Search NASA⌕ Search

SEARCH · Search NASA

Results for “scanning electron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Characterization of as-welded microstructure of heat-affected zone in modified 9Cr–1Mo–V–Nb steel weldment

Non-equilibrium microstructure of the heat-affected zone (HAZ) in the as-welded modified 9Cr–1Mo–V–Nb pipe steel (P91) weldment deposited by gas tungsten arc welding (GTAW) and flux core arc welding (FCAW) has been characterized by field-emission scanning electron microscope (FESEM) and electron backscatter diffraction (EBSD). The heterogeneous structures in the sub-layers of the as-welded HAZ are attributable to phase transformations caused by the welding thermal cycles and the local structure variations in the as-received base metal. Coarse-grained heat-affected zone (CGHAZ) has a prior austenite grain (PAG) size of 20 μm. Fine uniformly-distributed precipitates and a higher fraction of MX carbonitrides are observed in the CGHAZ. Fine-grained heat-affected zone (FGHAZ) consists of the finest grains (1.22 μm measured by EBSD, 5 μm PAG size), coarse undissolved M{sub 23}C{sub 6} carbides within the PAG boundaries and fine nucleated M{sub 23}C{sub 6} particles within the martensite laths. Inter-critical heat-affected zone (ICHAZ) consists of partially austenitized grains and over-tempered martensite laths. EBSD kernel average misorientation (KAM) map in the FGHAZ close to the ICHAZ illustrates the greatest local strain variations with a moderate normalized KAM value of 0.92°. The majority (88.1%) of the matrix grains in the CGHAZ are classified as deformed grains by EBSD grain average misorientation (GAM) evaluation. The FGHAZ close to the ICHAZ has the most recrystallized grains with an area fraction of 14.4%. The highest density variation of precipitates within grains in the FGHAZ originates from the inhomogeneous chemistry in the base metal. - Highlights: •A comprehensive characterization of the as-welded HAZ of P91 weldment is conducted. •Structural features in the each layer of the HAZ are quantified by EBSD. •Structural heterogenities in HAZ are due to welding cycle and base metal structure. •FGHAZ contains the finest grain structure and largest precipitate density variation.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Accumulative fold-forging (AFF) as a novel severe plastic deformation process to fabricate a high strength ultra-fine grained layered aluminum alloy structure

Highlights: • A novel SPD process named as AFF was introduced. • AFF process is based on the repetitive forging of folded metal foils. • This new method possesses an exceptional capability for fabrication of UFG layered structures. • An AA8006 aluminum alloy layered material with the UFG structure of 200–300 nm was produced. • An enhanced hardness up to ~ 100% was attained owing to the UFG and layered structures. - Abstract: A novel severe plastic deformation (SPD) process termed accumulative fold forging (AFF) is introduced to fabricate a homogenous ultra-fine grained (UFG) layered metal structure by repetitive folding and forging aluminum alloy foil. The present work studies AFF applied to thin foils of AA8006 Al-Fe-Mn aluminum alloy after 26 folding steps to produce a UFG structure containing 67,108,864 layers across a 2 mm thickness. The structure of the layers and grain refinement are studied using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and scanning-transmission electron microscopy (STEM) analysis. The results indicate a well-bonded inter-layer structure with an average grain size of about 200 nm parallel and 250 nm perpendicular to the forging direction, while dislocation density increased to ~ 7.2 × 10{sup 15} m{sup − 2} following AFF. The mechanical strength of the aluminum foil is evaluated in the terms of indentation hardness testing before and after AFF process. The processed UFGed layered material exhibited an average hardness value of ~ 61.5 Vickers as compared to the initial value of ~ 30.4 Vickers for the annealed foil alloy, which indicates an improvement of ~ 100% due to the contributions of grain refinement, work hardening and interfacial strengthening of the bonded layers.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Hydrothermal synthesis of Y{sub 2}O{sub 3} coated Y{sub 2}O{sub 3}:Eu{sup 3+} nanotubes for enhanced photoluminescence properties

