Search NASA⌕ Search

SEARCH · Search NASA

Results for “lead sulfide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Current Status and Future Directions of All-Solid-State Batteries with Lithium Metal Anodes, Sulfide Electrolytes, and Layered Ternary Oxide Cathodes

All-solid-state batteries (ASSBs) offer great promise as a next-generation energy storage technology with higher energy density, wider operating temperature range, and improved safety for electric vehicles. ASSBs employing lithium metal anodes (Li), sulfide-based solid-state electrolytes (SSE), and Ni-rich layered transition metal oxide cathodes (LiMO 2 , M = Ni, Mn, Co, Al) are particularly promising due to its superior electrochemical performance compared to other solid-electrolyte systems. However, the battery cycle life at high cathode mass loading and high current is still limited because the failure mechanism is not fully understood. Lithium dendrite growth at the anode or inside a solid electrolyte still represents as a serious risk of cell failure. Interfacial resistance increases attributed to electrolyte decomposition and interfacial void formation at both cathode–electrolyte and anode–electrolyte interfaces lead to gradual capacity fading. In this Review, we present the fundamental challenges and recent scientific understandings of each component in ASSBs. The novel diagnostic tools for these components, especially the interfaces buried under the surface that are often hard for characterization are mainly examined. Lastly, we offer a perspective for future research directions. We hope this Review will provide a timely snapshot of state-of-the-art research progress in ASSBs to accelerate the development of ASSBs.

25 ENERGY STORAGE↗
DOE OSTI2025

Porous and Amorphous Mn x Mo 3 S 13 Chalcogel Electrode for High-Capacity Conversion-Based Lithium-Ion Batteries

While Li-ion batteries (LIBs) are a leading energy storage technology, their energy densities are limited by the low capacity of conventional intercalation cathodes, driving interest in high energy-density Li–S batteries that make use of conversion chemistry. Achieving high capacity, reversibility, and cycle stability, and controlling volume changes in conversion batteries during the charge–discharge process, however, remains challenging. Here, in this study, we present a porous, amorphous, sulfide-based Mn x Mo 3 S 13 chalcogel, which concurrently offers high capacity and cycle stability. The solution-processable room temperature synthesized Mn x Mo 3 S 13 (x = 0.25) chalcogel exhibits a local structure that resembles the Mo 3 S 13 cluster with Mn 2+ distributed across the Mo 3 S 13 matrix, as determined by synchrotron X-ray pair distribution function (PDF) and extended X-ray absorption fine structure (EXAFS). Ab initio molecular dynamics (AIMD) simulations reveal that Mn 2+ incorporation shortens the polysulfide chain in the gel matrix compared to the Mo 3 S 13 chalcogel, while forming a coordination environment with disulfide groups, analogous to the experimental findings. A Li/Mn 0.25 Mo 3 S 13 half-cell delivers 897 mAh g –1 capacity during the first discharge and retains 571 mAh g –1 capacity after 100 cycles at a C/3 rate. Distribution of relaxation time (DRT) unveils a stable solid–electrolyte interphase (SEI) formation upon cycling that enables charge–discharge reversibility. Here, the enhanced capacity retention and cycle stability compared to those of the Li/Mo 3 S 13 cell are attributed to the reduced dissolution of active mass into the electrolyte, facilitated by the formation of shorter polysulfide chains within the Mn 0.25 Mo 3 S 13 structure and the strong affinity of Lewis-acidic Mn 2+ for polysulfide anions generated during the charge–discharge process of the Li/Mn 0.25 Mo 3 S 13 cell. Thus, this work illustrates a design principle of material for high-capacity and cycle-stable Li-metal sulfide batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

