Results for “microstructure scale modeling” — Page 5

DOE OSTI2024

A Gaussian process autoregressive model capturing microstructure evolution paths in a Ni–Mo–Nb alloy

Additive manufacturing is increasingly being employed to produce components of complex geometries in structural alloys because of the expected energy savings associated with the near-net-shape capability and the ability to build in novel internal features that are not possible with many conventional manufacturing approaches. However, because of the extreme thermal conditions encountered, the non-equilibrium microstructures produced during powder bed-based additive manufacturing processes must be subjected to custom post-heat treatment processes to recover the target mechanical properties. Phase-field models and simulation techniques have matured to a state where the microstructure evolution paths, and the morphologies of the resulting precipitate phases can be predicted reasonably accurately, considering alloy-specific thermodynamic and kinetic aspects of the nucleation and growth processes. However, phase-field simulations are computationally intensive, which precludes the ability to apply the simulations directly to the length scale of the entire component. Therefore, it is highly desirable to develop low-computational-cost surrogate models that effectively capture the physics at the microstructural length scale, while facilitating the design of optimized processing conditions resulting in location-specific targeted microstructures at the component scale. The work presented here demonstrates the application of the materials knowledge system framework to develop a surrogate model that effectively captures the microstructural path during annealing of a Ni–Mo–Nb alloy containing different Mo and Nb compositions known to segregate during solidification under additive manufacturing conditions. Specifically, the surrogate model built in this work is based on a Gaussian process autoregressive model informed by statistical representation of simulated microstructures using two-point correlations and dimensionality reduction through principal component analysis. In conclusion, this surrogate model is shown to capture the bifurcation of the microstructural path during precipitation, which yields a microstructure dominated by the $\gamma^{\prime\prime}$ phase at high Nb concentrations and the $\delta$ phase at low Nb concentrations.

36 MATERIALS SCIENCE↗

DOE OSTI2025

A generalizable machine learning-assisted fast Fourier transform algorithm to simulate the large strain phenomena in polycrystalline materials

Machine learning methods have shown initial promise in constitutive modeling for single crystals or homogenized polycrystals, delivering notable computational efficiency. However, existing machine learning-based constitutive models often lack generalizability, limiting their application across diverse boundary value problems. This study introduces a thermodynamics-informed artificial neural network model to accelerate rate-tangent crystal plasticity fast Fourier transform simulations for cross-scale deformation behaviors of polycrystals under complex loading. Our model integrates microstructural variability and local interactions effectively. To address local effects in each grain, we employ K-means clustering to group Gauss points within the microstructure into clusters assumed to be in similar mechanical states. This approach, based on self-clustering analysis, extends model scope from macroscopic stress response to the granular level, capturing mechanical responses and orientation evolution across grains. This reduces the number of nonlinear problems to solve, with cluster responses propagated throughout each group. The thermodynamics-based artificial neural network-extracted features are further processed using local material state clusters to account for history-dependent deformation and evolving microstructures. Additionally, representative volume element simulations with rate-tangent crystal plasticity fast Fourier transform provide reliable datasets for model training. The proposed model demonstrates high efficiency, accuracy, self-consistency, and enhanced generalizability in predicting strain–stress responses and orientation evolution at both individual grain and aggregate scales under complex loading conditions, such as biaxial tension and arbitrary loading scenarios.

36 MATERIALS SCIENCE↗

DOE OSTI2022

The Challenges of Modeling Defect Behavior and Plasticity across Spatial and Temporal Scales: A Case Study of Metal Bilayer Impact

Atomistic molecular dynamics (MD) and a microstructural dislocation density-based crystalline plasticity (DCP) framework were used together across time scales varying from picoseconds to nanoseconds and length scales spanning from angstroms to micrometers to model a buried copper–nickel interface subjected to high strain rates. The nucleation and evolution of defects, such as dislocations and stacking faults, as well as large inelastic strain accumulations and wave-induced stress reflections were physically represented in both approaches. Both methods showed similar qualitative behavior, such as defects originating along the impactor edges, a dominance of Shockley partial dislocations, and non-continuous dislocation distributions across the buried interface. The favorable comparison between methods justifies assumptions used in both, to model phenomena, such as the nucleation and interactions of single defects and partials with reflected tensile waves, based on MD predictions, which are consistent with the evolution of perfect and partial dislocation densities as predicted by DCP. This substantiates how the nanoscale as modeled by MD is representative of microstructural behavior as modeled by DCP.