Highlights: • Eu{sup 3+} doped Y{sub 2}O{sub 3} nanotubes. • Hydrothermal synthesis of Y{sub 2}O{sub 3} coated Y{sub 2}O{sub 3}:Eu{sup 3+} nanostructures assissted with a further heat treatment. • Tunable coating ratios of Y{sub 2}O{sub 3} coated Y{sub 2}O{sub 3}:Eu{sup 3+} nanophosphor. • Enhanced photoluminescence intensity of Y{sub 2}O{sub 3}:Eu{sup 3+} more than 60% by Y{sub 2}O{sub 3} surface coating. - Abstract: Novel Y{sub 2}O{sub 3} coated Y{sub 2}O{sub 3}:Eu{sup 3+} nanotubes with different coating ratios were synthesized successfully by a facile two-step process, including hydrothermal synthesis of Y(OH){sub 3} coated Y(OH){sub 3}:Eu{sup 3+} as precursors and then calcination of them at 1000 °C for 2 h. X-ray diffraction patterns and field emission scanning electron microscope images indicated these Y{sub 2}O{sub 3} coated Y{sub 2}O{sub 3}:Eu{sup 3+} phosphors possess tubular nanostructures. The photoluminescence properties of Y{sub 2}O{sub 3} coated Y{sub 2}O{sub 3}:Eu{sup 3+} were systematically investigated by photoluminescence spectra, and photoluminescence enhancement was observed after proper coating. In other words, the coating ratio played a crucial role in photoluminescence efficiency. When it was 1/9, the photoluminescence intensity of {sup 5}D{sub 0} → {sup 7}F{sub 2} emission (about 613 nm) was 60% higher than that of Y{sub 2}O{sub 3}: Eu{sup 3+} phosphors under 255 nm excitation. Therefore, surface coating may be an alternative route for enhanced photoluminescence properties of the Y{sub 2}O{sub 3}:Eu{sup 3+} red-emitting phosphor.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Ferromagnetic-to-Paramagnetic Phase Transition of MnAs Studied by Calorimetry and Magnetic Measurements

Manganese monoarsenide samples have been prepared by the sealed-ampule technique and characterized by X-ray diffraction, differential thermal analysis, and scanning electron microscopy. The hexagonal- to-orthorhombic phase transition of MnAs has been studied using differential scanning calorimetry (DSC) and magnetic measurements. The enthalpy and temperature range of the transition have been determined to be ΔH =–5.6 J/g and 312.5–319 K, respectively. The enthalpy and temperature range of the transition are influenced by the quality of the samples. The samples containing inclusions of the metastable, orthorhombic phase have a lower enthalpy and broader temperature range of the magnetostructural transformation of manganese monoarsenide. It has been demonstrated that DSC is an effective tool for assessing the quality of MnAs samples. Temperature dependences of specific magnetization and magnetic permeability for MnAs lend support to the DSC results. From these data, the Curie temperature of MnAs has been determined to be 40°C, in good agreement with previously reported data.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Micro- and nano-structural evolutions in white Portland cement/pulverized fuel ash cement pastes due to deionized-water leaching

Thin slices of white Portland cement-low calcium pulverized fuel ash (pfa) blended cement pastes containing 30 or 50% pfa were leached progressively in de-ionized water. The paste with 50% pfa was aged 13 years prior to leaching and those with 30% pfa were aged 1 and 13 years. Pastes were leached for up to 75 days and were characterized using thermal analysis, X-ray diffraction, analytical scanning and transmission electron microscopy, and solid-state nuclear magnetic resonance spectroscopy. Leaching affected the pastes in the following sequence: (i) crystals of Ca(OH){sub 2} large enough to be resolved by backscattered electron imaging were removed completely prior to any effect on C-A-S-H; (ii) the Ca/Si ratio of C-A-S-H reduced from ≈ 1.4 to ≈ 1.0 whilst the aluminosilicate structure was unaffected; (iii) further reduction in the Ca/Si ratio of C-A-S-H was accompanied by lengthening of the aluminosilicate chains; (iv) the Ca/Si ratio of C-A-S-H reduced ultimately to ≈ 0.6.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Study of How LaFeO 3 and CaTiO 3 Supports Affect the Oxidation, Hydrogenation, and Methane Steam Reforming Activity of Pt and Ni Catalysts

The structure and catalytic properties of Pt and Ni supported on thin films of LaFeO 3 and CaTiO 3 , prepared by Atomic Layer Deposition (ALD), were investigated. X-Ray diffraction (XRD) and scanning transmission electron microscopy (STEM) show that reduction at 1073 K causes Pt-Fe intermetallic compound formation for Pt/LaFeO 3 . For Pt/CaTiO 3 , 1073-K reduction induces local decomposition of the CaTiO 3 with migration of Ti to the Pt. Reduced Pt/LaFeO 3 and Pt/CaTiO 3 exhibited CO-oxidation activity similar to that for Pt supported on MgAl 2 O 4 but were much less active for propane oxidation and hydrogenation of 1-hexene and toluene. In contrast, Ni/CaTiO 3 behaved similarly to a conventional supported Ni catalyst for the methane-steam-reforming (MSR) and 1-hexene hydrogenation. There was also no evidence for local decomposition of the perovskite in the vicinity of the Ni particles. Furthermore, the results obtained in this study demonstrate that metal-perovskite interactions that affect reactivity are specific to each component.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Isomorphism and solid solutions among Ag- and Au-selenides

