Model-Based Design of Experiments for Temporal Analysis of Products (TAP): A Simulated Case Study in Oxidative Propane Dehydrogenation
Not Available
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
SEARCH · Search NASA
Results for “OXYGEN CONSUMPTION”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Amino-tethering synthesis strategy toward highly accessible sub-3-nm L1 0 -PtM catalysts for high-power fuel cells
Because of the poor accessibility of embedded active sites, platinum (Pt)-based electrocatalysts suffer from insufficient Pt utilization and mass transport in membrane electrode assemblies (MEAs), limiting their performance in polymer electrolyte membrane fuel cells. Here, we report a simple and universal approach to depositing sub-3-nm L1 0 -PtM nanoparticles over external surfaces of carbon supports through pore-tailored amino (NH 2 )-modification, which enables not only excellent activity for the oxygen reduction reaction, but also enhanced Pt utilization and mass transport in MEAs. Using a low loading of 0.10 mg Pt ∙cm -2 , the MEA of PtCo/KB-NH 2 delivered an excellent mass activity of 0.691 A∙mgPt -1 , a record-high power density of 0.96 W∙cm -2 at 0.67 V, and only a 30-mV drop at 0.80 A∙cm -2 after 30,000 voltage cycles, which meets nearly all targets set by the Department of Energy. Finally, this work provides an efficient strategy for designing advanced Pt-based electrocatalysts and realizing high-power fuel cells.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Resolving dynamic mineral-organic interactions in the rhizosphere by combining in-situ microsensors with plant-soil reactive transport modeling
Associations between minerals and organic matter represent one of the most important carbon storage mechanisms in soils. Plant roots are major sources of soil carbon, and resolving the dynamics and dominance of microbial consumption versus mineral sorption of root-derived carbon is critical to understanding soil carbon storage. Here we integrate in-situ rhizosphere microsensor and plant physiological measurements with a 3-D plant-soil reactive transport model to explore the fate of dissolved organic carbon (DOC) in the rhizosphere, particularly its microbial consumption and interaction with Fe oxide minerals. Over several days, a microdialysis probe sampling pore water at the root-soil interface of growing Vicia faba roots in live soil, revealed clear diel patterns of DOC concentration. Daytime DOC spikes coincided with peaks in leaf-level photosynthesis rates and were accompanied by declining redox potential and dissolved oxygen as well as increasing pH in the rhizosphere. Incorporating microsensor data into our modeling framework showed that the measured rapid loss of DOC after each mid-day spike could not be explained by consumption via aerobic respiration, nor via anaerobic respiration dominated by Fe oxide reduction. Rather, in the model, a large fraction of rhizosphere DOC was rapidly immobilized each day by adsorption to Fe oxides. Further, modeled microbial Fe reduction (fueled by DOC) did not mobilize significant organic carbon from Fe oxides during the day. Instead, the model predicted equilibrium desorption of organic carbon from Fe oxides at night. This new mechanistic modeling framework, which couples aboveground plant physiological measurements with non-destructive high-resolution monitoring of rhizosphere processes, has great potential for exploring the dynamics and balance of the various microbial reactions and mineral interactions controlling carbon transformations and storage in soils.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Consequence Analysis of Residual Water in a Storage Canister - 20484
Recent observations from projects sponsored under the DOE-Nuclear Energy Spent Fuel and Waste Disposition campaign show that residual free water, well above the 0.4 gm-moles that correspond to a 3 torr rebound pressure after a 30-minute hold following prototypic drying, may remain within SNF canisters used for long-term dry storage. Specifically, experimental observations in an Integrated Research Project showed subzero temperatures and a local pocket of frozen water in a mockup fuel assembly subjected to an industry practiced drying process. In gas sampling and analysis from the High Burnup (HBU) Demonstration project, using a fully loaded and dried SNF canister, indicated presence of 100 g of residual water had remained in the canister. The effects of residual water in terms of potential adverse impacts on the condition of the SNF and the canister internals during long-term dry storage has been rigorously evaluated to address inadvertent residual water contents. The impact of residual water on the fuel and canister internals, with a focus on the oxidation of the cladding and of postulated exposed (breached-clad) fuel, were evaluated using an integrated set of time-dependent environmental conditions with semi-empirical materials oxidation models. An 'integration model,' with coupled