Search NASA⌕ Search

SEARCH · Search NASA

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Effect of wheel speed on magnetic and mechanical properties of melt spun Fe-6.5 wt.% Si high silicon steel

Here, Fe-Si electric steel is the most widely used soft magnetic material in electric machines and transformers. Increasing the silicon content from 3.2 wt.% to 6.5 wt.% brings about large improvement in the magnetic and electrical properties. However, 6.5 wt.% silicon steel is inherited with brittleness owing to the formation of B2 and D0 3 ordered phase. To obtain ductility in Fe-6.5wt.% silicon steel, the ordered phase has to be bypassed with methods like rapid cooling. In present paper, the effect of cooling rate on magnetic and mechanical properties of Fe-6.5wt.% silicon steel is studied by tuning the wheel speed during melt spinning process. The cooling rate significantly alters the ordering and microstructure, and thus the mechanical and magnetic properties. X-ray diffraction data shows that D0 3 ordering was fully suppressed at high wheel speeds but starts to nucleate at 10m/s and below, which correlates with the increase of Young’s modulus towards low wheel speeds as tested by nanoindentation. The grain sizes of the ribbons on the wheel side decrease with increasing wheel speeds, ranging from ~100 μm at 1m/s to ~8 μm at 30m/s, which lead to changes in coercivity.

36 MATERIALS SCIENCE↗

Understanding the tool influence function during sub-aperture belt-on-wheel glass polishing

The tool influence function (TIF) during sub-aperture belt-on-wheel polishing has been evaluated as a function of various process conditions (belt use/wear, dwell time, displacement, belt velocity, and wheel modulus and diameter) on fused silica glass workpieces using C e O 2 polishing media. TIF spots are circular or elliptical in shape with a largely flat bottom character. Furthermore, the volumetric removal rate varies significantly with belt use (or wear), stabilizing after ~<!-- ~ --> 15 m i n of use. A modified Preston model, where the pressure dependence is adjusted using a different scaling of the wheel modulus ( E w 0.5 ), largely predicts the volumetric removal rate over the range of process conditions evaluated. The relatively high volumetric removal rate of 30 -<!-- - --> 60 m m 3 / h using a fixed C e O 2 -in-resin-host belt offers a rapid, and hence, more economical, initial polish of aspheric and freeform optics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of wheel speed on the magnetic and mechanical properties of melt spun Fe-6.5 wt.% electric steel

Fe-Si electric steel is the most widely used soft magnetic materials in electric mahines and motors, transformers and generators. Improving the surperior magnetic and electric properties of 6.5 wt.% high silicon steel is essential for higher may improve energy efficiency and power density of electric machines. However, the brittleness due to the formation of B2 and D03 ordered phases in high silicon steel make it difficult forbids for the application of high silicon steel. It is known that these ordered phases can be fully or partially suppressed by rapid cooling. However, further study is needed to understand the extend of cooling on the magnetic and mechanical properties of 6.5 wt.% silicon steel with various degree of ordering. By tuning the wheel speed from 1m/s to 30m/s with several intervals of the melt spinning process, varying degrees of cooling were achieved on 6.5 wt.% silicon steel ribbons. The cooling rate significant altered the ordering, microstructure size scale, and thus the mechanical and magnetic properties. TEM results showed that D03 ordering can be fully suppressed at high wheel speed, but started to nucleate at 5m/s and below, which correlates with the hardness and Young’s modulus increase towards low wheel speeds as tested by micro and nano indentation. The grain sizes of the ribbons on the wheel side decreased with increasing wheel speeds being ~100 micron at 1m/s and ~8 micron at 30m/s, which led to the change in coercivity. Saturation magnetization and electric resistivity of the ribbons remained about 190 emu/g and 84 microhm *cm, which appeared to be mainly depend on the chemistry.

