SEARCH · Search NASA

Results for “Programming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 937 records · Page 52

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Operations analysis (study 2.1). Program SEPSIM (solar electric propulsion stage simulation)

Program SEPSIM is a FORTRAN program which performs deployment, servicing, and retrieval missions to synchronous equatorial orbit using a space tug with a continuous low thrust upper stage known as a solar electric propulsion stage (SEPS). The SEPS ferries payloads back and forth between an intermediate orbit and synchronous orbit, and performs the necessary servicing maneuvers in synchronous orbit. The tug carries payloads between the orbiter and the intermediate orbit, deploys fully fueled SEPS vehicles, and retrieves exhausted SEPS vehicles when, and if, required. The program is presently contained in subroutine form in the Logistical On-orbit VEhicle Servicing (LOVES) Program, but can also be run independently with the addition of a simple driver program.

Lang, T. J.↗

NASA NTRS1974

Development of computer programs to determine the aerodynamic characteristics of complete light aircraft

A computer program for determining the flight characteristics of light aircraft was developed. The parameters which were used in the computer program are defined. The accuracy of the system for various types of airfoils is analyzed and the airfoils for which the system does not provide adequate data are identified. The application of a computer program for predicting the fuselage characteristics is discussed. The assumptions and parameters of the fuselage characteristics program are explained. It is stated that the computer programs make it possible to determine the response of a light aircraft to a small disturbance given the geometric and inertial characteristics of the aircraft.

Smetana, F. O.↗

NASA NTRS1974

A computer program for plotting stress-strain data from compression, tension, and torsion tests of materials

A computer program for plotting stress-strain curves obtained from compression and tension tests on rectangular (flat) specimens and circular-cross-section specimens (rods and tubes) and both stress-strain and torque-twist curves obtained from torsion tests on tubes is presented in detail. The program is written in FORTRAN 4 language for the Control Data 6000 series digital computer with the SCOPE 3.0 operating system and requires approximately 110000 octal locations of core storage. The program has the capability of plotting individual strain-gage outputs and/or the average output of several strain gages and the capability of computing the slope of a straight line which provides a least-squares fit to a specified section of the plotted curve. In addition, the program can compute the slope of the stress-strain curve at any point along the curve. The computer program input and output for three sample problems are presented.

Greenbaum, A.↗

NASA NTRS1975

NOLIN: A nonlinear laminate analysis program

A nonlinear, plane-stress, laminate analysis program, NOLIN, was developed which accounts for laminae nonlinearity under inplane shear and transverse extensional stress. The program determines the nonlinear stress-strain behavior of symmetric laminates subjected to any combination of inplane shear and biaxial extensional loadings. The program has the ability to treat different stress-strain behavior in tension and compression, and predicts laminate failure using any or all of maximum stress, maximum strain, and quadratic interaction failure criteria. A brief description of the program is presented including discussion of the flow of information and details of the input required. Sample problems and a complete listing of the program is also provided.

Kibler, J. J.↗

NASA NTRS1975

A FORTRAN program for determining aircraft stability and control derivatives from flight data

A digital computer program written in FORTRAN IV for the estimation of aircraft stability and control derivatives is presented. The program uses a maximum likelihood estimation method, and two associated programs for routine, related data handling are also included. The three programs form a package that can be used by relatively inexperienced personnel to process large amounts of data with a minimum of manpower. This package was used to successfully analyze 1500 maneuvers on 20 aircraft, and is designed to be used without modification on as many types of computers as feasible. Program listings and sample check cases are included.

Maine, R. E.↗

NASA NTRS1975

A program for contouring randomly spaced data

A description is given of a digital computer program which prepares contour plots of three dimensional data. The contouring technique uses a triangulation procedure. As presently configured, the program can accept up to 56,000 randomly spaced data points, although the required computer resources may be prohibitive. However, with relatively minor internal modifications, the program can handle essentially unlimited amounts of data. Up to 20 contouring intervals can be selected and contoured with either polygonal lines or smooth curves. Sample cases are illustrated. A general description of the main program and primary level subroutines is included to permit simple modifications of the program.

