Search NASA⌕ Search

SEARCH · Search NASA

Results for “Positive Transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56

In-flight calibration of the fine pointing Sun sensor on the solar maximum mission

The attitude control objectives of solar maximum mission are to point the boresight of the payload fine pointing sun sensor (FPSS) to any point within 30 arc-minutes of the Sun's center with an accuracy of 5 arc-seconds (3 sigma, pitch and yaw) and a jitter of less than 3 arc-seconds (3 sigma). To meet these stringent accuracy requirements, a procedure was developed for in-flight calibration of the FPSS. The spacecraft was maneuvered using FPSS offset commands to position the Sun at different points within the FPSS field of view. The coefficients of the FPSS digital to analog nonlinear transfer function were determined by minimizing the residuals between the pitch and yaw angles computed from the FPSS measurements and the corresponding reference angles obtained from inertial reference unit measurements. The actual in-flight calibration and the calibration algorithm are discussed.

Gambardella, P. J.↗

Global positioning system timing receivers in the DSN

The system (GPS) is a worldwide navigation system using a constellation of Earth satellites with onboard clocks. The GPS is also usable to transfer time and frequency. Preliminary tests with the breadboard receiver at NBS produced precision in time and frequency transfer between the United States Naval Observatory (USNO) and NBS. JPL's plans to install receivers in the DSN to demonstrate their ability to transfer time and frequency within the DSN and between the DSN and outside agencies are discussed.

Clements, P. A.↗

Low concentration ratio solar array structural configuration

The design and structural properties of a low concentration ratio solar array are discussed. The assembled module consists of six interconnected containers which are compactly stowed in a volume of 3.24 m(3) for delivery to orbit by the shuttle. The containers deploy in accordian fashion into a rectangular area of 19.4 x 68 meters and can be attached to the user spacecraft along the longitudinal centerline of the end container housing. Five rotary incremental actuators requiring about 8 watts each will execute the 180-degree rotation at each joint. Deployable masts (three per side) are used to extend endcaps from the housing in both directions. Each direction is extended by three masts requiring about 780 watts for about 27 minutes. Concentrator elements are extended by the endcaps and are supported by cable systems that are connected between the housings and endcaps. These power generating elements contain reflector panels which concentrate light onto the solar panels consisting of an aluminum radiator with solar cells positioned within the element base formed by the reflectors. A flat wire harness collects the power output of individual elements for transfer to the module container housing harnesses.

Nalbandian, S. J.↗

Mass transfer in cataclysmic variables - Clues from the dwarf nova period distribution

Evidence is presented in support of the hypothesis that the mean mass-transfer rate at a given orbital period is not continuous across the 2-3 hr gap in the orbital period distribution for cataclysmic variables. It is pointed out that although dwarf novae comprise nearly half (48 percent) of all disk systems with orbital periods less than 10 hr, only three systems out of the 22 with periods between 3 and 4 hr appear to be dwarf novae. The overall orbital period distribution for dwarf novae in conjunction with the predictions from current theories of dwarf nova eruptions are used to argue that mass-transfer rates must be generally higher for systems with orbital periods greater than 3 hr relative to systems with periods less than 2 hr. It is further argued that the mean mass-transfer rate at a given orbital period cannot increase more steeply than P exp 1.7 unless the white dwarf mass is positively correlated with orbital period.

Shafter, A. W.↗

Robustness analysis based on passivity

A technique of robust stability analysis for multivariable control systems is introduced. Existing tools in the literature are mostly based on small gain type of conditions such as the H(infinity)-norm or mu measure. In contrast, the approach presented is motivated by passivity theory. The natural energy Lyapunov function associated with a passive system allows robustness to be analyzed with Lyapunov stability theory. Consequently, nonlinear and time-varying perturbations can be considered within the same framework. For unstructured uncertainties, the robustness margin is characterized in terms of an index related to the Hermitian part of a transfer function. If the uncertainties contain additional diagonal structure, stability margins are obtained for variations of each uncertain block in both positive and negative directions. Applications of this robustness analysis technique are illustrated.

Wen, John T.↗

Segmented Arm For Positioning And Assembly

Proposed segmented robotic arm for positioning and assembly of components of large structures contains motor-and-flywheel angular-momentum devices in each arm segment. Transfers angular momentum to and from segments of arm to produce desired motion of arm. Conceived for use in outer space, concept adaptable to terrestrial uses in which buoyancy cancels effect of gravitation - (floating on or under water).