Fe-6.5%Si Steel↗

The Effect of Pre-Stressing on the Static Indentation Load Capacity of the Superelastic 60NiTi

Superelastic nickel-titanium alloys, such as 60NiTi (60Ni-40Ti by wt.%), are under development for use in mechanical components like rolling element bearings and gears. Compared to traditional bearing steels, these intermetallic alloys, when properly heat-treated, are hard but exhibit much lower elastic modulus (approx.100 GPa) and a much broader elastic deformation range (approx.3 percent or more). These material characteristics lead to high indentation static load capacity, which is important for certain applications especially space mechanisms. To ensure the maximum degree of elastic behavior, superelastic materials must be pre-stressed, a process referred to as "training" in shape memory effect (SME) terminology, at loads and stresses beyond expected use conditions. In this paper, static indentation load capacity tests are employed to assess the effects of pre-stressing on elastic response behavior of 60NiTi. The static load capacity is measured by pressing 12.7 mm diameter ceramic Si3N4 balls into highly polished, hardened 60NiTi flat plates that have previously been exposed to varying levels of pre-stress (up to 2.7 GPa) to determine the load that results in shallow but measurable (0.6 m, 25 in. deep) permanent dents. Hertz stress calculations are used to estimate contact stress. Without exposure to pre-stress, the 60NiTi surface can withstand an approximately 3400 kN load before significant denting (>0.4 m deep) occurs. When pre-stressed to 2.7 GPa, a static load of 4900 kN is required to achieve a comparable dent, a 30 percent increase. These results suggest that stressing contact surfaces prior to use enhances the static indentation load capacity of the superelastic 60NiTi. This approach may be adaptable to the engineering and manufacture of highly resilient mechanical components such as rolling element bearings.

DellaCorte, Christopher↗

The Effect of Fiber Strength Stochastics and Local Fiber Volume Fraction on Multiscale Progressive Failure of Composites

Continuous fiber unidirectional polymer matrix composites (PMCs) can exhibit significant local variations in fiber volume fraction as a result of processing conditions that can lead to further local differences in material properties and failure behavior. In this work, the coupled effects of both local variations in fiber volume fraction and the empirically-based statistical distribution of fiber strengths on the predicted longitudinal modulus and local tensile strength of a unidirectional AS4 carbon fiber/ Hercules 3502 epoxy composite were investigated using the special purpose NASA Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC); local effective composite properties were obtained by homogenizing the material behavior over repeating units cells (RUCs). The predicted effective longitudinal modulus was relatively insensitive to small (~8%) variations in local fiber volume fraction. The composite tensile strength, however, was highly dependent on the local distribution in fiber strengths. The RUC-averaged constitutive response can be used to characterize lower length scale material behavior within a multiscale analysis framework that couples the NASA code FEAMAC and the ABAQUS finite element solver. Such an approach can be effectively used to analyze the progressive failure of PMC structures whose failure initiates at the RUC level. Consideration of the effect of local variations in constituent properties and morphologies on progressive failure of PMCs is a central aspect of the application of Integrated Computational Materials Engineering (ICME) principles for composite materials.

multiscale analysis↗

Physical characterization of High Entropy Alloys through Differential Scanning Calorimetry and Nanoindentation

In recent years several accelerator facilities have been limiting their beam power output not due to constraint of the accelerators but by concerns on the survivability of their targets, which in turn has led to R&D efforts into new, more resistant materials. One of these novel materials are High Entropy Alloys, the main focus of the internship project. This paper details the activities performed during the CCI 10-week internship by the authors, as well as to discuss the results obtained from said internship. The project consisted of the physical characterization of 12 batches of High Entropy Alloys (HEAs); the methods used to analyze the materials were Nanoindentation, which allows to determine the elastic modulus of the material and its hardness, and Differential Scanning Calorimetry (DSC), allowing the determination of specific heat.

