SEARCH · Search NASA

Results for “compressibility factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Three-dimensional instability of rotating flows with oscillating axial strain

The equations of motion for perturbed uniformly rotating flows with uniform axial-time periodic strain, are derived from the Navier-Stokes equations in the low Mach number limit. The perturbation equations admit exponentially growing three-dimensional solutions for which the amplification factors per period are computed for a range of compression and swirl ratios. It is found that for a given compression ratio, the flow is stable for swirl ratios, but at high swirl ratios the flow is unstable with the amplification factor dependent on wave angle but independent of wavelength. For an unstable swirl ratio, higher compression ratios yield larger amplification factors.

Mansour, Nagi N.↗

NASA NTRS1966

Compression springs at elevated temperatures

The behavior of compression springs is affected by increased temperatures. The most significant factors affecting springs are a loss of load and length (relaxation), and a change in the modulus of rigidity. Relaxation will reduce preset loads or change the location of supported components whereas a change in the modulus of rigidity will alter the spring rate. Both factors must be taken into account when designing compression springs. Curves and equations are presented (for music wire, 18-8 stainless steel, 17-7 PH, and Inconel-X) which can aid in the design of compression springs for use at elevated temperatures.

Spring↗

NASA NTRS1994

Planning/scheduling techniques for VQ-based image compression

The enormous size of the data holding and the complexity of the information system resulting from the EOS system pose several challenges to computer scientists, one of which is data archival and dissemination. More than ninety percent of the data holdings of NASA is in the form of images which will be accessed by users across the computer networks. Accessing the image data in its full resolution creates data traffic problems. Image browsing using a lossy compression reduces this data traffic, as well as storage by factor of 30-40. Of the several image compression techniques, VQ is most appropriate for this application since the decompression of the VQ compressed images is a table lookup process which makes minimal additional demands on the user's computational resources. Lossy compression of image data needs expert level knowledge in general and is not straightforward to use. This is especially true in the case of VQ. It involves the selection of appropriate codebooks for a given data set and vector dimensions for each compression ratio, etc. A planning and scheduling system is described for using the VQ compression technique in the data access and ingest of raw satellite data.

Short, Nicholas M., Jr.↗

NASA NTRSDate not supplied

Equivalent Mass Benefits from Employing Vapor Compression Refrigeration on Spacecraft

Thermoelectric cooling, reversed Brayton cycles and Stirling cycle devices are common cooling technologies employed on spacecraft where temperatures below the radiator temperature are needed. Although used less often in microgravity, vapor compression refrigeration was proposed for microgravity applications as early as the 1970s. Researchers proposed the vapor compression cycle over other cooling technologies for its superior energy efficiency in the typical refrigerator/freezer and air-conditioning temperature range. The higher energy efficiency should alleviate the mass penalty of the thermal system, conceivably both for satellites and manned spacecraft. Despite numerous propositions, the literature lacks a discussion of the absolute equivalent mass benefit achievable and the value of it relative to the total mass of the thermal system of the spacecraft or the spacecraft itself. This paper presents the equivalent mass benefits of employing a vapor compression system over other cooling technologies using a mass penalty factor for power consumption. Additionally, a prototype vapor compression cooler sized to fit into an ISS locker is presented.

refrigerator↗

NASA NTRS1962

BUCKLING OF INITIALLY IMPERFECT AXIALLY COMPRESSED CYLINDRICAL SHELLS

The effects of imperfections on the buckling strength of pressurized cylinders under axial compression are studied. The imperfection factor is considered in the finite-deflection compatibility equation, as well as in the equilibrium equation. A new relation to express the imperfection as an explicit exponential function of pressure and radius thickness ratio is proposed. A method for finding the exponential function is described, and the solution for the critical stress is found in a fairly simple form. The relation of decrease of stability with respect to magnitude of imperfections if found.

