Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite/Epoxy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Dynamic responses of graphite/epoxy laminated beam to impact of elastic spheres

Wave propagation in 90/45/90/-45/902s and 0/45/0/-45/02s laminates of a graphite/epoxy composite due to impact of a steel ball was investigated experimentally and also by using a high order beam finite element. Dynamic strain responses at several locations were obtained using strain gages. The finite element program which incorporated statically determined contact laws was employed to calculate the contact force history as well as the target beam dynamic deformation. The comparison of the finite element solutions with the experimental data indicated that the static contact laws for loading and unloading (developed under this grant) are adequate for the dynamic impact analysis. It was found that for the 0/45/0/-45/02s laminate which has a much larger longitudinal bending rigidity, the use of beam finite elements is not suitable and plate finite element should be used instead.

Sun, C. T.↗
NASA NTRS1982

Stiffness reductions during tensile fatigue testing of graphite/epoxy angle-ply laminates

Tensile fatigue data was generated under carefully controlled test conditions. A computerized data acquisition system was used to permit the measurement of dynamic modulus without interrupting the fatigue cycling. Two different 8-ply laminate configurations, viz, + or - 45 (2s) and + or - 67.5 (2s), of a T300/5208 graphite/epoxy composite were tested. The + or - 45 (2s) laminate did exhibit some modulus decay, although there was no well-defined correlation with applied stress level or number of cycles. The + or - 67.5 (2s) laminate did not exhibit any measurable modulus decay. Secondary effects observed included a small but distinct difference between modulus as measured statically and dynamically, a slight recovery of the modulus decay after a test interruption, and a significant viscoelastic (creep) response of the + or - 45 (2s) laminate during fatigue testing.

Odom, E. M.↗
NASA NTRS1983

Characterization of delamination and transverse cracking in graphite/epoxy laminates by acoustic emission

Efforts to characterize and differentiate between two major failure processes in graphite/epoxy composites - transverse cracking and Mode I delamination are described. Representative laminates were tested in uniaxial tension and flexure. The failure processes were monitored and identified by acoustic emission (AE). The effect of moisture on AE was also investigated. Each damage process was found to have a distinctive AE output that is significantly affected by moisture conditions. It is concluded that AE can serve as a useful tool for detecting and identifying failure modes in composite structures in laboratory and in service environments.

Garg, A.↗
NASA NTRS1982

Fatigue of graphite/epoxy /0/90/45/-45/s laminates under dual stress levels

A model for the prediction of loading sequence effects on the statistical distribution of fatigue life and residual strength in composite materials is generalized and applied to (0/90/45/-45)s graphite/epoxy laminates. Load sequence effects are found to be caused by both the difference in residual strength when failure occurs (boundary effect) and the effect of previously applied loads (memory effect). The model allows the isolation of these two effects, and the estimation of memory effect magnitudes under dual fatigue loading levels. It is shown that the material memory effect is insignificant, and that correlations between predictions of the number of early failures agree with the verification tests, as do predictions of fatigue life and residual strength degradation under dual stress levels.

Yang, J. N.↗
NASA NTRS1981

The influence of environmental effects on the mechanical properties of graphite/epoxy laminates

The time dependent deformational and creep rupture processes in graphite/epoxy laminates are examined as a function of temperature and stress level. The role of accelerated characterization of design materials is discussed, and the use of a nonlinear time-temperature-stress-superposition principle in the determination of compliance master curves as a function of stress and temperature is considered. Creep rupture analytical models are discussed as applied to polymer-matrix composites, and the data is shown to be in general agreement with a logarithmic stress and temperature-dependent delayed fracture model. Comparisons between creep and rupture experiments and phenomenological models are presented.

Brinson, H. F.↗
NASA NTRS1982

Influence of quality control variables on failure of graphite/epoxy under extreme moisture conditions

Tension tests on graphite/epoxy composites were performed to determine the influence of various quality control variables on failure strength as a function of moisture and moderate temperatures. The extremely high and low moisture contents investigated were found to have less effect upon properties than did temperature or the quality control variables of specimen flaws and prepreg batch to batch variations. In particular, specimen flaws were found to drastically reduce the predicted strength of the composite, whereas specimens from different batches of prepreg displayed differences in strength as a function of temperature and extreme moisture exposure. The findings illustrate the need for careful specimen preparation, studies of flaw sensitvity, and careful quality control in any study of composite materials. Previously announced in STAR as N80-33493

Clements, L. L.↗
NASA NTRS1983

Temperature dependence of mechanical and thermal expansion properties of T300/5208 graphite/epoxy

The 116-394 K temperature range elastic constants, ultimate strengths and thermal expansion behavior of T300/5208 graphite/epoxy laminates of various different lay-up types have been determined. It is noted that most properties exhibit nearly linear temperature dependencies, although the transverse modulus and axial thermal expansion vary nonlinearly with temperature, and change in value by an order of magnitude over the present temperature range.

