Search NASA⌕ Search

SEARCH · Search NASA

Results for “high loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Gasoline-like Fuel Effects on High-load, Boosted HCCI Combustion Employing Negative Valve Overlap Strategy

In recent years a number of studies have demonstrated that boosted operation combined with external EGR is a path forward for expanding the high load limit of homogeneous charge compression ignition (HCCI) operation with the negative valve overlap (NVO) valve strategy. However, the effects of fuel composition with this strategy have not been fully explored. In this study boosted HCCI combustion is investigated in a single-cylinder research engine equipped with direct injection (DI) fueling, cooled external exhaust gas recirculation (EGR), laboratory pressurized intake air, and a fully-variable hydraulic valve actuation (HVA) valve train. Three fuels with significant compositional differences are investigated: regular grade gasoline (RON = 90.2), 30% ethanol-gasoline blend (E30, RON = 100.3), and 24% iso-butanol-gasoline blend (IB24, RON = 96.6). Results include engine loads from 350 to 800 kPa IMEPg for all fuels at three engine speeds 1600, 2000, and 2500 rpm. All operating conditions achieved thermal efficiency (gross indicated efficiency) between 38 and 47%, low NOX emissions ( 0.1 g/kWh), and high combustion efficiency ( 96.5%). Detailed sweeps of intake manifold pressure (atmospheric to 250 kPaa), EGR (0 25% EGR), and injection timing are conducted to identify fuel-specific effects. The major finding of this study is that while significant fuel compositional differences exist, in boosted HCCI operation only minor changes in operational conditions are required to achieve comparable operation for all fuels. In boosted HCCI operation all fuels were able to achieve matched load-speed operation, whereas in conventional SI operation the fuel-specific knock differences resulted in significant differences in the operable load-speed space. Although all fuels were operable in boosted HCCI, the respective air handling requirements are also discussed, including an analysis of the demanded turbocharger efficiency.

efficiency↗

The Alternating Surface Segmented Lap Joint: a Design for Thin Highly Loaded Joints

The combination of thin airfoil sections and high aerodynamic loads on many wind tunnel models presents a major problem for attachment of flap elements. Conventional methods of attaching fixed control elements such as lap and tongue-in-groove joints are not rigid enough to provide surface continuity required in high Reynolds number research. For the extreme cases, the solution has been to fabricate separate wings for each flap setting with the flap element being and integral part of the wing. Here an attractive solution to this problem, the alternating surface segmented lap joint, is discussed. This joint provides increased rigidity and lower stress levels than conventional joints. Additionally, attachment fastener loading is low and the joint can be designed to accommodate high shear levels due to bending without the use of dowel pins.

Watkins, V. E., Jr.↗

Catalytic Electrolyte Additive for High-Loading and Lean Electrolyte Li–S Batteries

The cycle life of high-energy Li–S cells is largely constrained by the quick electrolyte depletion. LiNO 3 has been a well-established additive known for protecting the Li metal anode and stabilizing the battery from polysulfide “shuttling”. However, it can be depleted prematurely and can pose safety risks when exposed to carbon, sulfur, or Li metal under harsh conditions. Here, in this study, LiPO 2 F 2 was explored as a safe and durable alternative additive in ether-based electrolytes. LiPO 2 F 2 demonstrates superior performance in Li/S batteries, especially under high sulfur loading (∼4 mg/cm 2 ) and lean electrolyte conditions (E/S = 4), achieving a long-term cycling stability of 40%, compared to 14.7% with LiNO 3 . This additive facilitates the disproportionation of polysulfides, reducing their dissolution and mitigating the shuttle effect. Additionally, LiPO 2 F 2 promotes the formation of a stable solid-electrolyte interphase (SEI) composed of inorganic anion-derived species, improving the battery’s overall stability and functionality. These findings blaze a trail in the design of safer and more durable electrolytes for Li–S batteries.

