Search NASA⌕ Search

SEARCH · Search NASA

Results for “X ray diffraction analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

In Situ Cs and H Exchange into Gaidonnayite and Proposed Mechanisms of Ion Diffusion

Here, the microporous mineral gaidonnayite Na 2 ZrSi 3 O 9 ·2H 2 O was studied to better understand its ion-exchange mechanisms, specifically for Cs + and H + ions. In situ Raman spectroscopy, in situ X-ray diffraction (XRD), simultaneous thermogravimetric analysis and differential scanning calorimetry (TGA/DSC), and in situ X-ray fluorescence were used to determine the exchange processes involved. The Raman spectra contain strong peaks that can be attributed to the vibrational modes for the 3MR symmetric stretch at 500 cm –1 , Si–O–Zr–O chain stretches at 938 cm –1 , and Si–O stretching in the 1000–1100 cm –1 range. The most prominent Raman shift during ion exchange is found near the 520 cm –1 peak, which corresponds to distortions of the 3MR substructure of gaidonnayite. In all instances of this study, the 3MR exhibited the highest amount of distortion during ion exchange, and the evolution of this distortion is compared to unit-cell changes as measured from XRD data and elemental changes via XRF. The correlations between the Raman, XRD, and XRF data show rapid deformation of the 3MR during the onset of H + ion exchange in the Na form of gaidonnayite. Even when unit-cell volume changes were small (<3 Å 3 ) as in the cases for Cs + into Na-gaidonnayite and Cs + into H-gaidonnayite, significant changes in the ≈520 cm –1 peak were measured. By comparing XRD data and Raman data, and verifying the cation uptake by XRF, we were able to identify and confirm conformational changes and distortions in the crystal structure before, during, and after Cs + and H + exchange. Finally, Cs exchange occurred the fastest and with the greatest capacity when starting in the H-form at room temperature, and at elevated temperatures when starting in the Na-form.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Application of E{sub h}-pH diagram for room temperature precipitation of zinc stannate microcubes in an aqueous media

Graphical abstract: - Highlights: • One pot aqueous synthesis of zinc stannate (ZnSnO{sub 3}) particles at low temperature. • Synthesis designed with the assistance of potential-pH diagram. • ZnSnO{sub 3} estimated to be stable between pH 8 and 12 was used for synthesis of the particles. • ZnSnO{sub 3}·3H{sub 2}O were formed during the precipitation of zinc stannate. - Abstract: Potential-pH diagram assisted-design for controlled precipitation is an attractive method to obtain engineered binary and ternary oxide particles. Aqueous synthesis conditions of zinc stannate (ZnSnO{sub 3}) particles at low temperature were formulated with the assistance of potential-pH diagram. The pH of a solution containing stoichiometric amounts of Zn{sup 2+} and Sn{sup 4+} was controlled for the precipitation in a one pot synthesis step at room temperature (25 °C). The effect of the concentration of the reactants on the particle size was studied by varying the concentration of the precursor (Zn{sup 2+} + Sn{sup 4+}) solution. Scanning electron micrographs show that the particles are monodispersed micron sized cubes formed by the self-organization of nano-sized crystallites. The obtained microcubes characterized by X-ray Diffraction and thermo gravimetric analysis (TGA) show that the particles are in ZnSnO{sub 3}·3H{sub 2}O form.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Synthesis and characterization of pharmaceutical surfactant templated mesoporous silica: Its application to controlled delivery of duloxetine