Berka, Reginald B.↗

Experimental studies of shock-wave/wall-jet interaction in hypersonic flow, part A

Experimental studies have been conducted to examine slot film cooling effectiveness and the interaction between the cooling film and an incident planar shock wave in turbulent hypersonic flow. The experimental studies were conducted in the 48-inch shock tunnel at Calspan at a freestream Mach number of close to 6.4 and at a Reynolds number of 35 x 10(exp 6) based on the length of the model at the injection point. The Mach 2.3 planar wall jet was generated from 40 transverse nozzles (with heights of both 0.080 inch and 0.120 inch), producing a film that extended the full width of the model. The nozzles were operated at pressures and velocities close to matching the freestream, as well as at conditions where the nozzle flows were over- and under-expanded. A two-dimensional shock generator was used to generate oblique shocks that deflected the flow through total turnings of 11, 16, and 21 degrees; the flows impinged downstream of the nozzle exits. Detailed measurements of heat transfer and pressure were made both ahead and downstream of the injection station, with the greatest concentration of measurements in the regions of shock-wave/boundary layer interaction. The major objectives of these experimental studies were to explore the effectiveness of film cooling in the presence of regions of shock-wave/boundary layer interaction and, more specifically, to determine how boundary layer separation and the large recompression heating rates were modified by film cooling. Detailed distributions of heat transfer and pressure were obtained in the incident-shock/wall-jet interaction region for a series of shock strengths and impingement positions for each of the two nozzle heights. Measurements were also made to examine the effects of nozzle lip thickness on cooling effectiveness. The major conclusion from these studies was that the effect of the cooling film could be readily dispersed by relatively weak incident shocks, so the peak heating in the recompression region was not significantly reduced by even the largest levels of film cooling. For the case studies in the absence of film cooling, the interaction regions were unseparated. However, adding film cooling resulted in regions of boundary layer separation induced in the film cooling layer, the size of which regions first increased and then decreased with increased film cooling. Surprisingly, the size of the separated regions and the magnitude of the recompression heating were not strongly influenced by the thickness of the cooling film, nor by the point of shock impingement relative to the exit plane of the nozzles. The lip thickness was found to have little effect on cooling effectiveness. Measurements with and in the absence of shock interaction were compared with the results of earlier experimental studies and correlated in terms of the major parameters controlling these flows.

Holden, Michael S.↗

Molecular Dynamics Simulation of a Multi-Walled Carbon Nanotube Based Gear

We used molecular dynamics to investigate the properties of a multi-walled carbon nanotube based gear. Previous work computationally suggested that molecular gears fashioned from (14,0) single-walled carbon nanotubes operate well at 50-100 gigahertz. The gears were formed from nanotubes with teeth added via a benzyne reaction known to occur with C60. A modified, parallelized version of Brenner's potential was used to model interatomic forces within each molecule. A Leonard-Jones 6-12 potential was used for forces between molecules. The gear in this study was based on the smallest multi-walled nanotube supported by some experimental evidence. Each gear was a (52,0) nanotube surrounding a (37,10) nanotube with approximate 20.4 and 16,8 A radii respectively. These sizes were chosen to be consistent with inter-tube spacing observed by and were slightly larger than graphite inter-layer spacings. The benzyne teeth were attached via 2+4 cycloaddition to exterior of the (52,0) tube. 2+4 bonds were used rather than the 2+2 bonds observed by Hoke since 2+4 bonds are preferred by naphthalene and quantum calculations by Jaffe suggest that 2+4 bonds are preferred on carbon nanotubes of sufficient diameter. One gear was 'powered' by forcing the atoms near the end of the outside buckytube to rotate to simulate a motor. A second gear was allowed to rotate by keeping the atoms near the end of its outside buckytube on a cylinder. The ends of both gears were constrained to stay in an approximately constant position relative to each other, simulating a casing, to insure that the gear teeth meshed. The stiff meshing aromatic gear teeth transferred angular momentum from the powered gear to the driven gear. The simulation was performed in a vacuum and with a software thermostat. Preliminary results suggest that the powered gear had trouble turning the driven gear without slip. The larger radius and greater mass of these gears relative to the (14,0) gears previously studied requires a smaller rotation rate and multiple rows of teeth to avoid excessive force on the gear teeth resulting, in slip and failure of the driven gear to turn. We hope that studies such as these will eventually lead to synthesis of components that can be assembled into atomically precise fullerene machines. These machines, in turn, may someday be used in machine-phase fullerene materials with remarkable properties.