36 MATERIALS SCIENCE↗

DOE OSTI2020

An anisotropic viscoplasticity model for shale based on layered microstructure homogenization

Viscoplastic deformation of shale is frequently observed in many subsurface applications. Many studies have suggested that this viscoplastic behavior is anisotropic—specifically, transversely isotropic—and closely linked to the layered composite structure at the microscale. In this work, we develop a two-scale constitutive model for shale in which anisotropic viscoplastic behavior naturally emerges from semianalytical homogenization of a bilayer microstructure. The microstructure is modeled as a composite of soft layers, representing a ductile matrix formed by clay and organics, and hard layers, corresponding to a brittle matrix composed of stiff minerals. This layered microstructure renders the macroscopic behavior anisotropic, even when the individual layers are modeled with isotropic constitutive laws. Using a common correlation between clay and organic content and magnitude of creep, we apply a viscoplastic modified Cam-Clay plasticity model to the soft layers, while treating the hard layers as a linear elastic material to minimize the number of calibration parameters. We then describe the implementation of the proposed model in a standard material update subroutine. The model is validated with laboratory creep data on samples from three gas shale formations. We also demonstrate the computational behavior of the proposed model through simulation of time-dependent borehole closure in a shale formation with different bedding plane directions.

58 GEOSCIENCES↗

DOE OSTI2025

Fused Deposition Modeling Additive Manufacturing of Carbonized Structures via Waste-Enhanced Filaments

This report details the development, characterization, and use of coal-enhanced composite materials in additive manufacturing applications. High coal loading formulations—containing up to 70 wt.% coal—were successfully extruded and processed using commercially available 3D printers. Extensive experimental testing was conducted to assess the mechanical, thermal, and microstructural properties of the composites. In parallel, multi-scale computational modeling was employed to elucidate atomistic interactions and evaluate the effects of printing-induced defects on structural performance. Large-scale printability trials demonstrated the feasibility of fabricating complex components for tooling and construction applications, including wind turbine blade molds and modular wall sections. Techno-economic analyses demonstrated the cost-effectiveness and scalability of coal-enhanced composites for large-scale additive manufacturing applications such as wind turbine blade tooling.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2025

Micro-structural features and material properties impact on adhesive metal joints via computational modeling and machine learning

The quality of structural bonding in practical applications depends on various factors arising from materials, pre-processing conditions, and manufacturing. Understanding how these factors influence bonding performance and determining their relative importance are of significant interest. Thus, this study evaluates the effects of microstructural features and material properties on the structural strength of adhesively-bonded metal joints at the submillimeter scale, utilizing a combination of Finite Element Modeling (FEM) and Machine Learning (ML) with Gradient Boosting Regression (GBR). The microstructural features include adhesive thickness, internal voids within the adhesive, adherend-adhesive interfacial voids, void size and volume fraction, and surface roughness. The material properties include the constitutive behavior of the adhesive, as well as the adherend-adhesive interfacial strength and fracture energy. The changes in structural strength and morphologies of the bonded metal structures with respect to different microstructural features and material properties were clarified by FEM. By further leveraging ML-GBR, the sequence of importance of these factors affecting bonding performance across various scenarios was summarized. This work provides valuable insights into the development of improved structural bonding for adhesive joints in industries such as automotive , aerospace, and beyond.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Multiscale Thermal Conductivity Modeling of 3D Woven Composite Thermal Protection System Materials

Novel thermal protection systems (TPS) for re-entry and hypersonic vehicles utilize 3D woven composite materials with blended carbon filament tows (yarns) and a phenolic resin matrix. The presence of continuous carbon fibers provides superior stiffness and strength compared to legacy TPS, while the 3D weave pattern provides a great deal of design flexibility for both in-plane and through thickness thermomechanical behavior. However, modeling of 3D woven composites is notoriously complex and numerically intensive. The present investigation utilizes a unique ultra-efficient approach, known as Multiscale Recursive Micromechanics (MsRM), wherein recursive semi-analytical micromechanics methods are employed at various length scales within the composite. The MsRM approach has recently been extended to solve for the effective thermal conductivity as well as the local temperature and thermal flux fields throughout the composite. Presented model results focus on the impact of the microstructural geometry representation at each length scale on the material’s effective thermal conductivity, along with the local thermal flux and temperature fields induced in the microstructures, for a novel 3D woven TPS.

