Search NASA⌕ Search

SEARCH · Search NASA

Results for “Control equipment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

A visual motion simulator for general aviation compensated within the nonlinear adaptive washout for actuator lag

A description is presented of the general aviation aircraft simulator recently acquired by the Langley Research Center, summarizing the complement of instruments, radio/navigation equipment, control loading, and other features. Emphasis is placed mainly on the two-degree-of-freedom motion drives developed for this simulator and the presentation of the dynamic response of the motion system (without washout) in terms of amplitude ratio and phase lag as a function of frequency. The nonlinear adaptive washout based on continuous steepest descent optimization presents cues in pitch rate, surge, roll rate, and sway, and allows for actuator lag compensation.

Ashworth, B. R.↗
NASA NTRS1979

Improved notation controller

Nutation controller equipped with angular accelerometer stabilizes spinning bodies without precise positioning or calibration.

Donohue, J.↗
NASA NTRS1978

Flight demonstrations of curved, descending approaches and automatic landings using time referenced scanning beam guidance

The Terminal Configured Vehicle (TCV) program operates a Boeing 737 modified to include a second cockpit and a large amount of experimental navigation, guidance and control equipment for research on advanced avionics systems. Demonstration flights to include curved approaches and automatic landings were tracked by a phototheodolite system. For 50 approaches during the demonstration flights, the following results were obtained: the navigation system, using TRSB guidance, delivered the aircraft onto the 3 nautical mile final approach leg with an average overshoot of 25 feet past centerline, subjet to a 2-sigma dispersion of 90 feet. Lateral tracking data showed a mean error of 4.6 feet left of centerline at the category 1 decision height (200 feet) and 2.7 feet left of centerline at the category 2 decision height (100 feet). These values were subject to a sigma dispersion of about 10 feet. Finally, the glidepath tracking errors were 2.5 feet and 3.0 feet high at the category 1 and 2 decision heights, respectively, with a 2 sigma value of 6 feet.

White, W. F.↗
NASA NTRS1977

Stationary diesel engines for use with generators to supply electric power

The procurement of stationary diesel engines for on-site generation of electric power deals with technical criteria and policy relating to federal agency, not electrical components of diesel-generator sets or for the design of electric-power generating plants or their air-pollution or noise control equipment.

Source record↗
NASA NTRS1978

Summary of system state-of-health measurements STRATCOM 8: A balloon experiment

Various measurements were made to determine the temperature and attitude of the gondola and the status of primary power and control equipment. Bead thermistors were used to measure temperatures at selected points throughout the gondola. A two-axis magnetometer and a two-axis pendulum were used to measure gondola attitude. Voltage and current measurements indicated the status of the primary power sources and associated power converters.

Herrington, P. B.↗
NASA NTRS1979

Electromechanical flight control actuator

The feasibility of using an electromechanical actuator (EMA) as the primary flight control equipment in aerospace flight is examined. The EMA motor design is presented utilizing improved permanent magnet materials. The necessary equipment to complete a single channel EMA using the single channel power electronics breadboard is reported. The design and development of an improved rotor position sensor/tachometer is investigated.

Source record↗
NASA NTRS1982

Ultrasonic Transducer Analyzer

Ultrasonic transducer-beam-intensity distributions are determined by analyzing echoes from a spherical ball. Computers control equipment and process data. Important beam characteristics, such as location of best beam focus and beam diameter at focus, can be determined quickly from extensive set of plots generated by apparatus.

Grounds, M. K.↗
NASA NTRS1980

Monitoring and control requirement definition study for Dispersed Storage and Generation (DSG). Volume 4, appendix C: Identification from utility visits of present and future approaches to integration of DSG into distribution networks

Visits to four utilities concerned with the use of DSG power sources on their distribution networks yielded useful impressions of present and future approaches to the integration of DSGs into electrical distribution network. Different approaches to future utility systems with DSG are beginning to take shape. The new DSG sources will be in decentralized locations with some measure of centralized control. The utilities have yet to establish firmly the communication and control means or their organization. For the present, the means for integrating the DSGs and their associated monitoring and control equipment into a unified system have not been decided.

Source record↗
NASA NTRS1981

Large area sheet task. Advanced dendritic web growth development

The development of a silicon dendritic web growth machine is discussed. Several refinements to the sensing and control equipment for melt replenishment during web growth are described and several areas for cost reduction in the components of the prototype automated web growth furnace are identified. A circuit designed to eliminate the sensitivity of the detector signal to the intensity of the reflected laser beam used to measure melt level is also described. A variable speed motor for the silicon feeder is discussed which allows pellet feeding to be accomplished at a rate programmed to match exactly the silicon removed by web growth.

Duncan, C. S.↗
NASA NTRS1981

Low cost, high concentration ratio solar cell array for space applications

A miniaturized Cassegrainian-type concentrator solar array concept for space applications is described. In-orbit cell operating temperatures near 80 C are achieved with purely passive cell cooling and a net concentration ratio of 100. A multiplicity of miniaturized, rigid solar cell concentrator subassemblies are electrically interconnected in conventional fashion and mounted into rigid frames to form concentrator solar panel assemblies approximately 14-mm thick. A plurality of such interconnected panels forms a stowable and deployable solar cell blanket. It is projected that for 20% efficient silicon cells an array of 500 kW beginning-of-life output capability, including orbiter cradle structures, can be transported by a single shuttle orbiter flight into low earth orbit. In-orbit array specific performance is calculated to be approximately 100 W/sq m and 20 W/kg, including all stowage, deployment and array figure control equipment designed for a 30-year orbital life. Higher efficiency gallium arsenide and multiple band gap solar cells will improve these performance factors correspondingly.

