Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diameter effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Enhancement of thermoelectric performance in InAs nanotubes by tuning quantum confinement effect

By using the nonequilibrium Green's function method, we study the thermoelectric properties of InAs nanotubes. The results show that InAs nanotube with a certain internal diameter has much higher ZT value than nanowire due to the enhancement of quantum confinement effect leading to the increase of the power factor S{sup 2}G. The ZT value of InAs nanotube can reach 1.74, which is about three times greater than that of nanowires. Moreover, it is found that the ZT values of InAs nanotubes decrease rapidly with the increase of internal diameter, which results from the rapid increase of phonons thermal conductance due to the “red shift” of low-frequency optical phonon modes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Customizing electron confinement in plasma-assembled Si/AlN nanodots for solar cell applications

Size-uniform Si nanodots (NDs) are synthesized on an AlN buffer layer at low Si(111) substrate temperatures using inductively coupled plasma-assisted magnetron sputtering deposition. High-resolution electron microscopy reveals that the sizes of the Si NDs range from 9 to 30 nm. Room-temperature photoluminescence (PL) spectra indicate that the energy peak shifts from 738 to 778 nm with increasing the ND size. In this system, the quantum confinement effect is fairly strong even for relatively large (up to 25 nm in diameter) NDs, which is promising for the development of the next-generation all-Si tandem solar cells capable of effectively capturing sunlight photons with the energies between 1.7 (infrared: large NDs) and 3.4 eV (ultraviolet: small NDs). The strength of the resulting electron confinement in the Si/AlN ND system is evaluated and justified by analyzing the measured PL spectra using the ionization energy theory approximation.

36 MATERIALS SCIENCE↗

Solid particulate mass and number from ducted fuel injection in an optically accessible diesel engine in skip-fired operation

Ducted fuel injection (DFI) is a new combustion strategy that has been shown to significantly attenuate soot formation in diesel engines. While previous studies have used optical diagnostics and optical filter smoke number methods to show that DFI reduces in-cylinder soot formation and engine-out soot emissions, respectively, this is the first study to measure solid particle number (PN) emissions in addition to particle mass (PM). Furthermore, this study quantitatively evaluates the use of transient particle instruments for measuring particles from skip-fired operation in an optical single cylinder research engine (SCRE). Engine-out PN was measured using an engine exhaust particle sizer following a catalytic stripper, and PM was measured using a photoacoustic analyzer. The study improves on earlier preliminary emissions studies by clearly showing that DFI reduces overall PM by 76%–79% and PN for particles larger than 23 nm by 77% relative to conventional diesel combustion at a 1200-rpm, 13.3-bar gross indicated mean effective pressure operating condition. The degree of engine-out PM reduction with DFI was similar across both particulate measurement instruments used in the work. Through the use of bimodal distribution fitting, DFI was also shown to reduce the geometric mean diameter of accumulation mode particles by 26%, similar to the effects of increased injection pressure in conventional diesel combustion systems. This work clearly shows the significant solid particulate matter reductions enabled by DFI while also demonstrating that engine-out PN can be accurately measured from an optical SCRE operating in a skip-fired mode. Based on these results, it is believed that DFI has the potential to enable fuel savings when implemented in multi-cylinder engines, both by lowering the required frequency of active diesel particulate filter regeneration, and by reducing the backpressure imposed by exhaust filtration systems.

33 ADVANCED PROPULSION SYSTEMS↗

Monte Carlo Simulation of a Knudsen Effusion Mass Spectrometer Sampling System

Knudsen flow is easily simulated with a Monte Carlo method. In this study we develop a Visual Basic for Excel (VBA) code to simulate the molecular beam from a vaporizing solid. The system at NASA Glenn uses the restricted collimation method of Chatillon and colleagues, which consists of two apertures between the effusion cell and the ionizer. The diameter of the first aperture is smaller than the diameter of the effusion cell orifice, so the ionizer effectively only sees inside the effusion cell. The code is able to calculate the transmission coefficient through the cell orifice, through the cell orifice and the first aperture, and through the cell orifice and first and second aperatures. Calculated transmission coefficients through the cell orifice are compared to tabulated values to validate the code. Then transmission coefficients are calculated through the cell orifice and both apertures to the ionizer. This allows the geometry (aperture spacing and diameters) of the sampling system the sampling system to be optimized. Calculated transmission factors are also compared to literature values calculated via an analytic method.

