Search NASA⌕ Search

SEARCH · Search NASA

Results for “fast-response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Buoyancy Effects in Strongly-Pulsed, Turbulent Diffusion Flames

The objective of this experiment is to better understand the combustion behavior of pulsed, turbulent diffusion flames by conducting experiments in microgravity. The fuel jet is fully-modulated (i.e., completely shut off between pulses) by an externally controlled valve system leading to enhanced fuel/air mixing compared to acoustically excited or partially-modulated jets. Experiments are conducted both in laboratories at UW and WPI and in the GRC 2.2s Drop Tower. A single fuel nozzle with diameter d = 2 mm is centered in a combustor 20 20 cm in cross section and 67 cm in height. The gaseous fuel flow (ethylene or a 50/50 ethylene/nitrogen mixture by volume) is fully-modulated by a fast-response solenoid valve with injection times from tau = 4 to tau = 300 ms. The nominal Reynolds number based on the fuel velocity during injection, U(sub jet), is 5,000. A slow oxidizer co-flow properly ventilates the flame and an electrically heated wire loop serves as a continuous ignition source. Diagnostic techniques include video imaging, fine-wire thermocouples and thermopile radiometers, and gas sampling and standard emissions instruments (the last in the laboratory only).

Hermanson, J. C.↗
NASA NTRS1957

Surge-Inception Study in a Two-Spool Turbojet Engine

A two-spool turbojet engine was operated in the Lewis altitude wind tunnel to study the inception of compressor surge. In addition to the usual steady-state pressure and temperature measurements, the compressors were extensively instrumented with fast-response interstage pressure transducers. Thus it was possible to obtain maps for both compressors, pressure oscillations during rotating stall, effects of stall on efficiency, and stage-loading curves. In addition, with the transient measurements, it was possible to record interstage pressures and then compute stage performance during accelerations to the stall limit. Rotating stall was found to exist at low speeds in the outer spool. Although the stall arose from poor flow conditions at the inlet-stage blade tips, the low-energy air moved through the machine from the tip at the inlet to the outer spool to the hub at the inlet to the inner spool. This tip stall ultimately resulted in compressor surge in the mid-speed region, and necessitated inter-compressor air bleed. Interstage pressure measurements during acceleration to the compressor stall limit indicated that rotating stall was not a necessary condition for compressor surge and that, at the critical stall point, the circumferential interstage pressure distribution was uniform. The exit-stage group of the inner spool was first t o stall; then, the stages upstream stalled in succession until the inlet stage of the outer spool was stalled. With a sufficiently high fuel rate, the process repeated with a cycle time of about 0.1 second. It was possible to construct reproducible stage stall lines as a function of compressor speed from the stage stall points of several such compressor surges. This transient stall line was checked by computing the stall line from a steady-state stage-loading curve. Good agreement between the stage stall lines was obtained by these two methods.

Wallner, Lewis E.↗
NASA NTRS2006

Airborne Observations of the Spatial and Temporal Variability of Tropospheric Carbon Dioxide during the INTEX-B Campaign

The Intercontinental Chemical Transport Experiment-North America (INTEX-NA) is an international field campaign envisioned to investigate the transport and transformation of gases and aerosols on transcontinental/intercontinental scales and assess their impact on air quality and climate. Phase B (INTEX-B) of the mission was conducted during a 10- week period from March 1 to May 15, 2006 and focused initially on pollution outflow from the Mexico City Metropolitan Area, later addressing the transport of pollution from Asia to North America during springtime meteorological conditions. During the deployment, fast-response (1-s resolution) CO2 measurements were recorded aboard the NASA DC-8 providing valuable regional-scale information on carbon sources and sinks over sparsely sampled areas of North America and adjacent ocean basins. When coupled with the enormously sophisticated chemistry payload on the DC-8, these measurements collectively afford extremely powerful multi-tracer constraints for carbon source/sink attribution. Preliminary examination of the two data sets from the INTEX-B campaign, acquired one month apart, reveals not only the influence of the CO2 seasonal cycle, but also the preponderance of human population and industrial activity in the northern hemisphere. In this presentation, a synergy of the ensemble of airborne and surface observations, bottomup emission inventories, as well as transport history are invoked in a GIS framework to elucidate the source/sink processes reflected in the observations. The airborne CO2 data, along with simultaneous surface measurements (e.g. NOAA ESRL), are examined to establish the vertical distribution and variability of CO2 as a function of location. The role of localized sources, long-range transport, the biosphere, stratospheric exchange, and dynamical processes on the CO2 spatial variability observed throughout the tropospheric column will be discussed.

