Search NASA⌕ Search

SEARCH · Search NASA

Results for “Interfacial bonding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Chemical Passivation of Crystalline Si by Al 2 O 3 Deposited Using Atomic Layer Deposition: Implications for Solar Cells

The atomistic-level mechanism for the chemical passivation of the monocrystalline Si (c-Si) surface with thermally annealed Al 2 O 3 was studied using in situ infrared spectroscopy and photoconductance decay measurements. Al 2 O 3 was deposited on high-lifetime, float-zone c-Si substrates using atomic layer deposition (ALD) from trimethylaluminum (TMA), and H 2 O or O 3 . Surface-sensitive attenuated total reflection Fourier transform infrared spectroscopy was used to monitor the c-Si/Al 2 O 3 interface, as well as the bulk of the Al 2 O 3 film during the entire process. Our results show that some surface Si–H bonds are preserved after the ALD of Al 2 O 3 on H-terminated Si. During the annealing step at 400 °C, restructuring occurs at the c-Si/Al 2 O 3 interface to form interfacial SiO x . Isotope labeling was used to differentiate interfacial SiD bonds on the c-Si surface from H incorporated in Al 2 O 3 . Within the sensitivity of our infrared setup (~10 13 cm –2 ), we did not observe any net migration of atomic H or D from Al 2 O 3 to the c-Si/Al 2 O 3 interface. To isolate the effects of chemical and field-effect passivation of Al 2 O 3 thin films, we carried out surface passivation studies on c-Si/SiO 2 /Al 2 O 3 stacks. We also annealed these stacks in different atmospheres to test the influence of annealing atmospheres on the chemical passivation of c-Si by Al 2 O 3 and observed that O 2 -containing atmosphere led to the best surface chemical passivation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Dative Epitaxy of Commensurate Monocrystalline Covalent van der Waals Moiré Supercrystal

Realizing van der Waals (vdW) epitaxy in the 1980s represents a breakthrough that circumvents the stringent lattice matching and processing compatibility requirements in conventional covalent heteroepitaxy. However, due to the weak vdW interactions, there is little control over film qualities by the substrate. Typically, discrete domains with a spread of misorientation angles are formed, limiting the applicability of vdW epitaxy. In this study, the epitaxial growth of monocrystalline, covalent Cr 5 Te 8 2D crystals on monolayer vdW WSe 2 by chemical vapor deposition is reported, driven by interfacial dative bond formation. The lattice of Cr 5 Te 8 , with a lateral dimension of a few tens of micrometers, is fully commensurate with that of WSe 2 via 3 × 3 (Cr 5 Te 8 )/7 × 7 (WSe 2 ) supercell matching, forming a single-crystalline moiré superlattice. This work establishes a conceptually distinct paradigm of thin-film epitaxy, termed “dative epitaxy”, which takes full advantage of covalent epitaxy with chemical bonding for fixing the atomic registry and crystal orientation, while circumventing its stringent lattice matching and processing compatibility requirements; conversely, it ensures the full flexibility of vdW epitaxy, while avoiding its poor orientation control. Cr 5 Te 8 2D crystals grown by dative epitaxy exhibit square magnetic hysteresis, suggesting minimized interfacial defects that can serve as pinning sites.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Lattice-scale variations in viscosity are correlated with solution structure at mineral-water interfaces

At solid-liquid interfaces, the viscosity increases markedly from the bulk due to the collective interactions of ions and water molecules, influencing phenomena relevant to nanofluidics, colloidal dynamics, and electrochemistry. Here, in this study, we investigated dissipative forces at the boehmite-water interface using 3D atomic force microscopy. We observed an increase in interfacial solution viscosity, η, by 10-100-fold as the nanoprobe approached the surface in normal direction, with up to four oscillatory features showing average peaks of η/η bulk = 44-71. Moreover, the viscosity showed sub-nanometer variations within 0.5 nm from the interface, templated by the underlying crystal lattice and correlated with the interfacial solution structure. Beyond a near-wall region of approximately 1.2 nm, the dissipative response was comparable to that in bulk solution. Molecular dynamics simulations, along with statistical mechanical analyses, provided details on hydrodynamic structures near the interface. Specifically, the lattice-dependent dissipative responses are correlated with extensive hydrogen bonding by interfacial water molecules, which increased friction, particularly along the [001] direction. These results demonstrate how solution viscosity at mineral-water interfaces is anisotropic and correlated with the local solution structure, providing insights into the dynamics of nanocrystal attachment.

