Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fusion Science”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

A line-imaging velocity interferometer technique for shock diagnostics without x-ray preheat limitation

A study was conducted with a line-imaging velocity interferometer on sandwich targets at the Shen Guang-III prototype laser facility in China, with the goal of eliminating the preheat effect. A sandwich target structure was used to reduce the x-ray preheat limitation (radiation temperature {approx}170 eV) in a radiative drive shock experiment. With a thick ablator, the preheat effect appeared before the shock arrived at the window. After adding a shield layer of high-Z material on the ablator, x-rays which penetrated the ablator were so weak that the blank-out effect could not be measured. This experiment indicates that the sandwich target may provide a valuable technique in experiments such as equation of state and shock timing for inertial confinement fusion studies.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Inhibited Aluminization of an ODS FeCr Alloy

Aluminide coatings are of interest for fusion energy applications both for compatibility with liquid Pb-Li and to form an alumina layer that acts as a tritium permeation barrier. Oxide dispersion strengthened (ODS) ferritic steels are a structural material candidate for commercial reactor concepts expected to operate above 600 C. Aluminizing was conducted in a laboratory scale chemical vapor deposition reactor using accepted conditions for coating Fe- and Ni-base alloys. However, the measured mass gains on the current batch of ODS Fe-14Cr were extremely low compared to other conventional and ODS alloys. After aluminizing at two different Al activities at 900 C and at 1100 C, characterization showed that the ODS Fe-14Cr specimens formed a dense, primarily AlN layer that prevented Al uptake. This alloy batch contained a higher (> 5000 ppma) N content than the other alloys coated and this is the most likely reason for the inhibited aluminization. Other factors such as the high O content, small ({approx} 140 nm) grain size and Y-Ti oxide nano-clusters in ODS Fe-14Cr also could have contributed to the observed behavior. Examples of typical aluminide coatings formed on conventional and ODS Fe- and Ni-base alloys are shown for comparison.

36 MATERIALS SCIENCE↗

Calibration of a mesoscale tritium transport model for ceramic breeder materials in TMAP8 using experimental data

Due to the scarcity of the long-term external tritium supply, lithium-containing breeder materials are used in the blanket of fusion reactors to produce tritium faster than the deuterium-tritium fusion reaction consumes it. A cellular breeder is a promising material with higher lithium density and thermal conductivity than conventional ceramic pebbles and enhanced tritium extraction with interconnected pores. Although several experimental and modeling efforts have improved our understanding of tritium transport, the exact mechanisms governing tritium release from breeder materials are still unknown. As a result, current models cannot reliably assess the tritium breeding capabilities of cellular breeder materials. This work presents a tritium transport multiphysics model and calibrates it using experimental data of deuterium absorption and desorption from cellular breeder materials at different temperatures and pressures. This model accounts for ceramic and pore diffusion, trapping and detrapping, and several surface reactions at the pore surface. After calibrating the model and performing sensitivity analysis, we discuss pre-dominant mechanisms governing tritium release from cellular breeder materials. The model is part of the Tritium Migration Analysis Program [TMAP8], a multiscale, multiphysics framework for tritium transport based on the finite element multiphysics framework MOOSE. This study demonstrates some of TMAP8’s capabilities and provides insight into the mechanisms governing tritium transport in cellular ceramic breeder materials.