Li-S batteries↗

High Load Expansion of Catalytic EGR-Loop Reforming under Stoichiometric Conditions for Increased Efficiency in Spark Ignition Engines

The use of fuel reformate from catalytic processes is known to have beneficial effects on the spark-ignited (SI) combustion process through enhanced dilution tolerance and decreased combustion duration, but in many cases reformate generation can incur a significant fuel penalty. In a previous investigation, the researchers showed that, by controlling the boundary conditions of the reforming catalyst, it was possible to minimize the thermodynamic expense of the reforming process, and in some cases, realize thermochemical recuperation (TCR), a form of waste heat recovery where exhaust heat is converted to usable chemical energy. The previous work, however, focused on a relatively light-load engine operating condition of 2000 rpm, 4 bar brake mean effective pressure (BMEP). The present investigation demonstrates that this operating strategy is applicable to higher engine loads, including boosted operation up to 10 bar BMEP. By controlling the reforming catalyst boundary conditions, it is possible to achieve fuel reforming without experiencing high temperature exotherms that could be damaging to the catalyst. Additionally, the thermodynamic air handling consequences of operating a highly dilute strategy at high loads is quantified. Furthermore the results confirm that this operating strategy provides an efficiency benefit at all conditions investigated, with relative efficiency increases of 3-6%, and is therefore applicable over wider regions of the engine operating map.

42 ENGINEERING↗

Polymer Brushes under High Load

Polymer coatings are frequently used to provide repulsive forces between surfaces in solution. After 25 years of design and study, a quantitative model to explain and predict repulsion under strong compression is still lacking. Here, we combine experiments, simulations, and theory to study polymer coatings under high loads and demonstrate a validated model for the repulsive forces, proposing that this universal behavior can be predicted from the polymer solution properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of Engine Control Authority on HCCI Combustion as the High Load Limit is Approached

While the potential emissions and efficiency benefits of homogeneous charge compression ignition (HCCI) combustion are well known, realizing the potentials on a production intent engine presents numerous challenges. In this study we focus on characterizing the authority of the available engine controls as the high load limit of HCCI combustion is approached. The experimental work is performed on a boosted single-cylinder research engine equipped with direct injection (DI) fueling, cooled external exhaust gas recirculation (EGR), and a hydraulic valve actuation (HVA) valve train to enable the negative valve overlap (NVO) breathing strategy. Valve lift and duration are held constant while phasing is varied in an effort to make the results as relevant as possible to production intent cam-based variable valve actuation (VVA) systems on multi-cylinder engines. Results presented include engine loads from 350 to 650 kPa IMEPnet and manifold pressure from 98 to 190 kPaa at 2000 rpm. It is found that in order to increase engine load to 650 kPa IMEPnet, it is necessary to increase manifold pressure and external EGR while reducing the NVO duration. Both NVO duration and fuel injection timing are effective means of controlling combustion phasing, with NVO duration being a coarse control and fuel injection timing being a fine control. NOX emissions are low throughout the study, with emissions below 0.1 g/kW-h at all boosted HCCI conditions, while good combustion efficiency is maintained (>96.5%). Net indicated thermal efficiency increases with load up to 600 kPa IMEPnet, where a peak efficiency of 41% is achieved. Results of independent parametric investigations are presented on the effect of external EGR, intake effect of manifold pressure, and the effect of NVO duration. It is found that increasing EGR at a constant manifold pressure and increasing manifold pressure at a constant EGR rate both have the effect of retarding combustion phasing. It is also found that combustion phasing becomes increasingly sensitive to NVO duration as engine load increases. Finally, comparisons are made between three commonly used noise metrics (AVL noise meter, ringing intensity (RI), and maximum pressure rise rate (MPRR)). It is found that compared to the AVL noise meter, RI significantly underestimates combustion noise under boosted conditions.

control sensitivity↗

Simultaneous Control of Unburned NH 3 and NO x Emissions From High Load Dual-Fuel Ammonia Operation on a High-Speed Diesel Engine Using a Cu-SCR System

