SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
C is Theoretical Carbon Structure structured and crystallizes in the tetragonal I4/mmm space group. The structure is three-dimensional. C is bonded to four equivalent C atoms to form a mixture of edge and corner-sharing CC4 tetrahedra. There is two shorter (1.53 Å) and two longer (1.58 Å) C–C bond length.
Lithium–sulfur (Li–S) batteries are considered one of the most promising next-generation energy storage technologies for electric vehicles, owing to their high energy density (up to three times greater than current lithium-ion batteries) and the low cost of sulfur (approximately 100 times cheaper than conventional cobalt oxide). However, several challenges hinder their commercial viability, including the electronically and ionically insulating nature of sulfur, polysulfide dissolution, and lithium dendrite growth. These issues significantly limit battery energy density and cycle life and must be addressed to enable successful commercialization. Current strategies involving porous carbon structures, additives, and electrocatalyst engineering have not fully resolved the polysulfide dissolution problem. While polysulfide-free cathode materials offer a promising solution, they often suffer from low sulfur content, leading to reduced discharge capacity and sluggish reaction kinetics. To overcome these limitations, we have developed novel soluble-polysulfide-free sulfur cathode active materials with a high sulfur content (>50 wt%). By integrating these cathodes with functional binders, optimized electrolyte formulations, and refined electrode fabrication techniques, we demonstrate Li–S batteries with both high energy density and long cycle life. This advancement brings the realization of low-cost, high-energy Li–S batteries significantly closer to practical application.
Per- and polyfluoroalkyl substances (PFAS) have been a rising concern for the past two decades, with the United States Department of Defense and Environmental Protection Agency investing millions of dollars in research into remediation and clean-up technologies. Due to the environmental persistence, toxicity, biological uptake, and ongoing changes in both federal and state regulatory space, understanding the fate and transport of PFAS compounds has been of growing concern to the US Department of Energy (DOE). The DOE’s Hanford Site is investigating historical use of PFAS and will be doing site characterization for PFAS. Thus, PFAS have not yet been identified as a contaminant concern in regulatory documents. Based on historical records that mention the discharge of aqueous film-forming foam containing PFAS and having on-site fire stations (a risk factor for PFAS contamination), it seems likely that environmental releases of PFAS may have occurred. Pump and treat (P&T) remediation is the selected remedy for multiple groundwater contaminant plumes at Hanford. These P&T systems use ion exchange (IX) as a component of aboveground treatment, with the specific resins depending on the target contaminants. There is potential that these IX resins may be able to remove PFAS from groundwater, but investigation is needed to understand affinity/selectivity and removal capacity given the groundwater composition and the operating conditions. This report provides background on PFAS uses and chemistry, then provides a review of IX resin applications for PFAS, identifying knowledge gaps. Recommendations are provided regarding research needed to address knowledge gaps and acquire information needed to propose IX as a future PFAS remediation technology at the Hanford Site, as well as other U.S. Department of Energy sites. Generally, PFAS compounds are fluorinated substances that contain at least one fully fluorinated methyl or methylene carbon – with a few noted exceptions, any chemical with at least a perfluorinated methyl group (–CF3) or a perfluorinated methylene group (–CF2–) is a PFAS. These chemical compounds are characterized as non-biodegradable, non-reactive, non-photolytic, and hydrolysis resistant. This makes them highly recalcitrant within the environment, however polyfluoroalkyl materials are less recalcitrant as the carbon chains contain C–H bonds which are more easily broken than carbon – fluorine (C–F) bonds. The backbone carbon structures are commonly punctuated with a head group, the most well-known of them are perfluorooctanesulfonic acid and perfluorooctanoic acid, which possess a sulfonate and a carboxylate group, respectively. IX resins are marketed for the removal of PFAS from water systems and industrial water, however, the mechanism of removal is not as well understood as for anion or cation removal. A better understanding of the mechanism of removal would enable the development of IX resins that have improved specificity for PFAS removal. Four knowledge gaps were identified: 1) the effect of dissolved ions on the IX resin PFAS removal effectiveness, 2) the effect of additional primary contaminants of concern (PCOCs) or secondary contaminants of concern (SCOCs) on the effectiveness of PFAS via IX resin, 3) the mechanisms of PFAS removal from water, and 4) practical solutions to IX resin regeneration and waste disposal.