08 HYDROGEN↗

Hydrogen and deuterium permeation in Hastelloy N

Hastelloy N was chosen as the fluoride salt-contacting structural material for the Molten Salt Reactor Experiment due to its excellent compatibility with the fuel salt FLiBe. FLiBe is currently investigated for several advanced fusion and fission reactor concepts where tritium generation in the FLiBe is anticipated. Knowledge of hydrogen transport properties through Hastelloy N is important to understand how tritium would permeate through this material and result in an unintentional release. In this study, the hydrogen and deuterium permeability, diffusivity, and solubility were measured from 500 to 700 °C at a primary-side pressure of 10 kPa in a well-characterized sample of Hastelloy N. The prepared polycrystalline Hastelloy N had C and O impurities present on the surface. These impurities were investigated using Auger Emission Spectroscopy and Ar depth profiling. Here, the adventitious C was removed upon the first Ar sputter cycle whereas O persisted deeper into the sample. For permeation experiments, applied deuterium pressures ranged from 13 Pa to 100 kPa and deuterium transport remained in the diffusion-limited regime (J ∝ P 0.5 ) throughout the pressure range examined. Two methods are employed to measure the effective hydrogen and deuterium diffusivity: rise and decline. The decline method produced improved statistical model fits for calculating the effective diffusion coefficient compared to the rise method. The resultant transport properties compared well to published values for other nickel alloys.

08 HYDROGEN↗

Multi-fidelity equations of state and transport coefficient datasets for pulsed-power applications

Reliably simulating experiments relevant to the National Nuclear Security Administration (NNSA) requires a detailed description of material properties across a wide range of conditions. Such properties include the equations of state, charged-particle transport coefficients, and optical properties like the opacity. Together, these properties make up the material models used in radiation-magnetohydrodynamic simulations of nuclear fusion experiments. Many of these models do not incorporate uncertainties in the data used to produce them. It is unknown whether these uncertainties significantly impact the interpretation of simulation results and diagnostics. The purpose of this work is to quantify how such uncertainties impact simulations of pulsed-power experiments. We accomplished this task by first assessing discrepancies between approaches used to generate the data. This included bringing together members of the high-energy-density community spanning the three NNSA laboratories and multiple universities. Then, using these data, we developed a general framework that systematically incorporates physical uncertainties within the material models suitable for uncertainty quantification analyses. The framework utilizes machine learning, Bayesian inference, and incorporates multi-fidelity datasets. We demonstrated the framework by quantifying the impact that material model uncertainties have on simulations of pulsed-power experiments underway on Z at Sandia National Laboratories. As a result of this work, we discovered that modest uncertainties in material models (roughly 20%) correspond to significant uncertainties in the outputs from simulations. Our framework has enabled rapid construction of material models through an automated procedure and allows for the generation of material models of interest to the NNSA.

36 MATERIALS SCIENCE↗

Crystallographic and temperature effects in low-energy collisions for plasma–material interactions

The interaction of plasma with materials is critical for the fundamental understanding of non-equilibrium processes and their wide application. Recent achievements in fusion energy research emphasize the importance of this problem. Because modelling and predicting plasma–material interactions (PMI) require considering a tremendous number of single plasma particle–surface interaction events, this type of modelling was, until recently, possible only within a binary collision approximation (BCA). The BCA approach considers materials as uniform temperature-insensitive media. The research presented here addresses the PMI problem within an atomistic-based approach for the first time at a statistically significant level. Approximately 10 5 molecular dynamics trajectories were generated for 100 eV deuterium ions interacting with a tungsten surface. The research demonstrated the critical importance of incorporating the discrete lattice structure of matter into the model. Deuterium penetration depth and fraction of backscattered deuterium ions strongly depend on the surface orientation, the impact incident ion directions, and the ions’ initial positions. On average, the BCA-based calculations underestimate the penetration depth by a factor of two or more, and the fraction of backscattered atoms is overestimated by a factor of two or more. As a result, increasing the material temperature from 500 to 3000 K reduces penetration depth by about 30% and increases the fraction of backscattered atoms by 250%.

36 MATERIALS SCIENCE↗

Measurement of the{sup 3}He permeability of DT-filled fused silica inertial confinement fusion (ICF) targets to study the effects of{sup 3}He on neutron emission during implosion