Graphical abstract: - Highlights: • Usefulness of dual pharmaceutical surfactants in silica synthesis was evaluated. • Effects of concentration of secondary template (Tween-40) were studied. • Effects of fixed solvothermal condition on mesostructure formation were studied. • Duloxetine drug loading capability was studied. • Sustained release of duloxetine was evaluated. - Abstract: A new group of mesoporous silica nanoparticles (MSNs) were synthesized using combination pharmaceutical surfactants, Triton X-100 and Tween-40 as template and loaded with duloxetine hydrochloride (DX), for improving the sustained release of DX and patterns with high drug loading. Agglomerated spherical silica MSNs were synthesized by sol–gel and solvothermal methods. The calcined and drug loaded MSNs were characterized using X-ray diffraction (XRD), Braunner–Emmett–Teller (BET), thermogravimetric analysis (TGA), Fourier-transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), diffuse reflectance ultraviolet–visible (DRS-UV–vis) spectroscopy. MSNs with high surface area and pore volume were selected and studied for their DX loading and release. The selected MSNs can accommodate a maximum of 34% DX within it. About 90% was released at 200 h and hence, the synthesized MSNs were capable of engulfing DX and sustain its release. Further form the Ritger and Peppas, Higuchi model for mechanism drug release from all the MSN matrices follows anomalous transport or Non-Fickian diffusion with the ‘r’ and ‘n’ value 0.9 and 0.45 < n < 1, respectively. So, from this study it could be concluded that the MSNs synthesized using pharmaceutical templates were better choice of reservoir for the controlled delivery of drug which requires sustained release.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Influence of sodium dodecyl sulfate concentration on the photocatalytic activity and dielectric properties of intercalated sodium dodecyl sulfate into Zn–Cd–Al layered double hydroxide

Highlights: • Zn–Cd–Al–LDH–DS were synthesized with different SDS concentrations. • Photocatalytic activity of samples was improved by increasing SDS concentration. • Dielectric response of LDH can be described by anomalous low frequency dispersion. • The dc conductivity values were calculated for Zn–Cd–Al–LDH–DS samples. • ESR spectra exhibited the successful intercalation of DS molecule into LDH gallery. - Abstract: Sodium dodecyl sulfate (SDS) has been successfully intercalated into Zn–Cd–Al–LDH precursor with different SDS concentrations (0.2, 0.3, 0.4, 0.5 and 1 mol L{sup −1}) using the coprecipitation method at (Zn{sup 2+} + Cd{sup 2+})/Al{sup 3+} molar ratio of 13 and pH 8. The structural, morphological, texture and composition properties of the synthesized (Zn–Cd–Al–LDH–DS) nanostructure were investigated using powder X-ray diffraction (PXRD), scanning electron microscope (SEM), thermogravimetric analysis (TGA) and Fourier transform infrared (FT-IR), respectively. The photocatalytic activity of these materials was developed by increasing the concentration of intercalated SDS. The absorbance spectra have been used to detect an anion in the LDH interlayer before and after the intercalation process, which confirmed the presence of the dodecyl sulfate (DS{sup −}) anion into LDH gallery after intercalation. The anomalous low frequency dispersion (ALFD) has been used to describe the dielectric response of Zn–Cd–Al–LDH–DS nanostructure using the second type of universal power law. At low frequency, the polarization effect of electrodes caused the rising in dielectric constant and loss values. An important result of the dielectric measurements is the calculated dc conductivity values, which are new in dielectric spectroscopy of LDH materials. An important result of the electron spin resonance (ESR) spectra exhibited the successful intercalation of DS molecule into LDH gallery. The g-factor value was affected by the SDS concentration which indicated changes to the environment around the DS molecule in LDH interlayer.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Cu-PDC-bpa solid coordination frameworks (PDC=2,5-pyrindinedicarboxylate; bpa=1,2-DI(4-pyridil)ethane)): 2D and 3D structural flexibility producing a 3-c herringbone array next to ideal

