SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A general design procedure is presented for stripline Y-junction circulators employing solid dielectric between ground planes. The resonator design and impedance matching are derived in a form suitable for computer evaluation. The procedure is applicable to cases where either the circulator bandwidth or the ground plane spacing is specified. An experimental S-band switching circulator design illustrates the technique.
An array of microstrip antenna panels was designed for use on a small instrumented satellite as part of a 400-MHz telemetry link between that satellite and NASA's shuttle spacecraft. A roughly omnidirectional phi-plane pattern was desired. The 1.4-wavelength diameter of the satellite and the various ports and structures on its surface presented strong constraints on the antenna array design. Eight antennas, each one a quarter-wavelength panel with one radiating and one shorted edge, were chosen. A phi-plane pattern ripple of 4.4 dB and a gain of at least 0.1 dB relative to a half-wavelength dipole were realized. The design technique used for the individual antenna panels included the study of feed-point location for impedance matching and the effect of losses in the dielectric. A superposition method was used to synthesize the radiation patterns for different numbers and different excitations of antennas on the satellite.
A flush-mounted antenna assembly includes a generally rectangular, conductive, box structure open along one face to form a cavity. Within the cavity a pair of mutually orthogonal dielectric plane surfaces in an "egg crate" arrangement are mounted normal to the plane of the open face, each diagonally within the cavity. Each dielectric plane supports a pair of printed circuit dipoles typically each fed from the opposite side of the dielectric plane by a printed "cone-shaped" feed line trace which also serve as an impedance matching device and functions as a balun connected from an unbalanced strip line external feed. The open face of the conductive cavity can be flush mounted with a randome thereover, the assembly thereby being flush with the skin of a aircraft or space vehicle.
Subharmonically pumped mixers were ascended and tested. A computerized version of the automatic noise figure measurement system was developed. Impedance matching techniques suitable for these types of mixers were investigated. Narrow and broadband (one octave) matching networks for the subharmonic mixers were designed. The automatic mixer noise figure test facility was completed. Subharmonic mixers and the systems that use them at 183 and 220 GHz were evaluated and characterized.
A coupled rotor/airframe vibration analysis developed as a design tool for predicting helicopter vibrations and a research tool to quantify the effects of structural properties, aerodynamic interactions, and vibration reduction devices on vehicle vibration levels is described. The analysis consists of a base program utilizing an impedance matching technique to represent the coupled rotor/airframe dynamics of the system supported by inputs from several external programs supplying sophisticated rotor and airframe aerodynamic and structural dynamic representation. The theoretical background, computer program capabilities and limited correlation results are presented in this report. Correlation results using scale model wind tunnel results show that the analysis can adequately predict trends of vibration variations with airspeed and higher harmonic control effects. Predictions of absolute values of vibration levels were found to be very sensitive to modal characteristics and results were not representative of measured values.
A procedure to control transient signal generation is developed for the study of internal noise propagation from aircraft engines. A simple algorithm incorporating transform techniques is used to produce signals of any desired waveform from acoustic drivers. The accurate driver response is then calculated, and from this the limiting frequency characteristics are determined and the undesirable frequencies where the driver response is poor are eliminated from the analysis. A synthesized signal is then produced by convolving the inverse of the response function with the desired signal. Although the shape of the synthesized signal is in general quite awkward, the driver generates the desired signal when the distorted signal is fed into the driver. The results of operating the driver in two environments, in a free field and in a duct, are presented in order to show the impedance matching effect of the driver. In addition, results using a high frequency cut-off value as a parameter is presented in order to demonstrate the extent of the applicability of the synthesis procedure. It is concluded that the desired signals can be generated through the signal synthesis procedure.
The optimum design choice for the MST radar antenna was considered. The following factors are required: directivity and gain; beam width and its symmetry; sidelobe levels, near and wide angle; impedance matching; feeder network losses; polarization diversity; steerability; cost effectiveness; and maintainability. The directivity and related beam forming aspects of various antenna elements and directivity aspects when such elements are formed into an array are discussed. Array performance for important variables, in particular, the spacing of the elements is considered.
In the case of modern infrared focal planes, one of the major problems is related to the noise contribution of the cooled, impedance-matching device used as the preamplifier stage in the detector electronics system. An ideal preamp device should have the low-noise advantages of a buried-channel device and operate isothermally with the low-temperature detector array. The Ge JFET might provide this ideal device. A testing program with Ge JFETs is discussed. It is concluded that germanium JFETs offer an attractive alternative for cryogenic preamplifier designs. They operate well with high transconductance and low noise at LHe temperatures. It is believed that these devices point the way for the development of large, integrated-array, long wavelength, infrared focal planes which incorporate germanium detectors, germanium load resistors, and germanium preamplifiers within the same monolithic structure.
A parametric study was conducted to develop an electrooptic waveguide modulator for generating continuous tunable sideband power from an infrared CO2 laser. Parameters included were the waveguide configurations, microstrip dimensions device impedance, and effective dielectric constants. An optimum infrared laser modulator was established and was fabricated. This modulator represents the state-of-the-art integrated optical device, which has a three-dimensional topology to accommodate three lambda/4 step transformers for microwave impedance matching at both the input and output terminals. A flat frequency response of the device over 20 HGz or = 3 dB) was achieved. Maximum single sideband to carrier power greater than 1.2% for 20 W microwave input power at optical carrier wavelength of 10.6 microns was obtained.