Viscosity↗
DOE OSTI2023

Microstructural, Corrosion and Mechanical Characterization of Friction-Stir Welded Joints Between Aluminum and Magnesium Alloys

Friction Stir Welding (FSW) of Aluminum-Magnesium (Al-Mg) alloys has garnered increasing attention due to its wide-ranging applications in the automotive and aerospace industries. The microstructural, corrosion, and mechanical properties of FSW Al-Mg welds under selected conditions are critical factors that must be well-investigated to ensure their durability and performance. In this study, electrochemical tests, including Open Circuit Potential (OCP), Linear Polarization Resistance (LPR), Potentiodynamic Polarization Scan (PD), and Electrochemical Impedance Spectroscopy (EIS), have been used to analyze the corrosion resistance of these welds, along with weight loss measurements through cyclic corrosion testing (CCT) and surface evolution via SEM over an 8-week period. Mechanical properties are evaluated through microindentation, nanoindentation, fatigue, and lap-shear tests. The results of the electrochemical tests reveal that the corrosion properties of the center weld zone differ from those of the two base alloys. Indentation tests indicate that the weld zone behaves differently from the base alloys. Surprisingly, the lap shear strength did not decrease significantly even after 8 weeks of cyclic corrosion testing, indicating that the joint prevented any ingress of the electrolyte. Fatigue testing showed that applying an adhesive between the Al and Mg joint improved the fatigue life to some extent, although the corrosion resistance reduced due to the discontinuous bonding of the adhesive layer. Overall, these findings highlight the importance of investigating the corrosion and mechanical properties of FSW Al-Mg welds and provide valuable insights for future modeling works.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Aluminum/SmCo 5 composites for structural and magnetic applications

Metal-bonded magnetic composites (MBMCs) present a promising alternative to dense sintered magnets, particularly for intricate components. Compared to polymer-based bonded magnets, MBMCs have wider applicability in harsh environments. In this paper, we demonstrate a solid-state shear-based manufacturing technique to introduce localized magnetization into a paramagnetic aluminum matrix by embedding SmCo5 permanent magnet particles. Our magnetic composites display hard magnetic behavior with a coercivity of 13 kOe and a remanent magnetization of 4.32 emu/g. In addition to magnetization, we also report a 9% improvement in Young’s modulus. Despite the local temperature rise during processing, the magnetic phases didn’t decompose into unwanted phases, preserving the composite's hard magnetic properties. Creation of an interfacial metallurgical bond with the matrix ensured the suitability of the composites for structural applications. Our study investigates the mechanical, and functional properties of composites, paving the way for lightweight structural magnetic composites with a transformative potential in the aerospace, nuclear, and automotive applications. This work underscores the potential for further optimization and development to drive innovations in magnet and equipment design.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Characterization of Temporal Changes of Interfacial Air Voids During Adhesive Curing and Bonding for Adhesively-Bonded Structures

This paper studied the evolution of air voids at the substrate-adhesive interface during the curing and bonding process of an epoxy-based adhesive between two glass substrates due to the sequence of adhesive placement, external pressure, and plasma treatment on substrates for bonding. The experimental results showed that a higher quantity of interfacial voids were generated during adhesive curing when the substrate was attached to the adhesive compared to when the adhesive was applied and distributed on the substrate. Such interfacial voids can be efficiently removed or reduced by applying slight pressure on the bonded structure during adhesive curing, or by leveraging plasma-treated substrates, as less reported in the literature. This work provided practical suggestions for preparing adhesive joints with minimized interfacial air voids to enhance bonding performance, particularly for dissimilar joints such as metal-CFRTP (carbon-fiber-reinforced thermoplastic polymer), as well as combinations with different types of polymer composites.

Qiao, Yao [BATTELLE (PACIFIC NW LAB)] (ORCID:00000↗
DOE OSTI2026

Ultrafast (1‐5 sec) Lamination of Perovskite Solar Cells With Self‐Encapsulation Using Rapid Joule Heating

Perovskite solar cells (PSCs) are traditionally fabricated using sequential layer‐by‐layer deposition, in which each layer of the device is processed on top of the preceding layer. This constrains the processing techniques and selection of transport layer materials that can be used in the solar cell. To overcome these challenges, two half‐cells can be processed independently and then diffusion‐bonded through a lamination process. However, current lamination processes for perovskite solar cells suffer from relatively long process times, which can limit throughput when moving toward high‐volume manufacturing. In this study, a custom platform was designed for rapid‐joule heating of perovskite materials and devices. This enabled more than a 99% reduction in lamination time from 26 min to 1 s. Perovskite samples that were laminated in 1 s exhibited comparable values of percent bonded area, interfacial toughness, grain domain size, and X‐ray diffraction spectra to those laminated in greater than 10 min. As a proof‐of‐concept, 18.3% efficient devices were successfully laminated in 5 s. A transient heat transfer model was developed to describe the relationship between the perovskite temperature and the electrical power supplied to the heaters, establishing a baseline for predicting processing conditions in large‐scale manufacturing systems. Ultra‐fast lamination provides a pathway toward scalable roll‐to‐roll or sheet‐to‐sheet manufacturing of PSCs.

