Search NASA⌕ Search

SEARCH · Search NASA

Results for “cell parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Development and pilot line production of lithium doped silicon solar cells

The work performed over the period of September 1971 to August 1972 to develop production processes for fabrication of lithium doped P/N cells is described. The BCl3 diffusion without 02 was selected as the optimum diffusion process for fabrication of lithium doped cells. An 8-2-7 (warm up - deposition - drive-in time in minutes) diffusion schedule at 1055 C was used for the first two lots (300 cells each) delivered to JPL. Cell efficiencies ranged from 11.0 to 13.7% based on an AMO of 135.3 mW/sq cm. These high efficiencies were obtained using from 10 to 40 cells per boron diffusion; increasing the quantity beyond 40 resulted in lower outputs. At this point, the emphasis was placed on investigation of a BCl3 with 02 diffusion. Through evaluation of the effects of diffusion time and temperature, gas flow rates, and desposition plus drive-in vs. continuous deposition and no drive-in cycles, diffusion parameters were determined which produced short circuit currents of 136 + or - 4 mA for ten cells spaced along 12 in. of the diffusion boat. The quantity was increased to 60, 100, and 150 cell diffusions with no more variation in cell short circuit current than observed with 10 cells.

Payne, P. A.↗
DOE OSTI2022

Simultaneous imaging and diffraction in the dynamic diamond anvil cell

The ability to visualize a sample undergoing a pressure-induced phase transition allows for the determination of kinetic parameters, such as the nucleation and growth rates of the high-pressure phase. For samples that are opaque to visible light (such as metallic systems), it is necessary to rely on x-ray imaging methods for sample visualization. Here, we present an experimental platform developed at beamline P02.2 at the PETRA III synchrotron radiation source, which is capable of performing simultaneous x-ray imaging and diffraction of samples that are dynamically compressed in piezo-driven diamond anvil cells. This setup utilizes a partially coherent monochromatic x-ray beam to perform lensless phase contrast imaging, which can be carried out using either a parallel- or focused-beam configuration. The capabilities of this platform are illustrated by experiments on dynamically compressed Ga and Ar. Melting and solidification were identified based on the observation of solid/liquid phase boundaries in the x-ray images and corresponding changes in the x-ray diffraction patterns collected during the transition, with significant edge enhancement observed in the x-ray images collected using the focused-beam. These results highlight the suitability of this technique for a variety of purposes, including melt curve determination.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Constitutive model development of aluminum alloy 1100 for elevated temperature forming process

Commercially pure aluminum alloy, AA1100, presents good electrical and thermal conductivity, high formability, and low cost. Those favorable characteristics have the potential to enable bipolar plates with improved economics and enhanced performance compared to current stainless steel bipolar plates for proton exchange membrane fuel cells. An accurate constitutive model is essential to develop and optimize processing parameters and effectively control the forming process. Here, the objective of this work is to develop a constitutive model of AA1100 that is able to simulate stress-strain relation, formed geometry, and predict the onset of fracture strain to avoid forming failure. Initially, a set of tensile tests at temperature between 300 and 500°C and strain rate between 0.005 and 1.0/s were conducted to examine the deformation behavior. Then, a set of damage-based unified visco-plastic constitutive equations is proposed and calibrated based on the results of stress-strain data. A genetic algorithm optimization method is applied to search for best fitting material constants in constitutive equations. The proposed model shows good predictability of both the stress-strain relation and fracture strain at low strain rate and high temperature conditions. The accuracy of proposed model is also evaluated statistically. A comparison of the proposed model with three popular models (Arrhenius-type mode, Johnson-Cook model and Zerilli-Armstrong model) was made. The proposed model shows the best experimental agreement with correlation coefficient of 0.96 in contrast to 0.25, 0.38 and 0.75 for the popular models, respectively. The proposed model can help to optimize the elevated temperature forming process and guide die design to enable optimal geometric features in the formed components.