sub-models, developed and previously used by the Center for Nuclear Waste Regulatory Analysis (CNWRA), was applied and expanded with improved sub-models for water radiolysis, and for cladding and fuel oxidations. Cladding oxidation models for various alloys were developed using the rate constants for various cladding alloys in the dry storage temperature range. A burnup-dependent fuel oxidation model was developed; it accounted for inhibition effect of fission products on fuel oxidation rates. The potential for extension of the initial breach flaw (1 mm hole) was evaluated by two separate mechanics criteria. In the first case, a critical cladding strain criterion was used. In the second case, a critical stress intensity was used to evaluate stability of a planar axial flaw postulate. A failure condition exists when a sufficient amount of fuel oxidation (at the postulated breached-clad location) causes fuel pellet swelling to load the cladding to meet a mechanics criterion for flaw extension. The integration model's results provide the following insights. The radiolysis-generated oxygen is consumed with a partitioning between the cladding and the fuel. The extent of cladding oxidation is no more than 2 μm additional consumption of the cladding metal even with 10 moles of residual water, indicating that changes in cladding conditions due to water are expected to be negligible. The conditions for cladding failure (breach opening size extension) directly correlates with the extent of fuel oxidation. Fuel oxidation significant to extend the breach could occur even with 5.5 moles of residual water. The results indicate that fuel oxidation vis-a-vis cladding oxidation is more likely under a higher radiation field, i.e., when radiolytic decomposition of the residual water occurs in few years compared to several decades, and that the conditions to cause failure are increased with fuel and cladding temperatures approaching the peak storage temperature limit of 400 deg. C. (authors)
12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
Twinning Enhances Efficiencies of Metallic Catalysts toward Electrolytic Water Splitting
Twinning is demonstrated to be an effective way of enhancing efficiencies of metallic catalysts toward electrolytic water splitting. Dendritic Cu possessing dense coherent nanotwin (NT) boundaries (NTCu-5nm) is successfully prepared with an organic-assisted electrodeposition at high pulse current densities. NT boundaries significantly improve electrocatalytic efficiencies and stability of NTCu-5nm over nanocrystalline Cu (NCCu), reducing overpotentials at 10 mA cm -2 for the oxygen evolution reaction (OER) from 378 to 281 mV and from 235 to 88 mV for the hydrogen evolution reaction (HER), with a small chronoamperometric decay of 5% after 100 h continuous overall water splitting at an ultrahigh initial current density of 500 mA cm -2 , largely outperforming the large chronoamperometric decay of 27% for only 1 h operation of the NCCu//NCCu couple. The defective twin boundaries enable formation of active Cu III O 2 - at low overpotentials, thus enhancing OER performance. Furthermore, the synergistic geometric and electronic effects induced by the twin boundaries result in shifts in Gibbs free energies of hydrogen adsorption (ΔG H ) toward the apex of a volcano plot of exchange current density versus ΔG H , leading to the remarkable improvement in HER activity.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Ultra-Fast Non-Volatile Resistive Switching Devices with Over 512 Distinct and Stable Levels for Memory and Neuromorphic Computing
Low-current multilevel programmability with inherent non-volatility and high stability of resistance states is required for both multi-bit memory storage and deep learning accelerators but is difficult to achieve. Here, in a resistive switching system, this work realizes >512 (>9 bits) distinct non-volatile conductance levels with stable retention for each state with current levels down to the nanoampere range, highly promising for potential integration with small processing nodes with ultra-low power consumption requirements. This is achieved by demonstrating a new thin film design concept that encompasses three key features: an ultra-thin epitaxial oxygen ionic switching layer that provides a tunable energy barrier at the bottom electrode, an overcoat amorphous layer that acts as an ion migration barrier for stable state retention, and a partial conductive filament as a localized electronic transport channel to the epitaxial switching layer. A large dynamic resistance range of up to seven orders of magnitude is achieved with reset-free transitions among intermediate states, and programmability is demonstrated with ultra-fast (20 ns) pulses. Artificial neural network (ANN) simulations, based on the experimental performance and its non-idealities, demonstrate close-to-ideal inference accuracies for various Modified National Institute of Standards and Technology (MNIST) data sets.