Combination of polycarboxylate anions and dipyridyl ligands is an effective strategy to produce solid coordination frameworks (SCF) which are crystalline materials based on connections between metal ions through organic ligands. In this context, this work is focused on two novel Cu{sup II}-based SCFs exhibiting PDC (2,5-pyridinedicarboxylate) and bpa (1,2-di(4-pyridyl)ethane), being the first structures reported in literature containing both ligands. Chemical formula are [Cu{sub 2}[(PDC){sub 2}(bpa)(H{sub 2}O){sub 2}]·3H{sub 2}O·DMF (1), and [Cu{sub 2}(PDC){sub 2}(bpa)(H{sub 2}O){sub 2}]·7H{sub 2}O (2), where DMF is dimethylformamide. Compounds 1 and 2 have been characterized by means of X-ray diffraction (XRD), infrared spectroscopy (IR), thermogravimetric (TG) analysis, differential thermal analysis (DTA) and dielectric measurements. The crystallographic analysis revealed that compounds 1 and 2 can be described as herringbone-type layers formed by helicoidal Cu-PDC-Cu chains connected through bpa ligands. Solvent molecules are crystallized between the layers, providing the inter-layer connections through hydrogen bonds. Differences between both compounds are attributable to the flexibility of bpa (in 2D) as well as to the 3D packing of the layers which is solvent dependent. This fact results in the fact that compound 2 is the most regular 3-c herringbone array reported so far. The structural dynamism of these networks is responsible for the crystalline to-amorphous to-crystalline (CAC) transformation from compound 1 to compound 2. Crystallochemical features for both compounds have also been studied and compared to similar 3-connected herringbone-arrays. - Graphical abstract: Cu-PDC-bpa 3-c herringbone arrays. - Highlights: • The most ideal herringbone array reported so far is a Cu-PDC-bpa SCF. • Conformational freedom of bpa results in 2D and 3D flexibility of the SCFs. • The flexibility of the SCFs is related to a phase transformation. • Dielectric measurements confirm the mobility of guest solvent molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Material characteristics and equivalent circuit models of stacked graphene oxide for capacitive humidity sensors

The oxidation properties of graphene oxide (GO) are systematically correlated with their chemical sensing properties. Based on an impedance analysis, the equivalent circuit models of the capacitive sensors are established, and it is demonstrated that capacitive operations are related to the degree of oxidation. This is also confirmed by X-ray diffraction and Raman analysis. Finally, highly sensitive stacked GO sensors are shown to detect humidity in capacitive mode, which can be useful in various applications requiring low power consumption.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Fabrication of hierarchical meso/macroporous TiO2 scaffolds by evaporation-induced self-assembly technique for bone tissue engineering applications

Highlights: • Hierarchical meso/macroporous TiO{sub 2} scaffolds were produced. • TiO{sub 2} formation mechanism was investigated. • The scaffolds had a pore size of 150–300 μm and meso pores of 6–12 nm. • The specific surface area obtained from BET theory was 67.89 m{sup 3} g{sup −1}. - Abstract: This paper reports the synthesis of hierarchical meso/macroporous TiO{sub 2} scaffolds by mimicking bone structure. Evaporation-induced self-assembly (EISA) method along with foamy method was utilized to produce TiO{sub 2} scaffolds in situ. Simultaneous thermal analysis (STA), small angle X-ray diffraction (SAXD), wide-angle X-ray diffraction (WAXD), nitrogen adsorption–desorption isotherm analysis, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques were applied to characterize the scaffolds. The results showed that TiO{sub 2} scaffolds can be produced after sintering the specimens at 550 °C for 2 h. The obtained scaffolds had a pore size in the range of 150–300 μm and meso pores in the range of 6–12 nm. The specific surface area was obtained from the Brunauer–Emmett–Teller theory, the total volume and mean diameter of pores were 67.89 m{sup 3} g{sup −1}, 0.1245 cm{sup 3} g{sup −1} and 7.3 nm, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of Sintering Temperature on Structural, Morphological and Magnetic Properties of Strontium Ferrite Nanoparticles

In the present investigation, structural, morphological and magnetic properties of SrFe{sub 2}O{sub 4} ferrite nanoparticles prepared by a sol–gel method were studied. The techniques used in this investigation were thermogravimetric analysis/differential thermal analysis (TGA/DTA), X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), field emission scanning electron microscopy (FESEM), Fourier transform infrared spectrometry (FT-IR), vibrating sample magnetometry (VSM) and Curie temperature analysis. The average crystallite sizes of the SrFe{sub 2}O{sub 4} were calculated using the Scherrer formula and found in the range of 11–22 nm, and this can be attributed to the grain growth of the particles. The lattice parameter of SrFe{sub 2}O{sub 4} nanoparticles decreased from 6.64 to 6.51 nm as the sintering temperature was raised from 600 to 900 °C. FT-IR analysis confirmed that bands in the range 430–590 cm{sup − 1} are due to the stretching vibration of oxygen atom and metal ions (M–O) that is Fe–O confirming the formation of spinel ferrite. Surface morphology of the samples has been studied using FESEM. The elemental composition along with their relative ratios was given by EDX and was found to be in agreement with their initial calculated values. The saturation magnetization, magnetic coercivity and remanence increase with an increasing sintering temperature from 600 to 900 °C. The present study reports the Curie temperature with an amount of 551 °C of the synthesized strontium nanoferrites using the Faraday technique.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2015

