Search NASA⌕ Search

SEARCH · Search NASA

Results for “spall”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Design of Planarizing Growth Conditions on Unpolished and Faceted (100)-Oriented GaAs Substrates Using Hydride Vapor Phase Epitaxy

Here we performed a design of experiments (DoE) analysis to determine the effect of various growth parameters on in situ planarizing overgrowth of rough substrates using hydride vapor phase epitaxy (HVPE). We used two types of rough (100)-oriented GaAs substrates to compare the effect of the initial morphology on the epitaxial growth behavior: an irregular, as-cut surface resultant from cutting the wafer from a GaAs boule and a regularly faceted surface produced by controlled spalling. The DoE analysis identified trends in the overgrowth behavior with changing growth conditions, and we used these trends to design favorable planarization growth conditions for each surface type. These favorable conditions enabled full planarization of a spalled surface with >2.5 um facet height within 10.8 min of growth. The root mean squared (RMS) surface roughness of the resulting (100) surface was 24.5 nm over a 286 um x 215 um area. Our results show that planarization growth by HVPE is a promising technique to enable device growth directly on rough substrates, and the trends revealed through DoE analysis indicate a path toward further optimization of planarization growth conditions for as-cut and spalled surfaces.

14 SOLAR ENERGY↗
DOE OSTI2022

Dynamic properties of 316l stainless steel repaired using electron beam additive manufacturing

Additive manufacturing has the potential to be used for repair of high-value parts, but the strength and integrity of such repaired parts, especially under dynamic loading, in still unknown. This work presents the results of high strain-rate dynamic testing of additively repaired stainless steel samples. The 316L samples were intentionally damaged and subsequently repaired with 308L stainless steel wire using electron beam additive manufacturing. The repaired samples were subjected to gas-gun impact testing to induce incipient damage and determine the role played by the repaired region in dictating damage and failure. The results show the following: 1) the equation of state of the repaired region is comparable to the original material as shown by the unchanged spall plane location, 2) the deformation behavior is similar to the original material as shown by the similar Hugoniot Elastic limit, 3) the spall strength of the repaired region is slightly higher than the original material due to varying grain size, and 4) the damage morphology in the repaired region is different and involves a high rate of void coalescence. In conclusion, despite these minor differences in the spall strength and the damage morphology, the overall dynamic response of the original material and repaired samples is similar suggesting that AM is a promising approach for repairing high-value components.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of moderate temperatures on compressive strength of ultra-high-performance concrete: A microstructural analysis

Highlights: • All coarse aggregates and steel fibres were surrounded by the binder. • X-ray diffraction is useful for explaining the increase in compressive strength with increasing temperature. • Rosenhahnite and/or quartz Dauphiné-twinned phases improved the compressive strength. • Polypropylene fibres prevented spalling and preserved the compressive strength. • Concrete with steel and polypropylene fibres did not exhibit spalling at 300 °C. Concrete with two types of steel fibres and a polypropylene fibre prevented spalling and preserved the compressive strength at 300 °C, which makes these concretes suitable for long-term applications up to 300 °C, such as for steam collectors or thermal energy storage systems. The compressive strength behaviour of three types of ultra-high-performance fibre-reinforced concrete manufactured with the same matrix was investigated. For this purpose, a complete characterisation of all the raw materials and the three types of fibres used was performed. The morphology of all concrete mixtures at room temperature was analysed using scanning electron microscopy–energy-dispersive X-ray spectroscopy. From the results, it was ascertained that the steel fibres and coarse siliceous aggregates were not in contact (being separated by ≥3.41 μm) and were surrounded by the binder (of ≥1 μm in thickness) for all the mixtures studied. Rosenhahnite and/or quartz Dauphiné-twinned phases improved the compressive strength (as determined by X-ray diffraction).