Radke, Michael J.↗

Summary of model VTOL lift fan tests conducted at NASA Lewis Research Center

The purpose of the tests was to obtain overall performance and influencing factors as well as detailed measurements of the internal flow characteristics. The first experiment consisted of crossflow tests of a 15-inch diameter fan installed in a two-dimensional wing. Tests were run with and without exit louvers over a range of tunnel speeds, fan speeds, and wing angle of attack. The wing was used for a study of installation effects on lift fan performance. The model tested consisted of three 5.5-inch diameter tip-turbine driven model VTOL lift fans mounted chord-wise in the two-dimensional wing to simulate a pod-type array. Several inlet and exit cover door configurations and an adjacent fuselage panel were tested. For the third program, a pod was attached to the wing, and an investigation was conducted of the effect of design tip speed on the aerodynamic performance and noise of a 15-inch diameter lift fan-in-pod under static and crossflow conditions. Three single VTOL lift fan stages were designed for the same overall total pressure ratio but at three different rotor tip speeds.

Diedrich, J. H.↗

Effect of Sample Thickness on the Tensile Strength of Small Graphite Discs

This report formally documents the completion of the Advanced Reactor Technologies (ART) Level 3 Milestone (M3TG-24OR0501054), “Continue activities related to Split Disc-DIC - complete analysis of effect of sample thickness on one fine grain graphite,” due May 31, 2024. Details within this report outline the status of activities aimed at elucidating the effect of sample thickness on the tensile strength measurement using the small-disc, split-disc testing standard in support of the US Department of Energy’s ART Graphite R&D Program. The ASTM D8289, Standard Test Method for Tensile Strength Estimate by Disc Compression of Manufactured Graphite, was developed to provide an alternative means for testing tensile strength on smaller specimens, which are compatible with available irradiation capsule volumes, and other compatibility measurements. ASTM D8289 specifies that acceptable specimen diameter can range from 6 to 12.7 mm and that the maximum allowed sample thickness should be half of the diameter. However, information is limited with respect to the effect of thickness on the measured splitting tensile strength. This report documents efforts to understand the effect of sample thickness on splitting tensile strength. The work involved testing Ø12.7 mm samples of fine-grain graphites 2114 and IG-110 of different thicknesses (6.35, 5, 4, and 3 mm). The digital image correlation (DIC) method was applied to the samples, along with the ASTM D8289 Standard, to help interpret the measured results.

36 MATERIALS SCIENCE↗

Effects of Reynolds number on orifice induced pressure error

Data previously reported for orifice induced pressure errors are extended to the case of higher Reynolds number flows, and a remedy is presented in the form of a porous metal plug for the orifice. Test orifices with apertures 0.330, 0.660, and 1.321 cm in diam. were fabricated on a flat plate for trials in the NASA Langley wind tunnel at Mach numbers 0.40-0.72. A boundary layer survey rake was also mounted on the flat plate to allow measurement of the total boundary layer pressures at the orifices. At the high Reynolds number flows studied, the orifice induced pressure error was found to be a function of the ratio of the orifice diameter to the boundary layer thickness. The error was effectively eliminated by the insertion of a porous metal disc set flush with the orifice outside surface.

Plentovich, E. B.↗

Yarkovsky Drift Detections for 247 Near-Earth Asteroids

The Yarkovsky effect is a thermal process acting upon the orbits of small celestial bodies, which can cause these orbits to slowly expand or contract with time. The effect is subtle (〈da/dt〉∼10{sup −4} au My{sup −1} for a 1 km diameter object) and is thus generally difficult to measure. We analyzed both optical and radar astrometry for 600 Near-Earth Asteroids (NEAs) for the purpose of detecting and quantifying the Yarkovsky effect. We present 247 NEAs with measured drift rates, which is the largest published set of Yarkovsky detections. This large sample size provides an opportunity to examine the Yarkovsky effect in a statistical manner. In particular, we describe two independent population-based tests that verify the measurement of Yarkovsky orbital drift. First, we provide observational confirmation for the Yarkovsky effect’s theoretical size dependence of 1/D, where D is diameter. Second, we find that the observed ratio of negative to positive drift rates in our sample is 2.34, which, accounting for bias and sampling uncertainty, implies an actual ratio of 2.7{sub −0.7}{sup +0.3}. This ratio has a vanishingly small probability of occurring due to chance or statistical noise. The observed ratio of retrograde to prograde rotators is two times lower than the ratio expected from numerical predictions from NEA population studies and traditional assumptions about the sense of rotation of NEAs originating from various main belt escape routes. We also examine the efficiency with which solar energy is converted into orbital energy and find a median efficiency in our sample of 12%. We interpret this efficiency in terms of NEA spin and thermal properties.