Low-temperature synthesis of homogeneous solid solutions of scheelite-structured Ca 1-x Sr x WO 4 and Sr 1-x Ba x WO 4 nanocrystals

Here, a series of compositionally complex scheelite-structured nanocrystals of the formula A 1-x A’ x WO 4 (A = Ca, Sr, Ba) have been prepared under benign synthesis conditions using the vapor diffusion sol–gel method. Discrete nanocrystals with sub-20 nm mean diameters were obtained after kinetically controlled hydro- lysis and polycondensation at room temperature, followed by composition-dependent thermal aging at or below 60 °C. Rietveld analysis of X-ray diffraction data and Raman spectroscopy verified the synthesis of continuous and phase-pure nanocrystal solid solutions across the entire composition space for A 1-x A’ x WO 4 , where 0 ≤ x ≤ 1. Elemental analysis by X-ray photoelectron and inductively coupled plasma- atomic emission spectroscopies demonstrated excellent agreement between the nominal and experi- mentally determined elemental stoichiometries, while energy dispersive X-ray spectroscopy illustrated good spatial elemental homogeneity within these nanocrystals synthesized under benign conditions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2013

Tropical sea snail shells: Possible exotic sources for ceramic biomaterial synthesis

In this study, chemical and structural properties of sea snail shell based bioceramic materials (i.e. hydroxyapatite, whitlockite and other phases) are produced by using mechano-chemical (ultrasonic) conversion method. For this purpose, differential thermal and gravimetric analysis (DTA/TG), X-ray diffraction, infra-red (IR) and scanning electron microscope (SEM) studies are performed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Two new helical compounds based on Keggin clusters and N-donor multidentate ligand: Syntheses, structures and properties

Two isostructural polyoxometalate-based inorganic–organic hybrids with 1D helical chain, [CuH{sub 3}L{sub 2}(GeMo{sub 12}O{sub 40})]·2H{sub 2}O (1) and [CuH{sub 3}L{sub 2}(SiMo{sub 12}O{sub 40})]·2H{sub 2}O (2), where L=2,4,5-tri(4-pyridyl)-imidazole have been synthesized under hydrothermal conditions. It is the first time to use the L ligand to synthesis the Keggin-type polyoxometalate-based inorganic–organic hybrids. The two compounds possess the left- and right-handed helical chains and the POMs as pendants attach in the helical chains through Cu–O bonds. The two compounds have been characterized by elemental analyses, infrared (IR) spectroscopy, powder X-ray diffraction (PXRD), X-ray photoelectron spectra (XPS), thermogravimetric analysis (TGA) and photoluminescent spectroscopy. Moreover, nitrogen adsorption−desorption measurement, electrochemical and photocatalysis properties for degradation of methylene blue (MB) upon a UV irradiation of compound 1 have been examined. - Graphical abstract: Two new compounds, [CuH{sub 3}L{sub 2}(GeMo{sub 12}O{sub 40})]·2H{sub 2}O (1) and [CuH{sub 3}L{sub 2}(SiMo{sub 12}O{sub 40})]·2H{sub 2}O (2) have been synthesized under hydrothermal conditions. The two compounds possess the left- and right-handed helical chains. - Highlights: • The tridentate L ligand is first used to synthesis Keggin-type polyoxometalates. • The two compounds possess the left- and right-handed Cu–L helical chains. • Relationship between surface properties and photocatalytic activity was studied. • Two compounds exhibit photoluminescence of ligand-to-metal charge transfer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Application of X-ray Technique to Study the Structure of Ultrafine-Grained Ferritic/Martensitic Steel