Han, Jie↗

Directional spectral emissivity measurement system

Apparatus and process for determining the emissivity of a test specimen including an integrated sphere having two concentric walls with a coolant circulating therebetween, and disposed within a chamber which may be under ambient, vacuum or inert gas conditions. A reference sample is disposed within the sphere with a monochromatic light source in optical alignment therewith. A pyrometer is in optical alignment with the test sample for obtaining continuous test sample temperature measurements during a test. An arcuate slit port is provided through the spaced concentric walls of the integrating sphere with a movable monochromatic light source extending through and movable along the arcuate slit port. A detector system extends through the integrating sphere for continuously detecting an integrated signal indicative of all radiation within its field of view, as a function of the emissivity of the test specimen at various temperatures and various angle position of the monochromatic light source. A furnace for heating the test sample to approximately 3000 K. and control mechanism for transferring the heated sample from the furnace to the test sample port in the integrating sphere is also contained within the chamber.

Halyo, Nesim↗

Covering a Crucible with Metal Containing Channels

In a procedure that partly resembles the lost-wax casting process, a crucible made of a brittle material (ceramic, quartz, or glass) is covered with a layer of metal containing channels. The metal cover and the channels can serve any or all of several purposes, depending upon the application: Typically, the metal would serve at least partly to reinforce the crucible. The channels could be used as passages for narrow objects that could include thermocouples and heat-transfer strips. Alternatively or in addition, channels could be used as flow paths for liquid or gaseous coolants and could be positioned and oriented for position- or direction-selective cooling. In some cases, the channels could be filled with known gases and sealed so that failure of the crucibles could be indicated by instruments that detect the gases. The process consists of three main steps. In the first step, a pattern defining the channels is formed by wrapping or depositing a material in the desired channel pattern on the outer surface of the crucible. The pattern material can be a plastic, wax, low-ash fibrous material, a soluble material, or other suitable material that can subsequently be removed easily. In a proof-of-concept demonstration (see figure), the crucible was an alumina cylinder and the mold material was plastic tie-down tape. In the second step, the patterned crucible is coated with metal. In one variation of the second step, a very thin layer containing or consisting of an electrically conductive material (e.g., gold, silver, or carbon) is painted or otherwise deposited on the mold-covered crucible, then the covering metal required for the specific application is electrodeposited on the very thin conducting layer. In another variation of the second step, the metal coat is formed by chemical vapor deposition. In the proof-of-concept demonstration, a layer of nickel 0.003 in. ( 0.08 mm) thick was electrodeposited. In the third step, the patterned material is removed. This is generally done by heating the crucible assembly until the patterned material melts and runs out, vaporizes, and/or decomposes to an ash, leaving the channels. Alternatively, if the patterned material is soluble, it can be removed by use of a suitable solvent. In the proof-of-concept demonstration, the tape was burned away by heating the assembly to a temperature of 600 C.

Grugel, Richard N.↗

The Influence of Ozone Precursor Emissions from Four World Regions on Tropospheric Composition and Radiative Climate Forcing

