film with an ozone dose time of 17.5 s exhibits a remanent polarization of 6 μC·cm –2 and a pyroelectric coefficient of -35 μC·K –1 ·m –2 . Moreover, the wake-up behavior is consistent between the ferroelectric and pyroelectric response. As essential factors in optimizing the growth of fluorite-structure thin films for ferroelectric applications, the in-plane tensile stress and oxygen vacancy content significantly influence the ferroelectric and pyroelectric properties. Additionally, the low thermal budget for processing ferroelectric ZrO 2 thin films is valuable for semiconductor back-end-of-line processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