08 HYDROGEN↗
DOE OSTI2025

Scalable phononic metamaterials: Tunable bandgap design and multi-scale experimental validation

Phononic metamaterials offer unprecedented control over wave propagation, making them essential for applications such as vibration isolation, waveguiding, and acoustic filtering. However, achieving scalable and precisely tunable bandgap properties across different length scales remains challenging. This study presents a user-friendly design framework for phononic metamaterials, enabling ultra-wide bandgap tunability (B/ω c ratios up to 172 %) across multiple frequency ranges and scales. Using finite element simulations of a Yablonovite-inspired unit cell, we establish a comprehensive parametric design space that illustrates how geometric parameters, such as sphere size and beam diameter, controls bandgap width and frequency. The scalability and robustness of the framework are validated through experimental testing on additively manufactured structures at both macro (10 mm) and micro (80 µm) scales, fabricated using Stereolithography and Two-Photon Polymerization. Transmission loss measurements, conducted with piezoelectric transducers and laser vibrometry, closely match simulations in the kHz and MHz frequency ranges, confirming the reliability and consistency of the bandgap behavior across scales. This work bridges theory and experiments at multiple scales, offering a practical methodology for the rapid design of phononic metamaterials and expanding their potential for diverse applications across a broad range of frequencies.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Evolution of Bonding and Magnetism via Changes in Valence Electron Count in CuFe 2– x Co x Ge 2

A series of solid solutions, CuFe 2–x Co x Ge 2 (x = 0, 0.2, 0.4, 0.8, and 1.0), have been synthesized by arc-melting and characterized by powder X-ray and neutron diffraction, magnetic measurements, Mössbauer spectroscopy, and electronic band structure calculations. All compounds crystallize in the CuFe 2 Ge 2 structure type, which can be considered as a three-dimensional framework built of fused MGe6 octahedra and MGe 5 trigonal bipyramids (M = Fe and Co), with channels filled by rows of Cu atoms. As the Co content (x) increases, the unit cell volume decreases in an anisotropic fashion: the b and c lattice parameters decrease while the a parameter increases. The changes in all the parameters are nearly linear, thus following Vegard’s law. CuFe 2 Ge 2 exhibits two successive antiferromagnetic (AFM) orderings, corresponding to the formation of a commensurate AFM structure, followed by an incommensurate AFM structure observed at lower temperatures. Additionally, as the Co content increases, the AFM ordering temperature (TN) gradually decreases, and only one AFM transition is observed for x ≥ 0.2. The magnetic behavior of unsubstituted CuFe 2 Ge 2 was found to be sensitive to the preparation method. The temperature-dependent zero-field 57 Fe Mössbauer spectra reveal two hyperfine split components that evolve in agreement with the two consecutive AFM orderings observed in magnetic measurements. In contrast, the field-dependent spectra obtained for fields ≥ 2 T reveal a parallel arrangement of the moments associated with the two crystallographically unique metal sites. Electronic band structure calculations and chemical bonding analysis reveal a mix of strong M–M antibonding and non-bonding states at the Fermi level, in support of the overall AFM ordering observed in zero field. The substitution of Co for Fe reduces the population of the M–M antibonding states and the overall density of states at the Fermi level, thus suppressing the T N value.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Resolving electron and hole transport properties in semiconductor materials by constant light-induced magneto transport

The knowledge of minority and majority charge carrier properties enables controlling the performance of solar cells, transistors, detectors, sensors, and LEDs. Here, we developed the constant light induced magneto transport method which resolves electron and hole mobility, lifetime, diffusion coefficient and length, and quasi-Fermi level splitting. We demonstrate the implication of the constant light induced magneto transport for silicon and metal halide perovskite films. We resolve the transport properties of electrons and holes predicting the material’s effectiveness for solar cell application without making the full device. The accessibility of fourteen material parameters paves the way for in-depth exploration of causal mechanisms limiting the efficiency and functionality of material structures. To demonstrate broad applicability, we further characterized twelve materials with drift mobilities spanning from 10 –3 to 10 3 cm 2 V –1 s –1 and lifetimes varying between 10 –9 and 10 –3 seconds. The universality of our method its potential to advance optoelectronic devices in various technological fields.