79 ASTRONOMY AND ASTROPHYSICS↗

Selection effects against small comets

Everhart's (1967) formulation is used to determine the correlation between the probability of discovering a comet and the size of its nuclear radius. The analysis is concentrated on comets that are not more than two or three hundred meters in diameter; hence, heliocentric variations in cometary brightness can be neglected. The effect of cometary physical decay is also considered, and a strong observational bias against the detection of small active comets is found. The following three factors are involved: (1) small comets must pass closer to the earth than large comets in order to be detected, (2) the resulting higher angular velocity for nearby comets leads to a decrease in the time available to discover a small comet, and (3) small comets physically decay and vanish faster than do large comets.

Zook, H. A.↗

Free-Spinning-Tunnel Investigation of a 1/24-Scale Model of the Grumman F9F-6 Airplane TED No. NACA DE 364

An investigation of a 1/24-scale model of the Grumman F9F-6 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The erect and inverted spin and recovery characteristics of the model were determined for the normal flight loading with the model in the clean condition. The effect of loading variations was investigated briefly. Spin-recovery parachute tests were also performed. The results indicate that erect spins obtained on the airplane in the clean condition will be satisfactorily terminated for all loading conditions provided full rudder reversal is accompanied by moving the ailerons and flaperons (lateral controls) to full with the spin (stick right in a right spin). Inverted spins should be satisfactorily terminated by full reversal of the rudder alone. The model tests indicate that an 11.4-foot (laid-out-flat diameter) tail parachute (drag coefficient approximately 0.73) should be effective as an emergency spin-recovery device during demonstration spins of the airplane provided the towline is attached above the horizontal stabilizer.

Klinar, Walter J.↗

Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Mission Overview and Science Return

The Low-Earth Orbit (LEO) Flight Test of an Inflatable Decelerator (LOFTID) mission was the culmination of two decades of research and development led by NASA Langley Research Center for Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology. A HIAD aeroshell can be hard packed into a small volume for launch and then deployed prior to atmospheric entry for stable aerodynamic deceleration through the atmosphere. Much larger than traditional fixed diameter aeroshells that are constrained by the size of launch vehicle shrouds, inflatable decelerators create more drag and start the deceleration process in the upper reaches of the atmosphere with greater efficiency and stability. Large deployable heatshields enable spacecraft to carry bigger, heavier payloads, including scientific instruments and human support systems for planetary landing and exploration. The success of the LOFTID mission could enable new NASA missions to Mars (including access to higher altitudes than currently possible), Venus, and most solar system destinations with atmospheres, as well as cost-effective payload returns to Earth. With its unique 6m diameter inflatable heatshield, LOFTID was the first-of-a-kind orbital reentry flight, and the largest blunt body atmospheric entry of any kind. On November 10, 2022, the LOFTID aeroshell endured the harsh environments of atmospheric reentry while exhibiting stable aerodynamics through the entire spectrum of hypersonic, supersonic, transonic, and subsonic flight. The demonstration confirmed the HIAD technology structural and thermal performance as the aeroshell protected the 1100 kg Reentry Vehicle (RV) entering Earth’s atmosphere at 8 km/s, reaching Mach 30, and experiencing 9.5 g deceleration before deploying parachutes and gently splashing down in the Pacific Ocean, where it was recovered in excellent condition. The LOFTID aeroshell was exposed to an aeroheating environment representative of many Mars and LEO HIAD applications, and successfully demonstrated the ability of the heat-affected inflatable structure to withstand aerodynamic forces that exceeded those expected at Mars. This mission further demonstrated the viability of HIAD technology to deliver large payloads safely and accurately through an atmosphere via a controlled entry, descent, and landing. Whereas LOFTID was indeed a first-of-a-kind flight for an inflatable heatshield, its remarkable performance assured that it will not be the last of its kind.

