Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETIC SWITCHING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Solar Activity Studies using Microwave Imaging Observations

We report on the status of solar cycle 24 based on polar prominence eruptions (PEs) and microwave brightness enhancement (MBE) information obtained by the Nobeyama radioheliograph. The north polar region of the Sun had near-zero field strength for more than three years (2012-2015) and ended only in September 2015 as indicated by the presence of polar PEs and the lack of MBE. The zero-polar-field condition in the south started only around 2013, but it ended by June 2014. Thus the asymmetry in the times of polarity reversal switched between cycle 23 and 24. The polar MBE is a good proxy for the polar magnetic field strength as indicated by the high degree of correlation between the two. The cross-correlation between the high- and low-latitude MBEs is significant for a lag of approximately 5.5 to 7.3 years, suggesting that the polar field of one cycle indicates the sunspot number of the next cycle in agreement with the Babcock-Leighton mechanism of solar cycles. The extended period of near-zero field in the north-polar region should result in a weak and delayed sunspot activity in the northern hemisphere in cycle 25.

microwave radio emission↗
DOE OSTI2021

New Modulation and Impact of Transformer Leakage Inductance on Current-Source Solid-State Transformer

This article presents a novel modulation scheme for device voltage stress mitigation and comprehensive analysis of the impact of transformer leakage inductance in a current-source solid-state transformer (SST). Different from dual active bridge (DAB) SST, the operation of the current-source SST is similar to that of a flyback converter. The device bridge on only one side of the transformer is active to store energy into or release energy from the magnetizing inductance which acts as a current-source dc link. Such flyback operation with reverse-blocking switches can lead to additional device voltage stress and incomplete zero-voltage switching (ZVS) on the current-source soft-switching solid-state transformer (S4T) under conventional modulation. A new modulation scheme is proposed to address this issue. Moreover, different from the DAB, the leakage inductance of the medium-frequency transformer (MFT) in the S4T is a parasitic element similar to that in a matrix SST and can cause additional device voltage stress. Though the resonant capacitors, originally added to achieve ZVS, can absorb and recycle the leakage energy in the S4T, these capacitors need to be increased with larger leakage inductances to limit the voltage stress. However, large resonant capacitors can result in more lost duty cycles and reduced efficiency. The impact of such leakage inductance on device voltage stress is analyzed comprehensively, which is critical to guide future research and design of the S4T. Experimental results from S4T prototypes for DC-DC, multiport AC-DC, and AC-AC conversion with 1:1 and 4:1 MFT comprehensively verify the proposed concepts. Lastly, a case study of a three-phase AC-AC S4T over a power range from 1 kVA to 100 kVA each module reveals that the MFT leakage inductance should be less than 1% of the magnetizing inductance for safe operation.

14 SOLAR ENERGY↗
DOE OSTI2017

Chitosan-Gated Magnetic-Responsive Nanocarrier for Dual-Modal Optical Imaging, Switchable Drug Release, and Synergistic Therapy

In this study, we present a multifunctional yet structurally simple nanocarrier that has a high drug loading capacity, releases drug in response to onset of an AC magnetic field, and can serve as a long-term imaging contrast agent and effectively kills cancer cells by synergistic action. This nanocarrier (HMMC-NC) has a spherical shell structure with a center cavity of 80 nm in diameter. The shell is comprised of two layers: an inner layer of magnetite that exhibits superparamagnetism and an outer layer of mesoporous carbon embedded with carbon dots that exhibit photoluminescence property. Thus in addition to being a drug carrier, HMMC-NC is also a contrast agent for bioimaging. The switchable drug release is enabled by the chitosan molecules attached on the nanocarrier as the switching material which turns on or off the drug release in response to the application or withdrawal of an AC magnetic field.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Wet chemistry-synthesized Fe/mixed ferrite soft magnetic composites for high-frequency power conversion

State-of-the-art soft magnetic (SM) alloy systems such as electrical steels and permalloys exhibit large eddy current losses at high-frequency (kHz range and above), limiting their application in fast switching devices. Eddy current losses can be reduced for metallic alloys through a decrease in characteristic length scale or embedding them in an insulation layer. This work proposes the development of fine-scale core materials consisting of metallic SM nano/microparticles with magnetic, inorganic insulation layers, and their synthesis using a wet chemistry-based, scalable method for high frequency and high-power applications. More specifically, a magnetic ferrite coating (Ni 0.5-x Mn x Zn 0.5 Fe 2 O 4 , x = 0.0–0.5) was applied via deposition of ferrite powder produced using a “wet chemistry-based” co-precipitation method; the ferrite was distributed through the Fe micropowder via either ball milling or ultrasonic mixing. Powder cores were prepared by compaction of the synthesized composites. Relative magnetic permeability and core loss were measured at excitation frequencies to 200 kHz. A core loss of 127 kW/m 3 was measured at excitation frequency of 100 kHz and magnetization of 0.02 T. This value improves on the 199.3 kW/m 3 reported in literature at identical excitation conditions for a compact formed from a composite comprising Fe microparticles coated with low-permeability Ni 0.5 Zn 0.5 Fe 2 O 4 . Ultrasonic mixing resulted in slightly lower core loss than ball milling, possibly because ball milling causes loss-increasing deformation of the Fe micropowder. XRD and SEM were used to observe composite composition and core cross-section microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Two-Step Control Approach for Torque Ripple and Vibration Reduction in Switched Reluctance Motor Drives