14 SOLAR ENERGY↗
DOE OSTI2020

Influence of Hydrogen and Oxygen on the Structure and Properties of Sputtered Magnesium Zirconium Oxynitride Thin Films

Nitride materials with mixed ionic and covalent bonding character and resulting good charge transport properties are attractive for optoelectronic devices. Recently, Mg-based ternary nitride materials were found to have large dielectric constants and high absorption coefficients with bandgaps appropriate for photovoltaic applications. However, their degenerate carrier concentrations still hinder their possible applications in solar cells and related optoelectronic devices. Therefore, further understanding and engineering of the parameters controlling the material properties of these ternary nitrides is highly desirable. In this paper we report that the structural, optical and electrical properties of magnesium zirconium oxynitride (MZNO) thin films synthesized by combinatorial sputtering with a wide range of cation compositions can be affected by incorporation of oxygen and hydrogen. Excess oxygen improved the crystallinity of MZNO thin films whereas hydrogen attracted oxygen and formed Mg-rich oxide layers at the grain boundaries which in turn reduced the conductivity. On the other hand, optical properties are more sensitive to the composition – both cation and anion ratios – rather than the presence of hydrogen. Compared to cation-stoichiometric MZNO (10 19 –10 20 cm -3 ), substantial reduction of carrier concentration down to ~10 14 cm -3 was achieved under Mg-rich conditions by supplying hydrogen during growth. Photoluminescence measurements showed that the films prepared with hydrogen were optoelectronically active. Overall, this study demonstrates that the material properties of MZN thin films can be significantly influenced by incorporation of oxygen and hydrogen.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Multiscale Modeling Framework for Lithium Nucleation in 3D Porous Carbon Anodes

Porous carbon scaffolds offer a promising route for mitigating non-uniform lithium (Li) plating to enhance the safety and longevity of Li metal batteries. However, the influence of microstructural morphology on Li nucleation is not well understood. Here, we present a multiscale modeling framework to investigate how the porous microstructure of carbon materials affects Li nucleation behavior. Ab initio molecular dynamics simulations quantify the nucleation energy barriers of Li on graphene as a function of Li content, surface curvature, and applied potential, providing key parameters for a classical nucleation theory (CNT) model. From macroscale half-cell simulations, we obtained Li concentration and electrical potential profiles to define boundary conditions for mesoscopic simulations. At the mesoscale, three distinct synthetic 3D microstructures with different porosities and characteristic feature sizes are generated to resolve local distributions of Li flux, current density, and mechanical stress. These outputs are integrated into the CNT model to map spatial variation in nucleation rates. Our findings reveal trade-offs between suppressing nucleation rates and achieving spatial uniformity, offering design guidelines for optimizing porous carbon anodes to balance nucleation control and mechanical integrity.