Coal has been challenged because coal combustion generates large quantities of carbon dioxide (CO2), which contributes to global warming. Pyrolysis char (PC), a valuable byproduct of coal that does not liberate CO2 when produced in an inert environment, can be used as a high carbon content fuel in combustion and gasification. However, using PC as a fuel is not an eco-friendly and cost-efficient way to make energy. Contrastingly using PC to make engineered products does offer an eco-friendly, attractive and value-added use. This paper introduces a novel integrated coal pyrolysis and solvent extraction process invented by the University of Wyoming (UW) to convert as-mined coal from the Powder River Basin Coal Field, Wyoming, to functional carbon products, which together liberates very little CO2. PC and coal deposit, extract and residual (CDER) are two functional carbon products that can be used in the development and manufacture of high value coal-derived building materials. The novel development of three building products known as coal-derived char bricks (CCB), carbon structural unit (CSU), and char-based insulation foam (CIF) are introduced. The approaches to manufacture them are investigated, including consideration of the eco-friendly approaches, optimization of engineering performance, and cost effectiveness relative to traditional products. CCBs show advantages in terms of their light weight (< 1 g/cm3) and good compressive strength (> 14 MPa). CSUs possess high compressive strength (> 30 MPa) and low thermal conductivity (< 0.3 W/mK), while CIFs can achieve a low thermal conductivity of 0.06 W/mK. Two demonstration houses have been built on UW campus, one using CCBs and another using commercial clay bricks. The performances of these houses are being monitored for temperature control, humidity uptake, noise reduction, inside air volatile organic content, indoor air quality and weatherability. The performance of the CCBs in terms of these criteria is discussed.
Blending polyacrylonitrile (PAN) with plastic wastes and bio-based polymers provides a convenient and inexpensive method to realize cost-effective carbon fiber (CF) precursors. In this work, PAN-based blend precursors are investigated using ReaxFF reactive molecular dynamics simulations with respect to the formation of all-carbon rings, the evolutions of oxygen-containing and nitrogen-containing species, and the migration of carbon atoms to form turbostratic graphene. From these simulations, we identify that PAN/cellulose (CL) blend manifests the highest carbon yield and the most substantial all-carbon ring formation. This ReaxFF-based finding is confirmed by Raman and TEM experiments indicating high crystallinity for PAN/CL-derived blend CFs. We trace the pathway of gasification and carbonization of PAN/CL to elaborate the mechanism of the formation of all-carbon ring networks. We discover that the acetals of CL can catalyze the cyclization of the blend precursor, allowing for the search for CL derivatives or the other kinds of bio-based polymers with similar functionalities as alternative blends. In addition, we examine the structural characteristics using the carbon–carbon (C–C) radial distribution functions, C–C bond length distributions, and sp2 C atom ratios for the four representative precursors, i.e., PAN, oxidized PAN, PAN/nylon 6,6, and PAN/CL. Our simulation results show the most extensive all-carbon ring cluster and graphitic structure growths for PAN/CL. Here, we propose PAN/CL as a cost-effective alternative CF precursor, since (a) CL is naturally abundant and eco-friendly for production, (b) the blend precursor PAN/CL does not require oxidation treatment, (c) PAN/CL has a high carbon yield with substantial all-carbon ring formation, and (d) PAN/CL based CFs potentially provide a mechanical property enhancement.
Carbonic anhydrase (CA) is an attractive biodegradable catalyst for CO 2 absorption in solvent–based CO 2 capture. However, maintaining the stability of CA as a homogeneous component of the solvents is a challenge. Solvent regeneration temperature typically exceeds the enzyme thermal tolerance, which leads to CA deactivation. To reduce the need for frequent CA replenishment and to avoid inactive CA accumulation in the solvent, this work shows the benefits of an immobilization strategy where CA is fixed in a second–generation design of textile structured packing (CATSP–2) modules. The enzyme–immobilized packing showed 1.5 times better performance in CO 2 separation compared with traditional structured packing with a corresponding increased CO 2 loading in the rich solvent. The modules exhibited good CA activity retention of ~80% during the tests without any CA replenishment. As a result, applying CATSP–2 could potentially decrease the packing height and absorber column size for a lower cost per amount of CO 2 captured.
