Search NASA⌕ Search

SEARCH · Search NASA

Results for “WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Weld-brazing of titanium

A joining process, designated weld-brazing, which combines resistance spot-welding and brazing has been developed at the NASA Langley Research Center. Resistance spot-welding is employed to position and aline the parts and to establish a suitable faying surface gap for brazing and contributes to the integrity of the joint. Brazing enhances the properties of the joint and reduces the stress concentrations normally associated with spotwelds. Ti-6Al-4V titanium alloy joints have been fabricated using 3003 aluminum braze both in a vaccum furnace and in a retort containing an inert gas environment.

Bales, T. T.↗
NASA NTRS1973

Combined effects of weld-induced residual stresses and flaws on the fracture strength of Ti-5Al-2.5Sn

The combined effects of weld-induced residual stresses and flaws on fracture strength were experimentally evaluated by testing Ti-5Al-2.5Sn surface flawed specimens at -320F (-195C) in liquid nitrogen. Flaws were located in weld metal with crack planes either parallel to or perpendicular to gas tungsten arc weld centerlines, and in base metal with the crack plane perpendicular to the rolling direction. Tests were conducted using two different flaw sizes to effect fracture stresses at two different levels including one level either at or near, and one level well below the tensile yield strength. Three different residual stress levels were generated, measured, and tested. Results were evaluated using modified linear elastic fracture mechanics theory.

Hall, L. R.↗
NASA NTRS1974

Solar array welding developement

The present work describes parallel gap welding as used for joining solar cells to the cell interconnect system. Sample preparation, weldable cell parameter evaluation, bond scheduling, bond strength evaluation, and bonding and thermal shock tests are described. A range of weld schedule parameters - voltage, time, and force - can be identified for various cell/interconnect designs that will provide adequate bond strengths and acceptably small electrical degradation. Automation of solar array welding operations to a significant degree has been achieved in Europe and will be receiving increased attention in the U.S. to reduce solar array fabrication costs.

Elms, R. V., Jr.↗
NASA NTRS1976

Fracture mechanics for weld acceptance

Criteria include specifications for allowable cracklike defect lengths, undercut, underfill, suckback, mismatch, peaking in butt welds, root penetration, weld beam dimensions, lap joint dimensions, and acceptable defect sizes and densities for double and single fillet welds.

Bolstad, C. A.↗
NASA NTRS1975

Welding and joining: A compilation

A compilation is presented of NASA-developed technology in welding and joining. Topics discussed include welding equipment, techniques in welding, general bonding, joining techniques, and clamps and holding fixtures.

Source record↗
NASA NTRS1974

Analysis of thermal stresses and metal movement during welding

Finite element computer programs were developed to determine thermal stresses and metal movement during butt welding of flat plates and bead-on-plate welding along the girth of a cylindrical shell. Circular cylindrical shells of 6061 aluminum alloy were used for the tests. Measurements were made of changes in temperature and thermal strains during the welding process.

Muraki, T.↗
NASA NTRS1976

Capillary flow weld-bonding

The invention of a weld-bonding technique for titanium plates was described. This involves fastening at least two plates of titanium together using spot-welding and applying a bead of adhesive along the edge of the resistance spot-welded joint which upon heating, flows and fills the separation between the joint components.

Vaughan, R. W.↗
NASA NTRS1976

Development of explosive welding procedures to fabricate channeled nozzle structures

Research was conducted to demonstrate the feasibility of fabricating a large contoured structure with complex internal channeling by explosive welding procedures. Structures or nozzles of this nature for wind tunnel applications were designed. Such nozzles vary widely in their complexity. However, in their simplest form, they consist of a grooved base section to which a cover sheet is attached to form a series of internal cooling passages. The cover sheet attachment can be accomplished in various ways: fusion welding, brazing, and diffusion welding. The cover sheet has also been electroformed in place. Of these fabrication methods, brazing has proved most successful in producing nozzles with complex contoured surfaces and a multiplicity of internal channels.