In this work, x-ray diffraction and transmission electron microscopy (TEM) analyses have been applied to study the structure of ultrafine-grained (UFG) ferritic/martensitic steel as compared to coarse-grained samples subjected to standard treatment. The x-ray phase analysis of diffraction patterns taken in the “transmission” mode allowed determining the volume fraction and phase composition of particles in the UFG samples. The lattice parameter, the size of coherent scattering domains, the averaged dislocation density, and the fraction of edge and screw dislocations of the ferritic phase in steel were determined according to the diffraction patterns taken in the “reflection” mode. The small-angle x-ray scattering (SAXS) technique was used to study the quantitative characteristics of the size, shape, and distribution of precipitates in the UFG samples. The TEM investigations were performed on the same foils to confirm the results of SAXS. The quantitative evaluations of dispersion and dislocation hardenings in ferritic/martensitic steel were conducted on the basis of the results obtained.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Medium range order and structural relaxation in As–Se network glasses through FSDP analysis

Synchrotron X-ray diffraction and neutron scattering studies are performed on As–Se glasses in two states: as-prepared (rejuvenated) and aged for ~27 years. The first sharp diffraction peak (FSDP) obtained from the structure factor data as a function of composition and temperature indicates that the cooperative processes that are responsible for structural relaxation do not affect FSDP. The results are correlated with the composition dependence of the complex heat capacity of the glasses and concentration of different structural fragments in the glass network. The comparison of structural information shows that density fluctuations, which were thought previously to have a significant contribution to FSDP, have much smaller effect than the cation–cation correlations, presence of ordered structural fragments or cage molecules.

glass transitions↗
DOE OSTI2017

Conformational landscape of a virus by single-particle X-ray scattering

Using a manifold-based analysis of experimental diffraction snapshots from an X-ray free electron laser, we determine the three-dimensional structure and conformational landscape of the PR772 virus to a detector-limited resolution of 9 nm. Our results indicate that a single conformational coordinate controls reorganization of the genome, growth of a tubular structure from a portal vertex and release of the genome. Furthermore, these results demonstrate that single-particle X-ray scattering has the potential to shed light on key biological processes.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2017

Alternative High-Performance Ceramic Waste Forms

This final report (M5NU-12-NY-AU # 0202-0410) summarizes the results of the project titled “Alternative High-Performance Ceramic Waste Forms,” funded in FY12 by the Nuclear Energy University Program (NEUP Project # 12-3809) being led by Alfred University in collaboration with Savannah River National Laboratory (SRNL). The overall focus of the project is to advance fundamental understanding of crystalline ceramic waste forms and to demonstrate their viability as alternative waste forms to borosilicate glasses. We processed single- and multiphase hollandite waste forms based on simulated waste streams compositions provided by SRNL based on the advanced fuel cycle initiative (AFCI) aqueous separation process developed in the Fuel Cycle Research and Development (FCR&D). For multiphase simulated waste forms, oxide and carbonate precursors were mixed together via ball milling with deionized water using zirconia media in a polyethylene jar for 2 h. The slurry was dried overnight and then separated from the media. The blended powders were then subjected to melting or spark plasma sintering (SPS) processes. Microstructural evolution and phase assemblages of these samples were studied using x-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersion analysis of x-rays (EDAX), wavelength dispersive spectrometry (WDS), transmission electron spectroscopy (TEM), selective area x-ray diffraction (SAXD), and electron backscatter diffraction (EBSD). These results showed that the processing methods have significant effect on the microstructure and thus the performance of these waste forms. The Ce substitution into zirconolite and pyrochlore materials was investigated using a combination of experimental (in situ XRD and x-ray absorption near edge structure (XANES)) and modeling techniques to study these single phases independently. In zirconolite materials, a transition from the 2M to the 4M polymorph was observed with increasing Ce content. The resulting powders were consolidated via SPS. Ce was reduced to the trivalent oxidation state and the zirconolite was converted into undesirable perovskite. The zirconolite polymorphs found in the synthesized powders were recovered after a post-SPS heat treatment in air. These results demonstrated the potential of processing in controlling the phase assemblage in these waste forms. Hollandites with Cr 3+ trivalent cations were identified as potential hosts for Cs immobilization and are being investigated for Cs retention properties. Series of compositions Ba 1.15-x Cs 2x Cr 2.3 Ti 5.7 O 16 , with increasing Cs loadings, were prepared by sol-gel process and characterized for structural parameters. Structural characterization was performed by a combination of powder XRD and neutron powder diffraction. Phase pure hollandite adapting monoclinic symmetry (I2/m) was observed for 0 ≤ x ≤ 0.55. These results were used to develop a new structural model to interpret Cs immobilization in these hollandites. Performance of these waste forms were evaluated for chemical durability and radiation resistance. Product consistency testing (PCT) and vapor hydration testing (VHT) were used for testing of chemical durability. Radiation resistance was tested using He + ions to simulate $\alpha$ particles and heavy ions such as Au 3+ to simulate a recoil. These results showed that these waste forms were chemically durable. The waste forms also amorphized to various degrees on exposure to simulated radiation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2019