Pacheco Uribe, Rene↗

Design and Development of Novel Equiatomic Refractory Multi Principal elemental Alloys Based on MoNbTi System for Use in Irradiation Environments

Multi Principal Elemental Alloys (MPEA) have emerged as promising materials for next-generation nuclear reactors due to their exceptional irradiation resistance. Eight equiatomic MPEA based on the MoNbTi system, comprising of elements with low thermal neutron absorption cross-sections were explored using a combined approach employing empirical parameter estimations, and CALPHAD simulations by which the phases and elemental segregation observed in all the alloys in the as-cast state were predicted. Solution heat treatment at 1500°C transformed five alloys into single-phase matrix materials, enhancing homogeneity and reducing hardness. The densities of the alloys ranged between 6.47 to 7.68 g/cm3, hardness between 472 and 656 VHN, Young’s modulus between 142 GPa to 169 GPa, shear modulus between 54 GPa and 62 GPa, bulk modulus between 117 GPa to 194 GPa and Poisson’s ratio between 0.3 to 0.35. The in-situ high temperature Xray diffraction results, differential scanning calorimetry and dilatometry results up to 1000°C suggested the high temperature phase stability of the MPEA. Subsequent ageing heat treatment at 800 and 1000 oC for 96 hours revealed significant secondary phase precipitation in MoNbTiZr, MoNbTiZrV, and MoNbTiCrA. Oxidation studies at 800 oC for 24 hours in air revealed superior oxidation resistance and cubic rate law dependence in Cr containing MPEA especially in MoNbTiCrAl, while severe mass gain resulting in total disintegration and exfoliation in MoNbTiZr and MoNbTiZrV. This comprehensive study underscores the potential of novel MPEA as promising materials for advanced nuclear reactor applications, shedding light on their microstructural control, mechanical properties, thermal stability, and oxidation resistance.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Elastic properties of gamma-Pu by resonant ultrasound spectroscopy

Despite intense experimental and theoretical work on Pu, there is still little understanding of the strange properties of this metal. We used resonant ultrasound spectroscopy method to investigate the elastic properties of pure polycrystalline Pu at high temperatures. Shear and longitudinal elastic moduli of the {gamma}-phase of Pu were determined simultaneously and the bulk modulus was computed from them. A smooth linear and large decrease of all elastic moduli with increasing temperature was observed. We calculated the Poisson ratio and found that it increases from 0.242 at 519K to 0.252 at 571K.

36 MATERIALS SCIENCE↗

A first principle study of the pressure dependent elastic properties of monazite LaPO{sub 4}

DFT based ab-initio simulations have been performed to study the effect of pressure on the elastic properties of monazite LaPO{sub 4} which is a promising host material for immobilization of high level nuclear waste. The phase is found to be stable up to 30 GPa. The calculated polycrystalline bulk, shear and Young moduli show an increasing trend as a function of pressure. The ductility and anisotropy in shear modulus of the material have been found to increase with pressure; whilethe bulk modulus anisotropy decreases with pressure.

36 MATERIALS SCIENCE↗

Pressure-induced stiffness of Au nanoparticles to 71 GPa under quasi-hydrostatic loading

The compressibility of nanocrystalline gold (n-Au, 20 nm) has been studied by x-ray total scattering using high-energy monochromatic x-rays in the diamond anvil cell under quasi-hydrostatic conditions up to 71 GPa. The bulk modulus, K 0 , of the n-Au obtained from fitting to a Vinet equation of state is ~196(3) GPa, which is about 17% higher than for the corresponding bulk materials (K 0 : 167 GPa). At low pressures (<7 GPa), the compression behavior of n-Au shows little difference from that of bulk Au. With increasing pressure, the compressive behavior of n-Au gradually deviates from the equation of state (EOS) of bulk gold. Analysis of the pair distribution function, peak broadening and Rietveld refinement reveals that the microstructure of n-Au is nearly a single-grain/domain at ambient conditions, but undergoes substantial pressure-induced reduction in grain size until 10 GPa. The results indicate that the nature of the internal microstructure in n-Au is associated with the observed EOS difference from bulk Au at high pressure. Full-pattern analysis confirms that significant changes in grain size, stacking faults, grain orientation and texture occur in n-Au at high pressure. We have observed direct experimental evidence of a transition in compressional mechanism for n-Au at ~20 GPa, i.e. from a deformation dominated by nucleation and motion of lattice dislocations (dislocation-mediated) to a prominent grain boundary mediated response to external pressure. In conclusion, the internal microstructure inside the nanoparticle (nanocrystallinity) plays a critical role for the macro-mechanical properties of nano-Au.

high pressure DAC↗

Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) nanocomposites with optimal mechanical properties