A hydrogen peroxide initiated sol-gel process involving molybdenum transformation in the presence of dopamine (Dopa) hydrochloride excess produced the metastable precipitate composed of polydopamine (PDopa) spheres coated with Dopa preintercalated molybdenum oxide, (Dopa) x MoO y @PDopa. The hydrothermal treatment (HT) of the (Dopa) x MoO y @PDopa precursor resulted in the simultaneous carbonization of Dopa and molybdenum reduction generating MoO 2 nanoplatelets distributed and confined on the surface of the Dopa-derived carbon matrix (HT-MoO 2 /C). The consecutive annealing (An) of the HT-MoO 2 /C sample at 600 °C under Ar atmosphere led to the formation of MoO 2 with increased Mo oxidation state and improved structural stability (AnHT-MoO 2 /C). Annealing had also further facilitated interaction between the molybdenum-derived and Dopa-derived components resulting in the modification of the carbon matrix confirmed by Raman spectroscopy. Morphology of both materials is best described as Dopa-derived carbon spheres decorated with MoO 2 nanoplatelets. These integrated metal oxide and carbon structures were tested as electrodes for lithium-ion batteries in the potential window that corresponds to the intercalation mechanism of charge storage. The AnHT-MoO 2 /C electrode showed enhanced electrochemical activity, with an initial specific discharge capacity of 260 mAh/g and capacity retention of 67% after 50 cycles, compared to the HT-MoO 2 /C electrode which exhibited an initial specific discharge capacity of 235 mAh g –1 and capacity retention of 47% after 50 cycles. The rate capability experiments revealed that the capacity of 93 mAh/g and 120 mAh/g was delivered by the HT-MoO 2 /C and AnHT-MoO 2 /C electrodes, respectively, when the current density was increased to 100 mA/g. Here, the improved specific capacity, electrochemical stability, and rate capability achieved after annealing were attributed to higher crystallinity of MoO 2 , increased oxidation state of Mo, and formation of the tighter MoO 2 /carbon contact accompanied by the annealing assisted interaction between MoO 2 and Dopa-derived carbon.
Improved understanding of structural and chemical properties through local experimental probes, such as X-ray absorption near-edge structure (XANES) spectroscopy, is crucial for the understanding and design of functional materials. In recent years, significant advancements have been made in the development of data science approaches for the automated interpretation of XANES structure–spectrum relationships. However, existing studies have primarily focused on crystalline solids and small molecules, while fewer efforts have been devoted to disordered systems. Thus, in this work, we demonstrate the development of neural network models for predicting and interpreting XANES spectra of amorphous carbon (a-C) from local structural descriptors. Comparison between different structural descriptors expectedly shows that the inclusion of both bond length and bond angle information is necessary for an accurate prediction of the spectra. Among the descriptors considered in this work, we find that the local many-body tensor representation yields the highest accuracy and greatest interpretability so that it can be leveraged to understand the importance of structural motifs in determining XANES spectra. Furthermore, we also discuss performance of neural network models for predicting both local structure features, such as bond lengths and bond angles, and global chemical composition, such as the sp:sp 2 :sp 3 ratio.
Ocean acidification heavily impacts marine ecosystems by reducing calcification. Many coral-algae symbiotic relationships are in jeopardy due to the destruction of coral reefs. Here, a ceramic ink compatible with the direct ink write additive manufacturing technique was formulated and used to print marine compatible structures that could grow algae and restore that relationship. A diacrylate polymer was mixed with calcium carbonate, a material that comprises a coral skeleton, to create a slurry with shear thinning properties. Rheology studies were conducted to confirm printing properties and characterize the slurry. Printed parts demonstrated strong control over print features, including size and infill design. Various infill patterns and percentages were attempted to optimize printability and potential algae growth. Thermogravimetric analysis helped determine a logical burnout and sintering procedure to avoid large cracking. This project developed a printable and sinter-able calcium carbonate ceramic slurry for complex marine-compatible structures and algae growth. This research was conducted in the support of the Eco Reef project.
