Search NASA⌕ Search

SEARCH · Search NASA

Results for “VOL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Highly Stable and Conductive 1,3‐Dioxolane/Hydrocarbon Based Electrolyte Solvent for Advanced Lithium‐Sulfur Batteries

Abstract Developing effective electrolytes is crucial for boosting the performance of Lithium‐Sulfur (LiS) rechargeable battery. Recent improvements in electrolyte formulations have enhanced cyclability by increasing electrochemical stability at the electrode interfaces. However, achieving both high ionic conductivity (σ) and stability at these interfaces simultaneously remains a significant challenge. In this study, we utilized a strategy to suppress polysulfide dissolution by employing a mixture of 1,3‐dioxolane (DOL) and hydrocarbon solvents with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) electrolyte salt. Compared to the conventional electrolyte solution, which is 1 M LiTFSI salt in a 50/50 vol % mixture of DOL and dimethoxy ethane (DME), the LiTFSI electrolyte with DOL/hydrocarbon solvents demonstrate better cycling stability, compatibility with the Li‐metal anode, and a high specific discharge capacity (Csp). Among the various DOL/hydrocarbon and LiTFSI electrolyte salts, the combination of DOL and n‐hexane, a linear hydrocarbon, with LiTFSI electrolyte salt, (DnH40LiTFSI) exhibits remarkable σ (6.5×10 −3 S/cm at 30 °C), compatibility with the Li‐metal anode, an initial Csp of ca. 1264 mAh/g, cycling stability (Csp and Coulombic efficiency are 811 mAh/g and 98.09 % after 120 cycles) at 0.1 C by forming a good protective layer on the Li‐metal surface and preventing polysulfide dissolution.

Ahmed, Faiz↗
DOE OSTI2026

Controlling Nb(IV) Defects in SrNbO 2 N Oxygen Evolution Photocatalyst by Ammonolysis With Dinitrogen–Ammonia Mixtures

Strontium niobium oxynitride (SrNbO 2 N) is a promising, corrosion resistant semiconductor for the visible light-driven water splitting reaction, a non-photovoltaic pathway to green hydrogen fuel. However, SrNbO 2 N materials made by ammonolysis usually contain Nb 4+ defect states that cause electron–hole recombination. Here, in this work, we demonstrate that such defects can be minimized by synthesizing SrNbO 2 N from metal oxides in a mixed 13%:87% (vol) NH 3 /N 2 atmosphere. According to electron paramagnetic resonance (EPR), SrNbO 2 N made in pure NH 3 contains paramagnetic impurities with g = 2.002 and 2.195, which can be assigned to lattice and surface Nb 4+ defects. These states also cause broad optical absorptions centered at 800 and 1020 nm, respectively, and the lattice defect produces a 1.55–1.63 eV signal in surface photovoltage spectra. The improved SrNbO 2 N contains five times fewer lattice Nb 4+ defects (8.95 × 10 15 cm −3 ), based on the integrated EPR signal intensity, and supports a water oxidation photocurrent of 1.07 mA cm −2 at 1.23 V versus RHE under simulated sunlight and an apparent quantum efficiency of 5.1% at 400 nm during photocatalytic oxygen evolution. Based on earlier results with LaTiO 2 N and BaTaO 2 N, dilution of NH 3 during synthesis appears generally beneficial to transition metal oxynitrides.

electron paramagnetic resonance↗
DOE OSTI2024

Additive manufacturing of sandwich panels with continuous fiber reinforced high modulus composite facings

Abstract An improved approach consisting of a combination of fiber placement and fused filament fabrication is introduced for the additive manufacture (AM) of structural grade sandwich beams. Here, sandwich beams are additively manufactured using in‐situ deposition and consolidation of continuous fiber unidirectional facings made from a commingled yarn system of e‐glass fiber (~50% vol.) and amorphous PET, and a hexagonal honeycomb core structure made from PETG. Both facings and the sandwich core are manufactured on a single machine, in one sequence (skin‐core‐skin), employing the benefit of matrix compatibility to create autohesion at the interfaces. Flexural and transverse shear rigidity are determined experimentally and compared with analytical predictions and show correlation to within 3%. Flexural strength and core shear strength are also measured. Post‐mortem examinations show that core fracture and core facing debond were the dominant failure mode in flexure. Single cantilever beam tests were performed to evaluate core facing debond toughness. Subsequently, surface preheat using infrared heaters was utilized to increase autohesion between core and facing. The results show debond toughness was increased 4 times using infrared heating. This research effort presents a manufacturing approach that has the potential for the AM of stiff, well bonded, structural grade sandwich beams, in an integrated sequence, employing in‐situ consolidation to the facings, without the need for the use of intermediate adhesives for skin‐to‐core bonding. Highlights An improved additive manufacturing technique for making sandwich panels is developed. Sandwich panel facings have fiber volume fractions of approximately 50%. Surface preheat improves core‐to‐facing debond toughness by a factor of 4. Top and bottom facings are consolidated during manufacture leading to better properties. Experimental results are compared to analytical predictions and show good correlation.