Ozone (O3) precursor emissions influence regional and global climate and air quality through changes in tropospheric O3 and oxidants, which also influence methane (CH4) and sulfate aerosols (SO4 (sup 2-)). We examine changes in the tropospheric composition of O3, CH4, SO4 (sup 2-) and global net radiative forcing (RF) for 20% reductions in global CH4 burden and in anthropogenic O3 precursor emissions (NOx, NMVOC, and CO) from four regions (East Asia, Europe and Northern Africa, North America, and South Asia) using the Task Force on Hemispheric Transport of Air Pollution Source-Receptor global chemical transport model (CTM) simulations, assessing uncertainty (mean plus or minus 1 standard deviation) across multiple CTMs. We evaluate steady state O3 responses, including long-term feedbacks via CH4. With a radiative transfer model that includes greenhouse gases and the aerosol direct effect, we find that regional NOx reductions produce global, annually averaged positive net RFs (0.2 plus or minus 0.6 to 1.7 2 mWm(sup -2)/Tg N yr(sup -1), with some variation among models. Negative net RFs result from reductions in global CH4 (-162.6 plus or minus 2 mWm(sup -2) for a change from 1760 to 1408 ppbv CH4) and regional NMVOC (-0.4 plus or minus 0.2 to 0.7 plus or minus 0.2 mWm(sup -2)/Tg C yr(sup -1) and CO emissions (-0.13 plus or minus 0.02 to -0.15 plus or minus 0.02 mWm(sup-2)/Tg CO yr(sup-1). Including the effect of O3 on CO2 uptake by vegetation likely makes these net RFs more negative by -1.9 to- 5.2 mWm(sup -2)/Tg N yr(sup -1), -0.2 to -0.7 mWm(sup -2)/Tg C yr(sup -1), and -0.02 to -0.05 mWm(sup -2)/ Tg CO yr(sup -1). Net RF impacts reflect the distribution of concentration changes, where RF is affected locally by changes in SO4 (sup -2), regionally to hemispherically by O3, and globally by CH4. Global annual average SO4 2 responses to oxidant changes range from 0.4 plus or minus 2.6 to -1.9 plus or minus 1.3 Gg for NOx reductions, 0.1 plus or minus 1.2 to -0.9 plus or minus 0.8 Gg for NMVOC reductions, and -0.09 plus or minus 0.5 to -0.9 plus or minus 0.8 Gg for CO reductions, suggesting additional research is needed. The 100-year global warming potentials (GWP(sub 100)) are calculated for the global CH4 reduction (20.9 plus or minus 3.7 without stratospheric O3 or water vapor, 24.2 plus or minus 4.2 including those components), and for the regional NOx, NMVOC, and CO reductions (18.7 plus or minus 25.9 to 1.9 plus or minus 8.7 for NOx, 4.8 plus or minus 1.7 to 8.3 plus or minus 1.9 for NMVOC, and 1.5 plus or minus 0.4 to 1.7 plus or minus 0.5 for CO). Variation in GWP(sub 100) for NOx, NMVOC, and CO suggests that regionally specific GWPs may be necessary and could support the inclusion of O3 precursors in future policies that address air quality and climate change simultaneously. Both global net RF and GWP100 are more sensitive to NOx and NMVOC reductions from South Asia than the other three regions.

ozone↗

An Evaluation of the Liquid Cloud Droplet Effective Radius Derived from MODIS, Airborne Remote Sensing, and in Situ Measurements from CAMP2Ex

The cloud drop effective radius (Re) of the drop size distribution derived from passive satellite sensors is a key variable used in climate research. Validation of these satellite products has often taken place under stratiform cloud conditions that favor the assumption of cloud horizontal homogeneity used by the retrieval techniques. However, many studies have noted concerns with respect to significant biases in retrieved Re arising from cloud heterogeneity, for example, in cumulus cloud fields. Here, we examine data collected during the 2019 “Cloud, Aerosol and Monsoon Processes Philippines Experiment” (CAMP2Ex), which, in part, targeted the objective of providing the first detailed evaluation of Re retrieved across multiple platforms and techniques in a cumulus and congestus cloud region. Our evaluation consists of cross-comparisons of Re between the Moderate Resolution Imaging Spectroradiometer (MODIS) onboard the Terra satellite, the Research Scanning Polarimeter (RSP) onboard the NASA P-3 aircraft, and in situ measurements from both the NASA P-3 and Learjet aircraft that are all taken in close spatiotemporal proximity to the same cloud fields. A particular advantage of our approach lies in the capability of the RSP to retrieve Re using a bi-spectral MODIS approach and a polarimetric approach, which allows for the evaluation of bi-spectral and polarimetric Re retrievals from an airborne perspective using the same samples. Averaged over all P-3 flight segments examined here for warm clouds, the RSP polarimetric method, the in situ method, and the bias-adjusted MODIS method of Fu et al. (2019) show a comparable median (mean ± standard deviation) for the Re samples of 9.6 (10.2 ± 4.0) µm, 11.0 (13.6 ± 11.3) µm, and 10.4 (10.8 ± 3.8) µm, respectively. These values are far lower than the values of 15.1 (16.2 ± 5.5) µm and 17.2 (17.7 ± 5.7) µm from the bi-spectral retrievals of RSP and MODIS, respectively. Similar results are observed when Re is segregated by cloud-top height and in detailed case studies. The clouds sampled during CAMP2Ex consist of mostly small (mean transect length ∼ 1.4 km) and low clouds (mean cloud-top height ∼ 1 km), which had more numerous small clouds than the trade wind cumuli sampled in past field campaigns such as Rain in Shallow Cumulus over the Ocean (RICO) and the Indian Ocean Experiment (INDOEX). The overestimates of Re from the RSP bi-spectral technique compared with the polarimetric technique increased as cloud size and cloud optical depth decreased. Drizzle, cloud-top bumpiness, and solar zenith angle, however, are not closely correlated with the overestimate of bi-spectral Re. For shallow clouds that dominated the liquid cloud cover for the CAMP2Ex region and period, we show that 3-D radiative transfer and cloud heterogeneity, particularly for the optically thin and small clouds, appear to be the leading cause of the large positive biases in bi-spectral retrievals. Because this bias varies with the underlying structure of the cloud field, caution continues to be warranted in studies that use bi-spectral Re retrievals in cumulus cloud fields.

