Search NASA⌕ Search

SEARCH · Search NASA

Results for “Intermodule”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A K-band GaAs FET amplifier with 8.2-W output power

An 8.2-W GaAs FET amplifier with 38.6 + or - 0.5-dB gain over a 17.7-19.1-GHz frequency band has been developed. This amplifier combines the outputs of eight multistage amplifier modules utilizing a radial combiner. This state-of-the art power level has been achieved with AM/PM of less than 2 deg/dB. The third-order intermodulation products at 1-dB gain compression were 20 dBc, and variation in group delay over the frequency band was less than + or - 0.25 ns. Tests show that the amplifier is unconditionally stable and follows the graceful-degradation principle.

Goel, J.↗
NASA NTRS1985

Shuttle S-band communications technical concepts

Using the S-band communications system, shuttle orbiter can communicate directly with the Earth via the Ground Spaceflight Tracking and Data Network (GSTDN) or via the Tracking and Data Relay Satellite System (TDRSS). The S-band frequencies provide the primary links for direct Earth and TDRSS communications during all launch and entry/landing phases of shuttle missions. On orbit, S-band links are used when TDRSS Ku-band is not available, when conditions require orbiter attitudes unfavorable to Ku-band communications, or when the payload bay doors are closed. the S-band communications functional requirements, the orbiter hardware configuration, and the NASA S-band communications network are described. The requirements and implementation concepts which resulted in techniques for shuttle S-band hardware development discussed include: (1) digital voice delta modulation; (2) convolutional coding/Viterbi decoding; (3) critical modulation index for phase modulation using a Costas loop (phase-shift keying) receiver; (4) optimum digital data modulation parameters for continuous-wave frequency modulation; (5) intermodulation effects of subcarrier ranging and time-division multiplexing data channels; (6) radiofrequency coverage; and (7) despreading techniques under poor signal-to-noise conditions. Channel performance is reviewed.

Seyl, J. W.↗
NASA NTRS1986

Linearized traveling wave amplifier with hard limiter characteristics

A dynamic velocity taper is provided for a traveling wave tube with increased linearity to avoid intermodulation of signals being amplified. In a traveling wave tube, the slow wave structure is a helix including a sever. A dynamic velocity taper is provided by gradually reducing the spacing between the repeating elements of the slow wave structure which are the windings of the helix. The reduction which takes place coincides with the ouput point of helix. The spacing between the repeating elements of the slow wave structure is ideally at an exponential rate because the curve increases the point of maximum efficiency and power, at an exponential rate. A coupled cavity traveling wave tube having cavities is shown. The space between apertured discs is gradually reduced from 0.1% to 5% at an exponential rate. Output power (or efficiency) versus input power for a commercial tube is shown.

Kosmahl, H. G.↗
NASA NTRS1987

Technology for submillimeter wave remote sensing

NASA's sub-mm wave technology development program addresses emerging possibilities in spaceborne sensor design for what is one of the few unexplored regions of the spectrum, from 1.0 to 0.1 mm wavelengths. Astrophysics, earth atmosphere research and solar system exploration can all benefit from the development of such sensor capabilities. Technology status evaluations are presented for Shottky-diode and SIS mixers, solid state and backward wave oscillators, intermodulation frequency amplifiers, and digital autocorrelator and acoustooptic spectrometers.

Sokoloski, Martin M.↗
NASA NTRS1988

Embedding triple-modular redundancy into a hypercube architecture

This paper describes an embedding of Triple Modular Redundancy (TMR) into a binary hypercube. The goal is to improve fault tolerance by masking any single-point faults. Each module of an application task is triplicated and executed in parallel on three nodes of a 2-dimensional subcube (Q2) of the hypercube. Each of these nodes also executes a voter process. The remaining node is used for message passing only. All outputs from the triplicated modules are voted on, and the voting results are transmitted to the appropriate destination. Thus, all interunit messages are also triplicated. We propose an embedding of TMR into a hypercube which can be implemented in a manner transparent to the application program. Subcubes are allocated so that the address space for the TMR units is also a hypercube. Hence, the subcube allocation and intermodule communication schemes are defined to be analogous to the schemes used in the nonredundant system. The embedded system is proven to mask all single-point faults.

Kiskis, Daniel L.↗
NASA NTRS1988

The International Space Station complex - Promise and problems

The current planning status of the International Space Station is reviewed from a NASA perspective, with a focus on aspects affecting the contributions of the international partners ESA, Japan, and Canada. The modifications implied by the shift from the previous double-keel configuration to the current phased-deployment (Block 1 - Block 2) approach are considered in detail and illustrated with drawings and a table listing the baseline assembly sequence. It is pointed out that the originally proposed non-NASA components can all be accommodated in the new configuration. The need for intermodule commonality of equipment form, fit, and function is discussed, and it is recommended that independent user boards be set up to select and coordinate experiments, and that the user boards of the partners open channels of cooperation and mutual support.