36 MATERIALS SCIENCE↗
Tandem and Bimetallic Catalysts for Oxidative Dehydrogenation of Light Hydrocarbons with Renewable Feedstock
One of the grand challenges for national energy security is the establishment of sustainable chemical transformations. The chemical industry relies on naphtha feedstock from nonrenewable crude oil, and uses energy intense processes to make useful building block molecules such as ethylene through steam cracking, which generates significant greenhouse carbon dioxide emissions. Sustainable chemistry through selective catalysis should enable chemical transformations that use renewable feedstock such as nonfood biomass, minimize energy consumption, and do not emit greenhouse gases or other waste byproducts. In this research, we studied fundamental chemistry that couples the removal of oxygen atoms from nonfood biomass derived polyols and diols with oxidative dehydrogenation (ODH) of petroleum based alcohols. Heterobimetallic Re-Ir complexes were constructed and their reaction chemistry established. Typical substrates are glycerol, sugar alcohols and pentane to produce allyl alcohol, pentene, and water. The reaction mechanism of a recyclable rhenium nano-particle catalyst was established for deoxydehydration of sugar alcohols without the use of organic solvents.
09 BIOMASS FUELS↗
Oxygenates production in a microfluidic dielectric barrier discharge device sustained in Ar/CH 4 /O 2
Reforming of methane (CH 4 ) is a process to produce syngas (CO/H 2 ) and other value-added chemicals including oxygenates such as methanol (CH 3 OH). Atmospheric pressure plasmas have the potential to be more energy efficient than traditional reforming methods as value-added chemicals can be synthesized directly in the plasma without requiring an additional step. In this paper, we discuss the results from a computational investigation of the formation of oxygenates by CH 4 oxidation in the presence of Ar, including CH 3 OH and CH 2 O, in a nanosecond pulsed dielectric barrier discharge. The plasma is formed in a microfluidic channel whose small dimensions are ideal for plasma formation at atmospheric pressure. The production and consumption mechanisms of dominant radicals and long-lived species are discussed in detail for the base case conditions of Ar/CH 4 /O 2 = 50/25/25. CH 3 OH is produced primarily by CH 3 O reacting with CH 3 O and CH 3 O 2 reacting with OH, while CH 2 O formation relies on reactions involving CH 3 O and CH 3 . The most abundant oxygenate formed is CO (produced by H abstraction from CHO). However, the greenhouse gas CO 2 is also formed as a by-product. The effects of gas mixture are examined to maximize the CH 3 OH and CH 2 O densities while decreasing the CO 2 density. Increasing the Ar percentage from 0% to 95% decreased the CH 3 OH and CH 2 O densities. At low Ar percentages, this is due to an increase in consumption of CH 3 OH and CH 2 O, while at high Ar percentages (>40% Ar), the production of CH 3 OH and CH 2 O is decreased. However, both CO and CO 2 reached peak densities at 70%–90% Ar. Changing the CH 4 /O 2 ratio while keeping 50% Ar in the discharge led to increased CH 3 OH and CH 2 O production, reaching peak densities at 35%–40% CH 4 . The CO and CO 2 densities decreased beyond 20% CH 4 , indicating that a CH 4 rich discharge is ideal for forming the desired oxygenates.
03 NATURAL GAS↗
Increasing pyrolysis oil yields and decreasing energy consumption via thermal oxo-degradation of polyolefins
Commercialization of pyrolysis of plastics in an inert atmosphere is challenging due to large thermal requirements. This study employs thermal oxo-degradation and demonstrates how oxygen supplied at modest equivalence ratios can both accelerate depolymerization and provide the enthalpy for pyrolysis without dramatically impacting desired product yields. The enthalpies for pyrolysis of high-density polyethylene (HDPE) and polypropylene (PP) are measured to be 2,300 ± 90 J g – -1 and 2,800 ± 60 J g –1 , respectively. Using air as an oxygen source in a fluidized bed reactor, HDPE and PP are rapidly deconstructed while using up to 84% less energy through the energy released by partial oxidation. Characterization of the thermal oxo-degradation product oil shows comparable composition to conventional pyrolysis oil. Thermal oxo-degradation proves to be a promising technology for upcycling of plastics by improving thermal depolymerization of waste plastics and reducing energy requirements while maintaining desirable yields.
