Search NASA⌕ Search

SEARCH · Search NASA

Results for “Energy Deposition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Directed energy deposition of Haynes 282 nickel superalloy

Laser powder directed energy deposition was employed to fabricate Haynes® 282 Ni-based superalloy for high temperature creep testing. Material was heat treated using a single-step aging heat treatment of 800 °C for 4 h. Microstructural analysis was conducted in the as-deposited, solution-annealed, and age-hardened conditions. γ′ precipitates were absent in the as-deposited and annealed condition but formed during aging with an average size of 48.5 ± 12 nm. γ’ denuded zones ranging in thickness from 73 to 469 nm were observed adjacent to an effectively continuous grain boundary carbide film that covered 72.5% of the measured boundary length. The heat-treated material contained a high-volume fraction of TiC carbides ranging in size from 38 to 457 nm. Electron backscatter diffraction showed partial recrystallization, with 77-83% recrystallized area and a heterogeneous grain-size distribution. Creep testing at 750 °C at 300, 320, and 350 MPa revealed significantly inferior performance compared to wrought material, with higher strain rates, earlier tertiary onset, and shorter rupture lives. Fractography shows that failure was dominated by intergranular rupture. Post rupture microstructural analysis results suggest that the creep behavior was primarily governed by the non-equilibrium interface network rather than the bulk γ/γ’ matrix. In conclusion, the findings indicate that achieving wrought-like creep performance necessitates substantial improvements in the additive process, specifically focusing on enhanced homogenization, full recrystallization, and precise control over the morphology and distribution of carbides.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Investigation of residual stress distribution in wire-arc directed energy deposited refractory molybdenum alloy utilizing numerical thermo-mechanical analysis and neutron diffraction method

Directed energy deposition (DED), a metal additive manufacturing (AM) technique, offers higher deposition rates and energy efficiency, making it suitable for fabricating components from refractory molybdenum alloys, such as molybdenum-titanium-zirconium (TZM). However, large thermal gradients and non-equilibrium thermal cycles in DED could generate high residual stress in the component, potentially deteriorating quality and performance. Thus, this study aims to investigate residual stress generation and its distribution in wire-arc DED of TZM thin-wall, utilizing thermo-mechanical analysis and high-fidelity neutron diffraction (ND) method. Two interpass temperatures (50°C and 200°C) have been considered to investigate their impact on residual stress formation. During experiments, in-situ thermal data has been recorded using thermocouples, which have been utilized for calibrating the thermal model. Thermocouple data shows a good agreement with the simulation results, having a difference of less than 10 %. Post-deposition part deformation has been observed, which is measured using a coordinate measuring machine, showing maximum values of 0.93 mm and 0.78 mm for interpass temperatures of 50°C and 200°C, respectively. Numerical predictions of distortion deviated by less than 15% from the experimental results. ND measurement and simulation results indicate that residual stress magnitude and evolution vary across the TZM deposits, revealing microstructural anisotropy in both conditions. Notably, lower interpass temperatures resulted in higher residual stresses, confirmed by experimental and simulation data. Further, this study demonstrated that an integrated experimental and thermo-mechanical analysis can potentially reveal the temperature history, part deformation, and residual stress formation in wire-arc DED TZM alloy.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Energy deposition and K-shell ionization of supernovae

We present explicit evaluation of K-shell ionization caused by photoelectric absorption, by Compton scattering, and by electron collisions in supernovae envelopes. Each process derives from the radioactivity that dominates the bolometric luminosity of the model supernovae. We include the ionization by bremsstrahlung. We find that electron-collision ionization with decelerating Compton electrons is the dominant process of K-shell ionization for light elements (lighter than Si) whereas photoelectric K-shell absorption of Comptonized gammas is the dominant process of K-shell ionization for heavy elements (like Fe). The relative importance of the ionization processes also depends upon composition and upon time, as well as upon supernova type. For Type Ia all four ionization sources are of importance. We present fitting formulas for the deposition of radioactive power in each class of models studied. The energy deposition of all mechanisms decreases with time, including the rate of K-shell ionizations of all elements throughout the supernovae model evaluated herein. We compare the relative contributions to the energy deposition and confirm with greater numerical detail results already established.