A Donor–Acceptor [2]Catenane for Visible Light Photocatalysis

Colored charge-transfer complexes can be formed by the association between electron-rich donor and electron-deficient acceptor molecules, bringing about the narrowing of HOMO–LUMO energy gaps so that they become capable of harnessing visible light. In an effort to facilitate the use of these widespread, but nonetheless weak, interactions for visible light photocatalysis, it is important to render the interactions strong and robust. Furthermore, we employ a well-known donor–acceptor [2]catenane—formed by the mechanical interlocking of cyclobis(paraquat-p-phenylene) and 1,5-dinaphtho[38]crown-10—in which the charge-transfer interactions between two 4,4'-bipyridinium and two 1,5-dioxynaphthalene units are enhanced by mechanical bonding, leading to increased absorption of visible light, even at low concentrations in solution. As a result, since this [2]catenane can generate persistent bipyridinium radical cations under continuous visible-light irradiation without the need for additional photosensitizers, it can display good catalytic activity in both photo-reductions and -oxidations, as demonstrated by hydrogen production—in the presence of platinum nanoparticles—and aerobic oxidation of organic sulfides, such as l-methionine, respectively. This research, which highlights the usefulness of nanoconfinement present in mechanically interlocked molecules for the reinforcement of weak interactions, can not only expand the potential of charge-transfer interactions in solar energy conversion and synthetic photocatalysis but also open up new possibilities for the development of active artificial molecular shuttles, switches, and machines.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Layered Nano-Mosaic of Niobium Disulfide Heterostructures by Direct Sulfidation of Niobium Carbide MXenes for Hydrogen Evolution

MXene-transition metal dichalcogenide (TMD) heterostructures are synthesized through a one-step heat treatment of Nb 2 C and Nb 4 C 3 . These MXenes are used without delamination or any pre-treatment. Heat treatments accomplish the sacrificial transformation of these MXenes into TMD (NbS 2 ) at 700 and 900 °C under H 2 S. This work investigates, for the first time, the role of starting MXene phase in the derivative morphology. It is shown that while treatment of Nb 2 C at 700 °C leads to the formation of pillar-like structures on the parent MXene, Nb 4 C 3 produces nano-mosaic layered NbS 2 . At 900 °C, both MXene phases, of the same transition metal, fully convert into nanomosaic layered NbS 2 preserving the parent MXene’s layered morphology. When tested as electrodes for hydrogen evolution reaction, Nb 4 C 3 -derived hybrids show better performance than Nb 2 C derivatives. The Nb 4 C 3 -derived heterostructure exhibits a low overpotential of 198 mV at 10 mA cm -2 and a Tafel slope of 122 mV dec -1 , with good cycling stability in an acidic electrolyte

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ageing of PBF‐Grade Poly(Phenylene Sulfide) Powder and its Effect on Critical Printability Properties

Abstract Poly(phenylene sulfide) (PPS) is a high‐performance polymer suiting the needs of powder bed fusion (PBF) early‐adopter industries. Although there are many benefits to PBF's powder bed‐based, one drawback is thermal ageing of the powder not incorporated into printed parts. Ideally, unfused powder can be reused in future builds; however, it is unlikely that critical printability properties of the thermally aged powder will remain unchanged. Changes in properties lead to either limited reuse through a practice of mixing used and new powder, or elimination of all powder after each build. In this paper, the authors report effects of thermal ageing in simulated printing conditions on properties of PPS critical to PBF processing. PBF‐grade PPS powder is exposed to process‐mimicking conditions. Properties relevant to the three PBF manufacturing process sub‐functions are assessed for the aged powders. Single‐layer prints are made using aged powder to observe polymer‐PBF interactions ad machina. Significant and systematic deviations from the as‐received state of the powder are observed for thermal and coalescence related properties with increasing exposure time and temperature. These changes are interpreted both in terms of physical and chemical changes in PPS and in terms of how these changes may impact the PBF printing process.

Chatham, Camden A.↗
DOE OSTI2020

Ultra-Low SWaP CO 2 Sensing for Demand Control Ventilation (Final Report)

In this project PARC and Energy ETC aimed to develop an ultra-low cost, size, weight, and power (SWaP) printed CO 2 sensor system for occupancy detection to enable Demand Control Ventilation (DCV) on a per-room basis. The CO 2 sensor technology is based on the temperature variation when CO 2 reversibly physisorbs to a highly conductive and high surface area sorbent surface, and is compatible with integration with PARC innovations in printed sensors and flexible electronics, for which PARC is a globally leading research center. The printed CO 2 sensor itself is designed to be compatible with PARC’s “peel-and-stick” platform of ultra-low power, low-cost, distributed sensors, and to facilitate real-time DCV based on overall indoor air quality (IAQ). Previously, PARC has developed flexible hybrid electronics (FHE) compatible materials to measure humidity, temperature, light, strain, and gases such as carbon monoxide, methane, ammonia, and hydrogen sulfide. Through this project, PARC developed FHE-compatible materials to measure CO 2 . Thus, with one <$15 FHE “peel-and-stick” based sensor node, a building management system (BMS) will be able to capture a complete picture of the indoor environment. This includes IAQ, light, temperature, and other comfort factors that impact building operations. Combined with optimized DCV, this low-cost sensor capability can be a key enabler of annual primary energy savings of ~ 0.3-0.4 Quad in commercial buildings while ensuring healthy IAQ. Energy ETC is a leader in supplier-agnostic BMS deployments and will design the commissioning and deployment procedures to maximize system interoperability.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Temperature-dependent growth of hexagonal and monoclinic gallium sulfide films by pulsed-laser deposition