The objective of this work is to reduce the torque ripple and vibration in Switched Reluctance Motor (SRM) drives. To achieve such a goal, a two-step approach is proposed. In the first step, the reference current is profiled using an optimization method, aimed to reduce the torque pulsation. In the second, the optimum current profile is applied to the SRM through an adaptive hysteresis band controller to actively cancel the radial vibration. The proposed technique uses an optimization procedure based on the Field Reconstruction Method (FRM) and Non-Derivative Optimization Method to find the optimal current profile that mitigates the torque pulsation, however, the investigation has shown that the proposed excitation leads to a higher radial vibration, which has been mitigated by using an adaptive hysteresis band controller. The theoretical basis for the proposed approach is initially presented, followed by system modeling and simulation. In addition, experimental verification has been conducted using an 8/6 SRM to show the feasibility of the proposed approach. The proposed method alleviates the acoustic noise and torque pulsation in SRM and offers an effective step towards the prevalent use of SRM in a wide range of applications.

42 ENGINEERING↗
DOE OSTI2017

Fast piezoelectric valve offering controlled gas injection in magnetically confined fusion plasmas for diagnostic and fuelling purposes

In magnetically confined fusion plasmas controlled gas injection is crucial for plasma fuelling as well as for various diagnostic applications such as active spectroscopy. In this paper, we present a new, versatile system for the injection of collimated thermal gas beams into a vacuum chamber. This system consists of a gas pressure chamber, sealed by a custom made piezo valve towards a small capillary for gas injection. The setup can directly be placed inside of the vacuum chamber of fusion devices as it is small and immune against high magnetic fields. This enables gas injection close to the plasma periphery with high duty cycles and fast switch on/off times ≲ 0.5 ms. In this work, we present the design details of this new injection system and a systematic characterization of the beam properties as well as the gas flowrates which can be accomplished. The thin and relatively short capillary yields a small divergence of the injected beam with a half opening angle of 20°. The gas box is designed for pre-fill pressures of 10 mbar up to 100 bars and makes a flowrate accessible from 10 18 part/s up to 10 23 part/s. It hence is a versatile system for both diagnostic as well as fuelling applications. Finally, the implementation of this system in ASDEX Upgrade will be described and its application for line ratio spectroscopy on helium will be demonstrated on a selected example.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1970

A transformer of closely spaced pulsed waveforms

Passive circuit, using diodes, transistors, and magnetic cores, transforms the voltage of repetitive positive or negative pulses. It combines a pulse transformer with switching devices to effect a resonant flux reset and can transform various pulsed waveforms that have a nonzero average value and are relatively cosely spaced in time.

Niedra, J.↗
NASA NTRS1995

Observation of a slow-mode shock in the dayside magnetopause reconnection layer

Plasma and magnetic field data from the International Sun Earth Explorer (ISEE) 2 spacecraft recorded on 29 Oct 1979 provide evidence for a slow shock (SS) in the reconnection layer of the dayside magnetopause. This layer is bounded on the magnetosheath side by the SS and on the magnetospheric side by a rotational discontinuity (RD). The direction of the accelerated plasma flow, the earthward sense of the normal magnetic field across both discontinuities, and the relative orientation of the SS and the RD all indicate that the reconnection site was located south of the spacecraft. Examination of the substantial pressure anisotropy downstream of the SS explains two unusual properties of the shock: (1) the slow-mode and intermediate-mode phase speeds are inverted downstream of the SS such that the RD propagates behind the SS rather than ahead of it; (2) the magnetic wave polarization reserves such that the SS initially displays a left-handed polarization and then switches to a right-handed polarization inside the shock structure.

