Search NASA⌕ Search

SEARCH · Search NASA

Results for “Layered cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Surface Oxygen Depletion of Layered Transition Metal Oxides in Li-Ion Batteries Studied by Operando Ambient Pressure X-ray Photoelectron Spectroscopy

A new operando spectro-electrochemical setup was developed to study oxygen depletion from the surface of layered transition metal oxide particles at high degrees of delithiation. An NCM111 working electrode was paired with a chemically delithiated LiFePO 4 counter electrode in a fuel cell-inspired membrane electrode assembly (MEA). A propylene carbonate-soaked Li-ion conducting ionomer served as an electrolyte, providing both good electrochemical performance and direct probing of the NCM111 particles during cycling by ambient pressure X-ray photoelectron spectroscopy. The irreversible emergence of an oxygen-depleted phase in the O 1s spectra of the layered oxide particles was observed upon the first delithiation to high state-of-charge, which is in excellent agreement with oxygen release analysis via mass spectrometry analysis of such MEAs. By comparing the metal oxide-based O 1s spectral features to the Ni 2p 3/2 intensity, we can calculate the transition metal-to-oxygen ratio of the metal oxide close to the particle surface, which shows good agreement with the formation of a spinel-like stoichiometry as an oxygen-depleted phase. This new setup enables a deeper understanding of interfacial changes of layered oxide-based cathode active materials for Li-ion batteries upon cycling.

25 ENERGY STORAGE↗

Modeling and validation of single-chamber microbial fuel cell cathode biofilm growth and response to oxidant gas composition

This work describes experiments and computational simulations to analyze single-chamber, air-cathode microbial fuel cell (MFC) performance and cathodic limitations in terms of current generation, power output, mass transport, biomass competition, and biofilm growth. Steady-state and transient cathode models were developed and experimentally validated. Two cathode gas mixtures were used to explore oxygen transport in the cathode: the MFCs exposed to a helium-oxygen mixture (heliox) produced higher current and power output than the group of MFCs exposed to air or a nitrogen-oxygen mixture (nitrox), indicating a dependence on gas-phase transport in the cathode. Multi-substance transport, biological reactions, and electrochemical reactions in a multi-layer and multi-biomass cathode biofilm were also simulated in a transient model. The transient model described biofilm growth over 15 days while providing insight into mass transport and cathodic dissolved species concentration profiles during biofilm growth. Lastly, simulation results predict that the dissolved oxygen content and diffusion in the cathode are key parameters affecting the power output of the air-cathode MFC system, with greater oxygen content in the cathode resulting in increased power output and fully-matured biomass.

59 BASIC BIOLOGICAL SCIENCES↗

Structure for implementation of back-illuminated CMOS or CCD imagers

A structure for implementation of back-illuminated CMOS or CCD imagers. An epitaxial silicon layer is connected with a passivation layer, acting as a junction anode. The epitaxial silicon layer converts light passing through the passivation layer and collected by the imaging structure to photoelectrons. A semiconductor well is also provided, located opposite the passivation layer with respect to the epitaxial silicon layer, acting as a junction cathode. Prior to detection, light does not pass through a dielectric separating interconnection metal layers.

Pain, Bedabrata↗

Can Cobalt Be Eliminated from Lithium-Ion Batteries?

Following the discovery of LiCoO 2 (LCO) as a cathode in the 1980s, layered oxides have enabled lithium-ion batteries (LIBs) to power portable electronic devices that sparked the digital revolution of the 21st century. Since then, LiNi x Mn y Co z O 2 (NMC) and LiNi x Co y Al z O 2 (NCA) have emerged as the leading cathodes for LIBs in electric vehicle (EV) application and have become crucial components in the fight against global warming. However, the surging demand for LIBs has led to an extremely tight supply. The EV sector has already dominated the LIB market, even though EV sales were only 2–3% of total passenger vehicle sales in 2020. EV sales are expected to grow 10-fold by the end of this decade, and close to 90% of the total LIB demand will come from the EV sector. As a result, LIB manufacturers must aggressively ramp up cell production to keep pace with the immense growth of the EV market, a quest that brings scrutiny to the cost and sustainability of current LIB manufacturing practices. Here, cathodes are a critical component that largely determines the energy density and 40–50% of the total cell cost in LIBs. Rigorous consideration of the cathode performance and material cost is crucial in sustaining EV adoption. In this Viewpoint, we discuss why using cobalt in cathodes is unsustainable in the long run and highlight the features of cobalt-free cathodes.