The, Lih-Sin↗
NASA NTRS1979

Energy deposition in the earth's atmosphere due to impact of solar activity-generated disturbances

Energy deposition in and dynamic responses of the terrestrial atmosphere to solar flare-generated shocks and other physical processes - such as particle precipitation and local heating - are investigated self-consistently in the context of hydrodynamics, the problem being treated as an initial boundary-value problem. It is extremely difficult to construct a general model for the line solar activity-magnetosphere-atmosphere; however, a limited model for this link is possible. The paper describes such a model, and presents some results on energy deposition into the earth's atmosphere due to solar activity-generated disturbances. Results from the present calculations are presented and discussed.

Wu, S. T.↗
DOE OSTI2022

Property-structure-process relationships in dissimilar material repair with directed energy deposition: Repairing gray cast iron using stainless steel 316L

Directed energy deposition (DED) based remanufacturing leverages the flexibility of additive manufacturing to add value to broken or worn components. DED offers the ability to repair cast iron, a material difficult to repair with traditional welding techniques. Despite this, development of appropriate DED process conditions for bimetallic cast iron structures lags low- and medium-carbon steel repair. Thermal stresses and porosity generated by high-temperature deposition on cast iron often lower mechanical properties and hinder the qualification process. In this report scanning speed, powder mass flow rate, and stepover width are studied in multiple-track structures deposited on gray cast iron. Dilution and residual stresses are found to be highly dependent on the selected process parameters. Samples with a higher volumetric energy input, e.g., slower scanning speeds and higher powder feed rates, showed improved density and lower residual stresses but suffered lower dilution into the substrate. The presented conditions further the development of additive manufacturing technologies for automotive repair.

42 ENGINEERING↗
DOE OSTI2023

NED_Asteroid_Energy_Deposition

In the event of a potentially catastrophic asteroid impact, with sufficient warning time, deploying a nuclear device remains a powerful option for planetary defense if a kinetic impactor proves insufficient. Predicting the effectiveness of a potential nuclear deflection or disruption mission depends on accurate multiphysics simulations of the device's x-ray energy deposition into the asteroid and the resulting material ablation. These simulations span many orders of magnitude, require a variety of different complex physics packages, and are computationally expensive. Having an efficient and accurate way of modeling this system is necessary for exploring a mission's sensitivity to the asteroid's range of physical properties. To expedite future simulations, we present a completed x-ray energy deposition model developed using the radiation-hydrodynamics code Kull which can be used to initiate a nuclear mitigation mission hydrocode. The model spans a wide variety of possible mission initial conditions: four different asteroid-like materials (Silicon Dioxide, Forsterite, Iron, and Ice), two different source spectra (1 and 2 keV blackbodies), and then a broad range of radiation fluences (0.0001 to 1 kt per square meter), source durations (10 to 100 ns), and asteroid porosities (0 to 80 percent). Using blowoff momentum as the primary metric, the modelinitiated simulation results match the full radiation-hydrodynamics results to within 10 percent. Please reference the journal article: Burkey et al., X-Ray Energy Deposition Model for Simulating Asteroid Response to a Nuclear Planetary Defense Mitigation Mission, Planetary Science Journal, (2023) for more information.

