Search NASA⌕ Search

SEARCH · Search NASA

Results for “Virtual circuits”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Brightness measurement of an electron impact gas ion source for proton beam writing applications

We are developing a high brightness nano-aperture electron impact gas ion source, which can create ion beams from a miniature ionization chamber with relatively small virtual source sizes, typically around 100 nm. A prototype source of this kind was designed and successively micro-fabricated using integrated circuit technology. Experiments to measure source brightness were performed inside a field emission scanning electron microscope. The total output current was measured to be between 200 and 300 pA. The highest estimated reduced brightness was found to be comparable to the injecting focused electron beam reduced brightness. This translates into an ion reduced brightness that is significantly better than that of conventional radio frequency ion sources, currently used in single-ended MeV accelerators.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

InGaP solar cell on Ge-on-Si virtual substrate for novel solar power conversion

InGaP single-junction solar cells are grown on lattice-matched Ge-on-Si virtual substrates using metal-organic chemical vapor deposition. Optoelectronic simulation results indicate that the optimal collection length for InGaP single-junction solar cells with a carrier lifetime range of 2–5 ns is wider than approximately 1 μ m. Electron beam-induced current measurements reveal that the threading dislocation density (TDD) of InGaP solar cells fabricated on Ge and Ge-on-Si substrates is in the range of 10 4 –3 × 10 7 cm -2 . We demonstrate that the open circuit voltage ( V oc ) of InGaP solar cells is not significantly influenced by TDDs less than 2 × 10 6 cm -2 . Fabricated InGaP solar cells grown on a Ge-on-Si virtual substrate and a Ge substrate exhibit V oc in the range of 0.96 to 1.43 V under an equivalent illumination in the range of ~0.5 Sun. Finally, the estimated efficiency of the InGaP solar cell fabricated on the Ge-on-Si virtual substrate (Ge substrate) at room temperature for the limited incident spectrum spanning the photon energy range of 1.9–2.4 eV varies from 16.6% to 34.3%.

14 SOLAR ENERGY↗

Binary phase digital reflection holograms - Fabrication and potential applications

A novel technique for the fabrication of binary-phase computer-generated reflection holograms is described. By use of integrated circuit technology, the holographic pattern is etched into a silicon wafer and then aluminum coated to make a reflection hologram. Because these holograms reflect virtually all the incident radiation, they may find application in machining with high-power lasers. A number of possible modifications of the hologram fabrication procedure are discussed.

Gallagher, N. C., Jr.↗

Equivalent-Circuit Models for Grid-Forming Inverters under Unbalanced Steady-State Operating Conditions: Preprint

Positive- and negative-sequence equivalent-circuit models are put forth to capture the operation of grid-forming (GFM) inverters in unbalanced steady-state operating conditions acknowledging the impact of current limiting. The particular control architecture examined adopts droop control (for primary control), nested inner-current and outer-voltage control (in the stationary reference frame), and it is adaptable to two different types of current limiting (current-reference saturation and virtual-impedance limiting). We anticipate the proposed models to be of interest in modeling, analysis, and simulation of GFM inverters in unbalanced settings that may arise, e.g., in the face of faults. Validation of the equivalent-circuit models is pursued via comparison with full-order electromagnetic-transient (EMT) simulations for representative balanced and unbalanced faults.

equivalent-circuit models↗

Validating quantum-classical programming models with tensor network simulations

The exploration of hybrid quantum-classical algorithms and programming models on noisy near-term quantum hardware has begun. As hybrid programs scale towards classical intractability, validation and benchmarking are critical to understanding the utility of the hybrid computational model. In this paper, we demonstrate a newly developed quantum circuit simulator based on tensor network theory that enables intermediate-scale verification and validation of hybrid quantum-classical computing frameworks and programming models. We present our tensor-network quantum virtual machine (TNQVM) simulator which stores a multi-qubit wavefunction in a compressed (factorized) form as a matrix product state, thus enabling single-node simulations of larger qubit registers, as compared to brute-force statevector simulators. Our simulator is designed to be extensible in both the tensor network form and the classical hardware used to run the simulation (multicore, GPU, distributed). The extensibility of the TNQVM simulator with respect to the simulation hardware type is achieved via a pluggable interface for different numerical backends (e.g., ITensor and ExaTENSOR numerical libraries). We demonstrate the utility of our TNQVM quantum circuit simulator through the verification of randomized quantum circuits and the variational quantum eigensolver algorithm, both expressed within the eXtreme-scale ACCelerator (XACC) programming model.