36 MATERIALS SCIENCE↗
DOE OSTI2021

The simulation of 3D hypervelocity spallation using a hydrocode PAGOSA with FLIP+MPM

n this work, a hydrocode PAGOSA with FLIP+MPM is presented and exercised to investigate the fracture in ductile material. The merit of PAGOSA with FLIP+MPM to solve the advection problem is first illustrated by a solid piston periodically moving in a sealed tube with air. Furthermore, the ability of PAGOSA with FLIP+MPM to capture the fracture in material is shown by a simple stretching fracture in ductile material. In both of two benchmark problems, the PAGOSA results and analytical solutions are also presented for comparison. Then PAGOSA with FLIP+MPM is used to model complex spall in ductile material, which is a challenging problem in engineering applications. The convergences of PAGOSA with FLIP+MPM—based on both the mesh size and the marker density—are investigated by monitoring free surface velocity. To further show the ability of PAGOSA with FLIP+MPM to predict fracture in ductile material, the numerical results are compared with the experimental results and other published numerical results. Moreover, the effect of the spall parameter in PAGOSA with FLIP+MPM on the numerical simulation is also analyzed by investigating the free surface velocity. Finally, the effects of the peak compressive stress, the tensile strain rate, and the loading rate on the spallation are further investigated. The numerical results show that PAGOSA with FLIP+MPM can improve PAGOSA's performance when applied to predicting fracture in ductile materials, and is robust enough to accurately predict spall fracture in ductile materials.

42 ENGINEERING↗
DOE OSTI2020

Hydrothermal Corrosion of First-Generation Dual-Purpose Coatings on Silicon Carbide for Accident-Tolerant Fuel Cladding

In this study, four different commercial coatings, TiN, Cr, CrN, and Cr/CrN (multilayer) were deposited by physical vapor deposition (PVD) on high resistivity chemical vapor deposited (CVD) SiC for the dual purpose of corrosion mitigation and fission gas hermeticity. The coatings were exposed for up to 2600 hours in flowing high temperature (288-350°C), high purity, liquid water with dissolved hydrogen (0.15-3ppm) or dissolved oxygen (1-2ppm). The Cr/CrN coatings did not adhere well and spalled quickly during exposure. In oxygenated conditions, none of the coatings were protective . CrN coatings spalled preferentially at defect sites, but reacted slowly enough in the absence of defects to potentially be chemically protective. TiN coatings fully oxidized within a few hundred hours and spalled. In hydrogen, all the coatings were chemically stable. Coating failures were identified and attributed to localized spallation, potentially related to coating defects. Coating improvements are recommended to reduce spallation and improve coating protection for future generations of dual-purpose coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Atomistic study of silicon alloying in the spallation behavior of nanocrystalline aluminum systems

Here, the effect of concentration of the alloying element silicon (Si) on the shock and spall response of aluminum (Al) is studied using classical molecular dynamics (MD) simulations. Silicon is distributed as individual grains and as grain boundaries and the dynamic response under shock is studied for an impact velocity of 1000 m/s. A general trend observed here is that the spallation is almost exclusively intergranular and limited to Al-Si interfaces. The spall strengths are observed to a) decrease with an increase in alloying of Si as grains and b) show little increase for up to 50% grain boundary segregation. An increase in grain size of the whole system showed negligible differences in spall strength, highlighting the significance of concentration of the alloying species rather than its grain size. These results provide an atomistic understanding of light-weight metallic systems under shock compression and pave the way for designing multiphase metal matrix alloys and composites for defense/armor applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Damage initiation and evolution in Al-Si layered microstructures under shock loading conditions at atomic scales

Designing materials with microstructural features like multiphase interfaces have shown significant promise for usage in the next generation defense and nuclear applications. The dynamic response of these interfaces in extreme environments is observed to vary with the deformability of individual phases, which could subsequently alter the favored damage nucleation sites related to spall failure. Here, we investigate the role of spacing of interfaces in a nanocrystalline layered Aluminum-Silicon system on the shock wave propagation behavior, and microstructural and defect evolution using classical molecular dynamics simulations. The simulations are carried out with different hypothetical Al/Si microstructures including variations in the distribution of Si grains as layers in a nanocrystalline Al matrix. The molecular dynamics simulations suggest that spall failure is preferentially initiated at Al/Si interfaces. In addition, for the same system volume and same concentration of Si, a higher number of layers is marked by an increase in shock wave velocity and reduced resistance to spall failure.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effect of macroscopic surface defects on dynamic damage: An experimental and numerical study