17 WIND ENERGY↗
DOE OSTI2025

In‐situ Analysis of Paste Properties in Resonant Acoustic Mixers for Quality Monitoring

Formulation control is key to achieving consistent target properties of energetic materials, as feedstock variations and slight deviations in the ratios of different ingredients can have major effects on final product properties, particularly in dense pastes with high particle loading >65 vol.%. In large‐scale operations, it is imperative to either correct or remove batches of material that perform outside baseline property specifications as early as possible to avoid unnecessary processing of suboptimal material. Quality monitoring is the practice of measuring material properties during processing using process analytical technologies as opposed to only testing the properties of the final product; it is a key principle in the quality‐by‐design frameworks used for designing formulations and manufacturing processes. Herein, a process analytical technology method for correlating material properties of dense pastes directly after mixing in a Resonant Acoustic Mixer to motor data is developed and used to detect differences in the particle content of dense paste formulations. This method was also capable of detecting variations in powder feedstock properties, such as particle packing efficiency, and is sensitive enough to detect changes of 2 wt.% in the total solids content of the formulation. The techniques presented herein show excellent promise for use as a process analytical technology capable of quantifying formulation effects on material movement modes during resonant acoustic mixing.

Materials science↗
DOE OSTI2024

A highly oxygen reduction reaction active and CO 2 durable high-entropy cathode for solid oxide fuel cells

One big obstacle for the oxygen reduction reaction (ORR) electrode in solid oxide fuel cells (SOFCs) is the poor reaction activity and fast degradations caused by CO 2 poisoning. Here, in this study, we report our design of an active A-site Ca-rich high-entropy Pr 0.1875 Ba 0.1875 Sr 0.1875 La 0.1875 Ca 0.25 CoO 3-δ (PBSLC 25 C) electrode, guided by the O p-band theory. Here, when applied as a cathode in solid oxide fuel cells (SOFCs), it demonstrates high ORR activity and excellent CO 2 tolerance under realistic operating conditions. Ni-YSZ-based anode-supported cells with PBSLC 25 C cathodes demonstrate excellent peak power densities of 1.14 W cm -2 , 1.04 W cm -2 , and 0.77 W cm -2 in the air with 1%, 5%, and 10% CO 2 , respectively, at 750 °C. The engineered high-entropy PBSLC 25 C effectively diminishes the CO 2 poisoning effect and maintains active surfaces for fast oxygen exchange, as confirmed by the cell durability test in air containing CO 2 (5 and 10 vol%), Raman spectroscopy, and density functional theory calculations.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Sr 2 MnO 4 as a reactive CO 2 sorbent for sorption-enhanced steam reforming of biogas to green hydrogen

Sorption-enhanced steam biogas reforming is an attractive approach for hydrogen production from renewable resources, with the performance of the CO 2 sorbents being a critical factor. In this study, Sr 2 MnO 4 was investigated as a redox-activated CO 2 sorbent for sustainable hydrogen production from biogas. The Sr 2 MnO 4 sorbents exhibited a CO 2 sorption capacity of over 26 g per 100 g of sorbents, along with excellent cyclic stability in thermogravimetric analysis. Complete regeneration of the sorbent was achieved with a relatively small temperature swing (100 °C). Fixed-bed reactor experiments further demonstrated the application of Sr 2 MnO 4 sorbents in sorption-enhanced steam biogas reforming. Biogas simulants with varying CO 2 contents were converted to ~94 vol% H 2 before CO 2 breakthrough. Stable CO 2 capacity and hydrogen production were maintained over 20 cycles. In addition, optimization of the regeneration duration enabled the generation of highly pure CO 2 and more efficient use of O 2 . These results support the feasibility of biogas-to‑hydrogen conversion with net-negative carbon emissions through integration with CO 2 capture and sequestration.