Halpern, Richard E.↗
NASA NTRS1988

Simultaneous S- and X-band uplink-downlink performance at DSS 13

The Deep Space Station 13 26-meter antenna with the second generation S/X feedcone was tested to determine the dual S- and X-band (2.1 to 2.3 GHz and 7.1 to 8.5 GHz) transmit and receive performance. Measurements were conducted using the 20 kW transmitters at S- and X-band while simultaneously receiving S- and X-band. This system proved to be very quiet compared with the other DSN antennas. Under normal tracking configurations, no noise burst or intermodulation product (IMP) activity was detectable to the -175 dBm level. To prove the instrumentation's ability to detect such phenomena, an IMP generator was introduced onto the system with positive, verifiable results. The IMP occurred at the -162 dBm level, accompanied by moderate noise burst activity, and was readily repeatable. The measurement also showed the possible need for additional fourth channel filtering in the system to reduce the effect of the transmitter power on the low noise amplifiers.

Freiley, A. J.↗
NASA NTRS1989

The permanent electric dipole moment of chromium monoxide

The permanent electric dipole moments for the X 5Pi and B 5pi states of gas-phase CrO have been experimentally determined using the sub-Doppler optical technique of intermodulated fluorescence spectroscopy in conjunction with the Stark effect. The measured values are 3.88 + or - 0.13 and 4.1 + or - 1.8 D for the X and B states, respectively. The theoretical values determined for the X state using multireference CI iterative-natural-orbital and finite-field calculations are in excellent agreement with the experimental value.

Steimle, Timothy C.↗
NASA NTRS1989

Simulation and analysis of an intermediate frequency (IF) distribution system with applications for Space Station

Simulation and analysis results are described for a wideband fiber optic intermediate frequency distribution channel for a frequency division multiple access (FDMA) system where antenna equipment is remotely located from the signal processing equipment. The fiber optic distribution channel accommodates multiple signals received from a single antenna with differing power levels. Performance parameters addressed are intermodulation degradations, laser noise, and adjacent channel interference, as they impact the overall system design. Simulation results showed that the laser diode modulation level can be allowed to reach 100 percent without considerable degradation. The laser noise must be controlled as to provide a noise floor of less than -90 dBW/Hz. The fiber optic link increases the degradation due to power imbalance yet diminishes the effects of the transmit amplifier nonlinearity. Overall, optimal operation conditions can be found to yield a degradation level of about .1 dB caused by the fiber optic link.

Costello, Thomas A.↗
NASA NTRS1991

Improved algorithms for mapping pipelined and parallel computations

Recent work on the problem of mapping pipelined or parallel computations onto linear array, shared memory, and host-satellite systems is extended. It is shown how these problems can be solved even more efficiently when computation module execution times are bounded from below, intermodule communication times are bounded from above, and the processors satisfy certain homogeneity constraints. The improved algorithms have significantly lower time and space complexities than the more general algorithms: in one case, an O(nm3) time algorithm for mapping m modules onto n processors is replaced with an O(nm log m) time algorithm, and the space requirements are reduced from O(nm2) to O(m). Run-time complexity is reduced further with parallel mapping algorithms based on these improvements, which run on the architectures for which they create mappings.

Nicol, David M.↗
NASA NTRS1991

Space Station resource node flow field analysis

An analysis of the flow field within the Space Station Freedom resource node with operational intermodule ventilation and temperature/humidity control ventilation systems has been conducted. The INS3D code, an incompressible, steady-state Navier-Stokes solver has been used to assess the design of the ventilation system via quantification of the level of fluid mixing and identification of 'dead air' regions and short-circuit ventilation. Numerical results indicate significant short-circuit ventilation in the forward and midsections of the node and insufficient fluid mixing is found to exist in the aft node section. These results as well as results from a solution grid dependence study are presented.

Kania, Lee↗
NASA NTRS1991

Appendices B thru F, volume 3

The purpose of this investigation was to determine if the intermodule ventilation (IMV) systems and water distribution systems of Space Station Freedom (SSF) modules and nodes should be connected as they are interfaced with those already in operation. It was concluded that the AC configuration and attached LAB and HAB modules and nodes should be interconnected. The H2O circuits should also be interconnected. Interconnecting the air and water provides flexibility of operation and safety comparable to the Assembly Complete (AC) configuration. This requires only only that valves and ducts be provided in the AC nodes. The AC node interfaces should also be scarred to provide for water transfer across these interfaces. Penalties for not connecting the Intermodular Ventilation (IMV) system and water circuits include an additional AR unit, possible increased water storage requirements, and considerable reduction in crew flexibility.