25 ENERGY STORAGE↗

Atomic-scale tuned interface of nickel-rich cathode for enhanced electrochemical performance in lithium-ion batteries

The Ni-rich layered LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC6 22 ) is one promising cathode for lithium-ion batteries (LIBs), but suffers from poor cycling stability under high cutoff potentials. The performance degradation was reflected as capacity fading and voltage drop, having their roots in instable interface of NMC622. Aimed at improving interfacial stability, in this study, we deposited nanoscale ZrO 2 coatings conformally over NMC622 cathodes using atomic layer deposition (ALD). We found that, under a high cutoff voltage (4.5 V), the ALD ZrO 2 coatings evidently improved the performance of NMC622 cathode, showing better cyclability and higher sustainable capacity. In addition, the ALD coatings dramatically boosted the rate capability of NMC622. All these compelling performance results are ascribed to the atomic-scale tunable ZrO 2 coatings via ALD, which create stable interface and thereby inhibit unfavorable evolutions. In the study, we utilize a suite of characterization tools and various analyses to clarify the effects of ALD ZrO 2 coatings. This study will be helpful for improving the performance of nickel-rich cathodes via interfacial engineering using ALD.

25 ENERGY STORAGE↗

Investigation of the Cathode–Catalyst–Electrolyte Interface in Aprotic Li–O 2 Batteries

Enabled by a unique integrated fabrication and characterization platform, X-ray photoelectron spectroscopy (XPS) studies reveal the formation of a thin solid electrolyte interphase (SEI) layer on a Li–O2 cathode after the first cycle. Subsequent cycling indicates that this SEI layer is very stable in terms of both chemistry and morphology, even after extensive cycling, preserving reversibility at the cathode/electrolyte interface. Remarkably, even after cell failure, replacement of the lithium anode resulted in recovery of the cycling behavior with the same cathode. These results demonstrate that chemical stabilization of the cathode/electrolyte interface promotes long-term operation of DMSO-based Li–O2 Ru-catalyzed batteries. Characterization of the Li anode surface reveals electrolyte decomposition, and a partial mechanism is proposed for the observed chemical composition of the cathode SEI. These studies are enabled by conformal deposition of a heterogeneous OER catalyst on a freestanding, binder-free, mesoporous, carbon-based Li–O2 cathode with high capacity and long-term cycling stability.

25 ENERGY STORAGE↗

Resolving Chemical and Spatial Heterogeneities at Complex Electrochemical Interfaces in Li-Ion Batteries

The high specific capacities of Ni-rich transition metal oxides have garnered immense interest for improving the energy density of Li-ion batteries (LIBs). Despite the potential of these materials, Ni-rich cathodes suffer from interfacial instabilities that lead to crystallographic rearrangement of the active material surface as well as the formation of a cathode electrolyte interphase (CEI) layer on the composite during electrochemical cycling. While changes in crystallographic structure can be detected with diffraction-based methods, probing the chemistry of the disordered, heterogeneous CEI layer is challenging. In this work, we use a combination of ex situ solid-state nuclear magnetic resonance (SSNMR) spectroscopy and X-ray photoemission electron microscopy (XPEEM) to provide chemical and spatial information, on the nanometer length scale, on the CEI deposited on LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) composite cathode films. XPEEM elemental maps offer insight into the lateral arrangement of the electrolyte decomposition products that comprise the CEI and paramagnetic interactions (assessed with electron paramagnetic resonance (EPR) and relaxation measurements) in 13 C SSNMR provide information on the radial arrangement of the CEI from the NMC811 particles outward. Using this approach, here we find that LiF, Li 2 CO 3 , and carboxy-containing structures are directly appended to NMC811 active particles, whereas soluble species detected during in situ 1 H and 19 F solution NMR experiments (e.g., alkyl carbonates, HF, and vinyl compounds) are randomly deposited on the composite surface. We show that the combined approach of ex situ SSNMR and XPEEM, in conjunction with in situ solution NMR, allows spatially-resolved, molecular-level characterization of paramagnetic surfaces and new insights into electrolyte oxidation mechanisms in porous electrode films.