42 ENGINEERING↗
Advanced sorbents for modular oxygen production for REMS gasifiers
Under a DOE funded effort, Thermosolv LLC has been developing a sorbent-based oxygen production technology for gasification and oxy-combustion applications. The sorbents utilize oxygen-storage properties of certain perovskites to (1) selectively adsorb oxygen at moderate temperature from compressed air and (2) release the adsorbed oxygen into a vacuum or a sweep gas such as CO2 and/or steam. Through cyclic operations of multiple sorbent beds such a process can be made continuous. Pressure drop across the sorbent bed and other similar design considerations dictate that the sorbent be in the form of a high surface-area-to-volume pellet and yet still possess sufficient crush strength and integrity. Process efficiency is determined by the sorption and desorption kinetics and sorbent capacity. Typical process involves cycle times in the order of 100 seconds, a time too short to fully utilize the full volume of the sorbent and the sorption capacity of the sorbent pellets. As a part of this project, Thermosolv LLC undertook the development of oxygen sorbents as a high-surface area supported sorbent on a light-weight inert support to (1) reduce the cost, (2) increase the productivity, and (3) reduce the overall weight of the reactor. Using a previously developed perovskite (LSCF 1991) with its well-characterized performance, composite sorbent pellets each consisting of an inert core coated by a thin layer of the functional perovskite material were produced. Several low-density, inexpensive inert solids supports in the 1/8”-1/4” size were selected to keep the pressure drop across the sorbent bed in the acceptable range. A number of commercial technologies including spray coating, dip coating, incipient impregnation of porous substrate followed by thermal annealing at various temperatures and duration were employed and tested to produce robust composite supported sorbent pellets. A sense of optimum coating thickness was developed by testing sorbent pellets of various increasing diameter pellets. LSCF-1991extrudates ranging in size from 1/32” to 3/16” were tested in a TGA and in a fixed-bed pressure swing test set-up for sorption/desorption cycles of interest. The data show that for the operational conditions of interest the coating thickness for a supported sorbent pellet needs to be approximately 1/32” (about 0.8 mm). Subsequent work thereby concentrated on developing composite pellets of various substrates, shapes and sizes with coating layer of about this size range. Candidate support materials were chosen based on cost, inertness, mechanical strength, thermal expansion and chemical stability with sorbent material, and in a size range to give an acceptable pressure drop in fixed-bad reactor configurations. Coating application methods used for application of the sorbent onto the support included precipitation, spray coating and dip coating from sorbent slurries and sol gels. For all coated supports where we could successfully apply a uniform coating of desired thickness with an acceptable handling performance in terms of exfoliation, TGA-based cyclic sorption/desorption testing was performed to determine cycling capacity of oxygen. Among nearly twenty different support materials tested, best adhesion performance was obtained from stainless saddle supports. In the bench-scale fixed-bad tests stainless steel saddle support composite pellets with a coating thickness in the 0.6 mm or so range, the composite sorbent pellet performance approached up to 95% of that of the 2 mm parent material pellets. In a parallel approach to reducing the cost of the sorbent, alternate sorbent formulations replacing/reducing the amount of cobalt in the LSCF family were also investigated. Successful formulations that could match the performance of LSCF 1991 were identified based on TGA cyclic tests as LSCF 1919 and LSF 1910. In the range of operational envelop of cycle times and other relevant process operating conditions, the reduced Co formulations showed comparable performance in the bench-scale fixed-bad cyclic operations. As a part of this project, we also attempted substitution of La and Sr with Ca and Ba, and Co with Mn, Ni and Cu with little success, but the overall project goal of reducing sorbent cost in terms of raw material and manufacturing expenses was successful.
01 COAL, LIGNITE, AND PEAT↗
Production of hydrogen peroxide in an intra-meander hyporheic zone at East River, Colorado.
The traditionally held assumption that photo-dependent processes are the predominant source of H 2 O 2 in natural waters has been recently questioned by an increasing body of evidence showing the ubiquitiousness of H 2 O 2 in dark water bodies and in groundwater. In this study, we conducted field measurement of H 2 O 2 in an intra-meander hyporheic zone and in surface water at East River, CO. On-site detection using a sensitive chemiluminescence method suggests H 2 O 2 concentrations in groundwater ranging from 6 nM (at the most reduced region) to ~ 80 nM (in a locally oxygen-rich area) along the intra-meander transect with a maxima of 186 nM detected in the surface water in an early afternoon, lagging the maximum solar irradiance by ~1.5 h. Our results suggest that the dark profile of H 2 O 2 in the hyporheic zone is closely correlated to local redox gradients, indicating that interactions between various redox sensitive elements could play an essential role. Due to its transient nature, the widespread presence of H 2 O 2 in the hyporheic zone indicates the existence of a sustained balance between H 2 O 2 production and consumption, which potentially involves a relatively rapid succession of various biogeochemically important processes (such as organic matter turnover, metal cycling and contaminant mobilization). More importantly, this study confirmed the occurrence of reactive oxygen species at a subsurface redox transition zone and further support our understanding of redox boundaries on reactive oxygen species generation and as key locations of biogeochemical activity.
