Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,027 records · Page 57

Nuclear Thermal Propulsion Requirements Analysis of the ESAS Reference Human Mars Mission Architecture

The Nuclear Thermal Propulsion Mission and System Analysis (NTP MSA) Phase 2 Study was initiated by Marshall Space Flight Center’s (MSFC) Advanced Concepts Office (VP11) in December, 2005 in support of MSFC’s Nuclear Systems Office (VP31) NTP for Exploration Study. The Mission and Systems Analysis Study was task # 6 of a set of 14 tasks within the NTP for Exploration Study. The primary goal of the NTP MSA Phase 2 Study was to identify the range of potential NTP engine and vehicle requirements for NASA Exploration Systems Mission Directorate (ESMD) Mars human exploration reference mission.

mars↗

Enabling liquid vapor analysis using synchrotron VUV single photon ionization mass spectrometry with a microfluidic interface

Vacuum ultraviolet (VUV) single photon ionization mass spectrometry (SPI-MS) is a vacuum-based technique typically used for analysis of gas phase and solid samples, but not for liquids, due to the challenge in proposing volatile liquids in vacuum. In this work we introduce the first demonstration of in situ liquid analysis by integrating the System for Analysis at the Liquid Vacuum Interface (SALVI) microfluidic reactor into VUV SPI-MS. Four representative volatile organic compound (VOC) solutions were used to illustrate feasibility of liquid analysis. Our results reflect accurate mass identification of the VOC molecules and reliable determination of appearance energy (AE) that is consistent with ionization energy (IE) for gaseous species in literature as reported. This work validates that the vacuum-compatible SALVI microfluidic interface can be utilized at the synchrotron beamline and enable in situ research of gas-phase molecules evaporating off the surface of a liquid, which holds importance in the study of condensed matter chemistry.

47 OTHER INSTRUMENTATION↗

Root Cause Analysis of AC Overcurrent in July 2020 San Fernando Disturbance

On July 7 2020, approximately 1,000 MW reduction in solar photovoltaic (PV) output was experienced by the bulk power system in Southern California after a three-phase fault. Disturbance analysis indicates that instantaneous AC current caused inverter tripping. The projection of the root cause of AC overcurrent from the NERC report is that inverter current control is not tight. This letter provides a quantitative analysis on ac overcurrent and addresses the following questions: (i) what type of current controls may lead to ac overcurrent; and (ii) how controller parameters and grid strength influence ac overcurrent. Here, the letter provides frequency-domain analysis and time-domain simulation results of a grid-integrated inverter to illustrate the effect of control parameters and grid strength on ac overcurrent.

14 SOLAR ENERGY↗

Theory, Image Simulation, and Data Analysis of Chemical Release Experiments

The final phase of Grant NAG6-1 involved analysis of physics of chemical releases in the upper atmosphere and analysis of data obtained on previous NASA sponsored chemical release rocket experiments. Several lines of investigation of past chemical release experiments and computer simulations have been proceeding in parallel. This report summarizes the work performed and the resulting publications. The following topics are addressed: analysis of the 1987 Greenland rocket experiments; calculation of emission rates for barium, strontium, and calcium; the CRIT 1 and 2 experiments (Collisional Ionization Cross Section experiments); image calibration using background stars; rapid ray motions in ionospheric plasma clouds; and the NOONCUSP rocket experiments.

Wescott, Eugene M.↗

Terahertz dielectric analysis and spin-phonon coupling in multiferroic GeV 4 S 8

We present an investigation of the multiferroic lacunar spinel compound GeV 4 S 8 using time-domain terahertz spectroscopy. We find three absorptions which either appear or shift at the antiferromagnetic transition temperature, T N =17K, as S=1 magnetic moments develop on vanadium tetrahedra. Two of these absorptions are coupled to the magnetic state and one only appears below the Néel temperature, and is interpreted as a magnon. We also observe isosbestic points in the dielectric constant in both the temperature and frequency domains. Further, we perform an analysis on the isosbestic features to reveal an interesting collapse into a single curve as a function of both frequency and temperature, behavior which exists throughout the phase transitions. This analysis suggests the importance of spectral changes in the terahertz range which are linear in frequency and temperature.