36 MATERIALS SCIENCE↗

Tuning Two Interfaces with Fluoroethylene Carbonate Electrolytes for High-Performance Li/LCO Batteries

Various electrolytes have been reported to enhance the reversibility of Li metal electrodes. However, for these electrolytes, concurrent and balanced control of Li metal and positive electrode interfaces is a critical step toward fabrication of high performance Li metal batteries. Here, we report the tuning of Li metal and lithium cobalt oxide (LCO) interfaces with fluoroethylene carbonate (FEC)-containing electrolytes to achieve high cycling stability of Li/LCO batteries. Reversibility of Li metal electrode is considerably enhanced for electrolytes with high FEC contents, confirming the positive effect of FEC on the stabilization of Li metal. electrode. However, for FEC content of 50 wt% and above, the discharge capacity is significantly reduced due to the formation of a passivation layer on the LCO cathodes. Using balanced tuning of the two interfaces, stable cycling over 350 cycle at 1.5 mA cm-2 is achieved for an Li/LCO cell with 1M PF6 FEC/DMC=30/70 electrolyte. The enhanced reversibility of the Li metal electrode is associated with the formation of LiF and polycarbonate in the FEC-derived solid electrolyte interface (SEI) layer. In addition, electrolytes with high FEC content lead to lateral Li deposition on the sides of Li deposits and larger dimensions of rod-like Li deposits, suggesting the elastic and ion conductive nature of the FEC-derived SEI layer.

Lee, Jinhong↗

2D Ni 0.25 Mn 0.75 O 2 : A high-performance cathode for multivalent ion batteries

Although Li-ion batteries have driven portable energy storage in recent decades, there is increasing concern about their safety, cost, and abundance of constituents. Multivalent ion batteries (MVIBs) have the potential to remedy these issues, but they are limited by the currently known MVIB cathodes, which fail to deliver unanimously favorable voltage, energy density, and diffusion kinetics. Here we used density functional theory (DFT) to model the performance of Li, Na, Mg, Ca, and Al ions when paired with 2D Ni 0.25 Mn 0.75 O 2 , a novel cathode that uses increased layer separation to improve on the kinetics of its 3D analog. Our calculations yielded maximum voltages of 3.38 V for Na and 2.7 V for Ca, outperforming 2D Na x MnO 2 and Na x NiO 2 . Diffusion barriers for Li, Na, and Ca are below 300 meV, comparable to existing battery technology and the endpoint 2D cathodes; meanwhile, Mg and Al have prohibitively high diffusion barriers, implying their incompatibility with this cathode. Lastly, density of states calculations and Bader charge analysis show that the cathode becomes conducting following ion adsorption, which is necessary for high-rate performance. 2D Ni 0.25 Mn 0.75 O 2 maintains performance seen with other 2D transition metal oxides while increasing cathode conductivity, indicating that it is a promising candidate for experimental investigation with Li, Na, and Ca ions.

25 ENERGY STORAGE↗

Effects of bubbles on the electrochemical behavior of hydrogen-evolving Si microwire arrays oriented against gravity

The size-distribution, coverage, electrochemical impedance, and mass-transport properties of H 2 gas-bubble films were measured for both planar and microwire-array platinized n + -Si cathodes performing the hydrogen-evolution reaction in 0.50 M H 2 SO 4 (aq). Inverted, planar n + -Si/Ti/Pt cathodes produced large, stationary bubbles which contributed to substantial increases in ohmic potential drops. In contrast, regardless of orientation, microwire array n + -Si/Ti/Pt cathodes exhibited a smaller layer of bubbles on the surface, and the formation of bubbles did not substantially increase the steady-state overpotential for H 2 (g) production. Experiments using an electroactive tracer species indicated that even when oriented against gravity, bubbles enhanced mass transport at the electrode surface. Microconvection due to growing and coalescing bubbles dominated effects due to macroconvection of gliding bubbles on Si microwire array cathodes. Electrodes that maintained a large number of small bubbles on the surface simultaneously exhibited low concentrations of dissolved hydrogen and small ohmic potential drops, thus exhibiting the lowest steady-state overpotentials. The results indicate that microstructured electrodes can operate acceptably for unassisted solar-driven water splitting in the absence of external convection and can function regardless of the orientation of the electrode with respect to the gravitational force vector.

25 ENERGY STORAGE↗

Strain-driven surface reconstruction and cation segregation in layered Li(Ni 1– x – y Mn x Co y )O 2 (NMC) cathode materials

The composition, structure and phase transformations occurring on cathode surfaces greatly affect the performance of Li-ion batteries. Li-Ion diffusion and surface–electrolyte interaction are two major phenomena that impact the capacity and cell impedance. The effects of surface reconstruction (SR) of cathode materials on the performance of Li-ion batteries are of current interest. However, the origin and evolution of the SR are still not well understood. In this work, density functional theory (DFT) calculations are used to investigate the processes taking place during surface segregation and reconstruction. Facet dependent segregation was found in Li(Ni 1– x – y Mn x Co y )O 2 (NMC) cathodes. Specifically, Co tends to segregate to the (104) surface of the primary particles within the transition metal layer, while Ni ions tend to segregate to the (012) surface in the Li layer, forming a SR. Experimental evidence shows the SR to be epitaxial with the bulk of the as-synthesized material, and the new SR phase is pinned to the NMC unit cell leading to a strained SR. Here, we demonstrate that strain can stabilize a spinel structure of the SR layers. Understanding the effects of surface strain opens a new avenue for the design of cathode materials with enhanced surface properties.