Patterson, R. E.↗
NASA NTRS1982

Lightning protection of wind turbines

Possible damages to wind turbine components due to lightning strikes are discussed and means to prevent the damage are presented. A low resistance path to the ground is noted to be essential for any turbine system, including metal paths on nonmetal blades to conduct the strike. Surge arrestors are necessary to protect against overvoltages both from utility lines in normal operation and against lightning damage to control equipment and contactors in the generator. MOS structures are susceptible to static discharge injury, as are other semiconductor devices, and must be protected by the presence of static protection circuitry. It is recommended that the electronics be analyzed for the circuit transient response to a lightning waveform, to induced and dc current injection, that input/output leads be shielded, everything be grounded, and lightning-resistant components be chosen early in the design phase.

Dodd, C. W.↗
NASA NTRS1984

Cockpit resource management training

Cockpit resource management which is a multifaceted concept is outlined. The system involves the effective coordination of many resources: aircraft systems, company, air traffic control, equipment, navigational aids, documents, and manuals. The main concept, however, is group interaction. Problems which arise from lack of coordination, decision making, and lack of communication are pointed out. Implementation by the regional airline industry of cockpit resource management, designed to deal with human interactions problems in the most cost effective manner, is discussed.

Yocum, M.↗
NASA NTRS1988

Mobilestar field test program

Various field tests were performed in order to gain practical experience and a broader understanding of mobile communications. The first phase consisted of CW propagation tests to develop firsthand experience of propagation phenomena. From this information, estimates of the feasibility and accuracy of power control were possible. The next phase tested the idea of power control. Equipment representative of that expected to be used in an actual mobile satellite communication system was assembled and tested under a variety of environments.

Rubow, Wayne↗
NASA NTRS1988

An approach to CMG steering using feedback linearization

This paper presents an approach for controlling spacecraft equipped with control moment gyroscopes. A technique from feedback linearization theory is used to transform the original nonlinear problem to an equivalent linear form without approximating assumptions. In this form, the spacecraft dynamics appear linearly, and are decoupled from redundancy in the system of gyroscopes. A general approach to distributing control effort among the available actuators is described which includes provisions for redistribution of rotors, explicit bounds in gimbal rates, and guaranteed operation at or near singular configurations. A particular algorithm is developed for systems of double-gimbal devices, and demonstrated in two examples for which existing approaches fail to give adequate performance.

Dzielski, John↗
NASA NTRS1988

Environmental calibration chamber operations

Thermal vacuum capabilities are provided for the development, calibration, and functional operation checks of flight sensors, sources, and laboratory and field instruments. Two systems are available. The first is a 46 cm diameter diffusion pumped vacuum chambler of the bell jar variety. It has an internal thermal shroud, LN2 old trap, two viewing ports, and various electrical and fluid feedthroughs. The other, also an oil diffusion pumped system, consists of a 1.8 m diameter by 2.5 m long stainless steel vacuum tank, associated pumping and control equipment, a liquid nitrogen storage and transfer system and internal IR/visible calibration sources. This is a two story system with the chamber located on one floor and the pumping/cryogenic systems located on the floor below.

Lester, D. L.↗
NASA NTRS1990

Checking Automated-Welder Programs By Computer

Computer system detects and displays actual and potential errors in programs for computer-controlled electron-beam welder. Uses personal computer, separate from welding computer. Programmed specifically to highlight errors in welding program. Eliminates need for preweld full-power test run reducing checkout time to about half hour. Assures much higher quality, damage-free welding. Used to create and edit new programs for welder. Control computer thereby free for production. Useful for checking programs for such other computer-controlled equipment as inertia welders, robots, machine tools, and heat treaters.

Damicone, L. O.↗
NASA NTRS1991

Infrastructure for deployment of power systems

A preliminary effort in characterizing the types of stationary lunar power systems which may be considered for emplacement on the lunar surface from the proposed initial 100-kW unit in 2003 to later units ranging in power from 25 to 825 kW is presented. Associated with these power systems are their related infrastructure hardware including: (1) electrical cable, wiring, switchgear, and converters; (2) deployable radiator panels; (3) deployable photovoltaic (PV) panels; (4) heat transfer fluid piping and connection joints; (5) power system instrumentation and control equipment; and (6) interface hardware between lunar surface construction/maintenance equipment and power system. This report: (1) presents estimates of the mass and volumes associated with these power systems and their related infrastructure hardware; (2) provides task breakdown description for emplacing this equipment; (3) gives estimated heat, forces, torques, and alignment tolerances for equipment assembly; and (4) provides other important equipment/machinery requirements where applicable. Packaging options for this equipment will be discussed along with necessary site preparation requirements. Design and analysis issues associated with the final emplacement of this power system hardware are also described.

Sprouse, Kenneth M.↗
NASA NTRS1991

Approach to control moment gyroscope steering using feedback linearization

This paper presents an approach for controlling spacecraft equipped with control moment gyroscopes. A technique from feedback linearization theory is used to transform the original nonlinear problem to an equivalent linear form without approximating assumptions. In this form, the spacecraft dynamics appear linearly, and are decoupled from redundancy in the system of gyroscopes. A general approach to distributing control effort among the available actuators is described which includes provisions for redistribution of rotors, explicit bounds in gimbal rates, and guaranteed operation at or near singular configurations. A particular algorithm is developed for systems of double-gimbal devices, and demonstrated in two examples for which existing approaches fail to give adequate performance.

Dzielski, John↗