09 BIOMASS FUELS↗
DOE OSTI2025

Surviving nanoscale interfacial stability in extreme thermal expansion contrast Zn(CN) 2 -epoxy resin matrix composites

Here, we report the remarkable stability at the nanoscale matrix-filler interface in a series of overall low coefficient of thermal expansion (CTE) zinc cyanide (ZC)/epoxy resin composites. These interfaces demonstrate the stability of highly contrasting materials. These composites are designed to optimize the properties of both materials: epoxy resins are valued for their high strength, superb chemical resistance, low dielectric properties, and adhesive abilities. ZC, a model flexible framework, exhibits negative thermal expansion (NTE) behavior and compensates for the epoxy resin’s detrimentally large thermal expansion values. Filled resins minimize the native 65 ppm/°C CTE values to 19 ppm/° C over a wide temperature range while maintaining linearity, yielding composites compatible with typical metal and ceramic substrates’—commonly bonded to the resin— 0–20 ppm/° C CTE values. Additionally, with significant intrinsic differences in the materials, we use wide-angle X-ray diffraction and atomic force microscopy to elucidate thermal movement. The ZC/epoxy interface is surprisingly resilient over 1,000 cycles between -55° C and 75° C, extremes typical to aerospace applications. Further, we show that the resin viscosity remains less than 21 Pa*s at up to 30 vol% ZC, an important consideration for workability. We also discuss settling distribution, glass transition temperature, flexural strength, and longevity. All results point favorably towards practical implementation in low thermal expansion application needs: filling the gap in component design.

42 ENGINEERING↗
DOE OSTI2025

Hydrogen-rich syngas production from the steam co-gasification of low-density polyethylene and coal refuse

Gasification provides a promising pathway for transforming waste materials into valuable products, such as fuels and chemicals. Here, this study investigates the steam co-gasification of low-density polyethylene (LDPE) and compressed thickener underflow, representative of coal refuse (CR), in a drop tube reactor. The effects of feed blend ratio (0–100 wt% LDPE) and temperature (800–1000 °C) on syngas composition, tar formation, and process efficiency are examined. The high volatility of LDPE makes it more reactive than CR but also promotes the formation of 2–7 ring aromatic tars. Increasing temperature improves carbon conversion efficiency (CCE), cold gas efficiency (CGE), and syngas yield, although the lower heating value (LHV) of syngas decreases. Hydrogen is the dominant gas product, reaching 59 vol% with the H 2 /CO molar ratio ranging from 2.27 to 4.74. Synergistic effects from alkali and alkali earth metals (AAEMs), particularly K and Ca, in CR ash enhance syngas yield by catalyzing char gasification and tar cracking. Hematite (Fe 2 O 3 ) and ash from sub-bituminous/bituminous coals are explored as tar reforming catalysts. Fe 2 O 3 achieves 100 % tar reforming efficiency, while coal ash, with a lower Fe 2 O 3 content (15 wt%), is less effective at cracking polycyclic aromatic hydrocarbons, particularly naphthalene. These findings demonstrate the flexibility of co-gasification, allowing precise tuning of syngas characteristics for specific downstream applications. Further optimization of waste-derived catalysts could enhance the economic viability of gasification in waste-to-energy processes.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Innovative duo-recombination layer design for effective hydrogen crossover mitigation in advanced MEAs for PEM water electrolyzers

Hydrogen crossover in proton exchange membrane water electrolyzers (PEMWEs) poses a safety hazard, reduces the overall efficiency, and limits the operational differential pressure range. Here, in this study, a membrane electrode assembly (MEA) with innovative Pt duo-recombination layer (DRL) design is developed by the unique reactive spray deposition technology (RSDT). The novel design comprises two thin RLs integrated within the volume of the membrane and has a total Pt loading of only 0.04 mg Pt cm −2 . Long-term durability test for over 3000 h is performed with as-fabricated MEA at steady-state conditions typical for an industrial hydrogen production system. The results from the durability test show that the newly developed DRL design effectively suppresses the H2 crossover to below 0.5 vol%. Furthermore, comprehensive post-test characterization of the MEA is performed and potential failure mechanisms in the Pt RLs observed during the durability test are identified and discussed in detail for the first time.