We demonstrate the selective, pulsed-laser deposition of hexagonal GaS and monoclinic Ga2S3 films on sapphire substrates from a single Ga 2 S 3 target in high-vacuum conditions. Growth at substrate temperatures below 550 °C causes GaS film formation, which indicates non-stoichiometric transfer from the target to the film. Surprisingly, stoichiometric transfer occurs at substrate temperatures above 650 °C with monoclinic Ga 2 S 3 as the preferred, higher S-content phase. Through a series of growth and annealing experiments, we show that GaS nucleation under S-deficient conditions leads to the preferred growth of this layered, hexagonal phase below 550 °C. Furthermore, GaS films annealed above 650 °C under high vacuum are transformed to Ga 2 S 3 , reflecting the greater stability of the monoclinic phase. By first growing Ga 2 S 3 at a higher temperature and subsequently growing GaS at a lower temperature, we can fabricate GaS/Ga 2 S 3 heterostructures in a single growth process.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Novel Geochemistry Determined from High Pressure, High Temperature Simulation Experiments of Hydraulic Fracture Test Site 2

A standard method in unconventional oil and gas production is the process of hydraulic fracturing followed by a shut-in period, during which the fracture fluid remains pressurized in the reservoir for up to three weeks before production begins. Despite this widely used process, very little is known about what occurs in the reservoir during this shut-in process. In order to properly delineate potential reservoir reactions that may occur during shut-in that would lead to corrosion and scaling events, experiments were conducted in high pressure, high temperature reactors to simulate conditions of the Wolfcamp Formation in the Delaware Basin. Experimental design allowed the assessment of the effect of proppant, microbiology, and time on the mineralogy and fluid chemistry in the reservoir. Results suggest the biggest impact on fluid chemistry and shale mineralogy during shut-in is time. Analyses demonstrate dissolution of the shale material, with maximum dissolved ions occurring after 7 days of the shut-in period. After 21 days, results suggest precipitation occurs. The Delaware Basin is demonstrated to be high in sulfate content, which further increases in the fluid due to dissolution reactions during shut-in. The pressure vessel experiments suggest there was no significant contribution to reactions from microbiology during the shut-in period. Furthermore, early production samples demonstrate a significant selection of the microorganism Caminicella, a genus of which has previously been correlated to corrosion and sulfide production. Results suggest shut-in conditions may provide high sulfate concentrations that could later be utilized by a shifted microbial community to drive potential well infrastructure failure. This is the first study to incorporate microbiology, mineralogy, and fluid chemistry to investigate the fundamental geochemical reactions that occur during shut-in and early phase production of the Delaware Downloaded from http://onepetro.org/URTECONF/proceedings-pdf/21URTC/2-21URTC/D021S032R001/2477425/urtec-2021-5219-ms.pdf/1 by Carol Worster on 28 February 2022 Basin. Results from this study can complement observations from the Hydraulic Fracture Test Site 2 observations

58 GEOSCIENCES↗
DOE OSTI2024

Piezocatalytic ZnS:Mn 2+ Nanocrystals for Enhanced Organic Dye Degradation

Piezocatalysis, an emerging approach that harnesses mechanical energy to drive chemical reactions, has garnered significant attention due to its potential applications in diverse fields, particularly in environmental remediation. Its broader application, however, is often hindered by the low efficiency of existing piezocatalytic materials. Here, we report the synthesis of Mn 2+ -doped ZnS nanocrystals with improved piezoelectric properties using an emulsion-based colloidal assembly technique. Through well-controlled Mn 2+ doping, these nanocrystals demonstrate high piezocatalytic activity for degrading organic dyes under ultrasonic vibration. The optimal performance is achieved with 3% Mn 2+ doping, outperforming many existing piezocatalysts. Mechanistic studies reveal the generation of reactive oxygen species as the primary driving force for degradation. Notably, pre-excitation with UV light further boosts the piezocatalytic efficiency of these metal ion-doped ZnS nanocrystals by filling electron trap states, leading to improved overall performance. This research paves the way for developing high-performance piezocatalysts, expanding the potential of piezocatalysis for a wide range of applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Improved Performance of Cu(InGa)(SeS) 2 PV Modules Using the Reaction of Metal Precursors. Final Report