Cloud microphysics↗

Insights and Observations From Operating A Laser Communication Terminal on the International Space Station (ISS)

The Integrated Laser Communication Relay Demonstration (LCRD) Low Earth Orbit User Modem and Amplifier Terminal (ILLUMA-T) is the first user platform for NASA’s first laser communication relay, LCRD. ILLUMA-T is hosted on the International Space Station (ISS) as an external payload of the Japanese Experiment Module – Exposed Facility (JEM-EF) situated in slot 3. The LCRD payload is hosted on the STPSat-6 spacecraft, which orbits Earth in a geostationary orbit at position 112 W. The ILLUMA-T-to-LCRD system provides a bidirectional, space-to-ground laser communication relay link transferring data up to 1.2 Gbps utilizing two optical ground stations (OGS), OGS-1 in California and OGS-2 in Hawai’i. This paper describes lessons learned from operating the ILLUMA-T system and examines topics such as the end-to-end system availability, predictive versus actual ephemeris, acquisition adjustments, modem timing and handshaking, the terminal’s physical placement and accommodations, and experiment development, execution, and analysis. The authors of this paper operate both the LCRD and ILLUMA-T laser terminals on a daily basis including pass planning, procedure execution, acquisition analysis, and real-time terminal commanding and telemetry monitoring. LCRD is a joint project involving NASA Goddard Space Flight Center (GSFC), the California Institute of Technology Jet Propulsion Laboratory (JPL), and Massachusetts Institute of Technology Lincoln Laboratory (MIT LL). The ILLUMA-T payload is managed by NASA GSFC in Greenbelt, Maryland whose partners include the ISS program office at NASA’s Johnson Space Center (JSC) in Houston, Texas; the Huntsville Operations Support Center (HOSC) at Marshall Space Flight Center (MSFC) in Huntsville, Alabama; the Glenn Research Center (GRC) in Cleveland, Ohio; and the MIT LL in Lexington, Massachusetts. ILLUMA-T is funded by the Space Communications and Navigation (SCaN) Program at NASA Headquarters in Washington, D.C.

Laser Communications↗

Impaction densitometer

Disclosed is an impaction densitometer having a chamber configured to receive a particle; a beam generator configured to emit a beam; a detector configured to receive the beam and convert a change in intensity of the received beam into an electrical signal corresponding to a particle volume; an impact sensor positioned a known distance from the beam and configured to measure a particle momentum as a function of an impact energy transferred from the particle to the impact sensor; a velocity calculator configured to calculate a particle velocity based on a time it takes the particle to pass through the beam and strike the impact sensor; a mass calculator configured to calculate a particle mass as a function of the particle momentum and velocity; and a density calculator configured to calculate a particle density as a function of the particle mass and volume.