Au-Ag selenides were synthesized by heating stoichiometric mixtures of elementary substances of initial compositions Ag{sub 2−x}Au{sub x}Se with a step of x=0.25 (0≤x≤2) to 1050 °C and annealing at 500 °C. Scanning electron microscopy, optical microscopy, electron microprobe analysis and X-ray powder diffraction methods have been applied to study synthesized samples. Results of studies of synthesized products revealed the existence of three solid solutions with limited isomorphism Ag↔Au: naumannite Ag{sub 2}Se – Ag{sub 1.94}Au{sub 0.06}Se, fischesserite Ag{sub 3}AuSe{sub 2} - Ag{sub 3.2}Au{sub 0.8}Se{sub 2} and gold selenide AuSe - Au{sub 0.94}Ag{sub 0.06}Se. Solid solutions and AgAuSe phases were added to the phase diagram of Ag-Au-Se system. Crystal-chemical interpretation of Ag-Au isomorphism in selenides was made on the basis of structural features of fischesserite, naumannite, and AuSe. - Highlights: • Au-Ag selenides were synthesized. • Limited Ag-Au isomorphism in the selenides is affected by structural features. • Some new phases were introduced to the phase diagram Ag-Au-Se.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Intercalation of Nanopolyaniline with Nanobentonite and Manganese Oxide Nanoparticles as a Novel Nanocomposite to Remediate Cobalt/Zinc and Their Radioactive Nuclides {sup 60}Co/{sup 65}Zn

A novel nanocomposite based on the combination of nanobentonite with nanopolyaniline and nanomanganese oxide (N-Bent–NPANI–NMn{sub 3}O{sub 4}) was synthesized and investigated to extract Co/Zn ions from water using batch technique and {sup 60}Co/{sup 65}Zn radionuclides from radioactive wastewater using column techniques. Characterization was established by High resolution-transmission electron microscopy (HR-TEM), Scanning electron microscope, X-ray diffraction (XRD), thermal gravimetric analysis (TGA) and Fourier transform infrared spectrophotometer. The image of HR-TEM indicated that the produced nanocomposite was ranged from 59.07 to 83.38 nm. Solution pH, time of reaction, amount of solid and metal concentration, all of these parameters were inspected and optimized as fundamental factors during the extraction process. The obtained results implied that the ideal conditions for extraction were pH 6 and 7, reaction time 10 and 20 min, for Co and Zn ions, respectively. The highest removal capacities were found 255.28 and 202.22 mg g{sup −1} for Co and Zn, respectively by using 5 mg nanocomposite. Excellent recoveries were obtained as 94.0–94.5% and 92.0–93.0% for removal of Co–{sup 60}Co and of Zn–{sup 65}Zn ions, respectively from the examined samples. Graphical Abstract: .

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Synthesis and study of Pd-Rh alloy nanoparticles and alumina-supported low-content Pd-Rh catalysts for CO oxidation

Highlights: • A bimetallic Pd-Rh/alumina catalyst was prepared using coordination compound. • The peculiarities of precursor decomposition under different media were studied. • Catalytic performance and stability were examined in a CO oxidation reaction. - Abstract: Palladium and rhodium are known to be partly miscible metals. In present work, the peculiarities of coordination compound [Pd(NH{sub 3}){sub 4}]{sub 3}[Rh(NO{sub 2}){sub 6}]{sub 2} decomposition with formation of nanosized solid solutions under different atmospheres were studied by means of thermal gravimetry. Formation of alloy nanoparticles were confirmed by powder X-ray diffraction analysis, scanning and transmission electron microscopies. A bimetallic Pd-Rh/alumina catalyst was prepared by incipient wetness impregnation using coordination compound [Pd(NH{sub 3}){sub 4}]{sub 3}[Rh(NO{sub 2}){sub 6}]{sub 2} as a precursor. Monometallic reference samples were obtained using [Pd(NH{sub 3}){sub 4}](NO{sub 3}){sub 2} and Na{sub 3}[Rh(NO{sub 2}){sub 6}], correspondingly. Catalytic performance and stability of the catalysts were examined in a model reaction of CO oxidation in a prompt thermal aging regime. The environment of precursor decomposition was shown to affect noticeably both the initial activity and stability of the samples in the studied reaction. Reductive atmosphere in comparison with inert and oxidative ones facilitates the formation of the smallest active component species, which demonstrate highest initial activity but worst stability.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Investigations of room temperature multiferroic and magneto-electric properties of (1-Φ) PZTFT-Φ CZFMO particulate composites