With the ultimate goal to design renewable polymer nanocomposites with optimal mechanical properties, this study reports an investigation of structure-property relationships for a model system - silica/poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHx) nanocomposites. Two molecular weights of PHBHx (M{sub w} = 903,000 g/mol and M{sub w} = 633,000 g/mol) and two types of silica nanoparticles (nominally spheres and fibers according to the manufacturer) were used to prepare the nanocomposites. Small-angle X-ray scattering shows that the sphere and fiber nanoparticles had similar surface areas and primary particle size, but differed in degree of aggregation of the primary particles. The thermal stability of the PHBHx matrix was slightly improved by the addition of nanofillers. Simultaneous improvement of both stiffness and toughness was observed at 1-wt% loading for the higher molecular weight matrix. The more highly aggregated SiO{sub 2} fibers had a greater toughening effect than the SiO{sub 2} spheres. Compared to the unfilled polymer matrix, a 30% increase in Young's modulus and 34% increase in toughness were obtained for the 1-wt% SiO{sub 2} fiber/PHBHx072 nanocomposite. The addition of SiO{sub 2} spheres to PHBHx072 resulted in the same increase in Young's modulus (30%) but a smaller increase (11%) in toughness. The dramatic increases in modulus for PHBHx072 cannot be explained on the basis of two-component micromechanical models. Apparently the filler alters the character of the semicrystalline matrix. When the loading was 3 wt% and above, Young's modulus continued to increase, but the strain at break and toughness decreased. The ultimate strength did not change compared with the unfilled polymer. In order to understand the mechanical properties observed, the thermal behavior, spherulitic morphology and the deformation mechanisms of the nanocomposites and the dispersion state of the nanofillers were studied. We found that a high molecular weight of the polymer matrix, weak interfacial adhesion and a good dispersion of the nanofillers are necessary to improve toughness and stiffness simultaneously.

36 MATERIALS SCIENCE↗

Influence of temperature on the lattice misfit and elastic moduli of a Ni based single crystal superalloy with high volume fraction of γ′ phase

Highlights: • The variation of the lattice misfit with temperature in a Ni based single-crystal superalloy with high volume fraction of γ' phase was determined by high-temperature X-ray diffraction (HT-XRD) technique at temperatures between 25 °C and 1200 °C. • When the temperature was higher than 1100 °C, the γ' phase obviously dissolved, leading to a lower content of Mo and Re in the γ phase, and then resulted in a smaller absolute value of the lattice misfit. • The contribution of dissolution of γ′ phase to the reduction of the misfit increased with rising temperature and reached 29.5% at 1200 °C. • When the temperature exceeded 1100 °C, the difference of elastic moduli of γ and γ′ phases increased with rising temperature was attributed to the elastic modulus of γ phase decreased significantly. - Abstract: The variation of the lattice parameter with temperature in a Ni based single-crystal superalloy with high volume fraction of γ′ phase IC32 was determined by high-temperature X-ray diffraction (HT-XRD) technique at temperatures between 25 °C and 1200 °C. The effects of the temperature, especially the ultra-high temperature (beyond 1100 °C), on lattice misfit, elastic moduli, γ′ volume fraction and composition of γ, γ′ phases were investigated in this study. The results show that the absolute value of lattice misfit first increased and then decreased with increasing temperature and reached the maximum of 0.53% at 1100 °C. When the temperature was higher than 1100 °C, the γ′ precipitate obviously dissolved, leading to a lower content of Mo and Re in the γ phase, and then resulted in a smaller absolute value of lattice misfit. The contribution of dissolution of γ′ phase to the reduction of the misfit increased with rising temperature and reached 29.5% at 1200 °C. Moreover, when the temperature was above 1100 °C, the elastic moduli of the γ phase and alloy decreased significantly, while this phenomenon was not observed in the γ′ phase.