Managan, RobertA↗
DOE OSTI2023

A Prediction Method for Catchment Efficiency Loss due to Coaxial Nozzle Wear in Powder Fed Directed Energy Deposition Systems

Abstract Powder fed laser directed energy deposition systems show significant promise and their widespread adoption could greatly advance manufacturing technology; however, a significant amount of gas atomized metal powder is wasted during material deposition. As contaminated powder must be collected and disposed of as hazardous waste, this process is often criticized for its low catchment efficiency. This presents potential implementation and scaling issues, as widespread use of this technology would directly increase the amount of contaminated powder in need of safe disposal. A direct contribution to this waste issue was identified in past work as wearing exterior and interior surfaces on a replaceable nozzle component within the additive head of such a system integrated into a hybrid manufacturing machine tool. A computational fluid dynamics simulation is developed specifically for use within the manufacturing process by predicting catchment efficiency losses before a deposition operation is performed. The model is robust enough to calculate a catchment efficiency estimate within a reasonable transition time before deposition and is designed to replace visual estimation of nozzle deterioration by the machine operator. Both of two previously identified wear modes are represented in the simulation. Their effects on powder stream geometry are discussed in detail and the results are compared with in-situ measurements of powder stream geometry and concentrations. The resulting work contributes to the growing understanding of using prediction and prevention methods on catchment efficiency related part defects within these systems.

DeWitte, Lisa↗
DOE OSTI2021

In-situ digital image correlation and thermal monitoring in directed energy deposition additive manufacturing

As in welding, directed energy deposition (DED) additive manufacturing (AM) generates complex residual stresses and distortions commensurate with the complexity of the scan pattern used for deposition. To date, measuring DED distortions on complex geometries has only been achieved post process, discarding the complex thermomechanical history that leads to that final material state. In this work, surround stereo digital image correlation (DIC) is used to 3D map surfaces and strain tensors in-situ in a powder-blown laser DED system. Infrared thermography is then projected onto these surfaces to record the full thermomechanical history of printed parts. DIC presents a unique challenge to DED AM, as no part exists at the beginning of deposition, which (a) prevents application of an appropriate speckle pattern and (b) denies the user a zero strain reference frame. Solutions to these problems are proposed and their limitations explored herein. In sum, this work presents a relatively low-cost solution to monitoring and optimizing the unique temporal artifacts induced by complex scan strategies that was previously unobtainable.

42 ENGINEERING↗
DOE OSTI2020

Fast electron transport dynamics and energy deposition in magnetized, imploded cylindrical plasma

Inertial confinement fusion approaches involve the creation of high-energy-density states through compression. High gain scenarios may be enabled by the beneficial heating from fast electrons produced with an intense laser and by energy containment with a high-strength magnetic field. Here, we report experimental measurements from a configuration integrating a magnetized, imploded cylindrical plasma and intense laser-driven electrons as well as multi-stage simulations that show fast electrons transport pathways at different times during the implosion and quantify their energy deposition contribution. The experiment consisted of a CH foam cylinder, inside an external coaxial magnetic field of 5 T, that was imploded using 36 OMEGA laser beams. Two-dimensional (2D) hydrodynamic modelling predicts the CH density reaches 9.0 g cm − 3 , the temperature reaches 920 eV and the external B-field is amplified at maximum compression to 580 T. At pre-determined times during the compression, the intense OMEGA EP laser irradiated one end of the cylinder to accelerate relativistic electrons into the dense imploded plasma providing additional heating. The relativistic electron beam generation was simulated using a 2D particle-in-cell (PIC) code. Finally, three-dimensional hybrid-PIC simulations calculated the electron propagation and energy deposition inside the target and revealed the roles the compressed and self-generated B-fields play in transport. During a time window before the maximum compression time, the self-generated B-field on the compression front confines the injected electrons inside the target, increasing the temperature through Joule heating. For a stronger B-field seed of 20 T, the electrons are predicted to be guided into the compressed target and provide additional collisional heating. This article is part of a discussion meeting issue ‘Prospects for high gain inertial fusion energy (part 2)’.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Strength-ductility synergy through microstructural and compositional heterogeneity in directed energy deposition additive manufacturing of face-centered cubic materials