97 MATHEMATICS AND COMPUTING↗

A collaborative network middleware project by Lambda Station, TeraPaths, and Phoebus

The TeraPaths, Lambda Station, and Phoebus projects, funded by the US Department of Energy, have successfully developed network middleware services that establish on-demand and manage true end-to-end, Quality-of-Service (QoS) aware, virtual network paths across multiple administrative network domains, select network paths and gracefully reroute traffic over these dynamic paths, and streamline traffic between packet and circuit networks using transparent gateways. These services improve network QoS and performance for applications, playing a critical role in the effective use of emerging dynamic circuit network services. They provide interfaces to applications, such as dCache SRM, translate network service requests into network device configurations, and coordinate with each other to setup up end-to-end network paths. The End Site Control Plane Subsystem (ESCPS) builds upon the success of the three projects by combining their individual capabilities into the next generation of network middleware. ESCPS addresses challenges such as cross-domain control plane signalling and interoperability, authentication and authorization in a Grid environment, topology discovery, and dynamic status tracking. The new network middleware will take full advantage of the perfSONAR monitoring infrastructure and the Inter-Domain Control plane efforts and will be deployed and fully vetted in the Large Hadron Collider data movement environment.

99 GENERAL AND MISCELLANEOUS↗

Hardware accuracy counters for application precision and quality feedback

Methods, devices, and systems for capturing an accuracy of an instruction executing on a processor. An instruction may be executed on the processor, and the accuracy of the instruction may be captured using a hardware counter circuit. The accuracy of the instruction may be captured by analyzing bits of at least one value of the instruction to determine a minimum or maximum precision datatype for representing the field, and determining whether to adjust a value of the hardware counter circuit accordingly. The representation may be output to a debugger or logfile for use by a developer, or may be output to a runtime or virtual machine to automatically adjust instruction precision or gating of portions of the processor datapath.

47 OTHER INSTRUMENTATION↗

Density Matrix Quantum Circuit Simulation via the BSP Machine on Modern GPU Clusters

As quantum computers evolve, simulations of quantum programs on classical computers will be essential in validating quantum algorithms, understanding the effect of system noise, and design applications for future quantum computers. In this paper, we propose a novel multi-GPU programming model called MG-BSP that constructs a virtual BSP machine on top of modern multi-GPU platforms, and tweak the programming model to build a multi-GPU density matrix quantum simulator. We propose and evaluated a new formulation minimizing communication and prove that the transformation conserves original semantics when noise is introduced. We build the tool-chain to support quantum assembly open standard, synthesize testing quantum circuit, and enable ultra-deep quantum simulation. We evaluated our design on four state-of-the-art multi-GPU platforms including the latest DGX-1 and DGX-2 systems. We demonstrate simulation of 1 million gates in 94 minutes, far deeper circuits than has been demonstrated in prior work. A roofline-model analysis show that we have reached near-optimal performance under memory bound.

Li, Ang↗

Multiphase Resistivity Model for Magnetic Nanocomposites Developed for High Frequency, High Power Transformation

New power conversion systems that offer promise to transform electricity grids into unified interactive supply networks require high-resistivity soft-magnetic materials to allow for switching of magnetic materials at frequencies approaching 100 kHz for power transformation in the megawatt range. Amorphous and nanocomposite soft-magnetic materials, which represent the state of the art in terms of high power densities and low losses at high frequencies, have resistivities that depend on the structures and spatial distributions of multiple phases in thin ribbons. We present a multiphase resistivity model applicable to nanocomposite materials by considering an equivalent circuit approach considering paths through an amorphous, crystalline, and growth inhibitor shell phase. We detail: (a) identification of amorphous, crystalline, and shell phases; (b) consideration of the role of the morphology of each phase in an equivalent circuit model for the resistance; (c) a two-band model for the Fe/Co composition dependence of the resistivity in crystalline and amorphous phases; (d) a virtual bound state model for resistivity to explain increased resistivity due to early transition-metal growth inhibitors in the shell surrounding the nanocrystalline phase; and (e) disorder effects on amorphous phase resistivity. Experimental design and results for systems of interest in high-frequency power transformation are discussed in the context of our model including: (a) techniques for measurements of cross-section and density, (b) four-point probe and surface resistivity measurements, and (c) measurements in Fe- and Co-rich systems comparing amorphous and nanocomposite materials.