Composite↗

DOE OSTI2021

Microstructural-Level Fuel Performance Modeling of U-Mo Monolithic Fuel

As the physics that governs the microstructural evolution of nuclear fuel span various time and spatial scales, to fully understand the fuel behavior inevitably involves atomic to mesoscale resolution that can be difficult to determine experimentally. Microstructural-level modeling and simulations can be used to develop physics-based materials models that can provide physical understanding to inform fabrication process control, as well as a valuable feedback mechanism between post-irradiation examination (PIE) results and fabrication parameters. In accordance with the program schedule, the primary goals of the microstructure modeling effort are to: 1. Address critical microstructural questions and provide practical guidance to the fabricator via the fuel product specification; 2. Provide mechanistic inputs for the existing fuel performance code to improve its descriptive and predictive capability at the macroscopic scale. In fiscal year (FY)-21, the work scope consisted of six main facets: (1) the effect of carbides on fuel performance; (2) gas diffusivity in different phases; (3) integration of microstructural fuel performance modeling; (4) property degradation; (5) irradiation creep; and (6) historical analysis of microstructure data. Brief summaries of each are included below.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogeneities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogeneities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogeneities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogenities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2020

ICME and In-Situ Process Monitoring for Rapid Qualification of Components Made by Laser-based Powder Bed Additive Manufacturing Processes for Nuclear Structural Applications

Additive manufacturing (AM) through selective powder bed melting of successive layers is being considered as disruptive technology for rapid production of low-cost nuclear reactor internal components with complex geometries. However, there is a potential for non-uniform distribution of physical features, such as porosity or microstructural differences, due to variations of temperature across a component build. These heterogenities make the deployment of traditional material qualification and non-destructive evaluation of AM components difficult. This research project explored the feasibility of using in-situ process monitoring methods and integrated computational materials engineering (ICME) principles as an alternate qualification methodology and approach. This project included six individual tasks: (i) design of artifacts relevant to the nuclear power industry, (ii) evaluation of laser processing and in-situ measurements, (iii) computational modeling, (iv) ex-situ microstructural characterization, (v) evaluation of scaling the methodology for large-scale structures, and (vi) development of a data package to codes and standards organizations. As a part of this research, laser powder bed fusion of metals (316L, Alloy 718, and Ti6Al4V) was explored. This document provides an overview of the research performed over three years and serves as the final U.S. Department of Energy report for this project. In the third year, the project focused on the following activities: (a) in-situ infrared and optical imaging of each layer during processing of representative stainless steel geometries; (b) development of methodologies to analyze the data; and (c) application of ICME methodologies and other experiments to estimate the relevance of defects and microstructure to tensile properties.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2023

A data-driven framework for permeability prediction of natural porous rocks via microstructural characterization and pore-scale simulation

Understanding the microstructure–property relationships of porous media is of great practical significance, based on which macroscopic physical properties can be directly derived from measurable microstructural informatics. However, establishing reliable microstructure–property mappings in an explicit manner is difficult, due to the intricacy, stochasticity, and heterogeneity of porous microstructures. In this paper, a data-driven computational framework is presented to investigate the inherent microstructure–permeability linkage for natural porous rocks, where multiple techniques are integrated together, including microscopy imaging, stochastic reconstruction, microstructural characterization, pore-scale simulation, feature selection, and data-driven modeling. A large number of 3D digital rocks with a wide porosity range are acquired from microscopy imaging and stochastic reconstruction techniques. A broad variety of morphological descriptors are used to quantitatively characterize pore microstructures from different perspectives, and they compose the raw feature pool for feature selection. Here high-fidelity lattice Boltzmann simulations are conducted to resolve fluid flow passing through porous media, from which reliable permeability references are obtained. The optimal feature set that best represents permeability is identified through a performance-oriented feature selection process, upon which a cost-effective surrogate model is rapidly fitted to approximate the microstructure-permeability mapping via data-driven modeling. This surrogate model exhibits great advantages over empirical/analytical formulas in terms of prediction accuracy and generalization capacity, which can predict reliable permeability values spanning four orders of magnitude. Besides, feature selection also greatly enhances the interpretability of the data-driven prediction model, from which new insights into the mechanism of how microstructural characteristics determine intrinsic permeability are obtained.

58 GEOSCIENCES↗

NASA NTRS1989

Stereological characterization of dry alpine snow for microwave remote sensing

A persistent problem in investigations of electromagnetic properties of snow, from reflectance at visible wavelengths to emission and backscattering in the microwave, has been the proper characterization of the snow's physical properties. It is suggested that the granular and laminar structure of snow can be measured in its aggregated state by stereology performed on sections prepared from snow specimens, and that these kinds of measurements can be incorporated into models of the electromagnetic properties. With careful sampling, anisotropy in the snow microstructure at various scales can be quantified. It is shown how stereological parameters can be averaged over orientation and optical depth for radiative transfer modeling.