63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
Revealing the coupled oxygen and hypochlorite chemistry in saltwater batteries through operando pH and oxygen monitoring
Saltwater batteries (SWBs) that utilize Na⁺ ions from seawater have emerged as promising candidates for low-cost and sustainable grid-scale energy storage. To date, the cathode reaction mechanism of SWBs has been predominantly described by oxygen evolution and reduction reactions (OER/ORR). However, this assumption is valid only under idealized ocean-like conditions with constant pH and continuous oxygen replenishment. In practical systems, SWBs operate in finite volumes of saltwater, where saltwater composition dynamically evolves during cycling. Here, in this work, we systematically investigate the cathode reaction mechanisms of SWBs under finite saltwater conditions using galvanostatic cycling combined with electrochemical diagnostics and operando monitoring of dissolved oxygen and pH. Our results reveal that the cathode chemistry during SWB operation is considerably more complex than previously assumed. In addition to OER and ORR, hypochlorite formation and consumption reactions, along with pH-dependent switching of dominant reaction pathways, play critical roles. We further identify the sequence and relative contributions of these reactions throughout charge–discharge cycling. These findings provide a comprehensive and mechanistically grounded understanding of SWB cathode processes under relatively realistic cell design and operation condition. The insights presented here establish a new framework for interpreting SWB electrochemistry and offer directions for future strategies aimed at improving performance, stability, and practical viability.
Hypochlorite redox reaction↗
Platinum Group Metal Catalysts: Supply Chain Deep Dive Assessment
The report “America’s Strategy to Secure the Supply Chain for a Robust Clean Energy Transition” lays out the challenges and opportunities faced by the United States in the energy supply chain as well as the federal government plans to address these challenges and opportunities. It is accompanied by several issue-specific deep dive assessments, including this one, in response to Executive Order 14017 “America’s Supply Chains,” which directs the Secretary of Energy to submit a report on supply chains for the energy sector industrial base. The Executive Order is helping the federal government to build more secure and diverse U.S. supply chains, including energy supply chains. This report focuses on the supply chain for catalysts, specifically platinum group metal (PGM) catalysts, used for decarbonizing energy technologies. Catalysts are substances that increase the rate, conversion, and selectivity of chemical reactions and are used in a variety of applications such as chemical manufacturing, petroleum refining, and catalytic converters. Catalysts containing PGMs (“PGM catalysts”) are particularly useful in widespread industrial applications, including the production of high-volume chemicals such as ammonia, acetic acid, nitric acid, and the refining of crude oil into petroleum products. The PGM metals possess extraordinary properties such as being active oxidation and hydrogenation catalysts; excellent electrical conductors and electrodes; and outstanding adsorbers of oxygen and hydrogen. Within the energy industrial base, PGM catalysts improve the energy and materials efficiency of petroleum refining and chemical industry processes and reduce energy consumption in manufacturing. In addition to their use in catalytic converters, PGM catalysts are important to maximizing the efficiency of emerging decarbonization technologies, specifically in proton exchange membrane (PEM) electrolyzers for green hydrogen production from water and PEM fuel cells for transportation and stationary energy storage. Green hydrogen is expected to play a significant role in decarbonization scenarios.