36 MATERIALS SCIENCE↗

Mechanical Characterization of High-Temperature Carbon Fiber-Polyphenylene Sulfide Composites for Large Area Extrusion Deposition Additive Manufacturing

Additive manufacturing (AM) is evolving from rapid prototyping to production of structural components. The widespread application of AM demands a high level of mechanical performance from these components, and it is therefore essential to improve feedstock material in order to meet these mechanical expectations. However, compared to traditional manufacturing techniques, the mechanical properties of AM materials and their resulting components are not well understood. In this study, we investigated the processability, microstructure, and mechanical performance of twin-screw compounded short carbon fiber reinforced polyphenylene sulfide (PPS) pellets as a feedstock material for big area AM (BAAM). The performance of the AM components was compared to that of traditional processing methods, namely injection molding (IM) and extrusion-compression molding (ECM). It was found that the AM composites exhibited 118% lower tensile strength and 55% lower tensile modulus when compared to traditional injection molding composite specimens; however, AM composites exhibited comparable properties to ECM composites. This response was attributed to highly aligned fibers in IM and AM samples. However, the AM composites contained porosity (15.5% volume), which reduced their mechanical properties in comparison to ECM composites. Finally, the IM process showed the maximum amount of fiber attrition with minimum porosity (0.007% volume), while the ECM process exhibited the least fiber attrition with 4.3% volume porosity.

36 MATERIALS SCIENCE↗

X-ray diffraction reveals two structural transitions in szomolnokite

Hydrated sulfates have been identified and studied in a wide variety of environments on Earth, Mars, and the icy satellites of the solar system. The subsurface presence of hydrous sulfur-bearing phases to any extent necessitates a better understanding of their thermodynamic and elastic properties at pressure. End-member experimental and computational data are lacking and are needed to accurately model hydrous, sulfur-bearing planetary interiors. In this work, high-pressure X-ray diffraction (XRD) and synchrotron Fourier-transform infrared (FTIR) measurements were conducted on szomolnokite (FeSO 4 ·H 2 O) up to ~83 and 24 GPa, respectively. This study finds a monoclinic-triclinic (C2/c to P1¯) structural phase transition occurring in szomolnokite between 5.0(1) and 6.6(1) GPa and a previously unknown triclinic-monoclinic (P1¯ to P2 1 ) structural transition occurring between 12.7(3) and 16.8(3) GPa. The high-pressure transition was identified by the appearance of distinct reflections in the XRD patterns that cannot be attributed to a second phase related to the dissociation of the P1¯ phase, and it is further characterized by increased H 2 O bonding within the structure. We fit third-order Birch-Murnaghan equations of state for each of the three phases identified in our data and refit published data to compare the elastic parameters of szomolnokite, kieserite (MgSO 4 ·H 2 O), and blödite (Na 2 Mg(SO 4 ) 2 ·4H 2 O). At ambient pressure, szomolnokite is less compressible than blödite and more than kieserite, but by 7 GPa both szomolnokite and kieserite have approximately the same bulk modulus, while blödite’s remains lower than both phases up to 20 GPa. Furthermore, these results indicate the stability of szomolnokite’s high-pressure monoclinic phase and the retention of water within the structure up to pressures found in planetary deep interiors.

58 GEOSCIENCES↗

Microstructural evolution and micromechanical properties of gamma-irradiated Au ball bonds

The effect of gamma radiation on the mechanical and structural properties of gold ball bonds was investigated. Gold wires from thermosonic wire bonding were exposed to gamma rays from a Cobalt-60 source at a low dose (5 Gy). The load–depth curve of nanoindentation for the irradiated gold wire bond has an apparent staircase shape during loading compared to the as-received sample. The hardness of the specimens calculated from the nanoindentation shows an increase in value from 0.91 to 1.09 GPa for specimens after exposure. The reduced elastic modulus for irradiated specimens significantly increased as well, with values from 75.18 to 98.55 GPa. The change in intrinsic properties due to gamma radiation was investigated using dual-focused ion beam and high-resolution transmission electron microscope analysis. The dual-focused ion beam and high-resolution transmission electron microscope images confirmed the changes in grain structure and the presence of dislocations. The scanning electron microscope micrographs of focused ion beam cross sections showed that the grain structure of the gold became elongated and smaller after exposure to gamma rays. Meanwhile, high-resolution transmission electron microscopy provided evidence that gamma radiation induced dislocation of the atomic arrangement. - Highlights: • Nanoindentation technique provides a detailed characterisation of Au ball bond. • P–h curve of irradiated Au ball bond shows an apparent pop-in event. • Hardness and reduced modulus increased after exposure. • Elongated and smaller grain structure in irradiated specimens • Prevalent presence of dislocations in the atomic arrangement.