This project “Improved Performance of Cu(InGa)(SeS) 2 PV Modules using the Reaction of Metal Precursors” was a partnership led by the Institute of Energy Conversion (IEC) at the University of Delaware with Columbia University and the Molecular Foundry at the Lawrence Berkeley National Laboratory. The aim was to develop pathways to improve Cu(InGa)(SeS) 2 (CIGSS) thin film photovoltaic modules using processes compatible with low manufacturing cost. The CIGSS approach investigated was a two-step process including deposition of metal precursor films following by reaction in hydride gases utilizing IEC’s novel reactor. The process was similar to that under commercial development by the project’s industry partner Stion. When Stion went out of business mid-project the focus changed to a rapid thermal process considered more commercially viable. Approaches to improve the performance of solar cells using the reacted films focused on two material innovations. First, the overall Ga content was increased to increase the operating voltage, which is desirable for scale-up to commercial modules. Second, the processing and performance advantages arising from Ag alloying were investigated. Advanced characterization guided process and material development including control of relative composition gradients. Research on the formation of Cu-Ga-In metal precursors utilized sputtering deposition which is normally used in commercial applications. The work resulted in processes for deposition of precursor stacks with increased relative Ga content and effects of deposition parameters on morphology and phase composition were established. It was shown that the metal precursor films have comparable phase composition and morphology so subsequent reaction follows from the same starting point. The addition of Ag to the metal precursors gave more uniform morphology and improved adhesion of reacted films which enable higher reaction temperature for faster processing. A novel outcome was the discovery of a previously undocumented material phase in sputter-deposited and evaporated Ag-Cu-In-Ga thin films. Hydride gas reaction processes including time-temperature-concentration profiles were developed for different precursor compositions. This enables control of composition profiles to engineer through-film gradients for solar cell optimization with characterization and simulations used to correlate measured film composition profiles to measurements of devices. In particular, the gradient of sulfur at the front of the CIGSS film was found to be critical. The simulations guided process development leading to improved reproducibility of devices improved performance with higher Ga content and higher voltage. With Ag-alloyed precursors, the reaction pathways leading were determined. A significant finding was that Ag-alloying increases the reaction rate to completely convert precursor films to the final chalcopyrite which could enable reduced reaction time to benefit manufacturability. To maintain potential commercial viability, the process under investigation was refocused to a rapid thermal process that could potentially be incorporated into an in-line process for manufacturing. Precursors with different composition were capped with an extra selenium layer and reacted in hydrogen sulfide 5-15 minutes, compared to typically 2 hours in the previous multi-step batch process. Critical RTP parameters were identified to control the reaction. Further optimization would be needed for high efficiency solar cells but pathways to high quality devices with further optimization and improved heating uniformity were developed. The project also developed new optoelectronic characterization approaches with a focus on development and application of spatial- and time-resolved photoluminescence and a custom mapping photoluminescence microscope built. It was shown how critical electronic transport properties strongly depend on the chemical composition of the material and that a wide range of samples show inhomogeneity on a length scale larger than the grains in the films. Additionally, two-photon excitation capability was developed to distinguish bulk vs surface losses. The project advances the state-of-the -art for precursor reaction processes in several ways that could impact manufacturing. This includes validation of approaches to increase voltage and establishment of model-guided control to form optimal composition profiles. The application of process control approaches with knowledge of phase formation and reaction pathways can be critically valuable in designing a large-scale process.