Dual-fuel ammonia strategies are being investigated as a promising way to utilize NH 3 as an alternative fuel for internal combustion engines in the maritime sector. One of the remaining barriers to implementing dual-fuel NH 3 combustion strategies is understanding ways to minimize unburned NH 3 and nitrogen oxide (NO x ) emissions from these engines, both of which are elevated relative to a conventional diesel baseline. Selective catalytic reduction (SCR) systems are widely used for lean NO x emission controls for engines across transportation and stationary energy applications. SCR systems use a reducing agent, such as NH 3 , to react with NO x in the exhaust, converting it into nitrogen and water. Typically, NH 3 is injected into the exhaust as a urea solution. In dual-fuel NH 3 engines, where unburned NH 3 is present in the exhaust, an SCR system could be used to mitigate both NH 3 and NO x emissions. The presented work evaluates a commercial copper-zeolite SCR and ammonia slip catalyst system, designed for on-road diesel engine applications, for controlling unburned NH 3 and NO x emissions from a dual-fuel NH 3 combustion engine. The aftertreatment system was installed downstream of a single-cylinder four-stroke diesel engine that has been modified for dual-fuel ammonia use. Furthermore, the emissions were characterized by using a Fourier transform infrared spectrometer for both late- and early-injection diesel pilot strategies over three air–fuel equivalence ratios spanning from 1.6 to 1.0 at 1200 rpm and 12.6 bar IMEP g condition (with greater than 95% ammonia energy fraction). Initial findings indicate that the SCR achieves more than 99% NO x conversion with less than 50 ppm NH 3 slip at air–fuel equivalence ratios greater than 1.4 at the operating conditions investigated. However, these benefits are accompanied by additional N 2 O emissions that are formed over the Cu-SCR.

Catalysts↗

Capability Extension to the Turbine Off-Design Computer Program AXOD With Applications to the Highly Loaded Fan-Drive Turbines

The axial flow turbine off-design computer program AXOD has been upgraded to include the outlet guide vane (OGV) into its acceptable turbine configurations. The mathematical bases and the techniques used for the code implementation are described and discussed in lengths in this paper. This extended capability is verified and validated with two cases of highly loaded fan-drive turbines, designed and tested in the V/STOL Program of NASA. The first case is a 4 1/2-stage turbine with an average stage loading factor of 4.66, designed by Pratt & Whitney Aircraft. The second case is a 3 1/2-stage turbine with an average loading factor of 4.0, designed in-house by the NASA Lewis Research Center (now the NASA Glenn Research Center). Both cases were experimentally tested in the turbine facility located at the Glenn Research Center. The processes conducted in these studies are described in detail in this paper, and the results in comparison with the experimental data are presented and discussed. The comparisons between the AXOD results and the experimental data are in excellent agreement.

Chen, Shu-cheng S.↗

Single-stage experimental evaluation of low aspect ratio, highly loaded blading for compressors. Part 9: Stage F and stage G, volume 1

Two single-stage, 0.77 hub/tip ratio axial-flow compressors were tested to evaluate the effectiveness of low aspect ratio blading as a means of obtaining higher stage loadings. One compressor, designated Stage F, was comprised of circular arc blading with an aspect ratio of 0.9 for both the rotor and stator. This compressor was tested with uniform inlet flow, hub radial, tip radial, and 180 deg arc circumferential inlet distortion. The second compressor, designated Stage G, was comprised of multiple circular arc blading with an aspect ratio of 1.0 for both the rotor and stator. This compressor was tested with uniform inlet flow only. Design rotor tip speeds for Rotor F and Rotor G were 285 m/sec (934 ft/sec) and 327 m/sec (1,074 ft/sec) respectively. Both stages operated at high loading levels with adequate efficiency and operating range. The peak efficiencies and corresponding average stage diffusion factors for Stages F and G at design rotor speed were 86.4% and 84.1% and 0.59 and 0.55 respectively. The surge margin at peak efficiency for Stage F was 12.6% and the corresponding value for Stage G was 16.5%. Both stages experienced a loss in efficiency with increasing rotor speed; however, the multiple circular arc rotor delayed the characteristic loss in efficiency within increasing Mach number to higher Mach number.