This study examines the impact of macroscopic surface defects on the dynamic ductile damage behavior of polycrystalline metals using plate-impact experiments. Defects of various shapes (flat, round, and point) were manufactured on the free or impact surfaces of annealed copper specimens. The experiments were diagnosed with photon Doppler velocimetry measurements and soft recovery techniques. The experimental results revealed that defect shape and location significantly affect velocity–time profiles and void distribution. In order to understand the dynamics of shock propagation and corresponding ductile damage evolution within the target specimens, the impact experiments were modeled with a calibrated Tepla model, a dynamic ductile damage model for polycrystalline metals [Nguyen et al., Int. J. Solids Struct. 329, 113833 (2026)]. Overall, our resulting simulated velocity showed good agreement with measured velocity, and our simulated porosity distributions qualitatively matched experimental data. Based on our simulation results, defects on the free surface were found to distort rarefaction waves and therefore the corresponding spall planes. On the other hand, defects on the impact surface generated a delayed shock when the flyer plate and the defected target area were in contact, leading to distortion of the spall plane. The distortion of the spall plane resulted in a non-uniform distribution of voids within the defected specimens. Lastly, we examined the role of local work hardening due to the defect manufacturing process on the velocity and porosity distribution, using Tepla simulations with a simplified representation of local hardening. This investigation highlights the importance of defect geometry, location, and local hardening associated with defect generation in dynamic ductile damage processes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Main Bearing Replacement and Damage - A Field Data Study on 15 Gigawatts of Wind Energy Capacity

This study seeks to establish a comprehensive baseline of knowledge for the replacement and damage of main bearings in wind turbines. The purpose of this report is to provide a high-level summary of the data set, methodology, and results of this work. Full technical details and an extended analysis will be made available in a future publication. We collected data on main bearing replacements and reported damage from industrial partners based in Europe and the United States. In total, we obtained data for 167 wind power plants, with a combined capacity of 15.3 gigawatts (GW). Most of the data set was comprised of land-based, three-point mount, spherical roller bearings. Within this data set were 689 instances of main bearing replacement. Analysis was undertaken in two parts: first, a statistical analysis of the main bearing time-to-replacement data using survival analysis techniques; second, quantitative and qualitative analyses of the obtained damage information. Our results showed that 10% of a fixed main bearing population would be expected to have been replaced by 10.5 years. This is close to half of the 20-year design value. Fitted parametric distributions then indicated that by year 20, between 22% and 25% of main bearings are expected to have been replaced. Analysis of the damage reports revealed spalling to be the main type of damage listed. The additional presence of surface damage in the collected data indicates that at least part of the spalling cases are likely due to surface-initiated rolling contact fatigue. At this stage is not clear what proportion of spalling cases result from "wear induced", surface-initiated and subsurface-initiated rolling contact fatigue. While this work provides important insights into the current state of main bearing replacements and damage, many questions remain. An ongoing and expanding data collection and analysis effort focused on wind turbine main bearings is therefore recommended.

17 WIND ENERGY↗
DOE OSTI2026

Towards the Ultimate Strength of Medium‐Entropy Alloys Through Pulsed Lasers

The tensile strength of metals at extreme strain rates is a key predictor of their performance in ballistic and structural impact applications. An important experimental method to reach these extreme strain rates is the use of high-amplitude, short-duration pulsed lasers. The Jupiter Laser Facility at the Lawrence Livermore National Laboratory enabled probing for the first time the mechanical response of several promising High Entropy Alloys at times on the order of nanoseconds (strain rates of ∼10 7 and ∼10 9 s −1 ). The measured strength is in the range of 6 to 10 GPa, ten times the quasistatic value. The mechanisms of plastic deformation and failure were identified and quantified through analysis and molecular dynamics simulation. The reflected wave amplitudes, obtained by VISAR, were used to determine the tensile (spall) stress. The high tensile strength obtained is due to two factors: the strain-rate dependence of plastic flow and the kinetics of void nucleation, growth, and coalescence. The experimental results are compared with an analytical prediction considering both grain-interior and grain-boundary void initiation. Molecular dynamics simulations, conducted at strain rates of 10 8 and 10 9 s −1 , rationalize the experimental results. In conclusion, they provide valuable information about the process of failure evolution, and reveal that grain boundary separation plays a pivotal role in spalling.