Vay, Stephanie A.↗
NASA NTRS2008

The Chase to Capture Gamma Ray Bursts

Gamma-ray bursts are the most powerful explosions in the universe, thought to be the birth cries of black holes. It has taken 40 years of international cooperation and competition to begin to unravel the mystery of their origin. The most recent chapter in this field is being written by the SWIFT mission, a fast-response satellite with 3 power telescopes. An international team from countries all over the world participates in the chase to capture the fading light of bursts detected by SWIFT. This talk will discuss the challenges and excitement of building this space observatory. New results will be presented on our growing understanding of exploding stars and fiery mergers of orbiting stars.

Gehrels, Neil↗
NASA NTRS2007

NASA Tech Briefs, September 2007

Topics covered include; Rapid Fabrication of Carbide Matrix/Carbon Fiber Composites; Coating Thermoelectric Devices To Suppress Sublimation; Ultrahigh-Temperature Ceramics; Improved C/SiC Ceramic Composites Made Using PIP; Coating Carbon Fibers With Platinum; Two-Band, Low-Loss Microwave Window; MCM Polarimetric Radiometers for Planar Arrays; Aperture-Coupled Thin-Membrane L-Band Antenna; WGM-Based Photonic Local Oscillators and Modulators; Focal-Plane Arrays of Quantum-Dot Infrared Photodetectors; Laser Range and Bearing Finder With No Moving Parts; Microrectenna: A Terahertz Antenna and Rectifier on a Chip; Miniature L-Band Radar Transceiver; Robotic Vision-Based Localization in an Urban Environment; Programs for Testing an SSME-Monitoring System; Cathodoluminescent Source of Intense White Light; Displaying and Analyzing Antenna Radiation Patterns; Payload Operations Support Team Tools; Space-Shuttle Emulator Software; Soft Real-Time PID Control on a VME Computer; Analyzing Radio-Frequency Coverage for the ISS; Nanorod-Based Fast-Response Pressure-Sensitive Paints; Capacitors Would Help Protect Against Hypervelocity Impacts; Diaphragm Pump With Resonant Piezoelectric Drive; Improved Quick-Release Pin Mechanism; Designing Rolling-Element Bearings; Reverse-Tangent Injection in a Centrifugal Compressor; Inertial Measurements for Aero-assisted Navigation (IMAN); Analysis of Complex Valve and Feed Systems; Improved Path Planning Onboard the Mars Exploration Rovers; Robust, Flexible Motion Control for the Mars Explorer Rovers; Solar Sail Spaceflight Simulation; Fluorine-Based DRIE of Fused Silica; Mechanical Alloying for Making Thermoelectric Compounds; Process for High-Rate Fabrication of Alumina Nanotemplates; Electroform/Plasma-Spray Laminates for X-Ray Optics; An Automated Flying-Insect Detection System; Calligraphic Poling of Ferroelectric Material; Blackbody Cavity for Calibrations at 200 to 273 K; KML Super Overlay to WMS Translator; High-Performance Tiled WMS and KML Web Server; Modeling of Radiative Transfer in Protostellar Disks; Composite Pulse Tube; Photometric Calibration of Consumer Video Cameras; Criterion for Identifying Vortices in High- Pressure Flows; Amplified Thermionic Cooling Using Arrays of Nanowires; Delamination-Indicating Thermal Barrier Coatings; Preventing Raman Lasing in High-Q WGM Resonators; Procedures for Tuning a Multiresonator Photonic Filter; Robust Mapping of Incoherent Fiber-Optic Bundles; Extended-Range Ultrarefractive 1D Photonic Crystal Prisms; Rapid Analysis of Mass Distribution of Radiation Shielding; Modeling Magnetic Properties in EZTB; Deep Space Network Antenna Logic Controller; Modeling Carbon and Hydrocarbon Molecular Structures in EZTB; BigView Image Viewing on Tiled Displays; and Imaging Sensor Flight and Test Equipment Software.