Cheatham, J. G.↗

Operando Neutron Imaging of Lithium Flux and Gradient Cathode Design for Enhanced Kinetics in High‐Loading All‐Solid‐State Li─S Batteries

All-solid-state Li–sulfur batteries (ASSLSBs) are considered promising candidates for next-generation energy storage owing to their inherent safety, high energy density, and abundant sulfur resources. However, slow redox kinetics greatly limit sulfur utilization during solid-solid sulfur reactions, leading to significant challenges to achieve efficient performance in high-mass-loading ASSLSBs. Here, operando neutron image is employed to directly visualize, for the first time, that sluggish Li + transport kinetics and the uneven distribution of Li + during cathodic reactions are critical factors limiting sulfur conversion. To address this issue, gradient cathode architectures comprising three and five layers are designed, in which catholyte concentrations are strategically varied to optimize Li-ion flux and enhance ionic conductivity of the whole composite cathode electrode. Operando neutron imaging distinctly visualizes and confirms that three-layer gradient approach significantly enhances Li-ion mobility, resulting in more uniform redox reactions and greatly improved sulfur utilization compared to traditional non-gradient structures. Consequently, the three-layer gradient cathode achieves superior rate performance and reduced electrode polarization at high sulfur mass loadings of 4.5 and 6.0 mg cm −2 . Furthermore, the applicability and scalability of this design are demonstrated in a five-layer gradient cathode architecture, achieving an impressive discharge specific capacity increase from 656 mAh g −1 (three-layer gradient) to 1232 mAh g −1 at 1/20 C for ultra-high sulfur loading of 7.5 mg cm −2 . In conclusion, this innovative gradient cathode design offers substantial advancements in understanding and overcoming Li-ion transport limitations, paving the way toward practical, high-energy-density ASSLSBs.

25 ENERGY STORAGE↗

Laser ablation of high-loading Li-ion battery electrodes improves accessible capacity and cycle life for Behind-the-Meter Storage

Adoption of Behind-the-Meter Storage (BTMS) requires design of batteries that enable high safety, long cycle life, and low cost at the system level. Pairing Li 4 Ti 5 O 12 (LTO) with LiMn 2 O 4 (LMO) achieves targets related to safety and cycle life, but these materials' low energy densities contribute to higher cost at the system scale. Increasing electrode loading is a simple approach to improve energy density, but comes with a trade-off in electrode utilization due to long, tortuous Li + diffusion pathways. Here, laser ablation is used to microstructure (pattern) high-loading electrodes to enhance electrode performance through improved Li + diffusion pathways. Four cell types, comprising combinations of standard or patterned anode and cathode, were prepared to evaluate the effects of laser ablation at each electrode. A rate test shows that patterning electrodes enhances active material utilization at ≳1C rates. Patterning the cathode yields the most benefit, as cells with a patterned cathode demonstrate a ~20% higher accessible capacity than those without at 1.4C. Additionally, 1C capacity retention of cells with patterned cathode (91% through 3000 cycles) is significantly improved over cells with only the anode patterned (64%) and non-patterned electrodes (50%). Characterization of post-mortem cells before and after refreshing their electrolyte suggests that 1C capacity retention is improved by mitigation of electrode "dry-out". We hypothesize that the microstructure acts as a reservoir of additional electrolyte, or a path for gas to escape, so that active material remains wetted throughout long-term cycling, and/or the microstructure may reduce localized, gas-forming overpotentials in the high-loading electrode.