29 ENERGY PLANNING, POLICY, AND ECONOMY↗
Precious metal oxygen-evolving anodes for electrolytic reduction of metal oxides in molten LiCl-Li 2 O electrolyte
Understanding the electrochemical stability of oxygen-evolving anode materials in molten salt electrolytes is essential to enable decarbonized electrolytic reduction of metal oxides (e.g., used nuclear oxide fuels). Here, this work investigated three precious metals (Ir, Ru, and Pt) as oxygen-evolving anodes in molten LiCl-Li 2 O (99.0-1.0 wt%) at 650 °C. For consistent measurements, this work employed a three-electrode cell comprised of a two-phase Li-Bi (65-35 at%) reference electrode and a NiO counter electrode. Anodic polarization behavior of each anode was investigated via cyclic voltammetry (CV) and chronoamperometry. The onset potential for oxygen evolution was observed at E > 2.9 V (vs. Li/Li + ) for the Ir and Ru anodes and anodic current density was as high as 1.0 A cm -2 at 3.23 V. The dimensional stability of each anode was evaluated from long-term electrolysis experiments (10.0-32.1 h) at 3.23 V. Rapid consumption of the Pt anode was observed after the application of 26,453 C cm -2 with a reduction in diameter of about 15.8% due to the formation of a non-protective Li 2 PtO 3 compound. The formation of this compound was also observed during CV measurements as additional anodic waves at potentials more negative than that of oxygen evolution. In contrast, both the Ir and Ru anodes exhibited excellent dimensional stability with a reduction in diameter or thickness of less than 1.5% even after applying greater charge density of ~41,100 C cm -2 , demonstrating superior stability during oxygen evolution in the LiCl-Li 2 O electrolyte.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Methyl formate oxidation kinetics up to 100 atm
Methyl formate (MF, CH3OCHO), the simplest ester, is a representative oxygenated fuel with high oxygen content, and low sooting tendency. However, its oxidation behavior under high-pressure and intermediate-temperature conditions remains insufficiently understood, especially where low-temperature peroxy radical chemistry, methanol chemistry, and pressure-dependent reaction pathways play a critical role. In this study, MF oxidation experiments were conducted in the Princeton supercritical-pressure jet-stirred reactor (SP-JSR) at 20 and 100 atm over the temperature range of 400–950 K under both fuel-lean and fuel-rich conditions. Based on the experimental results, an updated HP-Mech was developed by incorporating previous MF sub-mechanisms, expanded low-temperature peroxy pathways, and evaluated pressure-dependent decomposition kinetics. The newly updated HP-Mech shows greatly improved performance in predicting the onset temperature, the key intermediate species fractions, methanol formation, and the progression of MF oxidation across all the experimental conditions. Path flux analysis indicates that MF consumption at the onset stage is dominated by H-abstraction at the methyl site, forming CH2OCHO radicals that lead to the formation and isomerization of O2CH2OCHO, driving low-temperature chain propagation. Moreover, H-abstraction at the formate site forms CH3OCO radicals that preferentially decompose to CH3, initiating the methanol formation pathway linked to CH3O2 and HO2 chemistry. At the same time, HO2 formation is strongly coupled to MF oxidation through multiple MF-derived radical pathways. HCO originates from MF oxidation and acts as a key coupling species linking fuel consumption to HO2 buildup, especially under high-pressure and intermediate-temperature conditions. In addition to this dominant channel, supplementary HO2 formation pathways involving CH3, CH3O, CH2OH, and CH3O2 reacting with O2 further connect methanol chemistry and oxygenated radical chemistry to the HO2 pool, indicating the central role of HO2 in governing MF oxidation. Sensitivity analysis identifies MF with OH/HO2/CH3O2 reactions and the HO2/H2O2/OH sequence as the key factors controlling reactivity in the high-pressure and intermediate-temperature regime. MF directly reacts with OH/HO2/CH3O2 to consume the fuel and produce reactive radicals like CH2OCHO and CH3OCO that undergo subsequent oxidation pathways. Moreover, HO2 recombination suppresses oxidation at lower temperatures, while thermal decomposition of H2O2 accelerates OH production and promotes fuel consumption as temperature increases. The direct formation of active OH from HO2 radicals further completes the mechanism, improving its prediction especially during the oxidation onset stage.