36 MATERIALS SCIENCE↗

High pressure raman spectroscopy and X-ray diffraction of K2Ca(CO3)2 bütschliite: multiple pressure-induced phase transitions in a double carbonate

Abstract The crystal structure and bonding environment of K 2 Ca(CO 3 ) 2 bütschliite were probed under isothermal compression via Raman spectroscopy to 95 GPa and single crystal and powder X-ray diffraction to 12 and 68 GPa, respectively. A second order Birch-Murnaghan equation of state fit to the X-ray data yields a bulk modulus, $${K}_{0}=46.9$$ K 0 = 46.9 GPa with an imposed value of $${K}_{0}^{\prime}= 4$$ K 0 ′ = 4 for the ambient pressure phase. Compression of bütschliite is highly anisotropic, with contraction along the c -axis accounting for most of the volume change. Bütschliite undergoes a phase transition to a monoclinic C 2/ m structure at around 6 GPa, mirroring polymorphism within isostructural borates. A fit to the compression data of the monoclinic phase yields $${V}_{0}=322.2$$ V 0 = 322.2 Å 3 $$,$$ , $${K}_{0}=24.8$$ K 0 = 24.8 GPa and $${K}_{0}^{\prime}=4.0$$ K 0 ′ = 4.0 using a third order fit; the ability to access different compression mechanisms gives rise to a more compressible material than the low-pressure phase. In particular, compression of the C 2/ m phase involves interlayer displacement and twisting of the [CO 3 ] units, and an increase in coordination number of the K + ion. Three more phase transitions, at ~ 28, 34, and 37 GPa occur based on the Raman spectra and powder diffraction data: these give rise to new [CO 3 ] bonding environments within the structure.

36 MATERIALS SCIENCE↗

Ultrasound nondestructive characterization of transparent spinel

Ceramic materials have attractive attributes for applications that experience high stresses or strain rates. Compared to metal-based systems, ceramics offer a lower areal density which reduces weight, but do not depreciate the integrity of other properties. The ability to tailor the microstructure of ceramics used in armor systems is a common way to increase specific mechanical properties or obtain certain material characteristics. Properties such as elastic modulus, hardness, and density are those that are typically desired to be enhanced. By modifying the microstructure one can obtain a ceramic with these enhanced properties as well as high optical transmission across a wide range of the electromagnetic spectrum. The testing of these properties and ballistic performance is usually destructive, expensive, and time consuming. Common assessments using ultrasonic NDE usually include spatially locating large flaws, sonic velocity measurements, and elastic property measurements. The use of acoustic spectroscopy to go beyond typical ultrasonic NDE in structural ceramics and allow for the use of a microstructural characterization tool is investigated in this paper. Ultrasound absorption by lithium fluoride precipitates in aluminate spinel (MgAl{sub 2}O{sub 4}) present as defined spectral peaks. Average heterogeneity size determination in magnesium aluminate spinel MgAl{sub 2}O{sub 4} by method of acoustic spectroscopy is shown.

36 MATERIALS SCIENCE↗

Resin Testing and Modeling for Optimal Composite Processing

Polymer composites have properties such as high strength and stiffness, low weight, good thermal and chemical stability, as well as impact and abrasion resistance that make them ideal for high-performance applications. The chemistries of these materials are continuously improving, so determining their properties is vital for successfully producing them and achieving the desired results. Multiple methods can be employed to monitor characteristics such as heat flow, weight, dimension, and modulus as a function of time and temperature. By analyzing this information, models can be developed to predict outcomes of parameters not tested for. In one application, materials proposed for wet filament winding and the production of high pressure vessels can be analyzed to verify they will have the necessary low viscosity for good fiber wetting and long pot life for the extended handling inherent to this process. Such data about a prospective system provides valuable information on how that material could ultimately be processed to yield the desired part.

36 MATERIALS SCIENCE↗