Davis, Robert E.↗

NASA NTRS2012

ISS-Experiments of Columnar-to-Equiaxed Transition in Solidification Processing

The main topic of the research project CETSOL in the framework of the Microgravity Application Promotion (MAP) programme of the European Space Agency (ESA) is the investigation of the transition from columnar to equiaxed grain growth during solidification. Microgravity environment allows for suppression of buoyancy-driven melt flow and for growth of equiaxed grains free of sedimentation and buoyancy effects. This contribution will present first experimental results obtained in microgravity using hypo-eutectic AlSi alloys in the Materials Science Laboratory (MSL) on-board the International Space Station (ISS). The analysis of the experiments confirms the existence of a columnar to equiaxed transition, especially in the refined alloy. Temperature evolution and grain structure analysis provide critical values for the position, the temperature gradient and the solidification velocity at the columnar to equiaxed transition. These data will be used to improve modeling of solidification microstructures and grain structure on different lengths scales.

Sturz, Laszlo↗

DOE OSTI2021

Identification of crystal plasticity model parameters by multi-objective optimization integrating microstructural evolution and mechanical data

Crystal plasticity models evolve a polycrystalline yield surface using meso-scale descriptions of deformation mechanisms. The activation of deformation mechanisms is governed by crystallography and a set of model parameters, which are typically calibrated through the fitting of mechanical data such as stress–strain curves and elastic lattice strains. Microstructural data such as phase fractions and texture evolution are used for verifying crystal plasticity parameters. In this study, we use a multi-objective genetic algorithm to identify hardening parameters from flow stress curves with an option to incorporate texture into the optimization approach. Robust, generalized objective functions are developed and used to identify sets of parameters pertaining to dislocation density-based hardening laws in visco-plastic and elasto-plastic self-consistent (VPSC and EPSC) homogenization models. First, the parameters are identified for pure Nb directly from texture using an objective function based on generalized spherical harmonics. Since texture evolution is driven by the relative contribution of active slip systems, the parameters governing the evolution of slip resistance ratios can be recovered from fitting discrete textures at a series of strains. Next, a comprehensive set of load reversal data for dual phase (DP) 780 steel is used to fit a hardening law and a back-stress law in EPSC. Finally, parameters pertaining to a complex hardening law for the evolution of slip and twinning in pure α-Ti are identified. Remarkably, using texture as an objective in combination with stress–strain objectives constrains the model of Ti to fully reproduce not only stress–strain and texture evolution but also hierarchical twinning measurements as a function of initial grain size and texture. Furthermore, given an appropriate model fit to representative experimental texture evolution, underlying twin volume fractions contributing to texture evolution can be predicted.

42 ENGINEERING↗

DOE OSTI2020

Multiscale-Informed Modeling of High Temperature Component Response with Uncertainty Quantification

This report summarizes a joint effort between Argonne National Laboratory, Idaho National Laboratory, and Los Alamos National Laboratory to develop and deploy constitutive models targeted at predicting the life of Grade 91 alloy components subjected to high temperature environments typical of those that structural components in advanced nuclear reactors would experience. Two distinct, but complementary constitutive modeling approaches have been taken here. The first employs a phenomenological viscoplastic model for which parameters have been calibrated based on experimental data for a wide range of Grade 91 alloy that has undergone a variety of processing. A Bayesian approach was used to derive distributions of uncertain parameters for this model based on this data set. The second approach is a reduced order model suitable for engineering-scale analysis that is based on the results of a large set of mesoscale simulations. Mesoscale models allow for the microstructure and composition of a particular alloy to be directly taken into account in the computation of the viscoplastic response, but are computationally expensive, which makes it impractical to directly call those models for the material constitutive response in an engineering-scale simulation. The reduced-order representation of the response of the underlying model used here allows for an engineering-scale model to take into account the characteristics of the underlying microstructure, while only incurring a reasonable computational expense. Both of these approaches have different strengths, and are applicable for different parts of the design/analysis process. The phenomenological models can be readily parameterized based on a set of experimental data for a given class of materials and used for scoping calculations. Once a specific material is chosen and adequately characterized, the reduced order models can accurately predict the response of that specific alloy, and because the models are based on predictive models of the underlying microstructure, they can be used to more confidently predict the response under conditions in regions where there is limited experimental data. Both of these models have been integrated in the Grizzly code, which is used here to perform proof-of-concept uncertainty quantification analyses of a simple component under prototypical conditions. The built- in stochastic analysis capabilities in the MOOSE framework that Grizzly is built on are used here to run large sets of simulations for this uncertainty quantification analysis. As would be expected, because the reduced order models are developed for a much more tightly defined alloy, they predict tighter distributions of the time to failure than the phenomenological models, which are calibrated to a broader set of data. Also important is that these simulations demonstrate that a reduced order modeling approach can be successfully deployed to propagate uncertainties from the material scale to practical engineering-scale component simulations.

42 ENGINEERING↗