DeGeorge, V↗

All-digital QPSK modulator

Circuit consisting to only four components (2 IC chips and 2 time delay devices) modulates RF signal with 2 asynchronous digital data signals. Digital modulator is virtually free of amplitude modulation, is not subject to temperature effects from other components, dissipates less power, and is far simpler than its analog predecessors.

Burgess, R. W.↗

An Algorithm of an X-ray Hit Allocation to a Single Pixel in a Cluster and Its Test-Circuit Implementation

An on-chip implementable algorithm for allocation of an X-ray photon imprint, called a hit, to a single pixel in the presence of charge sharing in a highly segmented pixel detector is described. Its proof-of-principle implementation is also given supported by the results of tests using a highly collimated X-ray photon beam from a synchrotron source. The algorithm handles asynchronous arrivals of X-ray photons. Activation of groups of pixels, comparisons of peak amplitudes of pulses within an active neighborhood and finally latching of the results of these comparisons constitute the three procedural steps of the algorithm. A grouping of pixels to one virtual pixel, that recovers composite signals and event driven strobes, to control comparisons of fractional signals between neighboring pixels are the actuators of the algorithm. The circuitry necessary to implement the algorithm requires an extensive inter-pixel connection grid of analog and digital signals, that are exchanged between pixels. A test-circuit implementation of the algorithm was achieved with a small array of 32 × 32 pixels and the device was exposed to an 8 keV highly collimated to a diameter of 3-μm X-ray beam. Furthermore, the results of these tests are given in this paper assessing physical implementation of the algorithm.

47 OTHER INSTRUMENTATION↗

Final Report for CCS Cross-Layer Reliability Visioning Study

The geometric rate of improvement of transistor size and integrated circuit performance known as Moore's Law has been an engine of growth for our economy, enabling new products and services, creating new value and wealth, increasing safety, and removing menial tasks from our daily lives. Affordable, highly integrated components have enabled both life-saving technologies and rich entertainment applications. Anti-lock brakes, insulin monitors, and GPS-enabled emergency response systems save lives. Cell phones, internet appliances, virtual worlds, realistic video games, and mp3 players enrich our lives and connect us together. Over the past 40 years of silicon scaling, the increasing capabilities of inexpensive computation have transformed our society through automation and ubiquitous communications. Looking forward, increasing unpredictability threatens our ability to continue scaling integrated circuits at Moore's Law rates. As the transistors and wires that make up integrated circuits become smaller, they display both greater differences in behavior among devices designed to be identical and greater vulnerability to transient and permanent faults. Conventional design techniques expend energy to tolerate this unpredictability by adding safety margins to a circuit's operating voltage, clock frequency or charge stored per bit. However, the rising energy costs needed to compensate for increasing unpredictability are rapidly becoming unacceptable in today's environment where power consumption is often the limiting factor on integrated circuit performance and energy efficiency is a national concern. Reliability and energy consumption are both reaching key inflection points that, together, threaten to reduce or end the benefits of feature size reduction. To continue beneficial scaling, we must use a cross-layer, Jull-system-design approach to reliability. Unlike current systems, which charge every device a substantial energy tax in order to guarantee correct operation in spite of rare events, such as one high-threshold transistor in a billion or one erroneous gate evaluation in an hour of computation, cross-layer reliability schemes make reliability management a cooperative effort across the system stack, sharing information across layers so that they only expend energy on reliability when an error actually occurs. Figure 1 illustrates an example of such a system that uses a combination of information from the application and cheap architecture-level techniques to detect errors. When an error occurs, mechanisms at higher levels in the stack correct the error, efficiently delivering correct operation to the user in spite of errors at the device or circuit levels. In the realms of memory and communication, engineers have a long history of success in tolerating unpredictable effects such as fabrication variability, transient upsets, and lifetime wear using information sharing, limited redundancy, and cross-layer approaches that anticipate, accommodate, and suppress errors. Networks use a combination of hardware and software to guarantee end-toend correctness. Error-detection and correction codes use additional information to correct the most common errors, single-bit transmission errors. When errors occur that cannot be corrected by these codes, the network protocol requests re-transmission of one or more packets until the correct data is received. Similarly, computer memory systems exploit a cross-layer division of labor to achieve high performance with modest hardware. Rather than demanding that hardware alone provide the virtual memory abstraction, software page-fault and TLB-miss handlers allow a modest piece of hardware, the TLB, to handle the common-case operations on a cyc1e-by-cycle basis while infrequent misses are handled in system software. Unfortunately, mitigating logic errors is not as simple or as well researched as memory or communication systems. This lack of understanding has led to very expensive solutions. For example, triple-modular redundancy masks errors by triplicating computations in either time or area. This mitigation methods imposes a 200% increase in energy consumption for every operation, not just the uncommon failure cases. At a time when computation is rapidly becoming part of our critical civilian and military infrastructure and decreasing costsfor computation are fueling our economy and our well being, we cannot afford increasingly unreliable electronics or a stagnation in capabilities per dollar, watt, or cubic meter. If researchers are able to develop techniques that tolerate the growing unpredictability of silicon devices, Moore's Law scaling should continue until at least 2022. During this 12-year time period, transistors, which are the building blocks of electronic devices, will scale their dimensions (feature sizes) from 45nm to 4.5nm.