Understanding of recently reported putative close-to-room-temperature superconductivity in C-S-H compounds at 267 GPa demands a reproducible synthesis protocol as well as knowledge of the compounds' structure and composition. Here, we synthesized C-S-H compounds with various carbon compositions at high pressures from elemental carbon C and methane CH 4 , sulfur S, and molecular hydrogen H 2 . Here, we focus on compounds synthesized using methane as these allow a straightforward determination of their structure and composition by combining single-crystal x-ray diffraction and Raman spectroscopy. We applied a two-stage synthesis of [(CH 4 ) x (H 2 S) (1-x) ] 2 H 2 compounds with various compositions by first reacting sulfur and mixed methane-hydrogen fluids and forming CH 4 -doped H 2 S crystals at 0.5-3 GPa and then by growing single crystals of the desired hydrogen-rich compound. Raman spectroscopy applied to this material shows the presence of CH 4 molecules incorporated into the lattice and allows the determination of the CH 4 content, while single-crystal x-ray diffraction results suggest that the methane molecules substitute H 2 S molecules. The structural behavior of these compounds is very similar to the previously investigated methane-free crystals demonstrating a transition from Al 2 Cu type I4/mcm molecular crystal to a modulated molecular structure at 20-30 GPa and back to the same basic I4/mcm structure in an extended modification with greatly modified Raman spectra. This latter phase demonstrates a distortion into a Pnma structure at 132-159 GPa and then transforms into a common Im$\bar{3}$m H 3 S phase at higher pressures; however, no structural anomaly is detected near 220 GPa, where a sharp upturn in T c has been reported.
A method of synthesizing an electrode material for lithium ion batteries from Fe 3 O 4 nanoparticles and multiwalled carbon nanotubes (MWNTs) to yield (Fe 3 O 4 -NWNTs) composite heterostructures. The method includes linking the Fe 3 O 4 nanoparticles and multiwalled carbon nanotubes using a π-π interaction synthesis process to yield the composite heterostructure electrode material. Since Fe 3 O 4 has an intermediate voltage, it can be considered an anode (when paired with a higher voltage material) or a cathode (when paired with a lower voltage material).
A method of fabricating nanocomposite anode material embodying a lithium titanate (LTO)-multi-walled carbon nanotube (MWNT) composite intended for use in a lithium-ion battery includes providing multi-walled carbon nanotube (MWNTs), including nanotube surfaces, onto which functional oxygenated carboxylic acid moieties are arranged, generating 3D flower-like, lithium titanate (LTO) microspheres, including thin nanosheets and anchoring the acid-functionalized MWNTs onto surfaces of the 3D LTO microspheres by π-π interaction strategy to realize the nanocomposite anode material.
A method of fabricating nanocomposite anode material embodying a lithium titanate (LTO)-multi-walled carbon nanotube (MWNT) composite intended for use in a lithium-ion battery includes providing multi-walled carbon nanotube (MWNTs), including nanotube surfaces, onto which functional oxygenated carboxylic acid moieties are arranged, generating 3D flower-like, lithium titanate (LTO) microspheres, including thin nanosheets and anchoring the acid-functionalized MWNTs onto surfaces of the 3D LTO microspheres by π-π interaction strategy to realize the nanocomposite anode material.
Carbon molecular sieve (CMS) membranes offer the best available combination of scalable economical processability with excellent separation performance. Physical aging of CMS membranes causes pore structure changes over time that affect CMS membrane performance. To provide fundamental insights into the structure evolution in CMS membranes during physical aging, a combined dual-mode sorption and transport model is used in this study to characterize the diffusion coefficients of gas molecules in fresh and 7-day vacuum aged CMS membranes. Further, the results show physical aging of CMS membrane is primarily “diffusion related” and such aging behavior simultaneously causes ultramicropore changes in the continuous phase and Langmuir phase of CMS membrane. The new insights offered in this study suggest strategies to control the physical aging of CMS membranes and even use it as a valuable tool to tune the separation performance of CMS membranes for demanding gas separations.