Materials science↗
DOE OSTI2024

Rapid Demonstration of Bremsstrahlung Diode Optimization

Optimization of the radiation pattern from a Bremsstrahlung target for a given application is possible by controlling the electron beam that impacts the high-atomic-number target. In this work, the electron beam is generated by a 13MV vacuum diode that terminates a coaxial magnetically insulted transmission line (MITL) on the HERMES-III machine at Sandia National Labs. Work by Sanford introduced a geometry for vacuum diodes that can control the flow within bounds. The "indented anode", as coined by Sanford, can straighten out the electron beam in a high-current diode that would otherwise be prone to beam pinching. A straighter beam will produce a more forwardly directed radiation pattern while a pinching electron beam will yield a focal point or hot spot on axis and a more diffuse radiation pattern. Either one of these may be desirable depending on the application. This work serves as a first attempt to optimize the radiation pattern in the former sense of collimating the radiation pattern given a limited parameter space. The optimization is attempted first using electromagnetic particle-in-cell simulations in the EMPIRE code suite. The setup of the models used in EMPIRE is discussed along with some basic theory behind some of the models used in the simulations such as anode heating and secondary ions. Theoretical work performed by Allen Garner and his students at Purdue is included here, which concerns the impact of collisions in these vacuum diodes. The EMPIRE simulations consider both an aggressive and a conservative design. The aggressive design is inherently riskier while the conservative design is chosen as something that, while still a risk, is more likely to perform as expected. The ultimate goal of this work was to validate the EMPIRE code results with experimental data. While the experiment that tested the diode designs proposed by the simulation results fell outside of the fiscal boundaries of this project (and for that reason the results of which are not included in this report), the hardware for the experiment was designed and drafted within those same fiscal boundaries, and is thus included in this report. However, there was yet another experiment performed in this project that tested a key feature of the diode: the hemispherical cathode. Those results are documented here as well, which show that the cathode tip is an important aspect to controlling the diode flow. A short series of simulations on this diode were also performed after the experiment in order to gain a better understanding of the effect of ions. on the flow pattern and faceplate dose profile.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Lithium-Ion Battery Design for Grid-Scale Energy Storage App

A software that delivers parameters from energy storage system (ESS) to container, rack, module and single cell design, as well as data analysis on arbitrage energy and frequency regulation of ESS in different regions, has been developed. The Lithium-ion Battery Design for Grid-scale Energy Storage App V1.0 has the capability to output the system, module and cell design with the energy, power, capacity, group method, cost of single cell, and single cell test protocol which break down from input energy storage system data in different regions. The default chemistry of the battery is LiFePO4 and graphite. The energy density of the graphite/LiFePO 4 pouch cell ranges from 100 Wh/kg to 200 Wh/Kg in the software. Graphite/LiFePO 4 pouch cell (up to 1Ah in lab) manufacturing line is also built and can be used to evaluate the test protocol, moreover, for electrolyte evaluation in other ESMI seedling projects. The software enables rapid prototyping to accelerate energy storage research, development, and manufacturing.

Liu, Dianying↗
NASA NTRS1976

Chemical vapor deposition growth

A laboratory type CVD reactor system with a vertical deposition chamber and sample pedestal heated by an external RF coil has been extensively modified by installation of mass flow controllers, automatic process sequence timers, and special bellows-sealed air-operated valves for overall improved performance. Various film characterization procedures, including classical metallography, SEM analyses, X ray diffraction analyses, surface profilometry, and electrical measurements (resistivity, carrier concentration, mobility, spreading resistance profiles, and minority-carrier lifetime by the C-V-t method) area used to correlate Si sheet properties with CVD parameters and substrate properties. Evaluation procedures and measurements are given. Experimental solar cell structures were made both in epitaxial Si sheet (on sapphire substrates) and in polycrystalline material on alumina substrates, the former to provide an indication of what might be an upper limit on performance of the latter. Preliminary results are given, as obtained in cell structures not specially designed to allow for the unique properties of the sheet material, and fabricated in material known to be far from optimum for photovoltaic performance. Low power conversion efficiencies have been obtained in the epitaxial as well as the polycrystalline Si sheet.

Ruth, R. P.↗
NASA NTRS1977

Charge and discharge profile

Some possible parameters which could be used to predict failures within packs of electrochemical cells based on measurements that are taken while the cells are cycling are discussed. Discharge and charge curves are presented and fitted to measure the efficiency of the cells in terms of voltage vs. time.

Mcdermott, P. P.↗
NASA NTRS1981

Effect of shear stress on cell cultures and other reactor problems

Anchorage dependent cell cultures in fluidized beds are tested. Feasibility calculations indicate the allowed parameters and estimate the shear stresses therein. In addition, the diffusion equation with first order reaction is solved for the spherical shell (double bubble) reactor with various constraints.