Source record↗
NASA NTRS2016

Wavenumber-frequency Spectra of Pressure Fluctuations Measured via Fast Response Pressure Sensitive Paint

The recent advancement in fast-response Pressure-Sensitive Paint (PSP) allows time-resolved measurements of unsteady pressure fluctuations from a dense grid of spatial points on a wind tunnel model. This capability allows for direct calculations of the wavenumber-frequency (k-ω) spectrum of pressure fluctuations. Such data, useful for the vibro-acoustics analysis of aerospace vehicles, are difficult to obtain otherwise. For the present work, time histories of pressure fluctuations on a flat plate subjected to vortex shedding from a rectangular bluff-body were measured using PSP. The light intensity levels in the photographic images were then converted to instantaneous pressure histories by applying calibration constants, which were calculated from a few dynamic pressure sensors placed at selective points on the plate. Fourier transform of the time-histories from a large number of spatial points provided k-ω spectra for pressure fluctuations. The data provides first glimpse into the possibility of creating detailed forcing functions for vibro-acoustics analysis of aerospace vehicles, albeit for a limited frequency range.

Pressure Sensitive Paint↗
NASA NTRS2019

Two-Point Focused Laser Differential Interferometry Second-Mode Measurements at Mach 6

A two-point focused laser differential interferometer (FLDI) is used to make measurements of density fluctuations on a 7 degree half-angle cone in a Mach 6 flow. The system was first characterized in the laboratory using laser induced breakdown to provide a well defined density fluctuation. The speed of the shock wave generated by the breakdown is verified using simultaneous high-speed schlieren. The FLDI system is then installed at the NASA Langley 20-Inch Mach 6 air tunnel to make measurements in the boundary layer of the 7 degree half-angle cone model and in the tunnel freestream for a unit Reynolds number range of 3.0 to 8.22 x 10(exp 6)/ft. Second-mode packets are visible in the spectra, with peak frequencies increasing linearly and peak amplitude increasing as a function of unit Reynolds number. The two-point measurement allows for the calculation of the second-mode wavepacket speeds, which propagate between 88% and 92% of the freestream velocity of the tunnel for all Reynolds numbers. The FLDI measurements are compared to surface-mounted fast-response pressure transducer measurements, where second-mode frequencies and wavepacket speeds are in good agreement.

Weisberger, Joshua M.↗
NASA NTRS2020

1- by 1-Foot Supersonic Wind Tunnel Sidewall Flowfield Compression Plate Study

A method for locally increasing the dynamic pressure in the test section of a supersonic wind tunnel is investigated from a theoretical, computational and experimental perspective, culminating in a reduced-scale, proof-of-concept test at Mach 3.44. Symmetric, variable-angle compression plates along the test section sidewalls generate oblique shockwaves to elevate the test section dynamic pressure (q). The experimental effort utilizes boundary-layer pitot rakes to sample the incoming flow near the floor, pitot and static rakes to measure the high-q core flow and numerous surface taps to map out the static pressure distribution along the floor, ceiling and sidewalls. A reliable and robust starting procedure is developed to establish supersonic flow in the test section and behind the compression plates. A characterization of the incoming floor boundary layer reveals previously documented features (such as a bulge toward the centerline) and an unexpected (and as-yet-unexplained) thickening of the boundary layer with increasing Reynolds number around total pressures of 40–60 psia. The high-q core flow is characterized for eight compression plate angles (4.0–8.0°), eight tunnel total pressures (20–139 psia) and three axial stations (24.95–27.35 inches). The peak dynamic pressure rise exceeds expectations. At conditions relevant to full-scale testing (6.0° and 139 psia), the dynamic pressure increases by a factor of 1.73, the Mach number becomes 2.85 and the total pressure drops imperceptibly. Basic distortion metrics show transverse non-uniformity of less than 5 %. Limited spatial resolution in the static rake measurements warrants additional, higher fidelity testing or computational analysis. Surface-mounted, fast-response instrumentation suggests minimal unsteadiness in the flow, less than a few percent of the mean (comparable to the sensor accuracy).