Walthour, D. W.↗
NASA NTRS2002

Performance of High-frequency High-flux Magnetic Cores at Cryogenic Temperatures

Three magnetic powder cores and one ferrite core, which are commonly used in inductor and transformer design for switch mode power supplies, were selected for investigation at cryogenic temperatures. The powder cores are Molypermalloy Core (MPC), High Flux Core (HFC), and Kool Mu Core (KMC). The performance of four inductors utilizing these cores has been evaluated as a function of temperature from 20 C to -180 C. All cores were wound with the same wire type and gauge to obtain equal values of inductance at room temperature. Each inductor was evaluated in terms of its inductance, quality (Q) factor, resistance, and dynamic hysteresis characteristics (B-H loop) as a function of temperature and frequency. Both sinusoidal and square wave excitations were used in these investigations. Measured data obtained on the inductance showed that both the MPC and the HFC cores maintain a constant inductance value, whereas with the KMC and ferrite core hold a steady value in inductance with frequency but decrease as temperature is decreased. All cores exhibited dependency, with varying degrees, in their quality factor and resistance on test frequency and temperature. Except for the ferrite, all cores exhibited good stability in the investigated properties with temperature as well as frequency. Details of the experimental procedures and test results are presented and discussed in the paper.

Gerber, Scott S.↗
NASA NTRS2004

Advanced Power Electronics Components

This paper will give a description and status of the Advanced Power Electronics Materials and Components Technology program being conducted by the NASA Glenn Research Center for future aerospace power applications. The focus of this research program is on the following: 1) New and/or significantly improved dielectric materials for the development of power capacitors with increased volumetric efficiency, energy density, and operating temperature. Materials being investigated include nanocrystalline and composite ceramic dielectrics and diamond-like carbon films; 2) New and/or significantly improved high frequency, high temperature, low loss soft magnetic materials for the development of transformers/inductors with increased power/energy density, electrical efficiency, and operating temperature. Materials being investigated include nanocrystalline and nanocomposite soft magnetic materials; 3) Packaged high temperature, high power density, high voltage, and low loss SiC diodes and switches. Development of high quality 4H- and 6H- SiC atomically smooth substrates to significantly improve device performance is a major emphasis of the SiC materials program; 4) Demonstration of high temperature (> 200 C) circuits using the components developed above.

Schwarze, Gene E.↗
DOE OSTI2019

Effect of Substrate Temperature on Structural, Morphological, Magnetic, and Electrical Properties of Fe{sub 2}CoSi Heusler Alloy Thin Films for Spin-Based Device Applications

Fe{sub 2}CoSi based Heusler alloy thin films are deposited on single crystal Si (111) substrate at different substrate temperatures varying from room temperature to 600 °C using ultrahigh vacuum DC magnetron sputtering. Structural analysis of the prepared thin films is carried out using GI-XRD measurement and it conform ordered L2{sub 1} crystal structure of the films deposited at 450 °C and above. The atomic force microscopic (AFM) images of Fe{sub 2}CoSi thin films exhibiting 3D-like growth on Si (111) substrate at varying temperatures. The magnetic property of the thin films is studied using vibrating sample magnetometer (VSM). At 450 °C of substrate temperature, the prepared thin film exhibits high saturation magnetization (M{sub s} = 948 emu/cc) and low coercivity (H{sub c} = 8 Oe). The self-energy magnetization of the film and its own field is very high, when the temperature of the substrate was maintained at 450 °C and switching field ratio for this film was obtained as ~ 0.9 due to its high crystallinity and atomic ordering. The electrical property of Fe{sub 2}CoSi thin film is investigated using four-probe technique and a positive magnetoresistive behavior was observed for thin film deposited at a substrate temperature of 450 °C which indicates the possible half-metallic nature at room temperature. The enhanced magnetic and electrical properties obtained for the thin film prepared at 450 °C substrate temperature is highly suitable for spin based device applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

All-optical switching of localized surface plasmon resonance in single gold nanosandwich using GeSbTe film as an active medium

Localized surface plasmon resonance (LSPR) switching was investigated in a Au/GeSbTe/Au nanosandwich as a key active element for plasmonic integrated circuits and devices. Near-infrared single-particle spectroscopy was conducted to examine the interaction of a Au nanorod (AuNR) and Au film, between which a GeSbTe layer was incorporated as an active phase-change media. Numerical calculation revealed that hybridized modes of the AuNR and Au film exhibit a significant change of scattering intensity with the phase change. In particular, the antisymmetric (magnetic resonance) mode can be modulated effectively by the extinction coefficient of GST, as well as its refractive index. Experimental demonstration of the switching operation was performed by alternate irradiation with a picosecond pulsed laser for amorphization and a continuous wave laser for crystallization. Repeatable modulation was obtained by monitoring the scattering light around the LSPR peak at λ = 1070 nm.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-temperature quantum valley Hall effect with quantized resistance and a topological switch

Edge states of a topological insulator can be used to explore fundamental science emerging at the interface of low dimensionality and topology. Achieving a robust conductance quantization, however, has proven challenging for helical edge states. In this work, we show wide resistance plateaus in kink states—a manifestation of the quantum valley Hall effect in Bernal bilayer graphene—quantized to the predicted value at zero magnetic field. The plateau resistance has a very weak temperature dependence up to 50 kelvin and is flat within a dc bias window of tens of millivolts. We demonstrate the electrical operation of a topology-controlled switch with an on/off ratio of 200. These results demonstrate the robustness and tunability of the kink states and its promise in constructing electron quantum optics devices.