14 SOLAR ENERGY↗
DOE OSTI2025

Fundamental Understanding of “Fresh” Lithium Nucleation and Growth in Sulfide-Based Anode-Free Solid-State Batteries: Effects of Substrate, Current Density, and Li + Supply

Understanding the electrochemical extraction and deposition of lithium (Li) from cathode is crucial for advancing anode-free solid-state batteries (AFSSBs). Herein, cryo-transmission electron microscopy (cryo-TEM) and electrochemical studies are employed to investigate how current collector surface properties, current densities, and cathode loadings influence the morphology of fresh electrochemically deposited Li and the electrochemical performance in sulfide-based AFSSBs. Cryo-TEM reveals that Cu current collectors induce irregular, dendritic Li deposits due to their lithiophobic nature and reactivity with Li 5.4 PS 4.4 Cl 1.6 (LPSC), while Ni and Au facilitate more uniform, planar-like Li growth. The morphology of the deposited Li also depends on current density: higher rates produce smaller, porous particles versus larger, denser deposits at lower rates. Importantly, for the first time, we discovered that low cathode loadings lead to poor cycling stability due to insufficient Li + supply for complete anode coverage, contrary to conventional solid-state batteries with preloaded Li metal anodes. This finding establishes a design principle where adequate cathode Li + reservoirs are essential for anode interface stability in AFSSBs. Overall, this work elucidates the interplayed effect of current collectors, current densities, and cathode loadings on Li morphology and cycle stability, offering fundamental insights into cathode-derived Li behavior and practical guidelines for optimizing AFSSBs performance through nucleation control and interface engineering.

25 ENERGY STORAGE↗
DOE OSTI2023

Predictive Engineering of Interfaces and Cathodes for High-Performance All Solid-State Lithium-Sulfur Batteries

The primary goal of this project is to leverage data-driven methods and machine learning strategies to develop accurate multi-physics models for all-solid-state Li-S battery (ASLSB) materials that can capture electrochemical and transport phenomena over atomic to mesoscopic length/timescales. These models will be rigorously validated by synthesis and advanced characterization experiments. The team will leverage the predictive power of these models, alongside synthesis/characterization experiments and battery fabrication to address longstanding issues at the electrode/electrolyte interfaces in ASLSBs. The project’s proposed technology involves the following: (1) halide-doped solid sulfide electrolytes that can concurrently provide high Li + ion conductivity and suppress dendrite growth; (2) novel mesoporous cathode composed of super-P and carbon nanotubes co-infiltrated with sulfur and sulfide electrolyte, which hold potential to allow high sulfur loading and optimal ion/electron pathways; and (3) functionalization of sulfide electrolyte with ionic liquids to improve physical contact and minimize impedance at the cathode/electrolyte interface. Successful development of proposed predictive models (at multiple scales) will bridge this knowledge gap and will advance fundamental understanding of reaction chemistry, kinetics, charge transfer, and dendrite growth at electrified SSIs. This will enable predictive design of effective strategies to mitigate interfacial problems in ASSLSBs, including poor interfacial contact, interfacial impedance to Li + ion transport, and poor electron/ion conduction within cathodes. Ultimately, the fundamental knowledge gained will lead to development of high-performance ASSLSBs.

25 ENERGY STORAGE↗
DOE OSTI2020

A dynamic microbial sulfur cycle in a serpentinizing continental ophiolite

Summary Serpentinization is the hydration and oxidation of ultramafic rock, which occurs as oceanic lithosphere is emplaced onto continental margins (ophiolites), and along the seafloor as faulting exposes this mantle‐derived material to circulating hydrothermal fluids. This process leads to distinctive fluid chemistries as molecular hydrogen (H 2 ) and hydroxyl ions (OH − ) are produced and reduced carbon compounds are mobilized. Serpentinizing ophiolites also serve as a vector to transport sulfur compounds from the seafloor onto the continents. We investigated hyperalkaline, sulfur‐rich, brackish groundwater in a serpentinizing continental ophiolite to elucidate the role of sulfur compounds in fuelling in situ microbial activities. Here we illustrate that key sulfur‐cycling taxa, including Dethiobacter , Desulfitispora and ‘ Desulforudis ’, persist throughout this extreme environment. Biologically catalysed redox reactions involving sulfate, sulfide and intermediate sulfur compounds are thermodynamically favourable in the groundwater, which indicates they may be vital to sustaining life in these characteristically oxidant‐ and energy‐limited systems. Furthermore, metagenomic and metatranscriptomic analyses reveal a complex network involving sulfate reduction, sulfide oxidation and thiosulfate reactions. Our findings highlight the importance of the complete inorganic sulfur cycle in serpentinizing fluids and suggest sulfur biogeochemistry provides a key link between terrestrial serpentinizing ecosystems and their submarine heritage.