A set of laser implosion experiments were conducted at the OMEGA laser at the Univ. of Rochester, Laboratory for Laser Energetics (LLE) to study the effect of He concentration in DT-filled target shells on fusion yield in ICF implosions.. Eleven laser fusion shells consisting of 1100-{mu}m diameter, hollow, fused silica spheres with 4.6 to 4.7-{mu}m-thick walls were loaded with 520 kPa of deuterium-tritium (DT) and then with {sup 3}He (101.3 or 520 kPa). The {sup 3}He permeabilities of the shells were determined by measuring the pressure rate of rise into a system with known volume. A mathematical method was developed that relied on the experimental fill pressure and time, and the rate of rise data to solve differential equations using MathCAD to simultaneously calculate {sup 3}He permeability and initial {sup 3}He partial pressure inside the shell. Because of the high permeation rate for {sup 3}He out of the shells compared to that for DT gas, shells had to be recharged with {sup 3}He immediately before being laser imploded or 'shot' at LLE. The {sup 3}He partial pressure in each individual shell at shot time was calculated from the measured {sup 3}He permeability. Two different partial pressures of {sup 3}He inside the shell were shown to reduce neutron and gamma yields during implosion. (authors)

36 MATERIALS SCIENCE↗

Morphologies of tungsten nanotendrils grown under helium exposure

Nanotendril “fuzz” will grow under He bombardment under tokamak-relevant conditions on tungsten plasma-facing materials in a magnetic fusion energy device. We have grown tungsten nanotendrils at low (50 eV) and high (12 keV) He bombardment energy, in the range 900–1000 °C, and characterized them using electron microscopy. Low energy tendrils are finer (~22 nm diameter) than high-energy tendrils (~176 nm diameter), and low-energy tendrils have a smoother surface than high-energy tendrils. Cavities were omnipresent and typically ~5–10 nm in size. Oxygen was present at tendril surfaces, but tendrils were all BCC tungsten metal. Electron diffraction measured tendril growth axes and grain boundary angle/axis pairs; no preferential growth axes or angle/axis pairs were observed, and low-energy fuzz grain boundaries tended to be high angle; high energy tendril grain boundaries were not observed. We speculate that the strong tendency to high-angle grain boundaries in the low-energy tendrils implies that as the tendrils twist or bend, strain must accumulate until nucleation of a grain boundary is favorable compared to further lattice rotation. Finally, the high-energy tendrils consisted of very large (>100 nm) grains compared to the tendril size, so the nature of the high energy irradiation must enable faster growth with less lattice rotation.

36 MATERIALS SCIENCE↗

Solidification modes during additive manufacturing of steel revealed by high-speed X-ray diffraction

Solidification during fusion-based additive manufacturing (AM) is characterized by high solidification velocities and large thermal gradients, two factors that control the solidification mode of metals and alloys. Using two synchrotron-based, in situ setups, we perform high-speed X-ray diffraction measurements to investigate the impact of the solidification velocities and thermal gradients on the solidification mode of a hot-work tool steel over a wide range of thermal conditions of relevance to AM of metals. The solidification mode of primary δ-ferrite is observed at a cooling rate of 2.12x10 4 K/s, and at a higher cooling rate of 1.5x10 6 K/s, δ-ferrite is sup-pressed, and primary austenite is observed. The experimental thermal conditions are evaluated and linked to a Kurz-Giovanola-Trivedi (KGT) based solidification model. The modelling results show that the predictions from the multicomponent KGT model agree with the experimental observations. This work highlights the role of in situ XRD measurements for a fundamental understanding of the microstructure evolution during AM and for vali-dation of computational thermodynamics and kinetics models, facilitating parameter and alloy development for AM processes.

36 MATERIALS SCIENCE↗

Forward Modeling of Gamma Reaction History Signatures From Anticipated Deuterium-Tritium Filled MagLIF Implosions on Sandia’s Z-Machine