CYLINDRICAL SHELL↗

NASA NTRS1991

SAR data compression: Application, requirements, and designs

The feasibility of reducing data volume and data rate is evaluated for the Earth Observing System (EOS) Synthetic Aperture Radar (SAR). All elements of data stream from the sensor downlink data stream to electronic delivery of browse data products are explored. The factors influencing design of a data compression system are analyzed, including the signal data characteristics, the image quality requirements, and the throughput requirements. The conclusion is that little or no reduction can be achieved in the raw signal data using traditional data compression techniques (e.g., vector quantization, adaptive discrete cosine transform) due to the induced phase errors in the output image. However, after image formation, a number of techniques are effective for data compression.

Curlander, John C.↗

NASA NTRSDate not supplied

High Performance Access to Archival Data Stored in HDF4 and HDF5 on Cloud Object Stores Without Reformatting the Files

Cloud computing offers numerous advantages for users of extensive Earth science data collections. These benefits encompass direct online access to data files and granules from any location, scalable access supporting parallel computing workflows, and flexible computing tools enabling innovative experimentation with processing techniques. However, older archival file formats designed for distinct computing systems hinder efficient access to decade-long time-series data when compared to data stored in modern cloud-optimized formats like Web Object Stores (WOS), exemplified by Amazon Web Services’ Simple Storage Service (S3). We describe DMR++ (Dataset Metadata Response plus plus), a technology facilitating efficient access to HDF5 (Hierarchical Data Format, version 5) and HDF4 files stored on WOS systems without requiring data reformatting. DMR++ achieves performance comparable to technologies like Zarr while preserving the original file structure, a substantial benefit considering the vast quantity of archival files held by organizations such as NASA. Moreover, DMR++ typically outperforms cloud-optimized versions of HDF5. Essentially an XML (Extensible Markup Language) document usually stored alongside the described data, DMR++ can also be generated on-the-fly but is generally created during data staging to the WOS. Archival files that use HDF4/5 often store large arrays of numerical data. The data in these files is often compressed, typically reducing their size by a factor of four or more. To achieve efficient access to portions of those arrays, they are 'chunked' into smaller sub-arrays, each individually compressed. The chunk size is a compromise, where spinning disks can efficiently access data in smaller chunks while S3 favors larger chunks. A simple optimization of aggregating smaller chunks that are stored adjacently, transferring them in a single access and then individually decompressing them will improve performance. NASA data pose an additional challenge: special Application Programmer Interface (API) libraries are often needed to compute some variables. These libraries are incompatible with WOS environments. Our solution involves storing computed values in the DMR++ document or a companion file, making them accessible like other variables and eliminating the need for specialized APIs. We outline specific optimizations for both satellite grid and swath data stored in HDF4-EOS2 (Earth Observing System).

James Gallagher↗

NASA NTRS1919

Effect of Compression Ratio, Pressure, Temperature, and Humidity on Power

Among other factors which affect the horsepower of an airplane engine are the atmospheric pressure, and consequently the altitude at which the engine is working, and the compression ratio, or cylinder volume divided by clearance volume. The tests upon which this report is based were selected from a large number of runs made during the intercomparison of various gasolines to determine the variation of horsepower with altitude at three different compression ratios. The test results and conclusions are presented in this report.

Dickinson, H C↗

NASA NTRS1989

An improved algorithm for the modeling of vapor flow in heat pipes

A heat pipe vapor flow algorithm suitable for use in codes on microcomputers is presented. The incompressible heat pipe vapor flow studies of Busse are extended to incorporate compressibility effects. The Busse velocity profile factor is treated as a function of temperature and pressure. The assumption of a uniform saturated vapor temperature determined by the local pressure at each cross section of the pipe is not made. Instead, a mean vapor temperature, defined by an energy integral, is determined in the course of the solution in addition to the pressure, saturation temperature at the wall, and the Busse velocity profile factor. For alkali metal working fluids, local species equilibrium is assumed. Temperature and pressure profiles are presented for several cases involving sodium heat pipes. An example for a heat pipe with an adiabatic section and two evaporators in sequence illustrates the ability to handle axially varying heat input. A sonic limit plot for a short evaporator falls between curves for the Busse and Levy inviscid sonic limits.