J M Dinonno↗

Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Mission Overview and Science Return

The Low-Earth Orbit (LEO) Flight Test of an Inflatable Decelerator (LOFTID) mission was the culmination of two decades of research and development led by NASA Langley Research Center for Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology. A HIAD aeroshell can be hard packed into a small volume for launch and then deployed prior to atmospheric entry for stable aerodynamic deceleration through the atmosphere. Much larger than traditional fixed diameter aeroshells that are constrained by the size of launch vehicle shrouds, inflatable decelerators create more drag and start the deceleration process in the upper reaches of the atmosphere with greater efficiency and stability. Large deployable heatshields enable spacecraft to carry bigger, heavier payloads, including scientific instruments and human support systems for planetary landing and exploration. The success of the LOFTID mission could enable new NASA missions to Mars (including access to higher altitudes than currently possible), Venus, and most solar system destinations with atmospheres, as well as cost-effective payload returns to Earth. With its unique 6m diameter inflatable heatshield, LOFTID was the first-of-a-kind orbital reentry flight, and the largest blunt body atmospheric entry of any kind. On November 10, 2022, the LOFTID aeroshell endured the harsh environments of atmospheric reentry while exhibiting stable aerodynamics through the entire spectrum of hypersonic, supersonic, transonic, and subsonic flight. The demonstration confirmed the HIAD technology structural and thermal performance as the aeroshell protected the 1100 kg Reentry Vehicle (RV) entering Earth’s atmosphere at 8 km/s, reaching Mach 30, and experiencing 9.5 g deceleration before deploying parachutes and gently splashing down in the Pacific Ocean, where it was recovered in excellent condition. The LOFTID aeroshell was exposed to an aeroheating environment representative of many Mars and LEO HIAD applications, and successfully demonstrated the ability of the heat-affected inflatable structure to withstand aerodynamic forces that exceeded those expected at Mars. This mission further demonstrated the viability of HIAD technology to deliver large payloads safely and accurately through an atmosphere via a controlled entry, descent, and landing. Whereas LOFTID was indeed a first-of-a-kind flight for an inflatable heatshield, its remarkable performance assured that it will not be the last of its kind.

John M DiNonno↗

Analysis of the effects of fuel spray characteristics on NO(x) formation

Results from experimental and analytical studies on NO(x) formation in a one-dimensional monodisperse spray combustion system are reported. In a previous investigation, an optimum droplet diameter was reported for minimizing NO(x) emissions. In this paper, the effects of enhanced prevaporization and droplet interactions in addition to droplet size effects on NO(x) formation are investigated by air preheating experiments. These phenomena have been incorporated into an analytical model which predicts NO(x) formed from the combustion of monodisperse fuel sprays. Both, experimental and computed results indicate the importance of the extent of prevaporization and droplet interactions on NO(x) production. Preflame vaporization controls the gas phase stoichiometry which has a significant effect on the volume of the hot gases surrounding a fuel droplet where NO(x) is formed. On the other hand, the release of fuel vapor from the droplet to the reaction zone is influenced by droplet interactions which reduce the volume of the hot gases and NO(x) production by bringing the flame closer to the droplet surface.

Sarv, H.↗

Plasmon-enhanced photocurrent of Ge-doped InGaO thin film transistors using silver nanoparticles

Germanium-doped indium-gallium oxide (GIGO) thin film transistors (TFTs) decorated with silver (Ag) nanoparticles (NPs) were prepared to study the plasmon effect. GIGO films of various thicknesses were deposited on SiO{sub 2}/Si substrates, and Ag NPs (∼25 nm in diameter) were formed using a thermal evaporator and a postannealing process. The Ag NPs effectively absorbed light in the wavelength range of 500 and 600 nm, which corresponds to the plasmonic effect. Due to the plasmon resonance of Ag NPs, a significantly enhanced photocurrent was observed on the devices. The current increased by 348% with exposure to light when the Ag NPs were formed at the interface between the 10-nm-thick GIGO film and SiO{sub 2} substrate. The increased photocurrent revealed the presence of strong coupling between the localized plasmon and electrical carrier of the devices. The results show that the photocurrent of GIGO TFTs can be greatly enhanced when the plasmonic Ag NPs are located in the channel region of the devices.