heat transfer↗
DOE OSTI2024

Thermal Transport and Mechanical Stress Mapping of a Compression Bonded GaN/Diamond Interface for Vertical Power Devices

Bonding diamond to the back side of gallium nitride (GaN) electronics has been shown to improve thermal management in lateral devices; however, engineering challenges remain with the bonding process and characterizing the bond quality for vertical device architectures. Here, in this study, integration of these two materials is achieved by room-temperature compression bonding centimeter-scale GaN and a diamond die via an intermetallic bonding layer of Ti/Au. Recent attempts at GaN/diamond bonding have utilized a modified surface activation bonding (SAB) method, which requires Ar fast atom bombardment immediately followed by bonding within the same tool under ultrahigh vacuum (UHV) conditions. The method presented here does not require a dedicated SAB tool yet still achieves bonding via a room-temperature metal–metal compression process. Imaging of the buried interface and the total bonding area is achieved via transmission electron microscopy (TEM) and confocal acoustic scanning microscopy (C-SAM), respectively. The thermal transport quality of the bond is extracted from spatially resolved frequency-domain thermoreflectance (FDTR) with the bonded areas boasting a thermal boundary conductance of >100 MW/m 2 ·K. Additionally, Raman maps of GaN near the GaN–diamond interface reveal a low level of compressive stress, <80 MPa, in well-bonded regions. FDTR and Raman were coutilized to map these buried interfaces and revealed some poor thermally bonded areas bordered by high-stress regions, highlighting the importance of spatial sampling for a complete picture of bond quality. Overall, this work demonstrates a novel method for thermal management in vertical GaN devices that maintains low intrinsic stresses while boasting high thermal boundary conductances.

Raman↗
DOE OSTI2022

Lead-Free Flexible Perovskite Solar Cells with Interfacial Native Oxide Have >10% Efficiency and Simultaneously Enhanced Stability and Reliability

Here we demonstrate an innovative compositional and interfacial engineering approach to achieve Pb-free flexible perovskite solar cells (f-PSCs) with an unprecedented combination of the highest efficiency reported to date (10.43%), together with enhanced operational stability and mechanical reliability. The key to this approach is alloying of an FASnI3 metal halide perovskite (MHP) thin film with Ge2+ to stabilize the Sn2+ oxidation state in the MHP, together with the use of a NiOx hole-transport layer. We show that this results in the in situ formation of a thin amorphous GeO2 native oxide layer at the NiOx/FASn0.9Ge0.1I3 interface. This layer not only passivates that critical interface but also enhances the interfacial mechanical bonding.

efficiency↗
DOE OSTI2025

Bio-inspired multiscale design for perovskite solar cells

Metal halide perovskite semiconductors have attractive light-harvesting and charge-carrier transport properties for photovoltaics. Perovskite solar cells (PSCs) and modules have demonstrated their commercial promise with high power conversion efficiencies, but still face stability challenges. In this Review, we explore how biomaterials offer design inspiration for the development of durable and efficient PSCs at three different scales. At the molecular level, bio-inspired molecular interactions are harnessed towards crystallization control and degradation prevention, which offers an enhancement in long-term maximum-power-point tracking stability. At the microstructural level, self-healing and strength-enhancing strategies, utilizing dynamic bonds and interfacial reinforcement, can help PSCs to recover from physical damage and maintain high performance. At the device level, macroscopic functionalities, such as moth-eye-inspired structures tailored to different layers, can collectively enable antireflection, radiative cooling and self-cleaning to optimize light management, heat dissipation and encapsulation in PSCs. Bio-inspired PSC research can combine improved efficiency and lifetime, with abundant, biocompatible alternatives to conventional stabilizers. Future efforts should focus on screening bioinspired molecules to optimize film crystallization and stability, developing self-healing mechanisms triggered by operational stress, designing cost-efficient biomicrostructures, and integrating multifunctional encapsulation to enhance the efficiency and lifespan of PSCs.