99 GENERAL AND MISCELLANEOUS↗

Recent developments in semiconductor research

Recent findings drawn from various laboratories focused toward a new understanding of the nature of crystal growth and how impurities are incorporated or excluded from the lattice were considered. From these findings a heuristic approach is given for improving the uniformity and charge carrier concentration of thin semiconductor films. Such improvement is considered essential to achieve respectable yield on large scale integrated circuits. A tentative conclusion is drawn which indicates that if the host compound crystal reactants are provided to the growing crystal surface in a reasonably stoichiometric manner, it is virtually impossible to include impurities into a growing crystal surface held at a sufficiently low temperature; impurities are incorporated into the crystal by gettering action of crystal defects located one and two monlayers beneath the growing surface. Devices in 3-5 semiconductors based on heterojunctions and two dimensional electron gases are noted and reliability concerns are voiced. Alternatives and novel device structures such as truly single crystal high quality silicon on insulator and beta silicon carbide devices are presented.

Yoder, M. N.↗

Adaptation of virtual synchronous generators to dynamic conditions in power grids

Virtual synchronous generators (VSGs) are widely adopted as grid-forming controls for inverter-based resources. However, when grid conditions vary significantly as characterized by changes in short-circuit ratio (SCR) and the reactance-to-resistance (X/R) ratio, fixed-gain designs and the commonly used P–Q decoupling assumption can become inaccurate. Such conditions can degrade transient power performance, leading to oscillations, prolonged settling, and overshoot, particularly in stiff-grid operating points. This paper quantifies how grid strength and impedance-dependent coupling affect the active–reactive power dynamics of a conventional VSG over a broad range of SCR and X/R values. An adaptive VSG tuning framework is then developed by combining (i) a coupling-explicit, impedance-parameterized state-space model to enable systematic controller synthesis, (ii) a full-state-feedback law designed via pole placement to meet prescribed damping and settling-time specifications, and (iii) a physics-informed neural network (PINN)–based online grid-impedance estimator that updates controller gains in real time as grid conditions vary. Offline simulations in MATLAB/Simulink and real-time validation on an OPAL-RT platform show that the proposed method preserves consistent damping and settling behavior with reduced overshoot across wide SCR and X/R ranges, compared with fixed-gain VSG baselines.

Adaptive control↗

Flame Detector

Scientific Instruments, Inc. has now developed a second generation, commercially available instrument to detect flames in hazardous environments, typically refineries, chemical plants and offshore drilling platforms. The Model 74000 detector incorporates a sensing circuit that detects UV radiation in a 100 degree conical field of view extending as far as 250 feet from the instrument. It operates in a bandwidth that makes it virtually 'blind' to solar radiation while affording extremely high sensitivity to ultraviolet flame detection. A 'windowing' technique accurately discriminates between background UV radiation and ultraviolet emitted from an actual flame, hence the user is assured of no false alarms. Model 7410CP is a combination controller and annunciator panel designed to monitor and control as many as 24 flame detectors. *Model 74000 is no longer being manufactured.