36 MATERIALS SCIENCE↗

Rotordynamic coefficients for compressible flow in tapered annular seals

Derivation of the governing equations for compressible flow in a tapered annular seal is based on Hirs' turbulent bulk-flow model. Zeroth and first-order perturbation equations are developed by an expansion in the eccentricity ratio. These equations are numerically integrated to obtain the leakage, and the direct and cross-coupled stiffness and damping coefficients. Seal parameters similar to the Space Shuttle Main Engine High Pressure Oxidizer Turbopump are used to demonstrate output from the analysis procedure. The effects of preswirl and seal taper are shown for three different length-to-diameter ratios. Generally the results indicate that prerotating the fluid significantly increases the cross-coupled stiffness but has little effect on the other coefficients, and increasing the convergent taper increases the direct stiffness while decreasing the direct damping and cross-coupled stiffness.

Nelson, C. C.↗

Multiphase Large Eddy Simulation of a Pulsed Sieve-Plate Extraction Column - 18125

Presented here is research resulting from a framework of single-phase and multiphase modelling trials. These are intended to accurately simulate the internal flow phenomena arising in pulsed sieve-plate extraction columns representative of those found in industry. Three-dimensional unsteady flow calculations using large eddy simulation coupled with dynamic sub-grid scale modelling have been used to capture the transient effects of sinusoidal flow conditions using the open source CFD code OpenFOAM{sup R}. Multiphase interface interactions are modelled using the volume of fluid method with appropriate heavy and light phase fluidic properties capturing surface tension, density and viscous effects. The system studied consists of a 150 mm diameter column with two perforated plates with a fractional free area of 25 %, operational under 1 Hz pulsing frequency at a 50 mm amplitude and plate spacing of 300 mm. The materials simulated include water (single-phase) and 3 M nitric acid and dodecane / tributyl phosphate mixture at 30 vol% (multiphase). Results are compared with appropriate correlations from literature. The dispersive mixing efficiency of the system was also evaluated via a mixing index value which allows quantification of the ratio of rotational and irrotational flow components. This study has found that the predictive methods employed are effective at capturing the different scales of turbulence present within pulsed sieve-plate extraction columns, and its influence on their operation. As such, the work highlights the ability of large eddy simulation-based modelling to predict the complex flows in such column geometries. Furthermore, the techniques employed provide valuable insight into the hydrodynamic flow characteristics and mixing mechanisms arising within pulsed sieve-plate extraction columns. (authors)

42 ENGINEERING↗

A hollow cathode neutralizer for a 30-cm diameter bombardment thruster

Recent improvements in overall thruster performance have imposed new constraints on neutralizer performance. The use of compensated grid extraction system requires a reevaluation of neutralizer position. A series of tests were conducted to determine what effect neutralizer cathode geometry has on performance. The parameters investigated included orifice diameter and length, and cathode diameter. Similar tests investigated open and enclosed keeper geometries. Neutralizer position tests with compensated grids suggested positions approximately 10 cm from the accelerator and radially out of the beam envelope should result in satisfactory performance and long life. Operation at keeper current of 1.5 am resulted in lower total neutralizer power, the elimination of tip heater power, and suitable closed loop control of the neutralizer vaporizer.

Bechtel, R. T.↗

Effect of variable inlet guide vanes on the operating characteristics of a tilt nacelle inlet/powered fan model

The effects of a variable inlet guide vane (VIGV) assembly on the operating characteristics of a V/STOL inlet and on the performance of a 20-in. (0.508-m) diameter fan engine were investigated. The data indicate that the VIGVs are effective thrust modulators over a wide range of free-stream velocities, nacelle angles of attack, and fan speeds. The thrust modulation ranges, including choking limits, fan stall limits, and inlet separation boundaries are presented. The presence of the VIGV assembly causes significant losses in inlet angle-of-attack capability and generally increases the blade stress levels at all limit conditions except at high angle of attack and high free-stream velocity. Reducing the fan nozzle exit area limited the positive VIGV actuation range and consequently decreased the range of thrust modulation at all limit conditions except at both high free-stream velocity and high angle of attack conditions.

Woollett, R. R.↗