36 MATERIALS SCIENCE↗

Phase separation at the dimer-superconductor transition in Ir 1-x Rh x Te 2

The detailed evolution of the local atomic structure across the (x, T) phase diagram of transition metal dichalcogenide superconductor Ir 1–x Rh x Te 2 (0≤x≤0.3, 10 K≤T≤300 K) is obtained from high quality x-ray diffraction data using the atomic pair distribution function (PDF) method. Observed hysteretic thermal structural phase transition from trigonal (P3¯m1) to triclinic (P1¯) dimer phase for low Rh content emphasizes intimate connection between the lattice and electronic properties. For superconducting samples away from the dimer/superconductor phase boundary structural transition is absent and the local structure remains trigonal down to 10 K. In the narrow range of compositions close to the boundary PDF analysis reveals structural phase separation, suggestive of weak first order character of the Rh-doping induced dimer-superconductor quantum phase transition. Samples from this narrow range show weak anomalies in electronic transport and magnetization, hallmarks of the dimer phase, as well as superconductivity albeit with incomplete diamagnetic screening. Furthermore, results suggest that the dimer and superconducting orders exist in the mutually exclusive spatial regions

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ensuring Solution Uniqueness in Three-Phase Power System State Estimation

This paper is concerned with the issue of potential non-unique solutions in three-phase state estimation. Theory of observability analysis for positive sequence power system state estimation is based on certain assumptions that avoid possibility of multiple solutions. Also, it is shown that observability of a positive sequence network remains independent of the network parameters or the operating state. When extending single-phase observability analysis directly to the three-phase case, this paper considers the possibility of converging to multiple solutions, i.e. solution non-uniqueness, even for cases where state estimator successfully converges. The study illustrates via numerical examples the likelihood of converging to entirely different solutions for certain network parameters. It also examines how the operating state, particularly under unbalanced loading, leads to solution non-uniqueness. The paper then describes an alternative approach to ensure a unique solution in three-phase state estimation. This method aims to accurately and uniquely estimate the state of any unbalanced three-phase system, irrespective of load imbalance, network configuration, existence of synchronous generators or transformers.

Power System State Estimation, Three-Phase, Distri↗

Demonstration of Active Combustion Control

The primary objective of this effort was to demonstrate active control of combustion instabilities in a direct-injection gas turbine combustor that accurately simulates engine operating conditions and reproduces an engine-type instability. This report documents the second phase of a two-phase effort. The first phase involved the analysis of an instability observed in a developmental aeroengine and the design of a single-nozzle test rig to replicate that phenomenon. This was successfully completed in 2001 and is documented in the Phase I report. This second phase was directed toward demonstration of active control strategies to mitigate this instability and thereby demonstrate the viability of active control for aircraft engine combustors. This involved development of high-speed actuator technology, testing and analysis of how the actuation system was integrated with the combustion system, control algorithm development, and demonstration testing in the single-nozzle test rig. A 30 percent reduction in the amplitude of the high-frequency (570 Hz) instability was achieved using actuation systems and control algorithms developed within this effort. Even larger reductions were shown with a low-frequency (270 Hz) instability. This represents a unique achievement in the development and practical demonstration of active combustion control systems for gas turbine applications.

Lovett, Jeffrey A.↗

Synthesis and structure of high-purity BaCe 0.25 Mn 0.75 O 3 : an improved material for thermochemical water splitting