Nuclear reaction history measurements provide a bang time and burn width of Inertial Confinement Fusion (ICF) implosions and are essential for understanding implosion performance to constrain ICF capsule design. When fusion fuel contains Deuterium (D) and Tritium (T) gas, reaction history is informed by measuring the 16.75 MeV gamma rays generated from the D(T,γ) 5 He reaction. Such DT based reaction history measurements have not been made on the Magnetized Laser Inertial Fusion (MagLIF) platform on Sandia’s Z-Machine due to the lack of Tritium being used. The recent development of ICF implosions with tritiated fuel will open the possibility of measuring the gamma reaction history on the Z-Machine. A forward model of the Gamma Reaction History diagnostic on Z (GRH-Z) has been developed using the MCNP6.3 (Monte-Carlo N-Particle) radiation transport code. The model included the Z-Machine geometry of interest to characterize the impact of neutron induced gamma rays on the DT reaction history measurements. In addition, the impulse response functions of the GRH-Z diagnostic to understand the temporal response of the detector, and the minimum yields required to make a reaction history measurement were calculated. This approach also predicted that with T 2 gas doping of MagLIF implosions a reaction history may be made for high performance shots >8e12-2.4e13 depending on the chosen threshold for the detector, with a maximum signal to background ratio of 25%. It was found that for long duration ICF implosions that additional collimation will be needed to prevent the neutron induced gamma rays from modifying the shape of the measured DT reaction history curve.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Perspectives and challenges of ultra-high temperature ceramics for fusion plasma-facing applications

Ultra-high temperature ceramics (UHTCs) offer several potential advantages as plasma-facing components (PFCs) in fusion reactors due to their extreme melting points, tailorable thermal conductivity, and attractive unirradiated mechanical properties including fracture toughness comparable or superior to tungsten. Here, recent developments and material properties of UHTCs are briefly reviewed, along with an overview of limited studies on their responses to neutron irradiation and an evaluation of plasma-surface interactions. Five key research pathways, primarily focused on irradiation effects, for advancing UHTCs in PFC applications are discussed: (1) assessing irradiation effects on the coupled thermal–mechanical performance (2) addressing the lack of studies on irradiation, plasma-surface interactions, and their synergistic effects; (3) investigating high-temperature (>1000 °C) neutron irradiation effects critical for PFC performance; (4) optimizing multi-component UHTC compositions or composites to improve thermal or mechanical properties; (5) enhancing radiation resistance to mitigate microcracking and void swelling through strategies such as increasing sink strength by reducing grain size, introducing fine particles, and leveraging complex concentrated alloy concepts.

36 MATERIALS SCIENCE↗

Neutronics and activation analysis of lithium-based ternary alloys in IFE blankets

Here we report that an attractive feature of using liquid lithium as the breeder and coolant in fusion blankets is that it has very high tritium solubility and results in very low levels of tritium permeation throughout the facility infrastructure. However, lithium metal vigorously reacts with air and water and presents plant safety concerns. The Lawrence Livermore National Laboratory is carrying an effort to develop a lithium-based alloy that maintains the beneficial properties of lithium (e.g. high tritium breeding and solubility) and at the same time reduces overall flammability concerns. This study evaluates the neutronics performance of lithium-based alloys in the blanket of an inertial fusion energy chamber in order to inform such development. 3-D Monte Carlo calculations were performed to evaluate two main neutronics performance parameters for the blanket: tritium breeding ratio (TBR), and the fusion energy multiplication factor (EMF). It was found that elements that exhibit low absorption cross sections and higher q-values such as lead, tin, and strontium, perform well with those that have high neutron multiplication such as lead and bismuth. These elements meet TBR constrains ranging from 1.02 to 1.1. However, most alloys do not reach EMFs greater than 1.15. Additionally, it was found that enriching lithium significantly increases the TBR and decreases the minimum lithium concentration by more than 60%. The amount of enrichment depends on how much total lithium is in the alloy to begin with. Alloys that performed well in the TBR and EMF calculations were considered for activation analysis. Activation simulations were executed with 50 years of irradiation and 300 years of cooling. It was discovered that bismuth is a poor choice due to achieving the highest decay heat, contact dose rates, and accident doses. In addition, it does not meet the waste disposal ratings (WDR). Some of the activation results for alloys with tin, zinc, and gallium were in the higher end and should be considered secondary to elements such as strontium and barium that had overall better results. The results of this study along with other considerations such as thermodynamics, and chemical reactivity will help down select a preferred lithium ternary alloy.