Tower, Leonard K.↗

NASA NTRS2024

Direct Ink Write 3D Printing of Fully Dense and Functionally Graded Liquid Metal Elastomer Foams

Liquid metal (LM) elastomer composites offer promising potential in soft robotics, wearable electronics, and human-machine interfaces. Direct ink write (DIW) 3D printing offers a versatile manufacturing technique capable of precise control over LM microstructures, yet challenges such as interfilament void formation in multilayer structures impact material performance. Here, a DIW strategy is introduced to control both LM microstructure and material architecture. Investigating three key process parameters–nozzle height, extrusion rate, and nondimensionalized nozzle velocity–it is found that nozzle height and velocity predominantly influence filament geometry. The nozzle height primarily dictates the aspect ratio of the filament and the formation of voids. A threshold print height based on filament geometry is identified; below the height, significant surface roughness occurs, and above the ink fractures, which facilitates the creation of porous structures with tunable stiffness and programmable LM microstructure. These porous architectures exhibit reduced density and enhanced thermal conductivity compared to cast samples. When used as a dielectric in a soft capacitive sensor, they display high sensitivity (gauge factor = 9.0), as permittivity increases with compressive strain. These results demonstrate the capability to simultaneously manipulate LM microstructure and geometric architecture in LM elastomer composites through precise control of print parameters, while maintaining geometric fidelity in the printed design.

Spencer Pak↗

NASA NTRS1972

Transport properties of liquid metal hydrogen under high pressures

A theory is developed for the compressibility and transport properties of liquid metallic hydrogen, near to its melting point and under high pressure. The interionic force law is assumed to be of the screened Coulomb type, because hydrogen has no core electrons. The random phase approximation is used to obtain the structure factor S(k) of the system in terms of the Fourier transform of this force law. The long wavelenth limit of the structure factor S(o) is related to the compressibility, which is much lower than that of alkali metals at their melting points. The diffusion constant at the melting point is obtained in terms of the Debye frequency, using a frequency spectrum analogous with the phonon spectrum of a solid. A similar argument is used to obtain the combined shear and bulk viscosities, but these depend also on S(o). The transport coefficients are found to be about the same size as those of alkali metals at their melting points.

Brown, R. C.↗

NASA NTRS1991

Data compression: The end-to-end information systems perspective for NASA space science missions

The unique characteristics of compressed data have important implications to the design of space science data systems, science applications, and data compression techniques. The sequential nature or data dependence between each of the sample values within a block of compressed data introduces an error multiplication or propagation factor which compounds the effects of communication errors. The data communication characteristics of the onboard data acquisition, storage, and telecommunication channels may influence the size of the compressed blocks and the frequency of included re-initialization points. The organization of the compressed data are continually changing depending on the entropy of the input data. This also results in a variable output rate from the instrument which may require buffering to interface with the spacecraft data system. On the ground, there exist key tradeoff issues associated with the distribution and management of the science data products when data compression techniques are applied in order to alleviate the constraints imposed by ground communication bandwidth and data storage capacity.

Tai, Wallace↗

NASA NTRS1988

Magnetic ULF fluctuations in the compressional zone of AMPTE's artificial comets

The two Ba releases in the solar wind, termed artificial comets (the first in interplanetary space, the second in the terrestrial magnetosheath), showed a number of common magnetic features. Both times a magnetic cavity was detected and a field pile-up observed with magnitudes several times the ambient field strength upstream of the cavity. The magnetic fluctuations in the compressed region are generally enhanced by a factor comparable to the amount of field pile-up. There is a peak in the spectra of both events around 0.1 Hz in the component which is perpendicular to the solar-wind velocity vector and almost field-aligned. This magnetosonic wave has been interpreted as the fundamental mode of resonance oscillations of the compression zone. For frequencies beyond 2 Hz the spectra decrease more steeply in the case of the second 'comet' than in the first. This is due to the interaction of the supersonic solar wind with the first comet. The spectra obtained during the first comet at the solar-wind/ion-cloud interface are identical to those observed during bow-shock crossings.