Wind tunnel testing, test techniques/methods, dyna↗
NASA NTRS2021

Computational Fluid Dynamics Simulations of the Transonic Dynamics Tunnel Airstream Oscillator System

This paper presents computational fluid dynamics simulations of the flow in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT) with the airstream oscillator system (AOS) in operation. Test section flow angle can be modulated using sinusoidally oscillating vanes which are located in pairs within the contraction section of the tunnel circuit. A compilation of previously published experimental data for validation has been reviewed that contains hot-wire anemometer and fast-response probe data acquired in an empty test section with the vanes oscillating in-phase and out-of-phase. These experimental data have not previously been compared with computational results. The present results provide an opportunity for validation of the simulations of the sinusoidal AOS flow field in the TDT test section. Computed tunnel centerline, lateral and cross-section contour data of flow angle and vorticity show that resolving the vane tip vortex is critical to accurately predicting the test section center flow angle. The computed results show, as do the experimental data, what appears to be a resonance at higher frequencies. It is currently not known what is the cause of that resonance. Further refinement of the mesh is expected to improve the comparisons with experimental data

Robert E Bartels↗
NASA NTRSDate not supplied

Measurements of Freestream Fluctuations in the Langley Research Center Unitary Plan Wind Tunnel

Measurements of the freestream disturbance environment were made in the high Machnumber leg of the NASA Langley Research Center Unitary Plan Wind Tunnel. The un-steady pitot pressure fluctuations and mass-flux fluctuations were measured with fast-response pressure transducers and hot wires, respectively. These were the first directmeasurements of the disturbance environment made in this facility’s test section. Thespectral content of the disturbances in the freestream show a significant amount of powerat frequencies below 100 Hz. At Mach 3.5 and Mach 4.6, there is also a broad peak in thespectra spanning from 100 Hz to 1 kHz. The RMS amplitude of the freestream mass-fluxfluctuations ranges from approximately 0.5% to 2.5%. The amplitude of the disturbancesincreases with Mach number but does not vary significantly with Reynolds number andstreamwise station. At Mach 2.4, the amplitude of the pitot pressure and mass-flux fluctu-ations is higher at the bottom of the tunnel than in the center of the tunnel. This increaseis likely due to the presence of a vortical structure near the bottom of the tunnel. Com-pared to similar facilities that operate in the same Mach number range, the freestreamdisturbance amplitudes follow similar trends and are within the same order of magnitude

freestream disturbance↗
NASA NTRSDate not supplied

Launch Vehicle Loads Analysis Using Pressure-Sensitive Paint

Pressure transducers have been the instrumentation of choice for measuring unsteady flow phenomena. With recent advances in high-speed cameras, high-powered LEDs, and fast-response, pressure-sensitive paint, the unsteady pressure-sensitive paint (uPSP) technique has become a valuable alternative for production wind tunnel facilities, enabling time-resolved measurements of unsteady pressure fluctuations over a dense spatial grid on a wind tunnel model. Launch vehicle ground tests have proven to be a particularly well-matched application for uPSP due to the high signal level relative to tunnel background acoustics, relatively simple camera optical access, and rigidity of the model in wind-on test conditions. This presentation will highlight recent advances in data reduction of uPSP measurement data from recent launch vehicle wind tunnel tests at the NASA Ames Unitary Plan Wind Tunnel Complex (UPWT). The system can provide both localized surface pressure spectra as well as regional or zonal estimates of turbulence correlation model parameters. In addition, integrated vehicle-scale loads can be provided for buffet analysis. Data is reduced at the on-premise NASA Advanced Supercomputer (NAS) Division for just-in-time delivery of results during an ongoing wind tunnel test.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