08 HYDROGEN↗
DOE OSTI2026

Assessment of binary eutectic Ni alloys for high-temperature applications via laser remelting

It has been recently demonstrated that eutectic alloys processed by additive manufacturing have excellent high-temperature mechanical properties. We suggest that nickel-base eutectic alloys may enable new combinations of structural and functional properties. To this end, we investigate the processability, microstructure, and thermal stability of five, binary near-eutectic Ni-X (X = B, Ce, La, Y, and Zr) alloys processed via surface laser-remelting. The microstructure of all alloys contain a two-phase lamellar eutectic microstructure consisting of γ-Ni and intermetallic phases; this microstructure is significantly finer (100–200 nm lamellar spacing) in the laser-remelted alloys than in the cast substrate (0.5–1.0 µm lamellar spacing). The microhardness of the laser-remelted alloys (550–770 HV) is 35–50% higher than that of the cast alloys (370–570 HV) due to this finer eutectic spacing. An anomalous eutectic microstructure appears at the meltpool boundaries, containing globular and lamellar γ-Ni phases. The alloys contain a high volume fraction (>50 vol%) of intermetallic phase which forms a continuous network, causing brittleness. Following laser-remelting trials, the alloys showed a high density of solid-state cracks, except for the Ni-Zr alloy which processed well. During thermal exposure at 700 and 900°C for up to 500 h, the eutectic microstructure coarsens. Coarsening occurs heterogeneously and initiates at the meltpool boundaries. This process occurs more slowly in the Ni-Zr and Ni-Y alloys, and more rapidly in the remaining alloys, resulting in greater microhardness retention in the Ni-Zr and Ni-Y alloys following thermal exposure at 700°C. Thus, among the five alloys, the Ni-Zr system exhibits a good combination of high-temperature mechanical properties and processability. Here, we conclude with recommendations for future work on designing additively manufactured alloys based on these eutectic Ni systems.

Additive manufacturing↗
DOE OSTI2026

Aluminum bonded SmCo5 magnets with enhanced mechanical strength

Despite their versatility and easy manufacturability, polymer-bonded magnets find limited application due to their limited mechanical properties and temperature resistance. In this study, we developed mechanically robust, aluminum-bonded SmCo5 magnets by utilizing a low-temperature, shear-assisted friction consolidation technique. Bonded magnets with varying magnetic phase content were fabricated at processing temperature of 500°C, and their microstructures, magnetic, mechanical, and electrical properties were systematically investigated. The resulting bonded-magnets showed effective consolidation with nanocrystalline microstructures. Magnetic properties were found to be tunable through variations in binder phase content, with coercivity reaching values up to 15.3 kOe (1217.5 kA/m) and maximum magnetic energy product up to 3.6 MGOe (28.7 kJ/m3), which are comparable to other bonded magnets. Electrical resistivities were lower than the polymer-bonded magnets, but comparable to the sintered ones. We observed an average flexural strength of 223 MPa for 60 vol.% SmCo5/Al sample, which is nearly two times higher than the reported values for sintered and bonded Sm-Co magnets. Our research demonstrated an effective approach to fabricate metal-bonded permanent magnets with superior magnetic and mechanical properties potentially applicable for high temperature applications.

Poudel Chhetri, Tej Bahadur↗
DOE OSTI2025

Hot Hydrogen Exposure of U x Zr 1-x C y Nuclear Fuel: The Effect of Additional Carbon

Nuclear thermal propulsion (NTP) using hydrogen as propellant in a solid-state fission reactor to reach temperatures of up to 3000K can achieve significantly higher specific impulse than chemical propulsion. A promising fuel that is again considered for NTP is U x Zr 1-x C y . To reduce the overall mass loss as well as the uranium fuel loss, a range of experiments using additional carbon in hot hydrogen (2600 K, 6 SLPM flow rate) were performed for up to 5-6 h. Both a CH 4 addition (0.1 and 0.2 vol%) in the hydrogen stream and the use of sacrificial graphite pieces upstream of the samples were tested, with sample compositions from 5 at% UC to 30 at% UC. The results showed a strong reduction of mass loss, up to a factor of 3, as well as a reduction of surface uranium losses in the presence of additional carbon in the atmosphere. Even with additional carbon in the atmosphere, material with 30 at% UC was not stable, but material with 20 at% UC was stable for up to 6h. The sample surfaces showed texturing after processing, possibly by grain growth on the surface. This led to a separation into grains with high uranium content close to the (100)-orientation, and with low uranium content in grains close to the (111)-orientation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Influence of microstructure and temperature on impact toughness of H13 steel produced by binder jet additive manufacturing