Hamm, R. W.↗

NASA NTRS1975

Description of CASCOMP Comprehensive Airship Sizing and Performance Computer Program, Volume 2

The computer program CASCOMP, which may be used in comparative design studies of lighter than air vehicles by rapidly providing airship size and mission performance data, was prepared and documented. The program can be used to define design requirements such as weight breakdown, required propulsive power, and physical dimensions of airships which are designed to meet specified mission requirements. The program is also useful in sensitivity studies involving both design trade-offs and performance trade-offs. The input to the program primarily consists of a series of single point values such as hull overall fineness ratio, number of engines, airship hull and empennage drag coefficients, description of the mission profile, and weights of fixed equipment, fixed useful load and payload. In order to minimize computation time, the program makes ample use of optional computation paths.

Davis, J.↗

NASA NTRS1975

The role of toxicology in the Apollo space program

Some of the major considerations are presented which governed the formation and application of the toxicology program employed in support of the Apollo program. The overriding concern of the program was the safety of crews exposed to trace contaminant gases for extended periods of time. The materials screening program employed, in conjunction with a well designed spacecraft environmental control system, helped to attain the goals set forth for the Apollo program. The knowledge gained from working with the toxicity problems and the identification of compounds in the space cabin atmosphere are of importance for continued efforts in manned space flight. Tabular data of spacecraft contaminants are presented.

Wayland J. Rippstein, Jr↗

NASA NTRS1975

PPP/nonreal-time trajectory program interface requirements and capabilities

The selection process for interfacing a nonreal time trajectory program with the procedures and performance program is outlined; the interface provides summary data timelines for any desired trajectory profile. Consideration was given to two separate digital programs for satisfying capabilities. One was the CDC 6400 digital program BANDITO, and the second was the UNIVAC 1110 SVDS program.

Mcgavern, J. L.↗

NASA NTRS1975

NASA compendium of satellite communications programs

A comprehensive review is given of worldwide satellite communication programs that range in time from the inception of satellite communications to mid-1974. Particular emphasis is placed on program results, including experiments conducted, communications system operational performance, and technology employed. The background for understanding these results is established through brief summaries of the program organization, system configuration, and satellite and ground terminal characteristics. Major consideration is given to the communications system aspects of each program, but general spacecraft technology and other experiments conducted as part of the same program are mentioned summarily.

Source record↗

NASA NTRS1976

Pollution technology program, can-annular combustor engines

A Pollution Reduction Technology Program to develop and demonstrate the combustor technology necessary to reduce exhaust emissions for aircraft engines using can-annular combustors is described. The program consisted of design, fabrication, experimental rig testing and assessment of results and was conducted in three program elements. The combustor configurations of each program element represented increasing potential for meeting the 1979 Environmental Protection Agency (EPA) emission standards, while also representing increasing complexity and difficulty of development and adaptation to an operational engine. Experimental test rig results indicate that significant reductions were made to the emission levels of the baseline JT8D-17 combustor by concepts in all three program elements. One of the Element I single-stage combustors reduced carbon monoxide to a level near, and total unburned hydrocarbons (THC) and smoke to levels below the 1979 EPA standards with little or no improvement in oxides of nitrogen. The Element II two-stage advanced Vorbix (vortex burning and mixing) concept met the standard for THC and achieved significant reductions in CO and NOx relative to the baseline. Although the Element III prevaporized-premixed concept reduced high power NOx below the Element II results, there was no improvement to the integrated EPA parameter relative to the Vorbix combustor.

Roberts, R.↗

NASA NTRS1975

Users manual for flight control design programs

Computer programs for the design of analog and digital flight control systems are documented. The program DIGADAPT uses linear-quadratic-gaussian synthesis algorithms in the design of command response controllers and state estimators, and it applies covariance propagation analysis to the selection of sampling intervals for digital systems. Program SCHED executes correlation and regression analyses for the development of gain and trim schedules to be used in open-loop explicit-adaptive control laws. A linear-time-varying simulation of aircraft motions is provided by the program TVHIS, which includes guidance and control logic, as well as models for control actuator dynamics. The programs are coded in FORTRAN and are compiled and executed on both IBM and CDC computers.