Solar thermochemical hydrogen production (STCH) via redox-active metal oxides is an approach for direct solar-driven hydrogen generation typically using a high-temperature redox cycle involving refractory oxides and steam. Typical cycles involve high-temperature reduction of oxides to form oxygen vacancies, followed by lower temperature reaction between oxygen vacancies and steam where the oxide is re-oxidized and the steam is reduced to hydrogen. Only a few materials have demonstrated reversible cycling under the typically harsh STCH conditions (e.g. 1500°C reduction, 900°C re-oxidation) and critical questions remain on the true reversibility of non-stoichiometric multi-cation oxide systems, significantly hampered by the lack of single-phase samples for these material systems. To date, most STCH processes have relied on CeO 2 as a benchmark active material, but more recently, the 12R phase of BaCe 0.25 Mn 0.75 O 3 (BCM) has demonstrated greater hydrogen-generation potential at lower peak temperatures. However, previous reports of 12R-BCM have included large fractions, > 10 wt%, of secondary phases, which complicate analysis of the stability and performance. A comprehensive understanding of the redox mechanism and reversibility of the process in BCM can only be achieved with nearly single-phase samples which, to date, have been difficult to produce. Here two approaches to BCM synthesis are reported: solid state and sol–gel-based routes. It is demonstrated that both routes can be tuned to produce the 12R structure with > 97 wt% yield when annealed ≥1450°C. Herein synchrotron-based diffraction measurements of rhombohedral 12R-BCM enabled characterization of the anisotropy between thermal expansion along the c-axis and within the ab plane. The impact of high-temperature redox cycling on the stability and phase fraction of the 12R-BCM polytype was also investigated. Our results offer two viable routes for synthesis of high-purity 12R-BCM critically needed for evaluating the efficacy of BCM as a STCH material and validate its ability to split water at lower temperatures over extended numbers of redox cycles.

08 HYDROGEN↗

Phase-locked loops

The basic analysis and design procedures are described for the realization of analog phase-locked loops (APLL), hybrid phase-locked loops (HPLL), discrete phase-locked loops, and digital phase-locked loops (DPLL). Basic configurations are diagrammed, and performance curves are given. A discrete communications model is derived and developed. The use of the APLL as an optimum angle demodulator and the Kalman-Bucy approach to APLL design are discussed. The literature in the area of phase-locked loops is reviewed, and an extensive bibliography is given. Although the design of APLLs is fairly well documented, work on discrete, hybrid, and digital PLLs is scattered, and more will have to be done in the future to pinpoint the formal design of DPLLs.

Gupta, S. C.↗

Effects of large-scale wind driven turbulence on sound propagation

Acoustic measurements made in the atmosphere have shown significant fluctuations in amplitude and phase resulting from the interaction with time varying meteorological conditions. The observed variations appear to have short term and long term (1 to 5 minutes) variations at least in the phase of the acoustic signal. One possible way to account for this long term variation is the use of a large scale wind driven turbulence model. From a Fourier analysis of the phase variations, the outer scales for the large scale turbulence is 200 meters and greater, which corresponds to turbulence in the energy-containing subrange. The large scale turbulence is assumed to be elongated longitudinal vortex pairs roughly aligned with the mean wind. Due to the size of the vortex pair compared to the scale of the present experiment, the effect of the vortex pair on the acoustic field can be modeled as the sound speed of the atmosphere varying with time. The model provides results with the same trends and variations in phase observed experimentally.

Noble, John M.↗

Formation of a metastable ferromagnetic tau phase during containerless melt processing in Mn-Al-C alloys

This paper reports the production of a metastable ferromagnetic tau phase directly from the melt in Mn(0.55)Al(0.433)C(0.017), using a containerless processing method involving levitation melting followed by quenching. Using the results from differential thermal analysis measurements and an analysis of the phase equilibria, it was found that the minimum amount of undercooling level required for ferromagnetic metastable tau phase formation in this alloy was Delta T = 87 K. The attainment of this undercooling may be facilitated by the application of containerless melt processing.