Science & Technology - Other Topics↗
DOE OSTI2015

Temperature effect on vortex-core reversals in magnetic nanodots

We studied the temperature effect on vortex-core reversals in soft magnetic nanodots by micromagnetic numerical calculations within a framework of the stochastic Landau-Lifshitz-Gilbert scheme. It was determined that vortex-core-switching events at non-zero temperatures occur stochastically, and that the threshold field strength increases with temperature for a given field frequency. The mechanism of core reversals at elevated temperatures is the same as that of vortex-antivortex-pair-mediated core reversals found at the zero temperature. The reversal criterion is also the out-of-plane component of a magnetization dip that should reach −p, which is to say, m{sub z,dip} = −p, where p is the original polarization, p = +1 (−1), for the upward (downward) core. By this criterion, the creation of a vortex-antivortex pair accompanies complete vortex-antivortex-annihilation-mediated core reversals, resulting in the maximum excess of the exchange energy density, ΔE{sub ex}{sup cri} ≈ 15.4 ± 0.2 mJ/cm{sup 3}. This work provides the underlying physics of vortex-core reversals at non-zero temperatures, and potentiates the real application of vortex random access memory operating at elevated temperatures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

A detailed study of magnetization reversal in individual Ni nanowires

Magnetic nanowires have emerged as essential components for a broad range of applications. In many cases, a key property of these components is the switching field, which is studied as a function of the angle between the field and the nanowire. We found remarkable differences of up to 100% between the switching fields of different nanowires from the same fabrication batch. Our experimental results and micromagnetic simulations indicate that the nanowires exhibit a single domain behavior and that the switching mechanism includes vortex domain wall motion across the nanowire. The differences between the switching fields are attributed to different cross-sections of the nanowires, as found by electron microscopy. While a circular cross-section yields the smallest switching field values, any deviation from this shape results in an increase of the switching field. The shape of the nanowires' cross-sections is thus a critical parameter that has not been previously taken into account.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Stacking-engineered ferroelectricity in bilayer boron nitride

Stacking a ferroelectric Properties of layered van der Waals structures can depend sensitively on the stacking arrangement of constituent layers. This phenomenon has been exploited to engineer superconducting, correlated insulator, and magnetic states. Two groups now show that ferroelectricity can also be engineered through stacking: Parallel-stacked bilayers of hexagonal boron nitride exhibit ferroelectric switching even though the bulk material is not ferroelectric (see the Perspective by Tsymbal). To explore these phenomena, Yasuda et al. used transport measurements, whereas Vizner Stern et al. focused on atomic force microscopy. Science , abd3230 and abe8177, this issue p. 1458 and p. 1462 ; see also abi7296, p. 1389

Science & Technology - Other Topics↗
DOE OSTI2021

Tuning the room temperature ferromagnetism in Fe 5 GeTe 2 by arsenic substitution

In order to tune the magnetic properties of the cleavable high-Curie temperature ferromagnet Fe$_{5-x}$GeTe 2 , the effect of increasing the electron count through arsenic substitution has been investigated. Small additions of arsenic (2.5% and 5%) seemingly enhance ferromagnetic order in polycrystalline samples by quenching fluctuations on one of the three magnetic sublattices, whereas larger As concentrations decrease the ferromagnetic Curie temperature (T C ) and saturation magnetization. Furthermore, this work also describes the growth and characterization of Fe 4.8 AsTe 2 single crystals that are structurally analogous to Fe$_{5-x}$GeTe 2 but with some phase stability complications. Magnetization measurements reveal dominant antiferromagnetic behavior in Fe 4.8 AsTe 2 with a Néel temperature of $T_{\textrm{N}} \approx$ 42 K. A field-induced spin-flop below T N results in a switch from negative to positive magnetoresistance, with significant hysteresis causing butterfly-shaped resistance loops. In addition to reporting the properties of Fe 4.8 AsTe 2 , this work shows the importance of manipulating the individual magnetic sublattices in Fe$_{5-x}$GeTe 2 and motivates further efforts to control the magnetic properties in related materials by fine tuning of the Fermi energy or crystal chemistry.

36 MATERIALS SCIENCE↗