Binder Jet Additive Manufacturing (BJAM) is a promising manufacturing pathway to produce H13 steel dies and tooling with complex geometries for applications in high pressure aluminum die casting, hot stamping, and injection molding. While fully dense H13 coupons produced using BJAM have been subjected to detailed microstructure characterization, properties which are critical and relevant to the aforementioned applications, such as impact toughness, have not been reported. Here, this work evaluated the influence of microstructural characteristics and test temperature on the impact toughness of H13 produced by BJAM. Coupons were produced from three different powder size distributions (PSDs), with nominal powder size ranges of −22 μm, 10-32 μm, and 15-53 μm. Coupons were printed, sintered, hot isostatically pressed (HIPed), and heat treated by quenching and tempering. After HIPing, the measured porosities of the different PSDs were all less than 0.015 vol%. The −22 μm PSD BJAM material exhibited the best impact toughness of all three PSDs across the entire test temperature range from 25 to 400 °C, and also exhibited an ambient temperature impact toughness of 10.9 J at a hardness of 46 HRC, equivalent to minimum threshold requirements for premium grade H13. However, all three BJAM PSDs exhibited moderately lower impact toughness than premium grade wrought H13 from RT to 400 °C. We attribute this in part due to the very large prior-austenite grain (PAG) sizes near 400 μm and segregation from former liquid channels leading to greater amounts of carbide precipitation on PAG boundaries. Technical pathways for optimizing processing and chemistry of BJAM H13 to further improve impact toughness are discussed.

Binder jet additive manufacturing↗
DOE OSTI2024

Tribological behavior of hybrid Aluminum-TiB 2 metal matrix composites for brake rotor applications

Here, this research investigates the feasibility of hybrid aluminum metal matrix composites (MMC) incorporating TiB 2 particles for brake rotor applications. The composites were produced by incorporating both in-situ, submicron-sized TiB 2 particles and regular micron-sized TiB 2 powders via stir and squeeze casting techniques into A206 aluminum alloy matrix. Systematic adjustments in the fractions of in-situ and ex-situ TiB 2 particles were conducted to evaluate their impact on wear behavior and mechanisms. Combination of both particle types allowed composites with up to 10 vol% of reinforcements. Composites with higher proportions of ex-situ particles demonstrated increased wear resistance compared to those solely composed of in-situ particles, control specimens without TiB 2 , and conventional cast iron counterparts. The lowest wear rate for the hybrid composites sliding against phenolic brake pads was 1.1 × 10 -5 mm 3 /Nm, signifying a 3-fold reduction relative to cast iron sliding against the same pads. Wear analysis elucidated distinctive mechanisms within the hybrid composites, characterized by mild fragmented abrasive wear, adhesive wear, and plastic deformation, accompanied by the formation of an intermixed tribo-oxide layer.

42 ENGINEERING↗
DOE OSTI2024

The influence of the shock-to-reshock time on the Richtmyer–Meshkov instability in reshock

Experiments on the Richtmyer–Meshkov instability (RMI) in a dual driver vertical shock tube (DDVST) are described. An initially planar, stably stratified membraneless interface is formed by flowing air from above and sulfur hexafluoride from below the interface location using the method of Jones & Jacobs ( Phys. Fluids , vol. 9, issue 1997, 1997, pp. 3078–3085). A random three-dimensional, multi-modal initial perturbation is imposed by vertically oscillating the gas column to produce Faraday waves. The DDVST design generates two shock waves, one originating above and one below the interface, with these shocks having independently controllable strengths and interface arrival times. The shock waves have nominal strengths of $M_L=1.17$ and $M_H=1.18$ for the shock wave originating in the light and heavy gas, respectively, with these strengths chosen to result in arrested bulk interface motion following reshock. The influence of the length of the shock-to-reshock time, as well as the order of shock arrival, on the post-reshock RMI is examined. The mixing layer width grows according to $h\propto t^\theta$ , where $\theta _H=0.36\pm 0.018$ (95 %) and $\theta _L=0.38\pm 0.02$ (95 %) for heavy and light shock first experiments, respectively, indicating no strong dependence on the order of shock wave arrival. Volume integrated specific turbulent kinetic energy (TKE) in the mixing layer versus time is found to decay according to $E_{tot}/\bar {\rho }\propto t^p$ with $p_H=-0.823\pm 0.06$ (95 %) and $p_L=-1.061\pm 0.032$ (95 %) for heavy and light shock first experiments, respectively. Notably, the 95 % confidence intervals do not overlap. Analysis on the influence of the shock-to-reshock time on turbulent length scales, transition criteria, spectra and mixing layer anisotropy are also presented.