Source record↗
NASA NTRS1991

Advanced life support study

Summary reports on each of the eight tasks undertaken by this contract are given. Discussed here is an evaluation of a Closed Ecological Life Support System (CELSS), including modeling and analysis of Physical/Chemical Closed Loop Life Support (P/C CLLS); the Environmental Control and Life Support Systems (ECLSS) evolution - Intermodule Ventilation study; advanced technologies interface requirements relative to ECLSS; an ECLSS resupply analysis; the ECLSS module addition relocation systems engineering analysis; an ECLSS cost/benefit analysis to identify rack-level interface requirements of the alternate technologies evaluated in the ventilation study, with a comparison of these with the rack level interface requirements for the baseline technologies; advanced instrumentation - technology database enhancement; and a clean room survey and assessment of various ECLSS evaluation options for different growth scenarios.

Source record↗
NASA NTRS1990

Space segment configuration of the Canadian mobile satellite system

The performance requirements, the main parameters, and the configuration of the MSAT spacecraft are reviewed. The major features of the communications subsystem are discussed in some detail. Key technology items include the L-band Radio Frequency (RF) power amplifier which must operate with a high DC to RF power efficiency and generate low intermodulation when loaded with multi-carrier signals; and the large diameter deployable L-band antenna. The development status and expected performance of these spacecraft components is examined.

Bertenyi, Elemer↗
NASA NTRS1990

The design of a linear L-band high power amplifier for mobile communication satellites

A linear L-band solid state high power amplifier designed for the space segment of the Mobile Satellite (MSAT) mobile communication system is described. The amplifier is capable of producing 35 watts of RF power with multitone signal at an efficiency of 25 percent and with intermodulation products better than 16 dB below carrier.

Whittaker, N.↗
NASA NTRS1991

Interfaces for high-speed fiber-optic links - Analysis and experiment

An analysis of directly and externally modulated fiberoptic links is presented. The theoretical analysis is based on the signal flow diagram of the interface circuits to the laser diode, Mach-Zehnder electro-optic modulator, and p-i-n photodiode. System parameters such as gain, noise figure, two-tone intermodulation distortion, and spurious free and compression dynamic range are expressed as a function of frequency and operating point of the laser and external modulator. Two directly and externally modulated fiber-optic links were designed and fabricated to verify the analytical models. The direct modulation FO link was developed at the Ku-band (11.6-12.4 GHz), whereas the external modulation link was at L-band (875-925 MHz). Spurious-free dynamic ranges of 95.8 dB-Hz exp 2/3 and 113 dB-Hz exp 2/3, respectively, were achieved. The predictions based on the analytical models match the measured results.

Daryoush, Afshin S.↗
NASA NTRS1992

Self-checking self-repairing computer nodes using the mirror processor

Circuitry added to fault-tolerant systems for concurrent error deduction usually reduces performance. Using a technique called micro rollback, it is possible to eliminate most of the performance penalty of concurrent error detection. Error detection is performed in parallel with intermodule communication, and erroneous state changes are later undone. The author reports on the design and implementation of a VLSI RISC microprocessor, called the Mirror Processor (MP), which is capable of micro rollback. In order to achieve concurrent error detection, two MP chips operate in lockstep, comparing external signals and a signature of internal signals every clock cycle. If a mismatch is detected, both processors roll back to the beginning of the cycle when the error occurred. In some cases the erroneous state is corrected by copying a value from the fault-free processor to the faulty processor. The architecture, microarchitecture, and VLSI implementation of the MP, emphasizing its error-detection, error-recovery, and self-diagnosis capabilities, are described.

Tamir, Yuval↗
NASA NTRS1991

Integrated energy balance analysis for Space Station Freedom

An integrated simulation model is described which characterizes the dynamic interaction of the energy transport subsystems of Space Station Freedom for given orbital conditions and for a given set of power and thermal loads. Subsystems included in the model are the Electric Power System (EPS), the Internal Thermal Control System (ITCS), the External Thermal Control System (ETCS), and the cabin Temperature and Humidity Control System (THC) (which includes the avionics air cooling, cabin air cooling, and intermodule ventilation systems). Models of the subsystems were developed in a number of system-specific modeling tools and validated. The subsystem models are then combined into integrated models to address a number of integrated performance issues involving the ability of the integrated energy transport system of Space Station Freedom to provide power, controlled cabin temperature and humidity, and equipment thermal control to support operations.

Tandler, John↗