Directed energy deposition (DED) is an additive manufacturing (AM) process based on welding technology and offers the advantages of large build volume, high deposition rate, and ability to fabricate multi-material parts. Epitaxial continuous columnar grain growth is a characteristic microstructural feature of DED processed alloys. In this study, a bamboo-like microstructure (periodic alternation of equiaxed and columnar structure) was produced by adopting an intermittent deposition strategy in 316L stainless steel and Inconel 625. The formation of a bamboo-like alternating microstructure was confirmed through electron backscattered diffraction (EBSD) analysis. Hardness mapping showed that the columnar to equiaxed transition (CET) occurred at the region right below the fusion line. A finite element (FE) model was used to investigate the relationship between the temperature gradient (G) and the solidification rate (R). The FE model showed a low G/R ratio at the region right below the interface promoting the CET. The grain size and material-dependent deformation behaviors are analyzed using digital image correlation (DIC). The lower deformation on the fine-grain regions observed in DIC analysis is attributed to a higher strain hardening rate, which is confirmed through dislocation density analysis on a tensile-interrupted specimen. The periodically alternating grain size coupled with the microstructural changes caused by intermittent deposition strategy result in a better strength-ductility synergy in both single-material and bimetallic specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Tailoring material microstructure and property in wire-laser directed energy deposition through a wiggle deposition strategy

Developing effective strategies to directly control material microstructure, property, and anisotropy is an active research area in metal additive manufacturing. This work develops a wiggle deposition pattern for wire-laser directed energy deposition (DED) of 316L stainless steel (SS) to modify the solidification texture, particularly in the building direction, in as-deposited samples. Through multi-physics simulation, operando near-infrared imaging, and synchrotron x-ray characterization, it is found that the wiggle deposition strategy induces highly dynamic melt flow and oscillating thermal gradient in the melt pool, which is responsible for the variation of preferable grain growth direction and crystallographic texture in the sample. The specific texture reduces the anisotropy in the tensile strength of as-printed 316L SS samples cut along different directions. Also, it largely increases the ductility along the build direction. Crystal plasticity simulation is performed to correlate the sample texture with mechanical property. In conclusion, this work offers a unique approach for tailoring local properties through the control of melt pool instability by applying different tool paths.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Directed energy deposition additive manufacturing of functionally graded Al-W composites

Directed energy deposition using laser heat sources (DED-L) is a metal additive manufacturing method that can be used to fabricate functionally graded materials by feeding multiple powder streams directly into a laser-generated melt pool. Additionally, the composition can be spatially varied by independent control of the materials feed rates. DED-L additive manufacturing is used in this work to create continuously graded Al/W composites that span 0–55 vol% W in Al over length scales from 0.6 to 1.2 mm with individual layers on the order of 0.1 mm and powder particle sizes on the order of 10 µm. The obtained composition and thickness ranges are comparable to those typically achieved using conventional powder metallurgy approaches and enables fabrication of composites to be used as a high impedance graded density impactor (GDI) in dynamic ramp compression experiments to study matter under extreme conditions. DED-L additive manufacturing of a GDI presents an opportunity to reduce GDI fabrication time to less than a day compared to many weeks by conventional methods. It is also possible to scale the deposition by DED-L to essentially unlimited dimensions in the lateral directions, whereas conventional methods become limited.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-situ Nondestructive Evaluation of In-flight Particle Dynamics and Intrinsic Properties for Directed Energy Deposition

The objective of this exploratory project is to determine the feasibility of using laser diffraction, structured light 3D scanning, and x-ray diffraction for in-situ assessment and inspection of metal directed energy deposition (DED) that is applied to repair components such as engine parts in remanufacturing. During this project, we have successfully published or submitted at least one journal article for each subtask that we identified. One of our conference paper and presentation has won “best paper award” from Manufacturing & Design Division in the Institute of Industrial and Systems Engineers (IISE) Annual Conference 2021. Through this seed grant, we successfully validated the concepts and proved the three in-situ monitoring techniques work well to predict some defects generation during direct energy deposition. We submitted follow-up proposals to continue work on this topic.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Directed Energy Deposition Process Modeling, Validation, and Process-Informed Optimization