Multiferroic composites consisting of a single-phase multiferroic [0.6(PbZr 0.53 Ti 0.47 O 3 )-0.4(PbFe 0.5 Ta 0.5 )O 3 ] as a matrix and a magnetostrictive phase (Co 0.6 Zn 0.4 Fe 1.7 Mn 0.3 O 4 ) dispersed in the matrix are fabricated via hybrid synthesis technique. The structure and surface morphology studies using x-ray diffraction and field emission scanning electron microscopy techniques indicate the formation of 3-0 type particulate composites. Coexistence of soft-magnetic behavior and ferroelectric characteristics are confirmed for composites from magnetization vs magnetic field (M–H) and polarization vs electric field (P–E) measurements, respectively. Magneto-dielectric (MD) measurement shows significant changes in the dielectric properties with the application of a magnetic field, indicating the existence of strong MD behavior. The biquadratic nature of magneto-electric (ME) coupling is described by the Landau free energy equation arising from the strain transfer at the interfaces between the constituent phases. The direct magneto-electric voltage coefficient measurement also confirms very strong coupling between ferroelectricity and magnetism and supports the strain-mediated magneto-electric effect in composites. The Φ = 0.3 composite exhibits the maximum ME coefficient of 20.72 mV/cm Oe with M S = 24.62 emu/g, H C = 59.66 Oe, and piezoelectric coefficient value d 33 = 19 pC/N. In conclusion, the strong magneto-electric effect along with low dielectric loss at room temperature in these composites suggests their suitability for multifunctional magneto-electric device applications such as magnetic sensors, etc.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Syntheses and Characterization of Intermetallic Nanostructures Based on Mn

The nanocrystalline powders of Mn50Ni41Sn9 were prepared by ball milling using a PM 200-type RETSCH planetary ball mill. The morphological, microstructural, and structural characterizations of the nanostructured powders were carried out by scanning electron microscope, x-ray diffraction, first using the Williamson–Hall relation for the refinement of the diffraction peak profiles. The high-temperature thermal and magnetic properties of nanocrystalline alloy Mn50Ni41Sn9 were characterized at different temperatures using a vibrating sample magnetometer; differential scanning calorimetry was used to determine the transformation temperature and thermodynamic values in the Mn50Ni41Sn9 alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Investigation of Polypropylene-Montmorillonite Clay Nanocomposite Films Containing a Pro-degradant Additive

This paper investigates the performance of polypropylene (PP) incorporated with montmorillonite (MMT) nanoclay, maleic anhydride grafted PP (PP-g-MAH), and pro-degradant additive (TDPA®), which provides additional benefits of increasing biodegradability. A twin-screw extruder was used to compound PP, MMT, PP-g-MAH, and TDPA, and the extruded nanocomposite films were collected for testing, and their mechanical, thermal, barrier, oxo-biodegradability, and morphological properties were evaluated. Tensile test, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), oxygen permeability test, soil burial test, X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscope (SEM) analysis were used to investigate these properties. Increasing MMT content from 1 to 3 phr increases tensile strength and Young’s modulus of the neat PP samples up to ca.45% and 27% respectively. Improvement of thermal properties for neat PP samples was observed by increasing MMT content from 1 to 3 phr. However, at 4 phr MMT content, both mechanical and thermal properties of nanocomposites dropped slightly. For soil buried samples, DSC and TGA results revealed significant changes in the thermal properties for PP samples containing TDPE additive compared to neat PP, clearly confirming the effectiveness of this TDPA additive in promoting oxo-biodegradation process of PP. Similarly weight loss evaluation result shows that about 4% weight loss for sample (PP/TD), which is PP and TDPA blend only, compared to neat PP. However, increasing MMT content from 1 to 4 phr slightly reduced weight loss of PP from 3.5 to 1.5%, respectively, for 6 month soil exposure period, which indicates that increasing MMT content was detrimental to the degradation process. For higher MMT content, the oxygen permeability of PP nanocomposites was decreased by 46% of the corresponding values for neat PP. The XRD and TEM results confirmed the exfoliation structure of the nanocomposites. The morphological change after soil burial test was studied using scanning electron microscopy (SEM).