Hyer, M. W.↗
NASA NTRS1983

Wave propagation in a graphite/epoxy laminate

Harmonic wave and wave front propagations in a graphite/epoxy laminate are investigated using a plate theory that includes transverse shear deformation. Transient waves produced by impact of a steel ball are studied experimentally and by using finite elements. The statically measured law of contact between the steel ball and the laminate is used in the finite element program to compute the dynamic contact force. It is found that use of this contact law in conjunction with the finite element modeling of the laminate yields excellent agreement with the experimental results.

Sun, C. T.↗
NASA NTRS1983

Fracto-emission from graphite/epoxy composites

Fracto-emission (FE) is the emission of particles and photons during and following crack propagation. Electrons (EE), positive ions (PIE), and excited and ground state neutrals (NE) were observed. Results of a number of experiments involving principally graphite/epoxy composites and Kevlar single fibers are presented. The physical processes responsible for EE and PIE are discussed as well as FE from fiber- and particulate-reinforced composites.

Dickinson, J. T.↗
NASA NTRS1984

Failure analysis of a graphite/epoxy laminate subjected to bolt bearing loads

Quasi-isotropic graphite/epoxy laminates (T300/5208) were tested under bolt bearing loads to study failure modes, strengths, and failure energy. Specimens had a range of configurations to produce failures by the three nominal failure modes: tension, shearout, and bearing. Radiographs were made after damage onset and after ultimate load to examine the failure modes. Also, the laminate stresses near the bolt hole calculated for each test specimen configuration, and then used with a failure criterion to analyze the test data. Failures involving extensive bearing damage were found to dissipate significantly more energy than tension dominated failures. The specimen configuration influenced the failure modes and therefore also influenced the failure energy. In the width-to-diameter ratio range of 4 to 5, which is typical of structural joints, a transition from the tension mode to the bearing mode was shown to cause a large increase in failure energy. The failure modes associated with ultimate strength were usually different from those associated with the damage onset. Typical damage sequences involved bearing damage onset at the hole boundary followed by tension damage progressing from the hole boundary.

Crews, J. H., Jr.↗
NASA NTRS1984

Hygrothermal effects on mechanical behavior of graphite/epoxy laminates beyond initial failure

An investigation was conducted to determine the critical load levels and associated cracking beyond which a multidirectional laminate can be considered as structurally failed. Graphite/epoxy laminates were loaded to different strain levels up to ultimate failure. Transverse matrix cracking was monitored by acoustic and optical methods. Residual stiffness and strength that were parallel and perpendicular to the cracks were determined and related to the environmental/loading history. Results indicate that cracking density in the transverse layers has no major effect on laminate residual properties as long as the angle ply layers retain their structural integrity. Exposure to hot water revealed that cracking had only a small effect on absorption and reduced swelling when these specimens were compared with uncracked specimens. Cracked, moist specimens showed a moderate reduction in strength when compared with their uncracked counterparts. Within the range of environmental/loading conditions of the present study, it is concluded that the transverse cracking process is not crucial in its effect on the structural performance of multidirectional composite laminates.

Ishai, O.↗
NASA NTRS1983

Physical aging in graphite/epoxy composites

Sub-Tg annealing has been found to affect the properties of graphite/epoxy composites. The network epoxy studied was based on the chemistry of tetraglycidyl 4,4'-diamino-diphenyl methane (TGDDM) crosslinked by 4,4'-diamino-diphenyl sulfone (DDS). Differential scanning calorimetry, thermal mechanical analysis, and solid-state cross-polarized magic-angle-spinning nuclear magnetic resonance spectroscopy have been utilized in order to characterize this process of recovery towards thermodynamic equilibrium. The volume and enthalpy recovery as well as the 'thermoreversibility' aspects of the physical aging are discussed. This nonequilibrium and time-dependent behavior of network epoxies are considered in view of the increasingly wide applications of TGDDM-DDS epoxies as matrix materials of structural composites in the aerospace industry.

Kong, E. S. W.↗
NASA NTRS1983

Environmental effects and viscoelastic behavior of laminated graphite/epoxy composites

Primarily because of the polymeric matrix, graphite/epoxy composites are viscoelastic materials which exhibit creep and delayed failures. Guided by the time-temperature superposition principle, the authors are developing accelerated characterization techniques to predict the long term compliance behavior and creep rupture strength of composite materials based on short term tests at elevated temperatures. The effect of a post-cure cycle on the compliance and creep rupture strength of composite materials is discussed. The Zhurkov type failure law is applied to experimental creep rupture data of a typical laminate and is shown to correlate the data. A beneficial mechanical strengthening effect is described which significantly affects the failure strengths of specimens which have been under creep loading for a period of time. This aging effect is reversible if the specimen is allowed to recover before being loaded to failure. Other environmental aspects of composite materials are also reviewed.