Nalbandian, J. Y.↗

NASA NTRS1976

A computer program for anisotropic shallow-shell finite elements using symbolic integration

A FORTRAN computer program for anisotropic shallow-shell finite elements with variable curvature is described. A listing of the program is presented together with printed output for a sample case. Computation times and central memory requirements are given for several different elements. The program is based on a stiffness (displacement) finite-element model in which the fundamental unknowns consist of both the displacement and the rotation components of the reference surface of the shell. Two triangular and four quadrilateral elements are implemented in the program. The triangular elements have 6 or 10 nodes, and the quadrilateral elements have 4 or 8 nodes. Two of the quadrilateral elements have internal degrees of freedom associated with displacement modes which vanish along the edges of the elements (bubble modes). The triangular elements and the remaining two quadrilateral elements do not have bubble modes. The output from the program consists of arrays corresponding to the stiffness, the geometric stiffness, the consistent mass, and the consistent load matrices for individual elements. The integrals required for the generation of these arrays are evaluated by using symbolic (or analytic) integration in conjunction with certain group-theoretic techniques. The analytic expressions for the integrals are exact and were developed using the symbolic and algebraic manipulation language.

Andersen, C. M.↗

NASA NTRS1976

Evaluation of two swept-infinite-wing potential/viscous-flow computer programs

Two computer programs capable of predicting the potential and viscous interacting flow around wings of infinite aspect ratio was evaluated. The programs are compared in terms of their capabilities, the approximations and the methods of solution used, and the input requirements. Six airfoils, each representative of a class of airfoils, are used as test airfoils. The results predicted by the programs are presented for each airfoil at sweep angles of 0, 20, and 40 degrees over a range of angles of attack. The results show that at zero sweep both programs predicted the aerodynamic coefficients well and generally in good agreement with measurements. At 20 and 40 degrees of sweep, as there are no experimental data available, definitive conclusions cannot be drawn about the accuracy of the predictions although the results are presented and discussed. The execution times are approximately the same for the two programs.

Arimilli, R. V.↗

NASA NTRS1976

Experimental clean combustor program, phase 2

The primary objectives of this three-phase program are to develop technology for the design of advanced combustors with significantly lower pollutant emission levels than those of current combustors, and to demonstrate these pollutant emission reductions in CF6-50C engine tests. The purpose of the Phase 2 Program was to further develop the two most promising concepts identified in the Phase 1 Program, the double annular combustor and the radial/axial staged combustor, and to design a combustor and breadboard fuel splitter control for CF6-50 engine demonstration testing in the Phase 3 Program. Noise measurement and alternate fuels addendums to the basic program were conducted to obtain additional experimental data. Twenty-one full annular and fifty-two sector combustor configurations were evaluated. Both combustor types demonstrated the capability for significantly reducing pollutant emission levels. The most promising results were obtained with the double annular combustor. Rig test results corrected to CF-50C engine conditions produced EPA emission parameters for CO, HC, and NOX of 3.4, 0.4, and 4.5 respectively. These levels represent CO, HC, and NOX reductions of 69, 90, and 42 percent respectively from current combustor emission levels. The combustor also met smoke emission level requirements and development engine performance and installation requirements.

Gleason, C. C.↗

NASA NTRS1976

Emissions and new technology programs for conventional spark-ignition aircraft engines

A long-range technology plan in support of general aviation engines was formulated and is being implemented at the Lewis Research Center. The overall program was described, and that part of the program that represents the in-house effort at Lewis was presented in detail. Three areas of government and industry effort involving conventional general-aviation piston engines were part of a coordinated overall plan: (1) FAA/NASA joint program, (2) NASA contract exhaust emissions pollution reduction program, and (3) NASA in-house emissions reduction and new technology program.

Wintucky, W. T.↗

NASA NTRS1977

DESAP 1: A structural design program with stress and displacement constraints. Volume 1: Theoretical and user's manual

A finite element program is presented for computer-automated, minimum weight design of elastic structures with constraints on stresses (including local instability criteria) and displacements. Volume 1 of the report contains the theoretical and user's manual of the program. Sample problems and the listing of the program are included in Volumes 2 and 3. The element subroutines are organized so as to facilitate additions and changes by the user. As a result, a relatively minor programming effort would be required to make DESAP 1 into a special purpose program to handle the user's specific design requirements and failure criteria.

Kiusalaas, J.↗

NASA NTRS1977

Thermochemical cycle analysis using linked CECS72 and HYDRGN computer programs

A combined thermochemical cycle analysis computer program was designed. Input to the combined program is the same as input to the thermochemical cycle analysis program except that the extent of the reactions need not be specified. The combined program is designed to be run interactively from a computer time-sharing terminal. This mode of operation allows correction or modification of the cycle to take place during cycle analysis. A group of 13 thermochemical cycles was used to test the combined program.

Donovan, L. F.↗