Launch Vehicle Loads Analysis Using Pressure-Sensitive Paint

Pressure transducers have been the instrumentation of choice for measuring unsteady flow phenomena. With recent advances in high-speed cameras, high-powered LEDs, and fast-response, pressure-sensitive paint, the unsteady pressure-sensitive paint (uPSP) technique has become a valuable alternative for production wind tunnel facilities, enabling time-resolved measurements of unsteady pressure fluctuations over a dense spatial grid on a wind tunnel model. Launch vehicle ground tests have proven to be a particularly well-matched application for uPSP due to the high signal level relative to tunnel background acoustics, relatively simple camera optical access, and rigidity of the model in wind-on test conditions. This presentation will highlight recent advances in data reduction of uPSP measurement data from recent launch vehicle wind tunnel tests at the NASA Ames Unitary Plan Wind Tunnel Complex (UPWT). The system can provide both localized surface pressure spectra as well as regional or zonal estimates of turbulence correlation model parameters. In addition, integrated vehicle-scale loads can be provided for buffet analysis. Data is reduced at the on-premise NASA Advanced Supercomputer (NAS) Division for just-in-time delivery of results during an ongoing wind tunnel test.

pressure-sensitive paint↗
NASA NTRSDate not supplied

NASA Small Engine Components Compressor Test Facility: High Efficiency Centrifugal Compressor Vaneless Diffuser and Transition Duct Configurations

The original vaned configuration of the High Efficiency Centrifugal Compressor (HECC) was developed with aggressive design targets to facilitate advancement of state-of-the-art technology in gas turbine compressors. This work documents modifications to the Small Engine Components Compressor Test Facility to support testing of the HECC vaneless diffuser and transition duct configurations, both of which are open geometries. These configurations were developed as follow-up studies to improve understanding of the differences between the predicted and actual performance of the original HECC vaned diffuser stage. Specifically, the vaneless diffuser was designed to provide the impeller with ideal exit conditions such that the impeller performance could be isolated from downstream stationary components, and the additively manufactured transition duct inlet configuration enables investigation into the effects of the inlet flow path on the stage performance. Features of note in the facility are active clearance control, bleed flow regulation, modular inlet configurations, and steady-state and fast-response instrumentation throughout the flow path. Details of the facility and instrumentation are presented as well as the baseline performance of the compressor stage. The geometry, performance, and detailed aerodynamic data have been made available to the public at https://storage.googleapis.com/heccdata/NASA-HECC-Data-Archive.zip.

centrifugal compressor↗
NASA NTRSDate not supplied

Hypersonic Fluid-Thermal-Structural Interactions on a Compression Ramp with an Embedded Compliant Panel

The fluid-thermal-structural interactions of a compliant panel embedded in a compression ramp are explored experimentally at Mach 6. The panel structural response is investigated for turbulent and transitional shock-wave/boundary-layer interactions at five distinct interaction strengths and up to four different pressure differentials. Upstream of the compression corner, fast-response piezoresistive pressure transducers show the feedback of the panel vibrations and static deflection on the upstream pressure fluctuations. The magnitude of the pressure fluctuation rms shows a reduction in the upstream disturbances when a pressure differential is applied across the compliant panel. Photogrammetry and IR thermography are used simultaneously to measure the panel deformations and surface temperature. Panel deformation, frequency shifting, and frequency bifurcation are consistent with post-thermal-buckling behavior.

hypersonic↗
NASA NTRSDate not supplied

NASA Small Engine Components Compressor Test Facility: High Efficiency Centrifugal Compressor Vaneless Diffuser and Transition Duct Configurations

The original vaned configuration of the High Efficiency Centrifugal Compressor (HECC) was developed with aggressive design targets to facilitate advancement of state-of-the-art technology in gas turbine compressors. This work documents modifications to the Small Engine Components Compressor Test Facility to support testing of the HECC vaneless diffuser and transition duct configurations, both of which are open geometries. These configurations were developed as follow-up studies to improve understanding of the differences between the predicted and actual performance of the original HECC vaned diffuser stage. Specifically, the vaneless diffuser was designed to provide the impeller with ideal exit conditions such that the impeller performance could be isolated from downstream stationary components, and the additively manufactured transition duct inlet configuration enables investigation into the effects of the inlet flow path on the stage performance. Features of note in the facility are active clearance control, bleed flow regulation, modular inlet configurations, and steady-state and fast-response instrumentation throughout the flow path. Details of the facility and instrumentation are presented as well as the baseline performance of the compressor stage. The geometry, performance, and detailed aerodynamic data have been made available to the public at https://storage.googleapis.com/hecc-data/NASA-HECC-Data-Archive.zip.

