Search NASA⌕ Search

SEARCH · Search NASA

Results for “Experimental methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

Experimental investigation of the excess charge and time constant of minority carriers in the thin diffused layer of 0.1 ohm-cm silicon solar cells

An experimental method is presented that can be used to interpret the relative roles of bandgap narrowing and recombination processes in the diffused layer. This method involves measuring the device time constant by open-circuit voltage decay and the base region diffusion length by X-ray excitation. A unique illuminated diode method is used to obtain the diode saturation current. These data are interpreted using a simple model to determine individually the minority carrier lifetime and the excess charge. These parameters are then used to infer the relative importance of bandgap narrowing and recombination processes in the diffused layer.

Godlewski, M. P.↗

Hydrogen chemistry - Perspective on experiment and theory

A review is presented of the advantages and limitations of various experimental methods for the investigation of the kinetics of hydrogen chemistry, including classic thermal and photochemical methods and the crossed molecular beam method. Special attention is given to the flash photolysis-resonance fluorescence apparatus developed by Braun et al, in which repetitive vacuum UV flashes result in the photolytic generation of the desired species, and to the discharge-flow technique. The use of various theoretical methods for the selection or elimination of kinetic data is considered in a brief discussion of the rate theory of two-body encounters and recombination-dissociation processes in neutral reactions. Recent kinetic studies of a series of OH reactions and of a major loss process for odd H in the stratosphere are summarized.

Kaufman, F.↗

A device for rapid determination of thermophysical properties of phase-change wind-tunnel models

An experimental method for direct measurement of the thermophysical properties of wind tunnel heat transfer models was developed. The technique consists of placing the model under a bank of high intensity, radiant heaters so that the fast opening water cooled shutters, which isolate the heater bank from the model, allow a step-input heat rate to be applied. Measurements of the heat transfer rate coupled with a surface-temperature time history of the same material are sufficient to determine the material thermophysical properties. An infrared thermometer is used to measure model surface temperature and a slug calorimeter provides heat transfer rate information. The output from the infrared thermometer and calorimeter is then fed into an analog-to-digital converter which provides digitized data to a computer. This computer then calculates combined thermophysical properties and a teleprinter prints out all the data. Thus, results are available within 7 minutes of test initiation as opposed to the weeks or months required using prior techniques.

Creel, T. R., Jr.↗

General aviation crash safety program at Langley Research Center

The purpose of the crash safety program is to support development of the technology to define and demonstrate new structural concepts for improved crash safety and occupant survivability in general aviation aircraft. The program involves three basic areas of research: full-scale crash simulation testing, nonlinear structural analyses necessary to predict failure modes and collapse mechanisms of the vehicle, and evaluation of energy absorption concepts for specific component design. Both analytical and experimental methods are being used to develop expertise in these areas. Analyses include both simplified procedures for estimating energy absorption capabilities and more complex computer programs for analysis of general airframe response. Full-scale tests of typical structures as well as tests on structural components are being used to verify the analyses and to demonstrate improved design concepts.

Thomson, R. G.↗

Meteorological radar facility (MRF) slot conductance investigations

A preliminary meteorological radar facility (MRF) array design was completed in support of the slot conductance measurement program. Three different slot measurement techniques were evaluated. The selection of the probe comparison measurement technique was selected as the principal experimental method with the impedance measurement technique chosen to measure a few higher conductance slots to be used as reference slots. The impedance of 43 slots in 0.9 x 0.4 inch standard waveguide and of 40 slots in 0.835 x 0.4 inch waveguide was measured. Also, impedance measurements were made of a few slots using image planes to simulate mutual coupling effects. The measured and theoretical conductance, susceptance, and radiation phase data are presented in graphic form as a function of slot displacement for constant slot length, and of slot length for constant slot displacement. It is concluded that the proposed MRF array design approach is a feasible one.

Ratkevich, A. E.↗

Gray-level transformations for interactive image enhancement.

A gray-level transformation method suitable for interactive image enhancement is presented. It is shown that the well-known histogram equalization technique is a special case of this method. Experimental results which establish the superiority of the procedure over histogram equalization are also described.

Gonzalez, R. C.↗

A preliminary in-duct measurement of spinning modes in the inlet of a rotating vehicle

Suppression of noise radiated from a jet engine duct is an important environmental problem. Results are presented for a study aimed at developing and evaluating an experimental method for measuring the complex acoustic pressure field at a plane in the inlet of a fan duct. The theory of modal propagation is outlined and related to the theory of measuring spinning modes in the duct. A spinning mode measurement apparatus is described, and preliminary test results of the modal measurement for several operating speeds are presented. The measurement of spinning modes is successfully carried out in the inlet of a rotating vehicle under conditions representative of an actual jet engine. Data repeatability and problems encountered in the measurement are examined. In particular, it is important to calibrate the probe systems for phase and level. Recommendations for future improvements in the method are made.

Kraft, R. E.↗

Sodium ions at defect sites at SiO2/Si interfaces as determined by X-ray photoelectron spectroscopy

X-ray photoelectron spectroscopy (XPS) is described in its application as a probe for studying defects such as sodium in SiO2 films. A general description is given of key experimental methods in XPS. Techniques are described for applying and monitoring a fixed bias at the surface of the oxide during the XPS measurement. These methods are shown to be capable of detecting extremely small Na and Cu concentrations in undoped samples (less than 10 to the 11th power per cu cm). In deliberately Na-doped samples, five spectral peaks are distinctly observed and related to different defect states at the vacuum/SiO2 and SiO2/Si interfaces. By applying a bias-temperature stress during the XPS measurements, these peaks change in relative intensity and can be related to the motion of the Na(+) ions between different states occurring at the two interfaces. An attempt is made to correlate the observations with previously reported models.