Sabuda, Mary C.↗
DOE OSTI2020

Non-Equilibrium Synthesis of Highly Active Nanostructured, Oxygen-Incorporated Amorphous Molybdenum Sulfide HER Electrocatalyst

Molybdenum sulfide emerged as promising hydrogen evolution reaction (HER) electrocatalyst thanks to its high intrinsic activity, however its limited active sites exposure and low conductivity hamper its performance. To address these drawbacks, the non-equilibrium nature of pulsed laser deposition (PLD) is exploited to synthesize self-supported hierarchical nanoarchitectures by gas phase nucleation and sequential attachment of defective molybdenum sulfide clusters. Furthermore, the physics of the process are studied by in situ diagnostics and correlated to the properties of the resulting electrocatalyst. The as-synthesized architectures have a disordered nanocrystalline structure, with nanodomains of bent, defective S-Mo-S layers embedded in an amorphous matrix, with excess sulfur and segregated molybdenum particles. Oxygen incorporation in this structure fosters the creation of amorphous oxide/oxysulfide nanophases with high electrical conductivity, enabling fast electron transfer to the active sites. The combined effect of the nanocrystalline pristine structure and the surface oxidation enhances the performance leading to small overpotentials, very fast kinetics (35.1 mV dec -1 Tafel slope) and remarkable long-term stability for continuous operation up to -1 A cm -2 . This work shows possible new avenues in catalytic design arising from a non-equilibrium technique as PLD and the importance of structural and chemical control to improve the HER performance of MoS-based catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Selective Sorbent Design: CaS Aerogel for Rapid Remediation of Aqueous Pb (II)

Heavy metals are a persistent environmental problem due to their high toxicity, even at very low concentrations (parts per billion, ppb). The removal of such diluted heavy metals is challenging because of the competition the counterions (Ca 2+ , Na + , Mg 2+ , etc.) present in natural water bodies. The design of sorbents capable of removing ions below the action limit (15 ppb for Pb 2+ ) requires a strong driving force for selective uptake and rapid removal. In this work, we report the synthesis of porous CaS aerogels (surface area = 143.6 m 2 /g) by oxidative assembly of CaS nanoparticles and describe their use in selective Pb 2+ ion remediation from water. Despite the presence of amorphous CaCO 3 (up to 50 wt %) in the gel network, the gels demonstrated a capacity of 17.1 mmol Pb/g aerogel (3543 mg/g), and this could be augmented to 22.5 mmol Pb/g aerogel (4593 mg/g) by modifying the synthesis to reduce CaCO 3 content to ca. 15 wt %. Moreover, the selectivity of CaS aerogels toward Pb 2+ ions is high, as evidenced by little-to-no change in the distribution constant (K d ∼ 10 4 ) in the presence of competing ions (1 M) such as Na + , Mg 2+ , and Ca 2+ . During remediation with low concentrations (100 ppb) of Pb 2+ with CaS aerogels, the level of Pb 2+ dropped to 5.4 ppb (below the 15 ppb EPA limit) within 1 h with a 95.4% removal efficiency. In contrast to the CO 2 supercritically dried aerogels, lower surface area ambient dried gels (xerogels) only remove 40% of the lead ions from a 100 ppb solution, saturating within 1 h. The efficiency and rapidity of selective Pb 2+ uptake using CdS aerogels arise from a combination of a strong thermodynamic driving force for cation exchange (K eq = 2.5 × 10 27 ) and chemisorption along with favorable kinetics associated with the high surface area porous architecture. These results show that formation of high surface area metal chalcogenide aerogels by oxidative assembly to form nanocrystalline architectures, as previously demonstrated for II−VI and IV−VI semiconductors, can be extended to the more highly ionic alkaline earth sulfides.