centrifugal compressor↗
NASA NTRSDate not supplied

A Machine Learning Approach for the Remote Sensing Retrieval of Oil Spills from Polarimetric Measurements

The Fresnel laws of specular reflection directly connect remote sensing observations of light polarization within the sunglint region to the ocean surface refractive index. This parameter is instrumental to identify areas affected by oil, or any other floating substance capable of modifying the refractive index of pure seawater. In preparation for the NASA Plankton, Aerosol, ocean Ecosystem (PACE) mission, we are developing an advanced retrieval scheme that exploits such measurements to deliver the refractive index as an operational product. The original method was developed based on observations of the airborne Research Scanning Polarimeter. Here we present several aspects related to the extension of this technique to the PACE HARP-2 sensor (especially regarding the projected accuracy), and discuss preliminary results obtained by applying neural-network trainings to look-up tables produced with the forward radiative transfer code, with the goal of improving the computational performance. Success in the final implementation will guarantee a version of the retrieval algorithm suitable to fast-response needs and disaster management.

machine learning↗
NASA NTRSDate not supplied

Spectral Proper Orthogonal Decomposition of uPSP Measurements in Recent NASA Ames Wind Tunnel Test

This paper discusses Spectral Proper Orthogonal Decomposition (SPOD) of the Unsteady Pressure-Sensitive Paint (uPSP) measurements in recent NASA Ames wind tunnel test. The uPSP measurements were collected using Innovative Scientific Solutions, Inc. (ISSI) Porous, Fast-Response Pressure-Sensitive Paint (FP-XXX), 40 ISSI four-inch air-cooled Light-Emitting Diodes (LEDs), and 8 Phantom v2512 high-speed cameras at 10,000 frames per second in the Launch Vehicle Demo Test (LVDT) of the Space Launch System (SLS) Block 1B crew vehicle in the 11-by 11-foot transonic test section of the Unitary Plan Wind Tunnel (UPWT) at NASA Ames Research Center in April 2024. Fig. 1 shows the scale model of the SLS launch vehicle installed in the wind tunnel during the test.

Aeroacoustics↗
NASA NTRSDate not supplied

Spectral Proper Orthogonal Decomposition of uPSP Measurements in Recent NASA Ames Wind Tunnel Test

This paper discusses Spectral Proper Orthogonal Decomposition (SPOD) of the Unsteady Pressure-Sensitive Paint (uPSP) measurements in recent NASA Ames wind tunnel test. The uPSP measurements were collected using Innovative Scientific Solutions, Inc. (ISSI) porous, fast-response pressure-sensitive paint, 40 ISSI four-inch air-cooled Light-Emitting Diodes, and 8 Phantom v2512 high-speed cameras at 10,000 frames per second in the uPSP Launch Vehicle Demonstration Test (LVDT) of the Space Launch System (SLS) vehicle in the 11-by 11-foot transonic test section of the Unitary Plan Wind Tunnel at NASA Ames Research Center in April 2024. SPOD is derived from a space-time proper orthogonal decomposition problem for statistically stationary flows. SPOD modes are determined in the frequency domain. Each SPOD mode oscillates at a single frequency. SPOD can be viewed as an extension of the Discrete Fourier Transform composition and the Dynamic Mode Decomposition. In this paper, the outputs of SPOD of the uPSP measurements in the uPSP LVDT are presented and the effectiveness of SPOD in the identification, diagnosis and analysis of the aerodynamic and aeroacoustic phenomena is demonstrated. The unsteady and dynamic property of the pressure field on the surface of the SLS Block 1B crew vehicle is presented with the visualization of the SPOD modes of the uPSP measurements in the tests of a Mach sweep run of the uPSP LVDT. The SPOD outputs were generated with the execution in parallel of a code in Python, with the library of Message Passing Interface for parallel processing, on the NASA Pleiades supercomputer. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities Portfolio Office.

Aeroacoustics↗