Grunthaner, F. J.↗

Tunnel injection into gate oxide traps

An experimental method is described for measuring the density of oxide traps in the gate oxide of an MOS transistor as a function of energy and position near the silicon interface. Measurements are obtained from different oxide growth processes and after Co-60 irradiation. The results are related to long-term drift of threshold voltage.

Maserjian, J.↗

Wind tunnel test and calibration techniques for the measurement of damping and dynamic cross derivatives due to pitching and yawing

The paper shows how the oscillatory apparatus described previously by Orlik-Rueckemann et al. (1974) for determining cross and cross-coupling moment derivatives due to pitching and yawing oscillation is strengthened, extensively modified, and adapted to permit operation in a large continuous-flow wind tunnel. Particular attention is given to an electromagnetic three-degrees-of-freedom calibrating system developed to verify the validity of the experimental method and the various aspects of data reduction procedure. Typical results from calibration tests and from a series of wind tunnel experiments are presented. The only significant limitation is that the apparatus can only be used for models that are relatively small and have a conically-shaped longitudinal cavity.

Hanff, E. S.↗

Bubble dielectrophoresis

The theoretical principles related to bubble dielectrophoresis are examined, taking into account the polarization force, aspects of bubble deformation, the electrostatic bubble levitation theorem, and the equation of motion. The measurement of the dielectrophoretic force on static and dynamic bubbles represents a convenient experimental method for the study of the general problem of dielectrophoresis. The experiments reported include static-force measurements, static-levitation experiments, and dynamic-force measurements.

Jones, T. B.↗

Gray-level transformations for interactive image enhancement

A gray-level transformation method suitable for interactive image enhancement is presented. It is shown that the well-known histogram equalization technique is a special case of this method. Experimental results which illustrate the enhancement capabilities of the procedure are also described.

Gonzalez, R. C.↗

Effects of forward velocity on noise for a J85 turbojet engine with multitube suppressor from wind tunnel and flight tests

Flight tests and wind tunnel noise tests using a J85 engine with some representative jet exhaust noise suppressors are reported. Capabilities and limitations of the two types of experimental methods are evaluated with emphasis on investigation of forward velocity effects. The suppressor arrangement was a 104-elliptical-tube nozzle configuration, with or without an acoustically lined shroud. The suppressor noise levels are found not reduced as much by forward velocity as expected for unsuppressed jets. The directivity and forward velocity effects appear more similar to predicted trends for internally generated noise than for unsuppressed jet noise.

Stone, J. R.↗

Tetroon evaluation program

The actual volume of a constant volume superpressured tetrahedron shaped balloon changes as the amount of superpressure is changed. The experimental methods used to measure these changes in volume are described and results are presented. The basic equations used to determine the amount of inflation gas required for a tetroon to float at a predetermined flight level are presented and inflation techniques discussed.

Beemer, J. D.↗

Transcutaneous measurement of volume blood flow

Blood flow velocity measurements, using Doppler velocimeter, are described. The ability to measure blood velocity using ultrasound is derived from the Doppler effect; the change in frequency which occurs when sound is reflected or transmitted from a moving target. When ultrasound of the appropriate frequency is transmitted through a moving blood stream, the blood cells act as point scatterers of ultrasonic energy. If this scattered ultrasonic energy is detected, it is found to be shifted in frequency according to the velocity of the blood cells, nu, the frequency of the incident sound, f sub o, the speed of sound in the medium, c, and the angle between the sound beam and the velocity vector, o. The relation describing this effect is known as the Doppler equation. Delta f = 2 f sub o x nu x cos alpha/c. The theoretical and experimental methods are evaluated.

Daigle, R. E.↗

Determination of the zincate diffusion coefficient and its application to alkaline battery problems

The diffusion coefficient for the zincate ion at 24 C was found to be 9.9 X 10 to the minus 7th power squared cm per sec + or - 30 percent in 45 percent potassium hydroxide and 1.4 x 10 to the minus 7 squared cm per sec + or - 25 percent in 40 percent sodium hydroxide. Comparison of these values with literature values at different potassium hydroxide concentrations show that the Stokes-Einstein equation is obeyed. The diffusion coefficient is characteristic of the zincate ion (not the cation) and independent of its concentration. Calculations with the measured value of the diffusion coefficient show that the zinc concentration in an alkaline zincate half cell becomes uniform throughout in tens of hours by diffusion alone. Diffusion equations are derived which are applicable to finite size chambers. Details and discussion of the experimental method are also given.

May, C. E.↗

The effect of load in a contact with boundary lubrication

The effect of the transition load on the wear in a contact with boundary lubrication was investigated. An experimental method was developed for this purpose, and parameters affecting the boundary lubrication under industrial operating conditions were identified. These parameters are the adsorbed boundary film, the contact microgeometry (surface roughness), macrogeometry, and hardness of materials used. It was found that the curve of the tops of the surface protrustion affect the transition load, and thus the boundary lubrication. The transition load also depends on the chemical nature of the contact and its geometrical and mechanical aspects.

Georges, J. M.↗

Residual stresses in angleplied laminates and their effects on laminate behavior

NASA Lewis Research Center research in the field of composite laminate residual stresses is reviewed and summarized. The origin of lamination residual stresses, evidence of their presence, experimental methods for measuring them, and theoretical methods for predicting them are described. Typical results are presented which show the magnitudes of residual stresses in various laminates including hybrids and superhybrids, and in other complex composite components. Results are also presented which show the effects of lamination residual stresses on laminate warpage and on laminate mechanical properties including fracture stresses. Finally, the major findings and conclusions derived therefrom are summarized.

Chamis, C. C.↗