25 ENERGY STORAGE↗

Enabling Stable Cycling of 4.2 V High-Voltage All-Solid-State Batteries with PEO-Based Solid Electrolyte

Poly(ethylene oxide) (PEO)-based solid electrolytes are expected to be exploited in solid-state batteries with high safety. Its narrow electrochemical window, however, limits the potential for high voltage and high energy density applications. In this paper, the electrochemical oxidation behavior of PEO and the failure mechanisms of LiCoO 2 -PEO solid-state batteries are studied. It is found that although for pure PEO it starts to oxidize at a voltage of above 3.9 V versus Li/Li + , the decomposition products have appropriate Li + conductivity that unexpectedly form a relatively stable cathode electrolyte interphase (CEI) layer at the PEO and electrode interface. The performance degradation of the LiCoO 2 -PEO battery originates from the strong oxidizing ability of LiCoO 2 after delithiation at high voltages, which accelerates the decomposition of PEO and drives the self-oxygen-release of LiCoO 2 , leading to the unceasing growth of CEI and the destruction of the LiCoO 2 surface. When LiCoO 2 is well coated or a stable cathode LiMn 0.7 Fe 0.3 PO 4 is used, a substantially improved electrochemical performance can be achieved, with 88.6% capacity retention after 50 cycles for Li 1.4 Al 0.4 Ti 1.6 (PO 4 ) 3 coated LiCoO 2 and 90.3% capacity retention after 100 cycles for LiMn 0.7 Fe 0.3 PO 4 . The results suggest that, when paired with stable cathodes, the PEO-based solid polymer electrolytes could be compatible with high voltage operation.

25 ENERGY STORAGE↗

Tuning Surface Stoichiometry of SOFC Electrodes at the Molecular and Nano-scale for Enhanced Performance and Durability

This project achieved the following objectives. Different cation segregation behaviors of different common SOFC cathodes, including La 0.6 Sr 0.4 Co0.2Fe 0.8 O 3-δ (LSCF), Sr 0.5 Sm 0.5 O 3-δ (SSC), and PrBa 0.5 Sr 0.5 Co 1.5 Fe 0.5 O5 +δ (PBSCF), were determined. We showed how oxygen partial pressure and gas impurities impact the stability of SOFC cathodes. We developed atomic layer deposition (ALD) coating techniques for electrodes and showed that by introducing different elements and different ALD oxidizers, electrode surface chemistry can be altered, resulting in enhanced oxygen reduction kinetics. In addition, we developed solution infiltration technique to enhance performance and durability of electrodes. Different infiltrates as well as different thermal treatment processes were screened to identify the optimal surface modification process that yields both low impedance and high durability. The modified cathode shows excellent stability and has a low area specific resistance (ASR) of only 0.2 Ωcm 2 at 600 °C after over 2000 hours of operation. Further, we developed ceramic anodes, SrFe(Co,Mo)O 3 (SFCM) and SrFe(Ni,Mo)O 3 (SFNM), and enhanced anode oxidation kinetics by solution infiltration or in situ catalyst exsolution from the ceramic anode surface. The modified anodes showed improved performance in full SOFCs, and the optimized anode modification shows high stability for over 400 hours at 550 °C. Moreover, the modified anode also demonstrates high durability in methane. This work provides fundamental understanding of electrode surface chemistry and demonstrates a simple, facile, cost-effective approach to enhance catalytic activity and durability of SOFC electrodes.

20 FOSSIL-FUELED POWER PLANTS↗

Probing Electrochemically Induced Structural Evolution and Oxygen Redox Reactions in Layered Lithium Iridate