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2015

Low-temperature growth of low friction wear-resistant amorphous carbon nitride thin films by mid-frequency, high power impulse, and direct current magnetron sputtering

The potential of different magnetron sputtering techniques for the synthesis of low friction and wear resistant amorphous carbon nitride (a-CN{sub x}) thin films onto temperature-sensitive AISI52100 bearing steel, but also Si(001) substrates was studied. Hence, a substrate temperature of 150 °C was chosen for the film synthesis. The a-CN{sub x} films were deposited using mid-frequency magnetron sputtering (MFMS) with an MF bias voltage, high power impulse magnetron sputtering (HiPIMS) with a synchronized HiPIMS bias voltage, and direct current magnetron sputtering (DCMS) with a DC bias voltage. The films were deposited using a N{sub 2}/Ar flow ratio of 0.16 at the total pressure of 400 mPa. The negative bias voltage, V{sub s}, was varied from 20 to 120 V in each of the three deposition modes. The microstructure of the films was characterized by high-resolution transmission electron microscopy and selected area electron diffraction, while the film morphology was investigated by scanning electron microscopy. All films possessed an amorphous microstructure, while the film morphology changed with the bias voltage. Layers grown applying the lowest substrate bias of 20 V exhibited pronounced intercolumnar porosity, independent of the sputter technique. Voids closed and dense films are formed at V{sub s} ≥ 60 V, V{sub s} ≥ 100 V, and V{sub s} = 120 V for MFMS, DCMS, and HiPIMS, respectively. X-ray photoelectron spectroscopy revealed that the nitrogen-to-carbon ratio, N/C, of the films ranged between 0.2 and 0.24. Elastic recoil detection analysis showed that Ar content varied between 0 and 0.8 at. % and increased as a function of V{sub s} for all deposition techniques. All films exhibited compressive residual stress, σ, which depends on the growth method; HiPIMS produces the least stressed films with values ranging between −0.4 and −1.2 GPa for all V{sub s}, while CN{sub x} films deposited by MFMS showed residual stresses up to −4.2 GPa. Nanoindentation showed a significant increase in film hardness and reduced elastic modulus with increasing V{sub s} for all techniques. The harder films were produced by MFMS with hardness as high as 25 GPa. Low friction coefficients, between 0.05 and 0.06, were recorded for all films. Furthermore, CN{sub x} films produced by MFMS and DCMS at V{sub s} = 100 and 120 V presented a high wear resistance with wear coefficients of k ≤ 2.3 × 10{sup −5} mm{sup 3}/Nm. While all CN{sub x} films exhibit low friction, wear depends strongly on the structural and mechanical characteristics of the films. The MFMS mode is best suited for the production of hard CN{sub x} films, although high compressive stresses challenge the application on steel substrates. Films grown in HiPIMS mode provide adequate adhesion due to low residual stress values, at the expense of lower film hardness. Thus, a relatively wide mechanical property envelope is presented for CN{sub x} films, which is relevant for the optimization of CN{sub x} film properties intended to be applied as low friction and wear resistant coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Growth and structure of alpha-Ta films for quantum circuit integration

Tantalum films incorporated into superconducting circuits have exhibited low surface losses, resulting in long-lived qubit states. The remaining loss pathways originate in microscopic defects that manifest as two level systems (TLSs) at low temperatures. These defects limit performance, so careful attention to tantalum film structures is critical for optimal use in quantum devices. In this work, we investigate the growth of tantalum using magnetron sputtering on sapphire, Si, and photoresist substrates. In the case of sapphire, we present procedures for the growth of fully-oriented films with α-Ta [1 1 1]//Al2O3 [0 0 0 1] and α-Ta [1 −1 0]//Al2O3 [1 0 −1 0] orientational relationships and having residual resistivity ratio (RRR) ∼ 60 for 220 nm thick films. On Si, we find a complex grain texturing with Ta [1 1 0] normal to the substrate and RRR ∼ 30. We further demonstrate airbridge fabrication using Nb to nucleate α-Ta on photoresist surfaces. For the films on sapphire, resonators show TLS-limited quality factors of 1.3 ± 0.3 × 106 at 10 mK (for a waveguide gap and conductor width of 3 and 6 μm, respectively). Structural characterization using scanning electron microscopy, x-ray diffraction, low temperature transport, secondary ion mass spectrometry, and transmission electron microscopy reveal the dependence of residual impurities and screw dislocation density on processing conditions. The results provide practical insights into the fabrication of advanced superconducting devices including qubit arrays and guide future works on crystallographically deterministic qubit fabrication.