Kloecker, N.↗

NASA NTRS1993

Dynamics of large scale impacts on Venus and Earth

Large scale impacts are a key aspect of the accretion and growth of the planets, the evolution of their atmospheres, and the viability of their life forms. We have performed an extensive series of numerical calculations that examined the mechanics of impacts over a broad range of conditions and are now extending these to account for the effects of the planetary atmosphere. We have examined the effects of large scale impacts in which the trapping and compression of an atmosphere during impact is a significant factor in the transfer of energy to the atmosphere. The various energy transfer regimes and where conventional drag and trapping and subsequent compression of atmosphere between the bolide and planetary surface are significant are shown.

Okeefe, John D.↗

NASA NTRS1991

An iterative implicit diagonally-dominant factorization algorithm for solving the Navier-Stokes equations

Presented here is an algorithm for solving the multidimensional unsteady Navier-Stokes equations for compressible flows. It is based on a diagonally-dominant approximate factorization procedure. The factorization error and the timewise linearization error associated with this procedure are reduced by performing Newton-type inner iterations at each time step. The inviscid fluxes are evaluated by the fourth-order central differencing scheme amended with a numerical dissipation directly proportional to the entire dissipative part of the truncation error intrinsic to the third order biased upwind scheme. The important features of the proposed solution are elucidated by the numerical results of the convection of a vortex and the backward-facing step flows.

Chen, Shu-Cheng↗

NASA NTRS1977

Calculation of three-dimensional compressible turbulent boundary layers

From comparisons of high speed data with low speed closure procedures using variable mean density, there does not appear to be any appreciable influence of compressibility upon turbulent shear stress modeling in compressible turbulent boundary layers, even for extreme cases such as Mach 14 to 20 with a change in density across the layer of up to a factor of 100. Other evidence of apparent lack of compressibility caused new physics which may alter the shear stress for the compressible boundary layer cases including: (1) fluctuation Mach number was generally less than 1; (2) the shear stress distribution through the boundary layer was not a function of Mach number for zero pressure gradient flows; (3) the Morkovin hypothesis was valid up to Mach 5 (based on fluctuation data); (4) profile N power was not a function of Mach number, at least up to Mach 10; and (5) the nondimensional burst period was approximately the same as that for low speed.

Source record↗

NASA NTRS2004

Science-based Region-of-Interest Image Compression

As the number of currently active space missions increases, so does competition for Deep Space Network (DSN) resources. Even given unbounded DSN time, power and weight constraints onboard the spacecraft limit the maximum possible data transmission rate. These factors highlight a critical need for very effective data compression schemes. Images tend to be the most bandwidth-intensive data, so image compression methods are particularly valuable. In this paper, we describe a method for prioritizing regions in an image based on their scientific value. Using a wavelet compression method that can incorporate priority information, we ensure that the highest priority regions are transmitted with the highest fidelity.

Wagstaff, K. L.↗

NASA NTRS1989

Experimental observations and finite element analysis of the initiation of fiber microbuckling in notched composite laminates

An understanding was developed of the factors that determine the semi-circular edge-notched compressive strength and the associated failure mode(s) were identified of thermoplastic composite laminates with multidirectional stacking sequences. The experimental observations and the detailed literature review suggest at least four factors that affected the determination of the strain levels at which fiber microbuckling initiates and thus, partially control the composite's compression strength. The dependent variables studied are the compressive strength of a reduced gage section compression specimen and the compression strength of a compression specimen with two semi-circular edge notches (no opposite free edges) centered along the gage section. In this research, specimens containing two semi-circular edge notches (no opposite free edges) were loaded in compression at a relatively slow rate to provide more stable development of fiber microbuckling damage. The results indicate that the local constraints (free surfaces, supporting ply orientation, and resin-rich regions) significantly affect the strain level for the initiation of in-plane fiber microbuckling. Preliminary results at an elevated temperature, 77 C, showed the shear stress yield strength of the resin was reduced and consequently, the resistance to fiber microbuckling was also reduced. The finite element analysis of the perfectly straight fiber problem indicates that the free surface effect causes a 10 percent reduction in the critical buckling strain. However, the experimentally measured reduction for fibers with an initial fiber curvature, was 35 percent.

Guynn, E. Gail↗