Source record↗

SU-E-E-08: Applications of the Quantization of Coupled Circuits in Radiation Physics (design of Klystron, Bremsstrahlung, Synchrotron)

Purpose: During the past decade the quantization of coupled/forced electromagnetic circuits with or without Ohm’s resistance has gained the subject of some fundamental studies, since even problems of quantum electrodynamics can be solved in an elegant manner, e.g. the creation of quantized electromagnetic fields. In this communication, we shall use these principles to describe optimization procedures in the design of klystrons, synchrotron irradiation and high energy bremsstrahlung. Methods: The base is the Hamiltonian of an electromagnetic circuit and the extension to coupled circuits, which allow the study of symmetries and perturbed symmetries in a very apparent way (SU2, SU3, SU4). The introduction resistance and forced oscillators for the emission and absorption in such coupled systems provides characteristic resonance conditions, and atomic orbitals can be described by that. The extension to virtual orbitals leads to creation of bremsstrahlung, if the incident electron (velocity v nearly c) is described by a current, which is associated with its inductivitance and the virtual orbital to the charge distribution (capacitance). Coupled systems with forced oscillators can be used to amplify drastically the resonance frequencies to describe klystrons and synchrotron radiation. Results: The cross-section formula for bremsstrahlung given by the propagator method of Feynman can readily be derived. The design of klystrons and synchrotrons inclusive the radiation outcome can be described and optimized by the determination of the mutual magnetic couplings between the oscillators induced by the currents. Conclusions: The presented methods of quantization of circuits inclusive resistance provide rather a straightforward way to understand complex technical processes such as creation of bremsstrahlung or creation of radiation by klystrons and synchrotrons. They can either be used for optimization procedures and, last but not least, for pedagogical purposes with regard to a qualified understanding of radiation physics for students.

43 PARTICLE ACCELERATORS↗

Release on the Virtual Test Bed of a Molten Salt Reactor Experiment SAM-Pronghorn Coupled Model using the Domain Overlapping Approach

The nuclear industry is taking leaps in innovations with companies seeking a sustainable energy future through advanced nuclear reactors. The Department of Energy (DOE)’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program seeks to substantiate and bolster the deployment of advanced reactors through flexible multifidelity, multiphysics simulations of advanced nuclear reactors. Applications like SAM for one-dimensional systems thermalhydraulics, and Pronghorn for multidimensional coarse mesh thermal-hydraulics, are geared to support innovations in industry by facilitating design, optimization, and licensing of advanced nuclear reactors. Coupling systems thermal-hydraulics and computational fluid dynamics codes can be difficult as the pressure coupling converges slowly; however, it is important to obtain the desired accuracy in each part of the primary loop. The authors of this model created an Overlapping-Domain Coupling (ODC) approach to coupling SAM and Pronghorn. Leveraging this coupling technique, a Molten Salt Reactor Experiment (MSRE) model was developed and released to the NEAMS/National Reactor Innovation Center (NRIC) Virtual Test Bed (VTB). The MSRE was chosen to be modeled because of the wealth of experimental data available and because of the strong physics coupling between the core and primary circuit. This paper contextualizes the history of the MSRE, describes the thermal hydraulics models used, and detail the implementation of multidimensional thermal-hydraulics and system codes based on the ODC method for the MSRE model. Finally, this paper presents how other modelers could apply the SAM Pronghorn ODC for other advanced reactor models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A Solution in Search of Problems

Ferrofluids offered vast-problem solving potential. Under license for the NASA technology, Dr. Ronald Moskowitz and Dr. Ronald Rosensweig formed Ferrofluids Corporation. First problem they found a solution for was related to the manufacture of semiconductor "chips" for use in electronic systems. They developed a magnetic seal composed of ferrofluid and a magnetic circuit. Magnetic field confines the ferrofluid in the regions between the stationary elements and the rotary shaft of the seal. Result is a series of liquid barriers that totally bar passage of contaminants. Seal is virtually wear-proof and has a lifetime measured in billions of shaft revolutions. It has reduced maintenance, minimizes "downtime" of production equipment, and reduces the cost of expensive materials that had previously been lost through seal failures. Products based on ferrofluid are exclusion seals for computer disc drives and inertia dampers for stepper motors. Uses are performance-improving, failure-reducing coolants for hi-fi loudspeakers. Other applications include analytical instrumentation, medical equipment, industrial processes, silicon crystal growing furnaces, plasma processes, fusion research, visual displays, and automated machine tools.

Source record↗