Considerable progress has been made in the calculation and measurement of the scattering parameters of printed circuit discontinuities. These discontinuities occur in a variety of structures, such as transitions between rectangular waveguide and printed circuits, junctions between circuits of different dielectric constants, and filters and impedance matching circuits. Because of the variety of devices in which these discontinuities occur, it is very useful to understand them in as great a detail as possible. Both theoretical and experimental studies of discontinuities were considered. The theoretical studies have focused on finding ways to predict the scattering from discontinuities. The experimental studies have concentrated on developing measurement techniques for determining the scattering parameters of these discontinuities.
The deposition of semiconducting and insulating thin films at low temperatures using microwave technology was explored. The method of plasma formations, selection of a power source, the design of the microwave plasma cavity, the microwave circuitry, impedance matching, plasma diagnostics, the deposition chamber and the vacuum system were studied.
The development and performance is described of a high-gain antenna designed to serve on the Pioneer Venus Orbiter spacecraft as a backup to the principal high-gain antenna unit in the unlikely event the mechanically despun antenna mechanism malfunctioned. The final design, a center-fed standing wave array of six sleeve dipoles enclosed in a fiber glass radome, performed successfully, as did all the antennas, on the Pioneer Orbiter spacecraft which was launched on May 20, 1978, as part of the Pioneer Venus mission. Photographs of experimental models giving details of design and construction are included, as well as graphs showing measured pattern and impedance matching characteristics of the subject antenna.
Parts made on printed-circuit boards. Impedance-matching and power-dividing transmission-line strips formed on insulation disks and on board by printed-circuit techniques. Power from input transmission line sent equally through radial output conductors to radial output transmission lines and/or coupled in varying degrees to axial output transmission line.
Fixtures and techniques are undergoing development. Four test fixtures and two advanced techniques developed in continuing efforts to improve RF characterization of MMIC's. Finline/waveguide test fixture developed to test submodules of 30-GHz monolithic receiver. Universal commercially-manufactured coaxial test fixture modified to enable characterization of various microwave solid-state devices in frequency range of 26.5 to 40 GHz. Probe/waveguide fixture is compact, simple, and designed for non destructive testing of large number of MMIC's. Nondestructive-testing fixture includes cosine-tapered ridge, to match impedance wavequide to microstrip. Advanced technique is microwave-wafer probing. Second advanced technique is electro-optical sampling.
Thermal waves generated by either turbine rotor blades cutting through nonuniform combustor temperature fields or unsteady burning could lead to thermal fatigue cracking in the blades. To determine the magnitude of the thermal oscillation in blades with complex shapes and material compositions, a finite element Galerkin formulation has been developed to study combustor generated thermal wave propagation in a model two-dimensional duct with a uniform plug flow profile. The reflection and transmission of the thermal waves at the entrance and exit boundaries are determined by coupling the finite element solutions at the entrance and exit to the eigenfunctions of an infinitely long adiabatic duct. Example solutions are presented. In general, thermal wave propagation from an air passage into a metallic blade wall is small and not a problem. However, if a thermal barrier coating is applied to a metallic surface under conditions of a high heat transfer, a good impedance match is obtained and a significant portion of the thermal wave can pass into the blade material.
An L-band circularly polarized microstrip array antenna with relatively wide bandwidth has been developed. The array has seven subarrays which form a single cluster as part of a large overlapping cluster reflector feed array. Each of the seven subarrays consists of four uniquely arranged linearly polarized microstrip elements. A 7.5 percent impedance (VSWR less than 1.5) as well as axial ratio (less than 1 dB) bandwidths have been achieved by employing a relatively thick honeycomb substrate with special impedance matching feed probes.
To meet the requirements for the output switch of an ultra-high-power (greater than 30 GW) pulser, an upgrading design for an inverse-pinch plasma switch (INPIS) is considered. The hold-off voltage of 1 MV is met by adopting multistage rim-fire electrodes and using SF6 as the dielectric gas of the switch. The inductance and capacitance of the switch, which are restricted by the short rise-time (less than 0.1 microsec) requirement, were met by adjusting the dimensions of the coaxial electrodes of the switch. The input/output transmission lines attached to the switch will be immersed in oil to meet the high voltage insulation and impedance-matching requirements. Since the forwarding current is relatively low with respect to the switch capability, the lifetime of the switch is expected to exceed the requirement of 10,000 shots.
Thermal waves generated by either turbine rotor blades cutting through nonuniform combustor temperature fields or unsteady burning could lead to thermal fatigue cracking in the blades. To determine the magnitude of the thermal oscillation in blades with complex shapes and material compositions, a finite element Galerkin formulation has been developed to study combustor generated thermal wave propagation in a model two-dimensional duct with a uniform plug flow profile. The reflection and transmission of the thermal waves at the entrance and exit boundaries are determined by coupling the finite element solutions at the entrance and exit to the eigenfunctions of an infinitely long adiabatic duct. Example solutions are presented. In general, thermal wave propagation from an air passage into a metallic blade wall is small and not a problem. However, if a thermal barrier coating is applied to a metallic surface under conditions of a high heat transfer, a good impedance match is obtained and a significant portion of the thermal wave can pass into the blade material.