Schleier, H.↗
NASA NTRS1985

Numerical simulation of vortex breakdown

The breakdown of an isolated axisymmetric vortex embedded in an unbounded uniform flow is examined by numerical integration of the complete Navier-Stokes equations for unsteady axisymmetric flow. Results show that if the vortex strength is small, the solution approaches a steady flow and the vortex is stable. If the strength is large enough, the solution remains unsteady and a recirculating zone will appear near the axis, its form and internal structure resembling those of the axisymmetric breakdown bubbles with multi-cells observed by Faler and Leibovich (1978). For apppropriate combinations of flow parameters, the flow reveals quasi-periodicity. Parallel calculations with the quasi-cylindrical approximation indicate that so far as predicting of breakdown is concerned, its results coincide quite well with the results mentioned above. Both show that the vortex breakdown has little concern with the Reynolds number or with the critical classification of the upstream flow, at least for the lower range of Reynolds numbers.

Shi, X.↗
NASA NTRS1986

A flooded-starved design for nickel-cadmium cells

A somewhat analogous situation among groupings of alkaline fuel cells is described where the stochastic aspects were much more accurately documented and then it was illustrated how this problem was eliminated using straight forward principles of pore size engineering. This is followed by a suggested method of adapting these same design principles to nickel-cadmium cells. It must be kept in mind that when cells are cycled to typically twenty percent depth of discharge that eighty percent of the weight of the cell is simply dead weight. Some of this dead weight might be put to better use by trading it for a scheme that would increase the time during which the cell would be working more closely to its optimum set of operating parameters.

Thaller, L. H.↗
NASA NTRS1987

Fed-batch control based upon the measurement of intracellular NADH

A series of experiments demonstrating that on-line measurements of intracellular NADH by culture fluorescence can be used to monitor and control the fermentation process are described. A distinct advantage of intercellular NADH measurements over other monitoring techniques such as pH and dissolved oxygen is that it directly measures real time events occurring within the cell rather than changes in the environment. When coupled with other measurement parameters, it can provide a finer degree of sophistication in process control.

Armiger, W. B.↗
NASA NTRS1992

Steady state composition with low Fe(2+) concentrations for efficient O2 production by 'magma' electrolysis of lunar soils

Parameters are estimated for a hypothetical, well stirred, continuous-feed electrolytic cell that converts 20 percent of a lunar soil feedstock to O2 gas, 26 percent to Fe-Si metal, 13 percent to spinel, and 41 percent to slag. Advantages of a molten Fe-Si cathode for trapping metal on reduction, a relatively conductive steady-state composition in equilibrium with spinel (a proposed container material), and close electrodes (less than 1 cm cathode-anode distance) are discussed. To produce 1 ton of O2, about 6 MHW of energy are required for the electrolysis and IR heating within the melt, and another about 6 MHW may be introduced as waste heat through internal resistance of the electrodes. Thus, to produce 1 ton of O2 per 24 hours, about 0.5 MW of power delivered to the cell would be required.

Haskin, Larry A.↗
NASA NTRS1993

User's manual for the HYPGEN hyperbolic grid generator and the HGUI graphical user interface

The HYPGEN program is used to generate a 3-D volume grid over a user-supplied single-block surface grid. This is accomplished by solving the 3-D hyperbolic grid generation equations consisting of two orthogonality relations and one cell volume constraint. In this user manual, the required input files and parameters and output files are described. Guidelines on how to select the input parameters are given. Illustrated examples are provided showing a variety of topologies and geometries that can be treated. HYPGEN can be used in stand-alone mode as a batch program or it can be called from within a graphical user interface HGUI that runs on Silicon Graphics workstations. This user manual provides a description of the menus, buttons, sliders, and typein fields in HGUI for users to enter the parameters needed to run HYPGEN. Instructions are given on how to configure the interface to allow HYPGEN to run either locally or on a faster remote machine through the use of shell scripts on UNIX operating systems. The volume grid generated is copied back to the local machine for visualization using a built-in hook to PLOT3D.

Chan, William M.↗