Duan, Tianwei↗
DOE OSTI2023

Relaxing Wrinkles in Jammed Interfacial Assemblies

Dynamic covalent bonding has emerged as a mean by which stresses in a network can be relaxed. Here, the strength of the bonding of ligands to nanoparticles at the interface between two immiscible liquids affect the same results in jammed assemblies of nanoparticle surfactants. Beyond a critical degree of overcrowding induced by the compression of jammed interfacial assemblies, the bonding of ligands to nanoparticles (NPs) can be broken, resulting in a desorption of the NPs from the interface. This reduces the areal density of nanoparticle surfactants at the interface, allowing the assemblies to relax, not to a fluid state but rather another jammed state. The relaxation of the wrinkles caused by the compression reflects the tendency of these assemblies to eliminate areas of high curvature, favoring a more planar geometry. Importantly, this enabled the generation of giant vesicular and multivesicular structures from these assemblies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Selective modifiers for composite material property enhancement

A laminate comprising a first ply, a second ply, and a plurality of interfacial modifiers arranged between opposing faces of the first ply and the second ply. A chemical composition of an interfacial modifier of the plurality of interfacial modifiers can be selected based on a resulting bond strength between the interfacial modifier of the plurality of interfacial modifiers and at least one of the first ply or the second ply. The plurality of interfacial modifiers can be arranged in a pattern to selectively modify toughness of a portion of the laminate based on the bond strength of the interfacial modifier of the plurality of interfacial modifiers.

Briggs, Timothy↗
DOE OSTI2023

Relaxing Wrinkles in Jammed Interfacial Assemblies

Abstract Dynamic covalent bonding has emerged as a mean by which stresses in a network can be relaxed. Here, the strength of the bonding of ligands to nanoparticles at the interface between two immiscible liquids affect the same results in jammed assemblies of nanoparticle surfactants. Beyond a critical degree of overcrowding induced by the compression of jammed interfacial assemblies, the bonding of ligands to nanoparticles (NPs) can be broken, resulting in a desorption of the NPs from the interface. This reduces the areal density of nanoparticle surfactants at the interface, allowing the assemblies to relax, not to a fluid state but rather another jammed state. The relaxation of the wrinkles caused by the compression reflects the tendency of these assemblies to eliminate areas of high curvature, favoring a more planar geometry. This enabled the generation of giant vesicular and multivesicular structures from these assemblies.

Xie, Ganhua↗
DOE OSTI2022

Effects of ion adsorption on graphene oxide films and interfacial water structure: A molecular-scale description

Herein we discuss graphene oxide as a promising, emerging separation material, as it is durable, dispersible in water, and has naturally forming functional groups. Bulk studies using graphene oxide flakes have demonstrated impressive metal adsorption. However, little interfacial information about water and metal organization near graphene oxide is available. A mechanistic understanding of water and ions interactions with graphene oxide films is critical toward advanced separations, including improved sorption efficiency and membrane regeneration. We study metal ion and local water organization near graphene oxide thin films formed at the air/water interface. These films are not typical membranes and allow us to determine nanoscale information about the graphene oxide-water interface. We accomplish this with x-ray reflectivity (XR), x-ray fluorescence near total reflection (XFNTR), and vibrational sum frequency generation spectroscopy (SFG). These interface-specific techniques provide the electron density profile normal to the interface, number of adsorbed ions, and information about the orientational ordering and hydrogen-bonding network of interfacial water, respectively. Via XFNTR and SFG, we find that trivalent yttrium ions preferentially adsorb to graphene oxide and affect its structure, compared to divalent strontium and monovalent cesium ions. Two different interfacial water populations can be described, based on their hydrogen bonding strength, and the adsorbed ions affect these populations differently. These results provide fundamental information about ion and water organization at the interface and help address the large computational-experimental agreement gap for graphene oxide systems. Additionally, they are relevant for improved soft-scaffold graphene oxide membranes and downstream applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Squeezing Out Interfacial Solvation: The Role of Hydrogen-Bonding in the Structural and Orientational Freedom of Molecular Self-Assembly

We report bioinspired membrane molecules with improved physical properties and enhanced stability can serve as functional models for conventional lipid or amphiphilic species. Importantly, these molecules can also provide new insights into emergent phenomena that manifest during self-assembly at interfaces. Here, we elucidate the structural response and mechanistic steps underlying the self-assembly of the amphiphilic, charged oligodimethylsiloxane imidazolium cation (ODMS-MIM+) at the air–aqueous interface using Langmuir trough methods with coincident surface-specific vibrational sum-frequency generation (SFG) spectroscopy. We find evidence for a new compression-induced desolvation step that precedes commonly known disordered-to-ordered phase transitions to form nanoscopic assemblies. The experimental data was supported by atomistic molecular dynamics (MD) simulations to provide a detailed mechanistic picture underlying the assembly and the role of water in these phase transitions. The sensitivity of the hydrophobic ODMS tail conformations to compression-owing to distinct water–ODMS interactions and tail–tail solvation properties-offers new strategies for the design of interfaces that can be further used to develop soft-matter electronics and low-dimensional materials using physical and chemical controls.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