36 MATERIALS SCIENCE↗

Multimodal and multiscale strengthening mechanisms in Al-Ni-Zr-Ti-Mn alloy processed by laser powder bed fusion additive manufacturing

The unique thermokinetics of laser-powder bed fusion additive manufacturing (L-PBFAM) has been exploited for development of a novel high-strength Al-Ni-Ti-Zr-Mn alloy. The addition of 0.5 wt% Mn leads to extraordinary improvement in ultimate tensile strength (502 MPa) and work hardening due to the activation of two Mn-induced strengthening mechanisms. First, by a bimodal particle strengthening effect due to Al 31 Mn 6 Ni 12 nano-quasi-crystal particles rejected in inter-dendritic spaces and fibrous Al 3 Ni eutectic dendritic channels, which predominately contributes to the strength improvement, and second by solid solution strengthening from remaining Mn entrapped in Al. These mechanisms supplement the particle strengthening effect imparted by coherent and incoherent Al 3 (Ti,Zr) co-precipitates present at melt pool boundaries, dislocation strengthening due to solidification induced strain, and Hall-Petch and backstress strengthening effect due to heterogenous grain size distribution occurring at various length scales. In conclusion, the solidification dynamics and hierarchical heat distribution that are associated with L-PBFAM resulted in complex spatial variations in these strengthening phenomena and were investigated via a high-throughput multiscale structure–property correlation that involved thermokinetic simulation, X-ray diffraction, high-resolution nanoindentation mapping, and site-specific transmission electron microscopy of the alloy.

36 MATERIALS SCIENCE↗

Experimental validation of thermodynamic mixture rules at extreme pressures and densities

Accurate modeling of a mixed material Equation of State (EOS) at high pressures (~1 to 100 Mbar) is critical for simulating inertial confinement fusion and high energy density systems. Here, this paper presents a comparison of two mixing rule models to the experiment to assess their applicability in this regime. The shock velocities of polystyrene, aluminum, and nickel aluminide (NiAl) were measured at a shock pressure of ~3 TPa (~30 Mbar) on the Omega EP laser facility (Laboratory for Laser Energetics, University of Rochester, New York). The resultant shock velocities were compared to those derived from the RAGE (Eulerian) hydrodynamics code to validate various mixing rules used to construct an EOS for NiAl. The simulated shock transit time through the sample (Al or NiAl) matched the measurements to within the ±45ps measurement uncertainty. The law of partial volume (Amagat) and the law of partial pressure (Dalton) mixture rules provided equally good matches to the NiAl shock data. Other studies showed that the Amagat mixing rule is superior, and we recommend it since our results also show a satisfactory match. In conclusion, the comparable quality of the simulation to data for the Al and NiAl samples implies that a mixture rule can supply an EOS for plasma mixtures with adequate fidelity for simulations where mixing takes place, such as advective mix in an Eulerian code or when two materials are mixed together via diffusion, turbulence, or other physical processes.

36 MATERIALS SCIENCE↗

Dielectric properties of neutron and proton irradiated polymeric nanocomposite insulation for superconducting magnets of fusion power plants

Studies on radiation-resistant electrical insulation for superconducting magnets of nuclear fusion power plants are discussed. Metal oxide nanoparticle-incorporated organic polymer composite (MONAP) insulation films were manufactured and studied for their dielectric breakdown strength after exposure to neutrons and proton radiation at varying levels. Samples with up to 5 wt% of nanoparticles (NPs) of SiO 2 , MgO, and ZrO 2 were studied. The samples were exposed to radiation of up to 2 × 10 16 neutrons/cm 2 and 200 Mrad of protons. The addition of the nanoparticles improved the radiation resistance of the MONAP, and the performance depended on the type of NPs and the radiation exposure. Dielectric breakdown measurements at 77 K showed little degradation. Enhancement of dielectric strength was observed in some instances.