Pattee, H. E.↗
NASA NTRS1978

Technology of welding aluminum alloys-I

Systems approach to high-quality aluminum welding uses square-butt joints, kept away from sharp contour changes. Intersecting welds are configured for T-type intersections rather than crossovers. Differences in panel thickness are accommodated with transition step areas where thickness increases or decreases within weld, but never at intersection.

Harrison, J. R.↗
NASA NTRS1978

Technology of welding aluminum alloys-III

Control of porosity in weld beads was major objective in development of aluminum welding program. Porosity, most difficult defect to control, is caused by hydrogen gas unable to escape during solidification. Hard tooling allows hotter bead than free-fall tooling so hydrogen bubbles can boil out instead of forming pores. Welding position, moisture, and cleanliness are other important factors in control of porosity.

Harrison, J. R.↗
NASA NTRS1976

Weld-bonded titanium structures

Structurally stronger titanium articles are produced by a weld-bonding technique comprising fastening at least two plates of titanium together using spotwelding and curing an adhesive interspersed between the spot-weld nuggets. This weld-bonding may be employed to form lap joints or to stiffen titanium metal plates.

Vaughan, R. W.↗
NASA NTRS1977

Diffusion welding of a directionally solidified gamma/gamma prime - delta eutectic alloy

Hot-press diffusion welding parameters were developed for a directionally solidified, gamma/gamma prime-delta eutectic alloy. Based on metallography, a good diffusion weld was achieved at 1100 C under 34.5 MPa (5 ksi) pressure for 1 hour. In addition, a dissimilar metal weld between gamma/gamma prime-delta and IN-100 was successfully made at 1100 C under 20.7 MPa (3 ksi) pressure for 1 hour.

Moore, T. J.↗
NASA NTRS1979

Reducing weld peaking in aluminum

Excessive weld peaking can be corrected in heavy aluminum structures according to procedure. When peaking varies along weld joint, weld energy must be varied to compensate for nonuniformity.

Bayless, E.↗
NASA NTRS1978

Nine percent nickel steel heavy forging weld repair study

The feasibility of making weld repairs on heavy section 9% nickel steel forgings such as those being manufactured for the National Transonic Facility fan disk and fan drive shaft components was evaluated. Results indicate that 9% nickel steel in heavy forgings has very good weldability characteristics for the particular weld rod and weld procedures used. A comparison of data for known similar work is included.

Young, C. P., Jr.↗
NASA NTRS1980

Shear strength of aluminum fillet welds

Shear-strength tests on aluminum fillet welds are documented in report. Test were made on aluminum alloy 2219 to aid designers in specifying sizes and lengths of fillet welds necessary to sustain expected loads in this material. Report discusses fillet-weld size and geometry, including root penetration and surface contour.

Lovoy, C. V.↗
NASA NTRS1980

Viewing electron-beam welds in progress

With aid of optical filter, operator of electron-beam welding machine can view TV image of joint that is being welded and can make corrections as necessary. Operator can see when weld bead gets out of alinement, for example, and compensate for deflection of electron beam caused by changes in magnetic field.

Armenoff, C. T.↗
NASA NTRS1980

Welding multiple plies with an electron beam

Method for electron-beam welding of multi-ply metal sheets eliminates ply separation and minimizes porosity. Method was developed for assembling bellows made of four plies of iron/nickel alloy sheets. Method consists of making successive stitch welds with electron beam until weld seam is completely filled in and all plies have been penetrated.

Kiluk, F. J.↗
NASA NTRS1980

Ion-beam cleaning for cold welds

1000 eV beam bombarding metal surfaces to be joined removes oxides and contaminants at rate of several atomic layers per second for current density of 1 mA/squ. cm. Clean surfaces can then be joined by squeezing them together. With ion-beam cleaning, mating force for strong bond is low enough to cause only 1% deformation. Conventional cold-welding requires about 70% deformation for bonding. Technique was tested successfully on aluminum to aluminum welds, copper to copper, copper to aluminum, copper to nickel, and silver to iron. Base metals failed before welds in tear test.

Slater, B. L.↗