Aerogels↗
DOE OSTI2025

Renewable diesel and bio-aromatics production from waste cooking oil using ethanol as a hydrogen donor in deoxygenation reaction

Biofuels offer a promising solution in the fight against climate change. With a global increase in waste cooking oil, this research investigated the production of bio-hydrogenated diesel (BHD) from waste cooking oil, using ethanol as a hydrogen donor in the deoxygenation process. A hydrolyzed waste cooking oil model compound served as the feedstock, and the deoxygenation was performed at 300–400 °C. The catalysts used in the experiments were 2.6 wt% Ni and 7.8 wt% Mo (2.6Ni-7.8Mo) and 10 wt% Ni and 5 wt% Mo (10Ni-5Mo) on γ-Al 2 O 3 . The results showed that ethanol is an effective hydrogen donor for biofuel production without the need for external hydrogen at an elevated pressure. The increasing temperature enhanced the free fatty acid (FFA) conversion and n-alkane selectivity in the oil product, with the highest FFA conversion and alkane selectivity of 100 % and 46 %, respectively, observed at 400 °C for the sulfided 10Ni-5Mo catalyst. On the other hand, 2.6Ni-7.8Mo offers 100 % FFA conversion with a lower n-alkane selectivity of 35 % at identical temperatures. The total acid number (TAN) of the oil products decreased from 174.03 mg KOH/g of feedstock to 9.43 and 8.67 mg KOH/g with the sulfided 2.6Ni-7.8Mo and 10Ni-5Mo catalysts, respectively. Both the catalysts achieved similar heating values (~43 MJ/kg) at 400 °C. This is a significant improvement to the HHV of the feedstock, which was 36.02 MJ/kg. Additionally, aromatic compounds, mainly BTXE (benzene, toluene, xylene, and ethylbenzene), were also produced. Compared to glycerol as a hydrogen donor, ethanol more effectively increased n-alkane selectivity due to its higher effective hydrogen-to-carbon ratio (H/C eff ). Conversely, glycerol was more advantageous for achieving greater selectivity towards BTXE compounds due to its lower H/C eff , which potentially leads to coke formation. Since aromatic compounds are intermediates in coke production, glycerol provides higher aromatic selectivity than ethanol. Finally, this study presents an alternative pathway for producing diesel fuel from waste cooking oil using ethanol as a hydrogen donor.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Pushing the Limits: Maximizing Energy Density in Silicon Sulfide Solid‐State Batteries

Here, for the first time, we demonstrate a silicon solid-state battery (SSB) architecture that achieves >400 Wh kg −1 , approaching the theoretical limit for silicon-based SSBs. This configuration features a 99.9 wt% micro-Si, a thin sulfide solid electrolyte (SSE), and a high-loading NMC811. Key to these results is strategically selecting and evaluating the processing techniques, whether wet or dry, for the negative electrode, positive electrode and thin sheet-type SSE. Excessive lithium incorporation into the silicon host, beyond the Li 3.75 +Si phase to form a LiSi composite, is essential to match the high capacity of the positive electrode. This SSB achieves over 1000 cycles for a 2 mAh cm −2 with ≈80% capacity retention and 94% capacity retention for 3 mAh cm −2 over 500 cycles at 25 °C. Post analysis identifies the primary capacity decay mechanisms as oxidation at the NMC/SSE interface and structural disruptions within NMC. Meanwhile, the Si electrode maintains a robust solid-electrolyte interphase layer, minimizing capacity decay. This study highlights the necessity for improved NMC coatings, lattice oxygen stabilization, and a durable positive electrode-electrolyte interface to improve the long-term stability of SSBs. Strategies leading to a single-layer pouch cell SSB exceeding 400 Wh kg −1 are developed.

25 ENERGY STORAGE↗
DOE OSTI2023

Interface Coating Design for Dynamic Voltage Stability of Solid‐State Batteries

Abstract Intrinsic or interface thermodynamic voltage windows of solid electrolytes are often narrower than the operational voltage range needed by a full battery, thus various interface decomposition reactions can happen in a practical solid‐state battery. Experimentally, it is found that a proper battery design utilizing the reactions can lead to a dynamic evolution from interface instability to stability, giving the so‐called dynamic voltage stability for advanced battery performance. Here, first the state‐of‐the‐art understanding is articulated about how the dynamic voltage stability should be interpreted in physical picture and treated in computation, emphasizing the potential importance of nonequilibrium reaction pathways. The constrained ensemble computational approach is further applied across most types of solid‐state electrolytes to systematically evaluate and compare their dynamic stability voltage windows in response to the mechanical constriction effect. High‐throughput calculations are used to search for coating materials for different interfaces between sulfide, halide, and oxide electrolytes and typical cathode materials with enhanced dynamic voltage stability. A comparison with experiment is given to highlight the value of these computational predictions.

Wang, Yichao↗