36 MATERIALS SCIENCE↗

Measurement of areal density in the ablators of inertial-confinement-fusion capsules via detection of ablator (n, n Prime {gamma}) gamma-ray emission

We report the first gamma-ray-based measurements of the areal density of ablators in inertial-confinement-fusion capsule implosions. The measurements, made at the OMEGA laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)], used observations of gamma rays arising from inelastic scattering of 14.1-MeV deuterium-tritium (DT) neutrons on {sup 12}C nuclei in the compressed plastic ablators. The emission of {sup 12}C(n,n Prime {gamma}) gamma rays from the capsules is detected using the Gamma Reaction History instrument [H. W. Herrmann et al., J. Phys.: Conf. Ser. 244, 032047 (2010)] operating at OMEGA. From the ratio of a capsule's {sup 12}C(n,n Prime {gamma}) emission to the emission from the same processes in an in situ reference graphite 'puck' of known mass and geometry [N. M. Hoffman et al., in IFSA 2011 proceedings (submitted)], we determine the time-averaged areal density of {sup 12}C in the capsule's compressed ablator. Measured values of total ablator areal density for thirteen imploded capsules, in the range 23 {+-} 10 to 58 {+-} 14 mg/cm{sup 2}, are comparable to values calculated in 1D radiation-hydrodynamic simulations, and measured by charged-particle techniques.

36 MATERIALS SCIENCE↗

Low Conductivity SiC/SiC Ceramic Composites for Fusion Blanket Flow Channel Inserts

Dual-coolant blanket designs for fusion reactors currently under development benefit from flow channel inserts that possess low electrical conductivity and low thermal conductivity. Such flow channel inserts will advance the state of fusion technology closer to producing continuous low cost, non-polluting power as is planned under DEMO. In addition to low electrical and thermal conductivity, the desired properties of the flow channel insert are compatibility with lead-lithium breeder/coolant, stability under a high neutron fluence, and mechanical robustness. Silicon carbide fiber-reinforced silicon carbide matrix composites (SiC/SiC) have been shown to meet all of these requirements with the exception of the thermal conductivity requirement. Efforts to manipulate the thermal conductivity included compositional and architectural approaches. An architecturally engineered SiC/SiC was demonstrated that met the low through-thickness thermal conductivity. An understanding of the factors controlling the through-thickness electrical conductivity was also developed and now allows engineering control of the electrical conductivity within the composite. Refinements in the design of a SiC/SiC composite flow channel insert were performed as well as identifying critical mechanical properties. Testing in molten Pb-Li was performed in a building-block manner starting with coupons and culminating in the testing of SiC/SiC flow channel insert segments at ~500ºC under 10 psig. Sections of both a simpler monocoque SiC/SiC flow channel insert and a nested flow channel insert were evaluated for compatibility and impermeability in the Pb-Li and included in situ measurements of electrical and thermal conductivity.

36 MATERIALS SCIENCE↗

Neutron and photon in-vivo materials characterization at the evolving plasma-material interface in plasma-burning fusion environments

This report includes the first set of MOSS data collected in the context of fusion-relevant plasma-material interactions. The data collected show that the surface curvature and stress irreversibly change during low-energy deuterium ion irradiation. This holds for both tungsten thin films, bulk tungsten, and single-crystal silicon. Meanwhile, argon irradiation did not produce this same effect. The surface morphology of the exposed samples was virtually identical regardless of gas species. There were, however, some surface chemistry differences between argon-exposed and deuterium-exposed samples, mainly concerning the oxide states of the W4f XPS signal. The changes in surface chemistry could be due to hydrogen dynamics on the tungsten surfaces, though further investigation will be required with in-situ irradiation and analysis. The changes in surface stress could also not be explained by temperature alone, as the temperature reached during the ion irradiations was too low to induce non-elastic strain. With this in mind, deuterium retention in the materials could change the surface curvature and stress. To confirm this, further work will be needed to quantify the change in curvature and relate it to ion flux, fluence, and deuterium retention. Unfortunately, when this work was conducted, the experimental setup for thermal desorption spectroscopy was not operating correctly, and that work could not be included in this dissertation. Despite experimental difficulties, this work shows the first results of a promising technique to study deuterium dynamics in tungsten-based reconstituted thin films.

36 MATERIALS SCIENCE↗