Dillard, D. A.↗
NASA NTRS1983

Bolt clampup relaxation in a graphite/epoxy laminate

A simple bolted joint was analyzed to calculate bolt clampup relaxation for a graphite/epoxy (T300/5208) laminate. A viscoelastic finite element analysis of a double-lap joint with a steel bolt was conducted. Clampup forces were calculated for various steady-state temperature-moisture conditions using a 20-year exposure duration. The finite element analysis predicted that clampup forces relax even for the room-temperature-dry condition. The relaxations were 8, 13, 20, and 30 percent for exposure durations of 1 day, 1 month, 1 year, and 20 years, respectively. As expected, higher temperatures and moisture levels each increased the relaxation rate. The combined viscoelastic effects of steady-state temperature and moisture appeared to be additive. From the finite-element analysis, a simple equation was used to calculate clampup forces for the same temperature-moisture conditions as used in the finite-element analysis. The two sets of calculated results agreed well. Previously announced in STAR as N82-19320

Shivakumar, K. N.↗
NASA NTRS1983

Load sequence effects on graphite/epoxy /+, -35/2s laminates

Load sequence effects on composite material fatigue behavior are due to the difference in residual strength when fatigue occurs, or the 'boundary effect', and the 'material money effect' due to previous loads. The present model, which allows the isolation of the effects of memory from those of boundary, has been investigated through a test program for the case of /+, -35/2s graphite/epoxy laminates under high-low and low-high load sequences which generated statistical residual strength data. As predicted by the model, the memory effect is present and a good correlation is obtained between test results and the theoretical predictions for both median residual strength and the expected percentage of fatigue failures under dual loading. It is noted, however, that the statistical dispersion of the residual strength test results is much smaller than that of the static ultimate strength.

Yang, J. N.↗
NASA NTRS1982

Strain rate characterization of unidirectional graphite/epoxy composite

For an investigation of problems of composites at high strain rates with dominant wave propagation effects, such as dynamically loaded composite jet engine blades, the longitudinal, transverse, and in-plane shear properties of unidirectional SP 288/AS graphite/epoxy were measured at various strain rates ranging from quasi-static to over 500/s. The test specimens were rings 10.16 cm in diameter, 2.54 cm long, 6 to 8 plies thick, and with fibers at 0, 90, and 10 deg off-axis. Quasi-static testing was conducted in a fixture which applies hydraulic pressure to the ring specimens, and dynamic testing was conducted by applying an internal pressure pulse through a liquid in a special fixture. Dynamic stress-strain curves are presented. For the 0-deg specimens, the modulus increases with strain up to 20 percent of the static value. The modulus and strength increase sharply in the 90-deg rings with strain rate reaching values two to three times the corresponding static rate.

Daniel, I. M.↗
NASA NTRS1982

Effect of resin on impact damage tolerance of graphite/epoxy laminates

Twenty-four different epoxy resin systems were evaluated by a variety of test techniques to identify materials that exhibited improved impact damage tolerance in graphite/epoxy composite laminates. Forty-eight-ply composite panels of five of the material systems were able to sustain 100 m/s impact by a 1.27-cm-diameter aluminum projectile while statically loaded to strains of 0.005. Of the five materials with the highest tolerance to impact, two had elastomeric additives, two had thermoplastic additives, and one had a vinyl modifier; all the five systems used bisphenol A as the base resin. An evaluation of test results shows that the laminate damage tolerance is largely determined by the resin tensile properties, and that improvements in laminate damage tolerance are not necessarily made at the expense of room-temperature mechanical properties. The results also suggest that a resin volume fraction of 40 percent or greater may be required to permit the plastic flow between fibers necessary for improved damage tolerance.

Williams, J. G.↗
NASA NTRS1984

Determination of the stiffness reduction of (0,90, + or - N 45) graphite/epoxy laminates under cyclic loading

A series of tests has been performed to determine the effect of fatigue loading on the stiffness degradation of graphite/epoxy composite materials. Specimens were tested in tension-tension fatigue at a loading frequency of 10 Hz and a stress ratio of 0.1, for a wide range of stress levels. During this investigation, both static and dynamic stiffnesses were continually monitored for the range of stress levels tested, and the results are presented in tabular and graphical form.

Jones, D. L.↗