42 ENGINEERING↗
DOE OSTI2018

Synthesis of well-dispersed TiO2/CNTs@CoFe2O4 nanocomposites and their photocatalytic properties

Highlights: • Cobalt ferrite microsphere were successfully prepared by using hydrothermal method. • Core/shell structured CNTs@CoFe{sub 2}O{sub 4} composites were prepared using CVD technique with CoFe{sub 2}O{sub 4} microspheres as catalysts. • TiO{sub 2}/CNTs@CoFe{sub 2}O{sub 4} nanocomposites were successfully prepared using CNTs@CoFe{sub 2}O{sub 4} composites as supports. • TiO{sub 2}/CNTs@CoFe{sub 2}O{sub 4} composites show better photo catalytic activities than pure TiO{sub 2}. - Abstract: In this work, core/shell structured CNTs@CoFe{sub 2}O{sub 4} composites were prepared using CVD technique with CoFe{sub 2}O{sub 4} microspheres as catalysts. Titanium dioxide (TiO{sub 2}) was successfully loaded on the surface of CNTs@CoFe{sub 2}O{sub 4} composites to get TiO{sub 2}/CNTs@CoFe{sub 2}O{sub 4} nanocomposites. As-prepared nanocomposites were examined by scanning electron microscopy, X-ray diffraction and transmission electron microscopy. The results show a successful loading of TiO{sub 2} nanoparticles on CNTs@CoFe{sub 2}O{sub 4} composites. The photocatalytic properties of TiO{sub 2}/CNTs@CoFe{sub 2}O{sub 4} nanocomposites for methylene blue were investigated under UV light irradiation. The degradation rate of methylene blue is 96% for TiO{sub 2}/CNTs@CoFe{sub 2}O{sub 4} nanocomposites with TiO{sub 2} mass ratio of 68.4%, while it is 71% for pure TiO{sub 2}. CNTs play a key role in the charge recombination to enhance the electron hole separation. CoFe{sub 2}O{sub 4} is beneficial for the recyclability of the composite catalysts by providing a magnetic field.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2019

Ag-doped HfO{sub 2} thin films via sol–gel dip coating method

In this study, undoped and Ag-doped HfO{sub 2} thin films were deposited on glass substrates by means of sol–gel dip coating method. These films were then thermally annealed at 500 °C for 1 h. The structural and optical properties of undoped and Ag-doped HfO{sub 2} thin films were characterized by X-ray diffraction, UV–Vis spectrometry and scanning electron microscope. The results of this analysis were compared and interpreted with the results obtained in literature by various methods of coating with HfO{sub 2}. The X-ray diffraction peaks of the films paired with monoclinic HfO{sub 2} crystalline peaks. The refractive indices of the films decreased with doping Ag, at 500 nm wavelengths. The optical band gap values of Ag-doped HfO{sub 2} thin films increased with doping Ag. The porous structures were observed on the surface films, especially with 5% Ag doping.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Postshock Thermally Induced Transformations in Experimentally Shocked Magnetite

We studied the effect of 973 K heating in argon atmosphere on the magnetic and structural properties of a magnetite-bearing ore, which was previously exposed to laboratory shock waves between 5 and 30 GPa. For this purpose magnetic properties were studied using temperature-dependent magnetic susceptibility, magnetic hysteresis and low-temperature saturation isothermal remanent magnetization. Structural properties of magnetite were analyzed using X-ray diffraction, high-resolution scanning electron microscopy and synchrotron-assisted X-ray absorption spectroscopy. The shock-induced changes include magnetic domain size reduction due to brittle and ductile deformation features and an increase in Verwey transition temperature due to lattice distortion. After heating, the crystal lattice is relaxed and apparent crystallite size is increased suggesting a recovery of lattice defects documented by a mosaic recrystallization texture. The structural changes correlate with modifications in magnetic domain state recorded by temperature-dependent magnetic susceptibility, hysteresis properties and low-temperature saturation isothermal remanent magnetization. In conclusion, these alterations in both, magnetic and structural properties of magnetite can be used to assess impact-related magnetic anomalies in impact structures with a high temperature overprint.

58 GEOSCIENCES↗