Materials science↗
DOE OSTI2023

Post-irradiation examination of the Sirius-1 nuclear thermal propulsion fuel test

Nuclear Thermal Propulsion (NTP) systems hold promise in reducing transit times for exploration of the solar system by both crewed and uncrewed missions. NTP systems currently under investigation include a once-through high-temperature gas-cooled fission reactor to provide thermal energy to heat the coolant, which also serves as the propellant. The fuel system consists of angular UN fuel particles dispersed in a matrix of W/Re, creating a ceramic and metallic composite or cermet, which has been irradiated in Idaho National Laboratory's (INL) Transient Reactor Test Facility (TREAT). This enabled evaluation of these materials under representative nuclear heating rates (~95 K/s) and peak surface temperatures (~2527 K). Further, these surface conditions were indicative of achievement of the target peak internal temperature of approximately 2850 K. These tests named Sirius-1 (UN–W/Re), have been irradiated and this paper will present post-irradiation examination results. The Sirius-1 test produced minor, stable cracks in the fuel specimen and spalling of surface material. Volatilized uranium ‘soot’ was found deposited on the inner wall of the irradiation capsule indicating loss of some fissile material from the fuel specimen. Spalling from the surfaces was also noted upon visual inspection. Uranium diffusion from the fuel particles resulted in the formation of U/Re phases and the production of a laminar microstructure on the edge of the fuel system. Overall, the specimen was stable and remained within a coolable geometry upon conclusion of multiple thermal cycles to prototypical operating temperatures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Particle size effects in metallic microparticle impact-bonding

In cold spray processing of metals, the critical velocity for particle bonding is dependent on both intrinsic material properties, such as density and (spall) strength, and extrinsic process parameters, such as the powder particle size. Here, we specifically isolate and investigate particle size effects on the critical velocity for bonding through laser- induced single particle impact experiments and finite element simulations. We also present a predictive framework to correlate particle size and critical velocity. We show that an increase in particle size leads to an increase in the temperature of the jet formed at the interface of the particle and the substrate. This increased temperature locally decreases the spall strength of the material which, in turn, decreases the critical velocity for larger particles.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic properties of FeCrMnNi, a high entropy alloy

The goal of this paper was to assess the dynamic properties of a new class of materials, High entropy alloys (HEAs). Specifically, gas gun experiments coupled with recovery were performed on a specific HEA, FeCrMnNi, to measure its equation of state (EOS) and its spall strength, which is a measure of the stress required to nucleate voids under shock loading conditions. While there has been a plethora of work performed to assess the mechanical properties of these HEAs under uniaxial stress conditions as a function of strain rate, investigation of its properties in dynamic extremes remains rare. The current work fills this gap in knowledge for this novel class of materials. Our results show that the measured EOS for this material at one velocity was in reasonable agreement with an estimated Hugoniot. Furthermore, while the spall strength for this material was found to be ~1.9 GPa, with some variation based on sample location, the main failure mode was brittle. This brittle failure leading to formation of cracks in the material is different than the ductile failure observed in pure iron and its alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dynamic response of additively manufactured Ti–5Al–5V–5Mo–3Cr as a function of heat treatment

Both shock and shockless compression experiments were performed on laser powder bed fusion (LPBF) Ti–5Al–5V–5Mo–3Cr (Ti-5553) to peak compressive stresses near 15 GPa. Experiments were performed on the as-built material, containing a purely β (body centered cubic) microstructure, and two differing heat treatments resulting in a dual phase α (hexagonal close packed) and β microstructure. The Hugoniot, Hugoniot elastic limit (HEL), and spallation strength were measured and compared to wrought Ti-6Al-4V (Ti-64). The results indicate the LPBF Ti-5553 Hugoniot response is similar between heat treatments and to Ti-64. The HEL stress observed in the LPBF Ti-5553 was considerably higher than Ti-64, with the as-built, fully β alloy exhibiting the largest values. The spallation strength of the LPBF Ti-5553 was also similar to Ti-64. Clear evidence of initial porosity serving as initiation sites for spallation damage was observed when comparing computed tomography measurements before and after loading. Post-mortem scanning electron microscopy images of the recovered spallation samples showed no evidence of retained phase changes near the spall plane. The spall plane was found to have kinks aligned with the loading direction near areas with large concentrations of twin-like, crystallographic defects in the as-built condition. For the heat-treated samples, the concentrations of twin-like, crystallographic defects were absent, and no preference for failure at the interface between the α and β phases was observed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Seismoacoustic analysis of underground explosions using the Rayleigh integral

SUMMARY A coupled seismoacoustic model is developed for the analysis of acoustic signals produced by underground explosive events with an aim to develop a means of improving estimated depth and yield for explosion monitoring. A ground spall model is used to predict surface motion characteristics produced by an underground explosion and the Rayleigh integral is applied to relate the surface motion to the acoustic signal some distance from surface ground zero. The low-frequency component of the ground motion associated with the prolonged free fall of lofted material during spall is found to dominate the acoustic signal propagating away from surface ground zero at shallow angles. The model is applied to observed ground motion and acoustic signals recorded during the Source Physics Experiment (SPE) with promising results. In addition to accurately predicting characteristics of the observed acoustic signals from several of the SPE events, the model provides a means of explaining the lack of signals observed during several events in the SPE due to the directionality of the higher frequency acoustic signals associated with the uplift and closure components as well as the lack of a spatially localized, longer duration dwell.