Low-temperature Chemistry↗
Paternal preconception alcohol consumption increased Angiotensin II‐mediated vasoconstriction in male offspring cerebral arteries via oxidative stress‐AT1R pathway
Abstract Alcohol consumption is popular worldwidely and closely associated with cardiovascular diseases. Influences of paternal preconception alcohol consumption on offspring cerebral arteries are largely unknown. Male rats were randomly given alcohol or water before being mated with alcohol‐naive females to produce alcohol‐ and control‐sired offspring. Middle cerebral artery (MCA) was tested with a Danish Myo Technology wire myograph, patch‐clamp, IONOPTIX, immunofluorescence and quantitative PCR. Alcohol consumption enhanced angiotensin II (AngII)‐mediated constriction in male offspring MCA mainly via AT1R. PD123,319 only augmented AngII‐induced constriction in control offspring. AngII and Bay K8644 induced stronger intracellular calcium transient in vascular smooth muscle cells (VSMCs) from MCA of alcohol offspring. L‐type voltage‐dependent calcium channel (L‐Ca 2+ ) current at baseline and after AngII‐stimulation was higher in VSMCs. Influence of large‐conductance calcium‐activated potassium channel (BK C a ) was lower. Caffeine induced stronger constriction and intracellular calcium release in alcohol offspring. Superoxide anion was higher in alcohol MCA than control. Tempol and thenoyltrifluoroacetone alleviated AngII‐mediated contractions, while inhibition was significantly higher in alcohol group. The mitochondria were swollen in alcohol MCA. Despite lower Kcnma1 and Prkce expression, many genes expressions were higher in alcohol group. Hypoxia induced reactive oxygen species production and increased AT1R expression in control MCA and rat aorta smooth muscle cell line. In conclusion, this study firstly demonstrated paternal preconception alcohol potentiated AngII‐mediated vasoconstriction in offspring MCA via ROS‐AT1R. Alcohol consumption increased intracellular calcium via L‐Ca 2+ channel and endoplasmic reticulum and decreased BK Ca function. The present study provided new information for male reproductive health and developmental origin of cerebrovascular diseases.
Zhang, Ze↗
Transforming Aeration Energy in Water Resource Recovery Facilities (WRRFs) through Suboxic Nitrogen Removal (Final Report)
The objective of this project was to advance two key technological components—aeration control strategies and process design methodologies—to support the development and broader adoption of suboxic biological nitrogen removal (SBNR). The project focused on achieving the following three goals: • Enhance Model Predictive Control (MPC) Technology: Advance the DO/Nmaster MPC platform from its initial 2018 pilot deployment at the Chico Water Resource Recovery Facility in California to full-scale integration. This included partnering with a blower technology commercialization partner and incorporating machine learning (ML) capabilities to enable nationwide deployment. • Bridge Knowledge Gaps in SBNR Process Design: Address fundamental gaps in SBNR process understanding through controlled pilot-scale testing at a dedicated pilot facility. These efforts supported the development of robust kinetic models to inform reliable SBNR control, operational strategies, and design frameworks. • Demonstrate Full-Scale Implementation of Low DO/SBNR with ML: Transition low dissolved oxygen (DO)/SBNR coupled with ML from pilot-scale trials to full-scale demonstration in flow-through biological nutrient removal (BNR) systems, with the goal of enabling scalable, nationwide adoption in activated sludge treatment processes. The project included demonstration of SBNR at the pilot scale as performed by Hampton Roads Sanitation District (HRSD) and at the full-scale as performed by the Los Angeles County Sanitation Districts' (LACSD) Pomona Water Reclamation Plant (POWRP).
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Stable, high-performing bifunctional electrodes for anion exchange membrane-based unitized regenerative fuel cells
Anion exchange membrane unitized regenerative fuel cells (AEM-URFCs) are a promising technology for energy storage and electricity production; however, their efficiency is limited by the kinetics of the bifunctional oxygen electrode (BOE) where the oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) occur. A particular concern when designing the BOE is that the OER and ORR have differing catalytic requirements, which make it challenging to develop effective bifunctional electrocatalysts with single active sites. In this study, we focus on advancing the BOE performance using Pt-IrO x and Pt-NiCoO x electrocatalysts. Here, single-layer and dual-layer Pt-IrO x BOEs were made, with the dual-layer electrode leading to improved performance due to efficient catalyst utilization in both modes. Using the dual-layer oxygen electrode paired with a PtRu/C hydrogen electrode, a round trip efficiency (RTE) as high as 50% (62 %iR-free) was achieved at 500 mA/cm 2 and operation for more than 24 h, which included five one-hour-long H 2 generation and consumption cycles followed by one eight-hour-long cycle. To the best of our knowledge, this is the highest performance for AEM-URFCs reported to date. Lastly, the approach is extended to electrodes with a Pt loading of 0.5 mg/cm 2 and the IrO x substituted by NiCoO x .
25 ENERGY STORAGE↗