Abstract Carbon molecular sieve (CMS) membranes offer the best available combination of scalable economical processability with excellent separation performance. Physical aging of CMS membranes causes pore structure changes over time that affect CMS membrane performance. To provide fundamental insights into the structure evolution in CMS membranes during physical aging, a combined dual‐mode sorption and transport model is used in this study to characterize the diffusion coefficients of gas molecules in fresh and 7‐day vacuum aged CMS membranes. The results show physical aging of CMS membrane is primarily “diffusion related” and such aging behavior simultaneously causes ultramicropore changes in the continuous phase and Langmuir phase of CMS membrane. The new insights offered in this study suggest strategies to control the physical aging of CMS membranes and even use it as a valuable tool to tune the separation performance of CMS membranes for demanding gas separations.
Amorphous calcium carbonate (ACC) is a precursor of crystalline calcium carbonate; hence, its structural information at the atomic level is very important for controlling the morphology of crystalline calcium carbonate. In this study, we attempted to elucidate the process of Sr extraction from aqueous solution by using ACC for the purpose of removal of radioactive Sr from the contaminated water leaked after the Fukushima Daiichi nuclear accident. Here, the pair distribution functions, g(r) obtained by X-ray and neutron diffraction (ND) measurements show that ACC has a structure partially similar to that of monohydrocalcite, suggesting that ACC is transferred to the crystalline calcium carbonate starting from its crystal nucleus. Rietveld analysis of the ND data showed that the ACC that removed Sr was crystallized to calcite. However, the Sr–O coordination analyzed using extended X-ray absorption fine structure (EXAFS) implies that the local environment of O around Sr is similar to that in crystalline calcium carbonate aragonite.
High-performance carbon dioxide (CO 2 )-capture technologies with low environmental impact are necessary to combat the current climate change crisis. Durable and versatile “drop-in-ready” textile structured packings with covalently immobilized carbonic anhydrase (CA) were created as efficient, easy to handle catalysts for CO 2 absorption in benign solvents. The hydrophilic textile structure itself contributed high surface area and superior liquid transport properties to promote gas-liquid reactions that were further enhanced by the presence of CA, leading to excellent CO 2 absorption efficiencies in lab-scale tests. Mechanistic investigations revealed that CO 2 capture efficiency depended primarily on immobilized enzymes at or near the surface, whereas polymer entrapped enzymes were more protected from external stressors than those exposed at the surface, providing strategies to optimize performance and durability. Textile packing with covalently attached enzyme aggregates retained 100% of the initial 66.7% CO 2 capture efficiency over 71-day longevity testing and retained 85% of the initial capture efficiency after 1-year of ambient dry storage. Subsequent stable performance in a 500 h continuous liquid flow scrubber test emphasized the material robustness. Biocatalytic textile packings performed well with different desirable solvents and across wide CO 2 concentration ranges that are critical for CO 2 capture from coal and natural gas-fired power plants, from natural gas and biogas for fuel upgrading, and directly from air.
The effect of the core–skin structure on the mechanical properties of carbon nanofibers is investigated in large-scale molecular dynamics simulations of tensile deformation of carbon nanofibers with the core–skin and homogeneous structures. Contrary to an established notion of the deleterious effect of the skin layer on the strength of carbon fibers, the presence of a high-quality skin layer is found to increase both the Young’s modulus and tensile strength of the nanofiber. A detailed analysis of the fracture process indicates that the nanofiber strengthening is related to the ability of skin layer to suppress crack nucleation at the core–skin interface. Furthermore, the computational predictions suggest that the design of new approaches to carbon fiber manufacturing and processing leading to the generation of a high-quality skin layer while avoiding the introduction of structural defects at the core–skin interface may yield a significant enhancement of the mechanical properties of carbon fibers.