Structural Modification of Starch Nanoparticles Via Graft Copolymerization Using KMnO{sub 4}, HClO{sub 4} and HNO{sub 3} Redox Pair

The novelty addressed here is commenced with a view to use our formerly prepared starch nanoparticles (SNPs) of size around 80–100 nm as a starting substrate for grafting meth acrylic acid (MAA) using KMnO{sub 4}, HClO{sub 4} in presence of HNO{sub 3} as innovative redox pair in aqueous medium. This was done to see the effect of SNPs with respect to well-dispersed nanosized particles, large surface areas, biodegradability and reactivity on the rate and extent of grafting. Besides; maximize the graft yield and graft reaction efficiency and reduce the homopolymer formation to lower extent. This could be accomplished via an in-depth assessment into the chief factors affecting the polymerization reaction such as initiator, monomer, SNPs and acid concentrations, time and temperature of polymerization, and liquor ratio. The results obtained indicate that the magnitude of the polymer yield including graft yield, graft reaction efficiency and homopolymer formation are determined by these factors. The structure of the resultant copolymers was confirmed instrumentally by Fourier transforms infrared spectroscopy; while both the surface morphology, crystalline structure and thermal properties were characterized by scanning electron microscopy, X-ray diffraction and thermal gravimetric analysis. Furthermore, the resultant copolymers were evaluated as environmental remediation materials via cadmium ions and cationic dyes removal from their solutions with different extent; in addition to higher swelling and chemical resistance in water as polar solvent and hydrochloric acid as acidic solution. The anticipated mechanisms involved in the synthesis are reported.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2016

Chromium doping effects on structural and dielectric properties of Mn-Zn cobaltites

The effect of transition metal Cr{sup 2+} ion as a dopant of Zn{sup 2+} in Mn{sub 0.5}Zn{sub 0.5}Co{sub 2}O{sub 4} is investigated. Co-doped Mn{sub 0.5}Zn{sub 0.5-x}Cr{sub x}Co{sub 2}O{sub 4} (x = 0, 0.3 and 0.5) cobaltites were prepared by solid-state reaction route. X-ray powder diffraction (XRD) analysis reveals that the samples prepared are polycrystalline single-phase cubic spinel in structure having a space group Fd3m. An increase in average particle size observed with Cr{sup 2+} doping. However other structural parameters such as X-ray density, micro strain and dislocation density shows almost a similar decreasing trend with increase in Cr{sup 2+}. High value of permittivity ∼10{sup 5} is observed for the parent Mn{sub 0.5}Zn{sub 0.5}Co{sub 2}O{sub 4} and shows a substantial decrease with increase in the Cr{sup 2+} doping. Higher doping of Cr{sup 2+} also increases the dielectric loss and hence limits its technological importance. At lower frequencies ac conductivity has been found to increase with increase in Cr{sup 2+} content.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