Ferguson, Kevin (ORCID:0000000166537482)↗
DOE OSTI2025

Small-scale properties from exascale computations of turbulence on a $\mathbf{32\,768^3}$ periodic cube

To study the physics of small-scale properties of homogeneous isotropic turbulence at increasingly high Reynolds numbers, direct numerical simulation results have been obtained for forced isotropic turbulence at Taylor-scale Reynolds number R λ = 2500 on a 32 768 3 three-dimensional periodic domain using a GPU pseudo-spectral code on a 1.1 exaflop GPU supercomputer (Frontier). These simulations employ the multi-resolution independent simulation (MRIS) technique (Yeung & Ravikumar 2020, Phys. Rev. Fluids, vol. 5, 110517) where ensemble averaging is performed over multiple short segments initiated from velocity fields at modest resolution, and subsequently taken to higher resolution in both space and time. Reynolds numbers are increased by reducing the viscosity with the large-scale forcing parameters unchanged. Although MRIS segments at the highest resolution for each Reynolds number last for only a few Kolmogorov time scales, small-scale physics in the dissipation range is well captured – for instance, in the probability density functions and higher moments of the dissipation rate and enstrophy density, which appear to show monotonic trends persisting well beyond the Reynolds number range in prior works in the literature. Attainment of range of length and time scales consistent with classical scaling also reinforces the potential utility of the present high-resolution data for studies of short-time-scale turbulence physics at high Reynolds numbers where full-length simulations spanning many large-eddy time scales are still not accessible. A single snapshot of the 32 768 3 data is publicly available for further analyses via the Johns Hopkins Turbulence Database.

intermittency↗
DOE OSTI2024

Direct, simple and efficient computation of all components of the virtual-casing magnetic field in axisymmetric geometries with Kapur–Rokhlin quadrature

In a recent publication (Toler et al., J. Plasma Phys., vol. 89, issue 2, 2023, p. 905890210), we demonstrated that for axisymmetric geometries, the Kapur–Rokhlin quadrature rule provided an efficient and high-order accurate method for computing the normal component, on the plasma surface, of the magnetic field due to the toroidal current flowing in the plasma, via the virtual-casing principle. The calculation was indirect, as it required the prior computation of the magnetic vector potential from the virtual-casing principle, followed by the computation of its tangential derivative by Fourier differentiation, to obtain the normal component of the magnetic field. Our approach did not provide the other components of the virtual-casing magnetic field. In this letter, we show that a more direct and more general approach is available for the computation of the virtual-casing magnetic field. The Kapur–Rokhlin quadrature rule accurately calculates the principal value integrals in the expression for all the components of the magnetic field on the plasma boundary, and the numerical error converges at a rate nearly as high as the indirect method we presented previously.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Radiative and continuum dampings of reversed shear Alfvén eigenmodes and perturbative analysis limitations for tokamaks

A careful theoretical analysis of the excitation of Alfvén eigenmodes (AEs), such as TAE (toroidicity-induced AE) and RSAE (reversed shear AE), by superalfvenic energetic particles is required for reliable predictions of energetic ion relaxation in present day fusion experiments. This includes the evaluation of different AE damping mechanisms including radiative and continuum dampings which are the focus of this study. A recent comprehensive benchmark of different eigenmode solvers including gyrokinetic, gyrofluid and hybrid magenetohydrodynamics (MHD) has shown that employed models may have deficiencies when addressing some of them (Taimourzadeh et al., Nucl. Fusion, vol. 59, 2019, 066006). Here, in this paper, we are studying the radiative and continuum dampings of RSAEs in details which were missing in hybrid NOVA/NOVA-C calculations to prepare a NOVA-C package with a substantial upgrade. Both dampings require the finite Larmor radius (FLR) corrections to AE mode structures to be accounted for. Accurately calculating different damping rates and understanding their parametric dependencies, we resolve the limitation coming out of the perturbative approach. In particular, here, the radiative damping is included perturbatively, whereas the continuum damping is computed non-perturbatively. Our comparison leads to the conclusion that the non-perturbative treatment of the unstable RSAE modes is needed to find the agreement with the gyrokinetic calculations. We expect that the RSAE mode structure modification plays a dominant role in determining the RSAE stability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