The directed energy deposition (DED) process, one of the most popular additive manufacturing techniques in use today, involves various complex physical mechanisms that are not yet well understood. In this regard, computational tools show promise for elucidating the manufacturing process and enabling nondestructive performance evaluations of manufactured parts. To better control and optimize the DED process?thereby improving the manufactured product? the present work develops and demonstrates a novel artificial intelligence (AI)-based process control and optimization technique. Specifically, a geometry-free thermo-mechanical model with adaptive subdomain construction is developed to accurately capture the material?s thermo-mechanical response under cyclical reheating and high cooling rates [1]. The model is demonstrated and validated with experimental measurements, in light of various geometries and processing parameters. Moreover, based on this thermo-mechanical model, a physics-informed reduced-order model is developed to enable quick predictions of the temperature field at every time step. Furthermore, an AI-based controller is developed that can adapt to the ever-changing system states by automatically adjusting the manufacturing process parameters. This entire work is based on the open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) [2] and its recent integration with Libtorch (the C++ frontend of PyTorch [3]). The combined development of the adaptive material deposition scheme, thermo-mechanical model, associated reduced-order model, and AI-based process controller carries great potential for improving advanced manufacturing processes.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Nanomechanical Characterization of Additive Manufactured GRCop-42 Alloy Developed by Directed Energy Deposition Methods

Propulsion applications such as combustion chambers and nozzles for liquid rocket engines require the use of unique materials with superior mechanical and thermal properties. GRCop-42(Cu-4 wt.% Cr-2 wt.% Nb) is one such candidate material developed by NASA and is now being manufactured using additive manufacturing (AM) techniques. AM offers a unique processing environment different from traditional metal fabrication processes. This study characterized the mechanical and structural properties of as-deposited and heat-treated GRCop-42manufactured with Blown Powder Directed Energy Deposition (BPD)based on preliminary testing. The materials were characterized using several techniques including surface profiling by laser microscopy, mechanical stiffness by instrumented indentation, crystal structure, residual stress measurements using XRD and residual XRD, and chemical composition and microstructural evaluation using SEM with EBSD. The results of the study are compared using the BPD techniques for samples in the as-deposited and heat-treated conditions.

GRCop-42↗
DOE OSTI2024

Process parameter translation strategies for variable directed energy deposition spot size using 316L, copper, and Inconel 625

Directed energy deposition (DED) is a form of additive manufacturing available across a variety of laser spot diameter values, often referred to as spot sizes. However, there is no method to easily transfer process parameters across discrete spot sizes, leading to DED process parameters that are equipment specific and not widely applicable. In this study, a strategy is proposed and investigated for five spot sizes that keep the areal energy density constant while varying power, feed rate, and powder flow during the deposition of 316L stainless steel. An assessment of trends in hardness and microstructure is possible due to the novel production of components of a single material across several spot sizes using a single nozzle on a single DED system. The proposed strategy was used to nullify the hardness drop during functional grading of Inconel 625 and pure copper, enabling fabrication of multi-material sample that does not compromise desirable properties. This application shows the value in establishing more efficient process parameter development and understanding spot size influences on geometric and material property flexibility, to enable a more diverse powder-based DED design space and to increase the industry adoption of DED systems.

316L↗
NASA NTRS2021

Segregation Evolution and Diffusion of Titanium in Directed Energy Deposited NASA HR-1

Titanium segregation in single-pass directed energy deposited (DED) NASA HR-1 is very difficult to control because grain size varies considerably and many large grains (>100 μm) are present. Therefore, homogenization kinetic analysis was performed to see how the homogenization process should be adjusted to mitigate titanium segregation. A basic model for titanium diffusion in NASA HR-1 was developed to project titanium segregation as a function of homogenization temperature, time, and grain size. The homogenization kinetic analysis provides a valuable reference on how the homogenization treatment should be adjusted to reduce titanium segregation to a very low level for DED NASA HR-1.

liquid rocket engine↗