25 ENERGY STORAGE↗

Wettable carbon felt framework for high loading Li-metal composite anode

Li metal anode has received extensive attention due to its high specific capacity and low potential vs. Li/Li + for lithium batteries. However, dendrite growth, volume change and "dead" Li formation during cycling hinder its practical application. Here we report an innovated cuprite-coated carbon felt as current collector, with ultralight 3D framework and significantly improved Li-metal loading through thermal infusion. The Li-metal anode has a high Li content of 90 wt.%. The cuprite coating improves the lithiophilicity of carbon felt remarkably, due to the surface affinity reaction between cuprite and Li. Moreover, the porous carbon felt provides good electronic connection and buffer space to accommodate volume change during Li stripping/plating. It leads to uniformly distributed local current density and preference of Li stripping/plating in the highly dispersed concave areas, with suppressed formation of dendrites and “dead” Li. The Li composite electrode shows excellent cycle stability with low polarization in both symmetric and full cells. Hence, this work opens a new approach for the development of high loading Li composite anodes for advanced Li metal batteries.

25 ENERGY STORAGE↗

Effects of Unsteady Flow Interactions on the Performance of a Highly-Loaded Transonic Compressor Stage

The primary focus of this paper is to investigate the loss sources in an advanced GE transonic compressor design with high reaction and high stage loading. This advanced compressor has been investigated both experimentally and analytically in the past. The measured compressor efficiency is significantly lower than the efficiency calculated with various existing tools based on RANS and URANS. The general understanding is that some important flow physics in this modern compressor design are not represented in the current tools. To pinpoint the source of the efficiency miss, an advanced test with detailed flow traverse was performed for the front one and a half stage at the NASA Glenn Research Center. In the present paper, a Large Eddy Simulation (LES) is employed to determine whether a higher-fidelity simulation can pick up any additional flow physics that can explain past efficiency miss with RANS and URANS. The results from the Large Eddy Simulation were compared with the NASA test results and the GE interpretation of the test data. LES calculates lower total pressure and higher total temperature on the pressure side of the stator, resulting in large loss generation on the pressure side of the stator. On the other hand, existing tools based on the RANS and URANS do not calculate this high total temperature and low total pressure on the pressure side of the stator. The calculated loss through the stator from LES seems to match the measured data and the GE data interpretation. Detailed examination of the unsteady flow field from LES indicates that the accumulation of high loss near the pressure side of the stator is due to the interaction of the rotor wake with the stator blade. The strong rotor wake interacts quite differently with the pressure side of the stator than with the suction side of the stator blade. The concave curvature on the pressure side of the stator blade increases the mixing of the rotor wake with the pressure side boundary layer significantly. On the other hand, the convex curvature on the suction side of the stator blade decreases the mixing and the suction side blade boundary layer remains thin. The jet velocity in the rotor wake in the stator frame seems to magnify the curvature effect in addition to inviscid redistribution of wake fluid toward the pressure side of the blade.

LES↗

Scuffing Characteristics of High-Load Rolling/Sliding Contacts Operating in Liquid Oxygen: Effects of Materials and Surface Roughness

This research reports on an experimental study of the effects of materials and surface roughness on the scuffing characteristics of rolling/sliding contacts cooled and lubricated with liquid oxygen. Experiments were carried out under heavy loading with a Hertzian pressure in the range of 2.0 GPa to 3.0 GPa and with a high rolling velocity of up to 48 m/s. For contacts between AISI 440 C stainless-steel elements, the results showed that the scuffing behavior of the system was fairly consistent under a wide range of rolling velocity. Scuffing commenced at a small slide-to-roll ratio of around 0.02, and the scuffing behavior of the contact was not sensitive to surface roughness for the test-sample RMS roughness ranging from 0.02 microns to 0.10 microns. For contacts between 440 C and Si3N4 elements, on the other hand, the scuffing behavior of the system was not very consistent and somewhat unpredictable. The results were sensitive to surface roughness particularly that of the Si3N4 test sample. With well polished test samples, consistent results were obtained; the level of traction was lower than that with a 440 C toroid and scuffing did not take place up to a slide-to-roll ratio of near 0.03. The results strongly suggest that significant hydrodynamic effect can be generated by liquid oxygen under heavy loading and high velocity conditions. The results also suggest that the hydrodynamic action is likely generated by the conventional viscous mechanism as it can be largely destroyed by a narrow circumferential surface scratch running through the central region of the contact.