43 PARTICLE ACCELERATORS↗

Intra-molecular Charge Transfer and Electron Delocalization in Non-fullerene Organic Solar Cells

Two types of electron acceptors were synthesized by coupling two kinds of electron-rich cores with four equivalent perylene diimides (PDIs) at the a position. With fully aromatic cores, TPB and TPSe have pi-orbitals spread continuously over the whole aromatic conjugated backbone, unlike TPC and TPSi, which contain isolated PDI units due to the use of a tetrahedron carbon or silicon linker. Density functional theory calculations of the projected density of states showed that the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) for TPB are localized in separate regions of space. Further, the LUMO of TPB shows a greater contribution from the orbitals belonging to the connective core of the molecules than that of TPC. Overall, the properties of the HOMO and LUMO point at increased intra-molecular delocalization of negative charge carriers for TPB and TPSe than for TPC and TPSi and hence at a more facile intra-molecular charge transfer for the former. The film absorption and emission spectra showed evidences for the inter -molecular electron delocalization in TPB and TPSe, which is consistent with the network structure revealed by X-ray diffraction studies on single crystals of TPB. These features benefit the formation of charge transfer states and/or facilitate charge transport. Thus, higher electron mobility and higher charge dissociation probabilities under J sc condition were observed in blend films of TPB:PTB7-Th and TPSe:PTB7-Th than those in TPC:PTB7Th and TPSi:PTB7-Th blend films. As a result, the J sc and fill factor values of 15.02 mA/cm 2 , 0.58 and 14.36 mA/cm 2 , 0.55 for TPB- and TPSe-based solar cell are observed, whereas those for TPC and TPSi are 11.55 mA/cm 2 , 0.47 and 10.35 mA/cm 2 , 0.42, respectively.

14 SOLAR ENERGY↗

Data and Time Transfer Using SONET Radio

The need for precise knowledge of time and frequency has become ubiquitous throughout our society. The areas of astronomy, navigation, and high speed wide-area networks are among a few of the many consumers of this type of information. The Global Positioning System (GPS) has the potential to be the most comprehensive source of precise timing information developed to date; however, the introduction of selective availability has made it difficult for many users to recover this information from the GPS system with the precision required for today's systems. The system described in this paper is a 'Synchronous Optical NetWORK (SONET) Radio Data and Time Transfer System'. The objective of this system is to provide precise time and frequency information to a variety of end-users using a two-way data and time-transfer system. Although time and frequency transfers have been done for many years, this system is unique in that time and frequency information are embedded into existing communications traffic. This eliminates the need to make the transfer of time and frequency informatio a dedicated function of the communications system. For this system SONET has been selected as the transport format from which precise time is derived. SONET has been selected because of its high data rates and its increasing acceptance throughout the industry. This paper details a proof-of-concept initiative to perform embedded time and frequency transfers using SONET Radio.

Graceffo, Gary M.↗

Parallel Loss of Plastid Introns and Their Maturase in the Genus Cuscuta

Plastid genome content and arrangement are highly conserved across most land plants and their closest relatives, streptophyte algae, with nearly all plastid introns having invaded the genome in their common ancestor at least 450 million years ago. One such intron, within the transfer RNA trnK-UUU, contains a large open reading frame that encodes a presumed intron maturase, matK. This gene is missing from the plastid genomes of two species in the parasitic plant genus Cuscuta but is found in all other published land plant and streptophyte algal plastid genomes, including that of the nonphotosynthetic angiosperm Epifagus virginiana and two other species of Cuscuta. By examining matK and plastid intron distribution in Cuscuta, we add support to the hypothesis that its normal role is in splicing seven of the eight group IIA introns in the genome. We also analyze matK nucleotide sequences from Cuscuta species and relatives that retain matK to test whether changes in selective pressure in the maturase are associated with intron deletion. Stepwise loss of most group IIA introns from the plastid genome results in substantial change in selective pressure within the hypothetical RNA-binding domain of matK in both Cuscuta and Epifagus, either through evolution from a generalist to a specialist intron splicer or due to loss of a particular intron responsible for most of the constraint on the binding region. The possibility of intron-specific specialization in the X-domain is implicated by evidence of positive selection on the lineage leading to C. nitida in association with the loss of six of seven introns putatively spliced by matK. Moreover, transfer RNA gene deletion facilitated by parasitism combined with an unusually high rate of intron loss from remaining functional plastid genes created a unique circumstance on the lineage leading to Cuscuta subgenus Grammica that allowed elimination of matK in the most speciesrich lineage of Cuscuta.

59 BASIC BIOLOGICAL SCIENCES↗