In order to exploit electrochemical capacity beyond the traditionally-utilized transition metal redox reactions in lithium-metal-oxide cathode materials, it is necessary to understand the role that oxygen ions play in the charge compensation mech-anisms, i.e., to know the conditions triggering electron transfer on the oxygen ions and whether this transfer is correlated with battery capacity. Theoretical and experimental investigations of a model cathode material, Li-rich layered Li 2 IrO 3 , have been performed to study the structural and electronic changes induced by electrochemical delithiation in a lithium-ion cell. First-principles density functional theory (DFT) calculations were used to compute the voltage profile of a Li/Li 2-x IrO 3 cell at various states of charge, and the results were in good agreement with electrochemical data. Electron energy loss spectroscopy (EELS), X-ray absorption near-edge spectroscopy (XANES), resonant/non-resonant X-ray emission spectroscopy (XES), and first principles core-level spectra simulations using the Bethe Salpeter Equation (BSE) approach were used to probe the change in oxygen electronic states over the $x$ = 0 to 1.5 range. The correlated Ir M 3 -edge XANES and O K-edge XANES data provided evidence that oxygen hole states form during the early stage of delithiation at ~3.5 V due to the interaction between O $p$ and Ir $d$ states, with Ir oxidation being the dominant source of electrochemical capacity. At higher potentials, the charge capacity was predominantly attributed to oxidation of the O 2- ions. It is argued that the emergence of oxygen holes alone is not necessarily indicative of electrochemical capacity beyond transition metal oxidation, since oxygen hole states can appear as a result of enhanced mixing of O $p$ and Ir $d$ states. Prevailing mechanisms accounting for the oxygen redox mechanism in Li-rich materials were examined by theoretical and experimental X-ray spectroscopy; however, no unambiguous spectroscopic signatures of oxygen dimer interaction or non-bonding oxygen states were identified.

25 ENERGY STORAGE↗

Modified High‐Nickel Cathodes with Stable Surface Chemistry Against Ambient Air for Lithium‐Ion Batteries

Abstract High‐Ni layered oxides are promising next‐generation cathodes for lithium‐ion batteries owing to their high capacity and lower cost. However, as the Ni content increases over 70 %, they have a high dynamic affinity towards moisture and CO 2 in ambient air, primarily reacting to form LiOH, Li 2 CO 3 , and LiHCO 3 on the surface, which is commonly termed “residual lithium”. Air exposure occurs after synthesis as it is common practice to handle and store them under ambient conditions. The air exposure leads to significant performance losses, and hampers the electrode fabrication, impeding their practical viability. Herein, we show that substituting a small amount of Al for Ni in the crystal lattice notably improves the chemical stability against air by limiting the formation of LiOH, Li 2 CO 3 , LiHCO 3 , and NiO in the near‐surface region. The Al‐doped high‐Ni oxides display a high capacity retention with excellent rate capability and cycling stability after being exposed to air for 30 days.

You, Ya↗

The Interaction between Cu and Fe in P2-Type Na x TMO 2 Cathodes for Advanced Battery Performance

Recently, Cu element has been introduced into layered sodium transition metal oxides (NaxTMO2) as cathode materials for sodium ion batteries to engineer rate and cycling performance. To study the unique role provided by Cu, we designed, synthesized and tested four different compositions of P2-type Nax(MnyFezCo1-y-z)O2 and three compositions of P2-type Nax(MnyFezCu1-y-z)O2 cathode materials. When cycled in the full voltage range of 1.5~4.5 V under different rates 0.1 C, 1 C and 10 C, the cyclability of MnFeCu-based compounds is better than that of MnFeCo-based ones. Using X-ray diffraction, we observed the P2 to O2-like phase transition of MnFeCu-based materials upon charging and studied its influence on battery performance. Limiting the P2-O2 phase transition delivers less capacity, but improves cyclability. By DFT simulations, we showed that different Na diffusivity and site preference in the high voltage phase contribute to the difference in the electrochemical performances of these cathode materials.

25 ENERGY STORAGE↗

An in situ formed inorganic conductive network enables high stability and rate capability of single-crystalline nickel-rich cathodes

Single-crystalline Ni-rich cathodes are promising for the next generation of high-energy-density Li-ion batteries due to their better capacity retention than their polycrystalline counterparts. However, there is still much room for improving the electrochemical performances when considering their surface degradation and severe kinetic hindrance during cycling. Herein, we report a strategy to construct an in situ formed robust Li-conductive Li 3 PO 4 layer on the surface of cathode particles. This Li-conductive layer significantly increases the Li-ion diffusion coefficients and suppresses detrimental surface phase transformation. In situ XRD reveals that the improved kinetics alleviate the local stress at high voltage. The as-prepared single-crystalline LiNi 0.83 Co 0.12 Mn 0.05 O 2 delivers good durability (96.8% after 100 cycles at 1C) and excellent rate capability (177.08 mA h g -1 at 5C). Here, this work provides a facile and efficient strategy to improve the cycling performance and boost the rate capability of single-crystalline Ni-rich cathodes.

25 ENERGY STORAGE↗