58 GEOSCIENCES↗
DOE OSTI2020

Dense Seismic Array Study of a Legacy Underground Nuclear Test at the Nevada National Security Site

The complex postdetonation geologic structures that form after an underground nuclear explosion are difficult to constrain because increased heterogeneity around the damage zone affects seismic waves that propagate through the explosion site. Generally, a vertical rubble-filled structure known as a chimney is formed after an underground nuclear explosion that is composed of debris that falls into the subsurface cavity generated by the explosion. Compared with chimneys that collapse fully, leaving a surface crater, partially collapsed chimneys can have remnant subsurface cavities left in place above collapsed rubble. The 1964 nuclear test HADDOCK, conducted at the Nevada test site (now the Nevada National Security Site), formed a partially collapsed chimney with no surface crater. Understanding the subsurface structure of these features has significant national security applications, such as aiding the study of suspected underground nuclear explosions under a treaty verification. In this study, we investigated the subsurface architecture of the HADDOCK legacy nuclear test using hybrid 2D–3D active source seismic reflection and refraction data. The seismic data were acquired using 275 survey shots from the Seismic Hammer (a 13,000 kg weight drop) and 65 survey shots from a smaller accelerated weight drop, both recorded by ~1000 three-component 5 Hz geophones. First-arrival, P-wave tomographic modeling shows a low-velocity anomaly at ~200 m depth, likely an air-filled cavity caused by partial collapse of the rock column into the temporary postdetonation cavity. A high-velocity anomaly between 20 and 60 m depth represents spall-related compaction of the shallow alluvium. Hints of low velocities are also present near the burial depth (~364 m). The reflection seismic data show a prominent subhorizontal reflector at ~300 m depth, a short-curved reflector at ~200 m, and a high-amplitude reflector at ~50 m depth. Comparisons of the reflection sections to synthetic data and borehole stratigraphy suggest that these features correspond to the alluvium–tuff contact, the partial collapse cavity, and the spalled layer, respectively.

58 GEOSCIENCES↗
DOE OSTI2020

Microstructural Changes to Thermally Sprayed Materials Subjected to Dynamic Compression

Dynamic compression of materials can induce a variety of microstructural changes. As thermally-sprayed materials have highly complex microstructures, the expected pressure at which changes occur cannot be predicted a priori. In addition, typical in-situ measurements such as velocimetry are unable to adequately diagnose microstructural changes such as failure or pore collapse. Quasi-isentropic compression experiments with sample recovery were conducted to examine microstructural changes in thermally sprayed tantalum and tantalum-niobium blends up to 8 GPa pressure. Spall fracture was observed in all tests, and post-shot pore volume decreased relative to the initial state. The blended material exhibited larger spall planes with fracture occurring at interphase boundaries. An estimate of the pressure at which pore collapse is complete was determined to be ~26 GPa for pure tantalum and ~19 GPa for the tantalumniobium blend under these loading conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Heat transfer through a box beam from an impinging hydrogen flame

An analysis was performed to determine whether a hydrogen jet flame impinging on a tunnel ceiling composed of multiple prestressed steel reinforced concrete box beams could result in permanent damage to the tunnel. The lower layer of the concrete box beam was modeled to determine whether heat reaches the steel reinforcing bars and whether spalling could occur. Heat transfer analysis shows that the temperature remains constant at the location of the steel reinforcing bars after 1.3 minutes of impingement and reaches a maximum of 130°C after 5 minutes. However, assuming a constant impingement for 5 minutes is an over estimation due the existing fire model which includes conservative assumptions. Explosive spalling may occur at a thin layer (~0.05 in. at 50 seconds, 0.1 in. at 5 minutes) at the bottom surface of the concrete box beam, but the steel reinforcing bars will not be exposed to the hydrogen flame.

42 ENGINEERING↗