Kim, Y. J.↗

High-speed x-ray phase contrast imaging and digital image correlation analysis of microscale shock response of an additively manufactured energetic material simulant

The performance of energetic materials subjected to dynamic loading significantly depends on their micro- and meso-scale structural morphology. The geometric versatility offered by additive manufacturing opens new pathways to tailor the performance of these materials. Additively manufactured energetic materials (AMEMs) have a wide range of structural characteristics with a hierarchy of length scales and process-inherent heterogeneities, which are hitherto difficult to precisely control. It is important to understand how these features affect AMEMs’ response under dynamic/shock loading. Therefore, temporally and spatially resolved measurements of both macroscopic behavior and micro- and meso-level processes influencing macroscopic behavior are required. In this paper, we analyze the shock compression response of an AMEM simulant loaded under several impact conditions and orientations. Furthermore, x-ray phase contrast imaging (PCI) is used to track features across the observed shock front and determine the linear shock velocity vs particle velocity equation of state, as well as to quantify the interior deformation fields via digital image correlation (DIC) analyses. Photon Doppler velocimetry is simultaneously used to measure the particle velocities of the specimens, which are consistent with those obtained from x-ray PCI. The DIC analyses provide an assessment of the average strain fields inside the material, showing that the average axial strain depends on the loading intensity and reaches as high as 0.23 for impact velocities up to 1.5 km/s. The overall results demonstrate the utility of x-ray PCI for probing “in-material” equation of state and interior strains associated with dynamic shock compression behavior of the AMEM simulant.

3D printing↗

Effects of long-term thermal aging on bulk and local mechanical behavior of ferritic-austenitic duplex stainless steels

Ferritic-austenitic duplex stainless steels (DSS) undergo significant thermal aging embrittlement in service in light water reactors. Specimens of cast CF–3 and CF–8 DSS have been laboratory aged for up to 17,200 h at four different temperatures (280, 320, 360, 400 °C) in order to characterize the aging evolution and mechanical properties. Standard Charpy V-Notch (CVN) impact testing and tensile testing are employed to measure the progression of embrittlement of the steels. Concurrently, nanoindentation measurements are performed to measure the hardening of the individual ferrite and austenite phases. Atom probe tomography (APT) analysis of the ferrite and austenite phases elucidates the relationship between spinodal decomposition of the ferrite and the mechanical effects of aging. The results are discussed to relate the effects of the local microstructure and property changes in the ferrite phase on the overall bulk mechanical evolution of these steels.

Schwarm, Samuel C.↗

An Investigation of Oxides of Tantalum Produced by Pulsed Laser Ablation and Continuous Wave Laser Heating

Recent progress has seen multiple Ta 2 O 5 polymorphs generated by different synthesis techniques. However, discrepancies arise when these polymorphs are produced in widely varying thermodynamic conditions and characterized using different techniques. This work aimed to characterize and compare Ta 2 O 5 particles formed at high and low temperatures using nanosecond pulsed laser ablation (PLA) and continuous wave (CW) laser heating of a local area of tantalum in either air or an 18 O 2 atmosphere. Scanning electron microscopy (SEM) and Raman spectroscopy of the micrometer-sized particles generated by PLA were consistent with either a localized amorphous Ta 2 O 5 phase or a similar, but not identical, crystalline β-Ta 2 O 5 phase. The Raman spectrum of the material formed at the point of CW laser impingement was in good agreement with the previously established ceramic “H-Ta 2 O 5 ” phase. TEM and electron diffraction analysis of these particles indicated the phase structure matched an oxygen-vacated superstructure of monoclinic H-Ta 2 O 5 . Further from the point of laser impingement, CW heating produced particles with a Raman spectrum that matched β-Ta 2 O 5 . We confirmed that the high-temperature ceramic phase characterized in previous work by Raman spectroscopy was the same monoclinic phase characterized in different work by TEM and could be produced by direct laser heating of metal in air.

36 MATERIALS SCIENCE↗

Experimental results on tracking performance of the MTDD Costas loop with UQPSK signal

The carrier tracking performance of the breadboard Costas Loop of the Multimegabit Telemetry Demodulator Detector System was tested with unbalanced quadriphase shift keying (UQPSK) signals. An S-band UQPSK modulator was built for the tests. The experimental results are very close to the theoretical rms phase error calculations. The test and analysis show that the rms phase error for UQPSK signals is less than 5 deg at the design point if the I-to-Q channel power ratio is larger than 6 dB.

Park, Y. H.↗