Chang, L.↗

Extraction of Nitric Acid and Uranium with DEHiBA under High Loading Conditions

We report the mechanism by which high concentrations (1.5 M in n-dodecane) of N,N-di-2-ethylhexylisobutyramide (DEHiBA) extracts HNO 3 and UO 2 (NO 3 ) 2 is under examination. Most prior studies have examined the extractant and the mechanism at a concentration of 1.0 M in n-dodecane, however under the higher loading conditions that can be achieved by a higher concentration of extractant this mechanism could change. Increased extraction of both nitric acid and uranium is observed with an increased concentration of DEHiBA. The mechanisms are examined by thermodynamic modeling of distribution ratios, 15 N NMR, and FTIR spectroscopy coupled with Principal Component Analysis (PCA). Speciation diagrams produced through thermodynamic modeling have been qualitatively reproduced through PCA of the FTIR spectra. The predominant extracted species of HNO 3 (DEHiBA), HNO 3 (DEHiBA) 2 , and UO 2 (NO 3 ) 2 (DEHiBA) 2 are in good agreement with prior literature reports for 1.0 M DEHiBA systems. Evidence for an additional species of either UO 2 (NO 3 ) 2 (DEHiBA) or UO 2 (NO 3 ) 2 (DEHiBA) 2 (HNO 3 ) also contributing to the extraction of uranium species is given.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanocasting SiO 2 into metal–organic frameworks imparts dual protection to high-loading Fe single-atom electrocatalysts

Single-atom catalysts (SACs) have sparked broad interest recently while the low metal loading poses a big challenge for further applications. Herein, a dual protection strategy has been developed to give high-content SACs by nanocasting SiO 2 into porphyrinic metal–organic frameworks (MOFs). The pyrolysis of SiO 2 @MOF composite affords singleatom Fe implanted N-doped porous carbon (FeSA–N–C) with high Fe loading (3.46 wt%). The spatial isolation of Fe atoms centered in porphyrin linkers of MOF sets the first protective barrier to inhibit the Fe agglomeration during pyrolysis. The SiO 2 in MOF provides additional protection by creating thermally stable FeN4/SiO 2 interfaces. Thanks to the high-density FeSA sites, FeSA–N–C demonstrates excellent oxygen reduction performance in both alkaline and acidic medias. Meanwhile, FeSA–N–C also exhibits encouraging performance in proton exchange membrane fuel cell, demonstrating great potential for practical application. More far-reaching, this work grants a general synthetic methodology toward high-content SACs (such as FeSA, CoSA, NiSA). https://doi.org/10.1038/s41467-020-16715-6 OPEN 1

36 MATERIALS SCIENCE↗

High-Loading Single-Atom Catalyst via On-Surface Synthesis of a Metal-Covalent Organic Framework for Oxygen Reduction Reaction

The development of active catalysts with both high metal efficiency and use of earth abundant metals is the ultimate goal for advancing the required commercially viable and sustainable energy conversion technologies of the future. Metal-organic frameworks (MOFs) have emerged as promising candidates due to their high surface area and tunable active sites. Here, this study aims to fabricate a new type of high metal loading single-atom catalysts (SACs) based on 2D metal-organic covalent organic frameworks (MCOFs) with uniform, active and stable Fe-N 3 sites. The MCOFs were synthesized through an on-surface polymerization process using Fe and melamine as precursors. The polymerization steps were characterized using operando high-pressure scanning tunneling microscopy (HP-STM), in situ X-ray photoelectron spectroscopy (XPS), low-temperature STM (LT-STM), and computational calculations. The synthesized MCOFs demonstrated favorable adsorption and activation of O 2 at the Fe-N 3 sites, and it is predicted to be active for the oxygen reduction reaction (ORR). The surface chemistry and functionality of 2D MCOFs can be rationally designed by varying the metal atoms and organic linkers, offering a versatile platform for diverse applications.

25 ENERGY STORAGE↗